PROVN OF PARKING WITH HARD STANDING FOR JCOs OR BEHIND BLDG NO 81 OF GRN BN SPL REPAIR TO BLDG NO P 2F JCOs OR GUEST ROOM AT ARO AT ALMORA UNDER GE RANIKHET

Amount

BOQ ( Sch 'A') B/R items Demolition of cement concrete (unreinforced) in ground floors and pavings incuding terrazzo topping n.exc 15cm thickness (below or above ground level) and disposal of unserviceable materials, debris and rubish to a distance not exc 50m complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified & directed.

Taking down cement or cement lime plaster from brick work or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M & L for 25 mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone agg) as in floors and finishing the top surface even and rough to receive the topping layer or tiling complete all as specified and directed.

M & L for 15 mm thick screed bed or bedding layer in CM 1:6 to receive floor finishes complete all as specified and directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or rectangular) area of each tile exc. 0.06 Sqm but not exc. 0.11 Sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for 10 mm thick backing coat or bedding in CM 1:3 to receive wall finishes complete all as specified and directed.

M & L for glazed ceramic coloured tiles 300mm x 200mm x 5.5mm thick as on vertical surface of wall such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for 75 mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection or sub floor or sub base or similar work, laid in bays including necessary form work finished fair and even complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base finishing the surface fair and even Complete all as specified and directed.

M&L for chequered cement concrete tiles of size 300x300x 22-25 mm thick coloured rubber pressed glossy finish, set and jointed in neat cement slurry and pointed in white or colour cement and match the surace of tiles as in foor/staps, complete as all specified and directed

M&L for rendering 15 mm thick on fair faces of brick work or stone masonry or concrete surfaces in cement mortar 1:4 and finished fair and even without using extra cement includig mixing of water proofing compound of approved as per manufacturer's instruction complete as all specified and directed. Note:- WPC shall be measured & paid seprately as supply only.

Supply only Integral water proofing compound.

M & L for 15mm thick rendering in cement mortar 1:6, surface finished even & smooth using extra cement with a dubbing out average 10mm thick in CM 1:6 on irregular face of walls, complete as all specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 on ceiling and finished even and smooth without using extra cement complete as all specified and directed.

M&L for preparing newly plastered wall surfaces and applying two coat of distemper oil emulsion over a coat of primer (Priming the plastered and other surface preparatory to distempering) complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed.

M&L for complete removal of existing treatment for preparing old painted surfacess and applying two coat of distemper oil emulsion over a coat of primer complete all as specified and directed.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment for preparing old painted surfacess and applying two coat of cement base paint over a coat of primer complete all as specified and directed.

M&L for Providing and applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete all as specified and directed.

Taking down chowkhat or frame area exc 1.50 Sqm but not exc 4.00 Sqm each with shutter (without taking off shutters from the frames) and removing from site complete all as specified and directed.

Taking down door shutter of any description exc 1 Sqm but not exc. 2 Sqm each complete all as specified and directed.

M & L for 2nd class hard wood 35mm thick plain, framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P commercial ply or 12 mm veneered particle board with commercial veneering on both faces complete all as specified and directed.

S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, (without sash bars), edges of framing plane, chamfered or rounded fitted with cut or mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, section-8, clause 8.24 (a) complete all as specified and directed.

S&F Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 45 x 70 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete all as specified and directed. Note:- M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately

S&F Factory made single extruded WPC (wood polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrwal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N mm2 modulus of elasticity 850 N / mm2 and resistance to spread of flame of Class A catogary with property of being termite/ borer proof, water/ moisture proof and fire retardanat and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, complete all as specified and directed. (Note:- stainless steel butt hinges and necessary SS screws shall be paid separately.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness incl cover fillets etc complete all as specified and directed.

Supply & fixing of powder coated GI snap grid frame work for false ceiling comprising of the following sections for making partitions of 605x605 mm size fixed to walls with rawl plugs & screws and hanged to roof with and including 2mm dia GI wire suspender of suitable length and butterfly clips, size of main tee shall be 37mmx24mmx0.3 mm thick , cross tee shall be 28mmx24mmx0.3mm thick and wall angle shall be 24mmx24mmx0.3 mm thick complete all as specified and directed.

Supply & fixing 4mm thick non asbestos E-board cement building board for insulation and accoustic purpose, 600 x 600 mm size fixed with staples on snap grid as in ceiling complete all as specified and directed.

S&F 2nd class hard wood glazed and skeleton shutter 30mm thick open rebated and prepared to receive glass gauge etc with sash bars divided into square with plain camfered on rounded , mitred and rebated sash bars, any numbers, size of memeber of shutter as specified in SSR Pt-I Sec-8, clause 8.20 (b) complete all as specified and directed.

S & F 100 mm size butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed

S & F 75 mm size butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed

S & F 200mm long aluminum, anodised barrel tower bolt of extruded section and fixed complete all as specified and directed.

S & F 150mm long aluminum, anodised barrel tower bolt of extruded section and fixed complete all as specified and directed.

S & F for 300mm long mild steel sliding door bolts, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

M & L for prepration of newly or previously un-treated steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds with putty or fixed with beads complete all as speciifed and directed.

S & F 3 mm thick plain Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or Stainless steel wire staples complete all as specified and directed.

S & F in repairs Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or Stainless steel wire staples complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing complete all as specified and directed.

S&F GI water tubing of 15mm dia ,medium grade conforming to IS-1239(Part -1) with and including all GI fittings such as bends,tees, short pieces ,connectors, elbows, reducers, union sockets etc & fixed to walls,ceilings, & laid on floors complete all as specified and directed.

Refixing of old 15 mm bore steel tubing and connections in new or old position (walls, ceiling, floors etc.) complete all as specified and directed. Note:- Old serviceable GI tubes retrived from item no-42 above shall be reused under this item.

S& F Ball brass valve 20 mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S & F fixed in repairs vitreous china wash basin, white, flat back, size 550mm x 400mm, (flat back or angle back type) including brackets and including cutting for and pinning in ends of brackets or erecting stand, complete all as specified and directed.

S & F in repairs 15 mm bore brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repairs 15mm bore stop valves, cast copper alloy, fency type chromium plated with long shank & cup (concealed) , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F in repairs bib taps, cast copper alloy, 15 mm dia, Chromium Plated, fancy type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified and directed.

S&F in repairs toilet paper holder with flat recessed type stainless steel complete all as specified and directed

S & F 20mm Dia Aluminium alloy anodised curtain rod decorative fency type with brackets complete all as specified and directed.

S & F in repair PVC connections 15mm dia , 450mm long, , with PTMT nuts & washers at both ends complete all as specified and directed.

S & F in repairs water closet pan vitreous China wash down (pedestal pattern), (excluding flushing cistern and flush pipe) including connections to drain (or outgoing pipe) and to flushing pipe, anti-syphonic pipe, etc complete all as specified and directed.

S&F in repairs PVC low level flushing cistern, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets, connection to pipe complete all as specified and directed.

S&F in repair 600mmx450mm bevelled edge looking mirror and fixed to wooden plug with CP brass screws and cup washers complete all as apecified & directed.

M&L for 75mm dia PVC floor trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B1 (using 20 mm graded stone aggegate) complete all as specified and directed.

S & F in repair 75 mm bore cast iron soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls complete all as specified and directed.

S & F in repair 75mm bends of any radius complete all as specified and directed.

S&F 75mm cast iron cowls complete all as specified and directed.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M in depth for foundation, etc., and getting out in Hard/ Dense soil complete all as specified and directed.

Demolation and breaking up drain pipes 150 mm (salts glazed ware ,AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

M & L for 150 mm dia Salt Glazed stone ware grade 'A' drain pipes laid in trenches and jointed in CM 1:1 as specified complete all as specified and directed.

M & L for PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150mm bore complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in hard/dense soil complete all as specified and directed.

Removing Excavated soil exceeding 1.00 KM but not exceeding 1.50KM and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.

Dismantaling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strenth of 550 Mpa as in roof covering / clading to wall , fixed with self tapping screws & fixed with L type or J- type or crannked hooks bolts in lieu of screw complete all as specified and directed.

All as per item No 67 here-in-before but fixing only with and including all necessary fixing arrangement complete all as specified and directed. NOTE:- OLD SHEET OBTAINED FROM DISMANTLING SHALL BE REUSED UNDER THIS ITEM.

S&F Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick as in ridge of an colour having tensile strenth of 550 Mpa as in roof covering / clading to wall , fixed with self tapping screws & fixed with L type or J- type or crannked hooks bolts in lieu of screw complete all as specified and directed.

All as per item No 69 here-in-before but fixing only with and including all necessary fixing arrangement complete all as specified and directed. NOTE :- OLD SHEET OBTAINED FROM DISMANTLING SHALL BE REUSED UNDER THIS ITEM.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M & L for MS Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 290 gde E -165 complete all as specified and directed.

Demolition of brick work or stone / boulder masonry including all quions, arches, pillars, etc built in cement mortar or cement lime mortar complete all as specified and directed.

M&L for brick work with sub class 'B' brick straight or curved on plan to any radius in half brick thick walls, built in CM (1:4) complete all as spcified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for extra for forming fair finished drains or channels 30cm inner girth in cement concrete using extra cement including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in surface drains and channels compete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded aggregate) as in coping/ kerb/ bed blocks for hold fast/ side of interlocking paver blocks etc including weathering and throating as required including necessary form work complete all as specified and directed.

S&F in repairs 28mm dia fancy type drapery rod of mild steel duly powder coated wood finished with fixing bracket and fancy type finale, stops etc complete all as specified and directed

S & F in repairs jet spray 1.00m long flexible LDPE pipe fabricated and jointed with jet of 100mm long on one side and socket joint of 15mm dia. on other end, steel plate with adjustable hole and a groove to adjust the nozzle of jet, shall be chromium plated brass complete all as specified and directed.

S&F chromium plated soap dish of standard size complete all as specified and directed

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum and getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm thick and removing surplus excavated material to a distance not exc 50M and depositing where as directed and making good surfaces in hard/dense soil complete all as specified and directed.

M & L for plain cement concrete 1:3:6 Type C-2 (using 40mm graded stone aggregate) as in embedding of posts, filling and mass concrete complete all as specified and directed.

S & F for mild steel posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work confirming to Fe-290 Gde Fe-165 complete all as specified and directed.

M& L for Hard core of gauge n exc. 63 mm,Broken stone and boulders deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Machine Pressed precast concrete interlocking paver tile block , glossy finish coloured as approved by GE any shape & size confirming to is 15658- 2006 of 80 mm thikness M-40 Grade with grey cement and no pigments complete all as specified and directed

S&F 2nd class hard wood (SAL) plain, solid, straight chowkats and frames, wrought framed rebated on the solid, rounded or chamfered put together with glue, pinned at joints and fixed to any position complete all as specified and directed

S&F 125mm size aluminium, anodized handle plate type bolt of extruded section and fixed complete all as specified and directed

M&L for preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint over a conat of pink primer complete all as specified and directed

M&L for fine (sand) for cushion of paver block Avg 35 to 40 mm thick under interlocking tiles complete all as specified and directed

SURYA CONSTRUCTION

M/S BHATT ENTERPRISES

SS Construction Co