Construction of Building for school of Fundamental Research in Ayurveda at Thripunithura , Ernakulam , phase IV

Amount

Civil work

od217201/2022_2023 : Filling with contractorsown earth in layers not exceeding 20 cm in depth , breaking clods, watering, rolling each layer with 0.5 tonne roller or wooden or steel rammers , and rolling every 3rd layer and top -most layer with power roller of minimum 8 tonnes and dressing up ,in embankments for roads , flood banks , marginal banks and guide banks or filling up ground depressions , lead upto 50m and lift upto 1.5 m inluding royality for earth conveyance of earth all complete

16.79 : Providing , laying spreading and compacting graded stone aggregate ( size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub - base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer - in- Charge.

4.1.5 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

10.2 : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

12.50 : Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

od216028/2022_2023 : Providing and Laying HDPE pipes (IS : 4984)on land portion including conveying within initial lead, aligning the pipes and lowering the pipe in position into the trenches already made, back filling and leveling the trenches including all labour charge, hire for appliances etc. complete but including cost of pipe and fittings.<br>110 mm OD HDPE pipe

2.10.1.2 : Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

19.6.2 : Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand) including testing of joints etc. complete:150 mm dia R.C.C. pipe

18.35.1 : Constructing masonry chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 grades stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 ( 1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

od218360/2022_2023 : Supplying and fixing at site 2000 mm double main entrance glass door made with 12 mm toughened glass. The door should contain with floor spring for both doors and 300 mm long D handles on both sides of each doors and 2 nos Patch lock to close the same. 1 P. Cost shall be including all materials, labour, lead and fixing charges

od218361/2022_2023 : Providing and fixing at site 12mm Clear Toughened glass using Dorma patch fittings with MS structural Support with 82x145x4.8mm RHS with Baseplate . Cost shall include all material, labour, lead, fabrication charges & fixing charges

od218362/2022_2023 : Providing and fixing of 8mm thk Fiber cement Board Exterior grade above Glass partition as false ceiling with two skin (both inside<br>and outside) using Aluminium and MS support to make it rigid. . Cost shall be including all materials, labour, lead and fixing charges . (Painting Not<br>included in our scope)

Electrical Wiring

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.12 : Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.25 : Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

1.31 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

od202527/2022_2023 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

od214667/2022_2023 : Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the surface/recessed steel/PVC conduit as required<br>1 run of Cable including cost of PVC conduit

od214830/2022_2023 : Supplying and fixing dual port face plate of size 75mmX75mm

od214876/2022_2023 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 nos 3 pin 5/6 amps modular socket outlet and 1 no 5/6 amps modular switch, connection etc. as required.

od214934/2022_2023 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch with indicator, connection etc. as required.

od214963/2022_2023 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required both in independent positions.

od215010/2022_2023 : Wiring for two light points with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with one independent switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.<br>Group C

od215014/2022_2023 : Wiring for Three light points with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with one independent switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.<br>Group C

od215580/2022_2023 : Wiring for four light points with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with one independent switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.<br>Group C

od215582/2022_2023 : Wiring for five light points with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with one independent switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.<br>Group C

od215584/2022_2023 : Wiring for six light points with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with one independent switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.<br>Group C

od215586/2022_2023 : Wiring for seven light points with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with one independent switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.<br>Group C

od215587/2022_2023 : Wiring for eight light points with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with one independent switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.<br>Group C

1.7.4 : Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required2 X 6 sq. mm + 1 X 6 sq. mm earth wire

od215695/2022_2023 : Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required 4 X 6 sq. mm + 1 X 6 sq. mm earth wire

od215950/2022_2023 : Supplying and fixing bulkhead on the existing modular plate switch box including connections but excluding modular plate etc. as required.

MCCB, MCB and DB's

2.5.1 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)4 way (4 + 12), Double door

2.5.2 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)8 way (4 + 24), Double door

2.3.1 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator6 way, Double door

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

od215132/2022_2023 : Providing and fixing following rating and breaking capacity and pole ELCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required<br>40 Amp, 30 mA, DP ELCB

od215612/2022_2023 : Providing and fixing following rating and breaking capacity and pole MCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required<br>40A 4P MCB

od215898/2022_2023 : Supply, Design, Erection , Testing and Commissioning of following, lift panel fabricated out of 14SWG CRCA sheet. Top cable entry for incoming and outgoing feeders <br>Incomer <br>1. 63A 4P MCB Isolator - 1no<br>Outgoing<br>1. 40A 4pole 100mA ELCB - 1 No<br>2. 25A DP MCB - 1 No<br><br><br>

Cable Tray

4.6.2 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.150 mm width X 50 mm depth X 1.6 mm thickness

4.6.4 : Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.300 mm width X 50 mm depth X 1.6 mm thickness

Earthing

5.2 : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required

5.6 : Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.8 : Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

5.19 : Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required.

od215938/2022_2023 : Supply and erection of earth bench.

Lightning Conductor

6.4 : Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

6.7 : Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

6.8 : Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

6.12 : Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

MV Cable Laying

7.7.1 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (clamped with 1mm thick saddle)

7.7.2 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

7.7.3 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

7.7.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

HT cable laying

8.2.2 : Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etcAbove 120 sq. mm and upto 400 sq. mm

MV, HT Cable Jointing and End Termination

9.1.21 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 35 sq. mm (32mm)

9.1.23 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 70 sq. mm (38mm)

9.1.25 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 120 sq. mm (45mm)

9.1.26 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 150 sq. mm (50mm)

9.1.29 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.1.31 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 400 sq. mm (82mm)

9.1.33 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

9.1.34 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm)

10.1.4 : Supplying and making indoor cable end jointing with cast resin compound, including, lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:300 sq. mm

Cables and End Termination

od209660/2022_2023 : Supply of the following PVC Insulated Armoured Aluminium HT cable XLPE/ L.T.Cables (XLPE/AYWY/AYFY) Cables through excavated trenches, built up cable trenches, cable trays, hume pipes,including supply and fixing of clamps, nuts and bolts, screws, 'identification tags, route markers etc. required for clamping intervals as necessry.<br>L.T. ALUMINIUM CABLES<br>3.5Cx70 SQ.MM.

od209679/2022_2023 : Supply of the following PVC Insulated Armoured Aluminium HT cable XLPE/ L.T.Cables (XLPE/AYWY/AYFY) Cables through excavated trenches, built up cable trenches, cable trays, hume pipes,including supply and fixing of clamps, nuts and bolts, screws, 'identification tags, route markers etc. required for clamping intervals as necessry.<br>L.T. ALUMINIUM CABLES<br>3.5Cx150 SQ.MM

od209682/2022_2023 : Supply of the following PVC Insulated Armoured Aluminium HT cable XLPE/ L.T.Cables (XLPE/AYWY/AYFY) Cables through excavated trenches, built up cable trenches, cable trays, hume pipes,including supply and fixing of clamps, nuts and bolts, screws, 'identification tags, route markers etc. required for clamping intervals as necessry.<br>L.T. ALUMINIUM CABLES<br>3.5Cx240 SQ.MM.

od209685/2022_2023 : Supply of the following PVC Insulated Armoured Aluminium HT cable XLPE/ L.T.Cables (XLPE/AYWY/AYFY) Cables through excavated trenches, built up cable trenches, cable trays, hume pipes,including supply and fixing of clamps, nuts and bolts, screws, 'identification tags, route markers etc. required for clamping intervals as necessry.<br>L.T. ALUMINIUM CABLES<br>3.5Cx300 SQ.MM.

od209687/2022_2023 : Supply of the following PVC Insulated Armoured Aluminium HT cable XLPE/ L.T.Cables (XLPE/AYWY/AYFY) Cables through excavated trenches, built up cable trenches, cable trays, hume pipes,including supply and fixing of clamps, nuts and bolts, screws, 'identification tags, route markers etc. required for clamping intervals as necessry.<br>L.T. ALUMINIUM CABLES<br>3.5Cx400 SQ.MM.<br>

od214605/2022_2023 : Supply of the following PVC Insulated Armoured Aluminium HT cable XLPE/ L.T.Cables (XLPE/AYWY/AYFY) Cables through excavated trenches, built up cable trenches, cable trays, hume pipes,including supply and fixing of clamps, nuts and bolts, screws, 'identification tags, route markers etc. required for clamping intervals as necessry.<br>L.T. ALUMINIUM CABLES<br>4.0Cx10 SQ.MM.

od214606/2022_2023 : Supply of the following PVC Insulated Armoured Aluminium HT cable XLPE/ L.T.Cables (XLPE/AYWY/AYFY) Cables through excavated trenches, built up cable trenches, cable trays, hume pipes,including supply and fixing of clamps, nuts and bolts, screws, 'identification tags, route markers etc. required for clamping intervals as necessry.<br>L.T. ALUMINIUM CABLES<br>4.0Cx16 SQ.MM.

od214607/2022_2023 : Supply of the following PVC Insulated Armoured Aluminium HT cable XLPE/ L.T.Cables (XLPE/AYWY/AYFY) Cables through excavated trenches, built up cable trenches, cable trays, hume pipes,including supply and fixing of clamps, nuts and bolts, screws, 'identification tags, route markers etc. required for clamping intervals as necessry.<br>L.T. ALUMINIUM CABLES<br>4.0Cx25 SQ.MM.

DG and Metering Unit

od218441/2022_2023 : HT METERING UNIT (OUT DOOR) Supply ,Erection, testing and commissioning of 11KV Cast resin CT/PT unit consisting of 10/5A, class 0.2S, 15VA current transformers, 11KV/110V class 0.2 S, 100VA potential transformers. And Tri vector meter with TOD meter in a suitable weather proof sheet steel enclosure as per state electricity board norms including supply and fixing of Test fuses and 10.0Cx2.5<br>sq.mm armoured copper cable between CT/PT terminal block, control unit and TOD meter .Provision for<br>terminating 3x185 sq mm XLPE cable.

od218442/2022_2023 : 200 KVA DG SET<br>Supply, Erection, Testing and commissioning of 200KVA, 415Volts, 3Phase, 50c/s, Diesel Engine coupled Alternator working at 0.8 p.f. comprising of Starting equipment for the Diesel Engine and including the following. Fixing of diesel tank and supply and fixing of Fuel line for the diesel engine. Supply & Fixing of residential silencer for the engine. Supply and fixing of<br>Exhaust line 25 METER and Aluminium cladding up to top for exhaust line.

Documents and Approval

od218510/2022_2023 : Preparation of necessary documents, forms, drawings, schemes, certificates etc. and getting approval from Fire Inspectorate for the installation. Submitting certificates and arranging inspection, getting sanction and certificate from Fire Department etc. for commissioning of the whole installation in the premises. All expenses except statutory charges shall be paid by the contractor.

od218511/2022_2023 : Preparation of necessary documents, forms, drawings, schemes, certificates,etc. and getting approval from ElectricaI Inspectorate for the installation. Submitting certiicates and arranging inspection, getting sanction and eregisation certificate from Electrical Inspectorate and KSEB, obtaining power allocation and power connection etc. for commissioning of the whole installation in the premises. All expenses except statutory charges shall be paid by the contractor.

Fire Pump Room Requirements

od216455/2022_2023 : Supplying, installation, testing and commissioning of Electric driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required : Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. Suitable HP Squirrel cage induction motor, TEFC,<br>synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered with anti vibration pads. <br>1620 lpm at 88 m Head

od216459/2022_2023 : Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520.1.00 204000.00 Cartage @1% of A Total Total of A+B Rs. Each Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office<br>red colour etc. as required. M.S fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.1620 lpm at 88 m Head

od216460/2022_2023 : Supplying, installation, testing and commissioning of electric driven pressurization pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads. <br>180 lpm at 88 m Head

od216462/2022_2023 : Supply, installation, testing & commissioning of Pressure gauges of suitable range with necessary fittings like unions / colors / reducers, siphon.

od216464/2022_2023 : Providing and fixing rock wool sectional pipe insulation of density 144 Kg/Ch.M. for fire pump exhaust pipes & fittings over a coat of Primer held in position with GI bands of 20 mm x 24 SWG at 300 centre to centre complete as required. For 150/200 mm dia pipe - SP insulation 40 mm thick

od216465/2022_2023 : Providing & fixing of pressure switch in M.S. pipe line including connection etc. as<br>required.

od216466/2022_2023 : Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :50mm

od216467/2022_2023 : Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :65mm

od216468/2022_2023 : Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :80mm

od216469/2022_2023 : Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :100mm

od216470/2022_2023 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 25 mm nominal bore

od216471/2022_2023 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 50 mm nominal bore

od216472/2022_2023 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 50mm

od216473/2022_2023 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 65mm

od216474/2022_2023 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80mm

od216475/2022_2023 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100mm

od216476/2022_2023 : Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 65mm

od216477/2022_2023 : Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :80mm

od216478/2022_2023 : Providing, installation, testing and commissioning of non-return valve of following<br>sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :100mm

od216479/2022_2023 : Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 100 mm dia

od216480/2022_2023 : Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 25mm

od216481/2022_2023 : Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 50mm

od216482/2022_2023 : Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 65mm

od216483/2022_2023 : Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 80mm

od216484/2022_2023 : Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 100mm

od216485/2022_2023 : Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 150mm

Internal Hydrant System

od216523/2022_2023 : Supply, installation, testing & commissioning of Fire Hydrant single outlet gunmetal NB inlet brass spindle 63mm female instantaneous/outlet with PVC blank cap and GI chain as per IS:5290 (ISI Marked)

od216524/2022_2023 : Supply, installation, testing & commissioning of Synthetic fiber circular woven jacketed rubber lined fire hose delivery having 38Kg. Per Cm. Sq. burst pressure, 28Kg. Per Cm. proof pressure, 14Kg. Per Cm. working<br>pressure as per IS:636 (ISI Marked) Type A in 15 Meters length, 63mm dia duly copper via bounded two coupling pair of male female parts any duly instantaneous type, 63mm size as per IS:903 (ISI Marked)

od216525/2022_2023 : Supply, installation, testing & commissioning of Fire Hose Cabinets comprising of the following as per the relevant IS Standard. Short gunmetal pipe 63mm male instantaneous inlet male threaded outlet fitted with 15mm bore nozzle as per IS:903 (ISI Marked). Gunmetal short branch pipe

od216526/2022_2023 : Supply, installation, testing & commissioning of Fire HoSwinging type hose reel complete with 19mm x 40 Mtrs. Thermolplastic hose Type-II. Hose reel drum. 25mm dia gun metal globe valve & nozzle.se Cabintes comprising of the following as per the relevant IS Standard.

od216527/2022_2023 : Fire duct Shutter fabricated out of M.S.sheet & frame, door shall be 900mm x 1200 mm min. & fixed with 6 mm thick Glass, suitable Rubber beeding and Locking arrangement. Quoted rate shall be includes all fasteners etc, and <br> complete shutter shall be powder coated of approved colour both inside with<br>white and red out side.

od216470/2022_2023 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 25 mm nominal bore

od216474/2022_2023 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80mm

od216475/2022_2023 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100mm

od216478/2022_2023 : Providing, installation, testing and commissioning of non-return valve of following<br>sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :100mm

od216531/2022_2023 : Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :150mm

od216483/2022_2023 : Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 80mm

od216484/2022_2023 : Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 100mm

od217708/2022_2023 : Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

od217709/2022_2023 : Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

od217710/2022_2023 : Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1500mm

od217711/2022_2023 : Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT<br>female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1000mm

od217712/2022_2023 : Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories: Pendent Sprinkler

Yard Hydrant System

od216524/2022_2023 : Supply, installation, testing & commissioning of Synthetic fiber circular woven jacketed rubber lined fire hose delivery having 38Kg. Per Cm. Sq. burst pressure, 28Kg. Per Cm. proof pressure, 14Kg. Per Cm. working<br>pressure as per IS:636 (ISI Marked) Type A in 15 Meters length, 63mm dia duly copper via bounded two coupling pair of male female parts any duly instantaneous type, 63mm size as per IS:903 (ISI Marked)

od216525/2022_2023 : Supply, installation, testing & commissioning of Fire Hose Cabinets comprising of the following as per the relevant IS Standard. Short gunmetal pipe 63mm male instantaneous inlet male threaded outlet fitted with 15mm bore nozzle as per IS:903 (ISI Marked). Gunmetal short branch pipe

od216625/2022_2023 : Fire hose cabinet complete in MS, fabricated from 18 SWG CRCA sheet full front glass door and locking arrangement duly painted and suitably mounted on a raised masonry platform / supported from the wall as required (Approx size 750mm x 750mm x 450mm)

od216626/2022_2023 : Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required Single headed Gunmetal

od216627/2022_2023 : Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required 4 way - 100 mm dia M.S. Pipe

od216628/2022_2023 : Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required 4 way - 150 mm dia M.S. Pipe

od216629/2022_2023 : Sealing of Fire shafts at all floor levels by using fire sealant between pipes and RCC slab within shaft area as per drawings and engineer - in - charge.

od216630/2022_2023 : Supply, installation, testing & commissioning of Anticorrosive material for buried pipes with coating of Primer and wrapping with 4 mm thick polymer corrosion resistnt tape as per IS : 10221 with 15 mm overlap as per specificatios.(The piping Qty. included in Item No. 1 above.) etc complete.

od216483/2022_2023 : Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 80mm

od216484/2022_2023 : Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 100mm

od216474/2022_2023 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80mm

od216475/2022_2023 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100mm

Conventional Fire Detection and Alarm System

od216636/2022_2023 : Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections,<br>interconnections as required. 04 loop panel, Addressable fire alarm panel

od216637/2022_2023 : Supplying, installation, testing & commissioning of fault isolator complete with base as required.

od216638/2022_2023 : Supplying, installation, testing & commissioning of addressable fire control module complete as required.

od216639/2022_2023 : Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath complete as required.

od216640/2022_2023 : Supplying, installation, testing & commissioning of addressable manual call point complete as required.

od216641/2022_2023 : Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

od216642/2022_2023 : Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB, MP3 player (including 6 zone button paging station) with seamless integration facility with main fire alarm panel for voice evacuation complete as required. 6 Zone PA Panel

od216643/2022_2023 : Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers complete as required.

od216644/2022_2023 : Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as required.

od216645/2022_2023 : End Termination of above cable to junction boxes using single compression brass type cable glands & pin type tinned copper lugs.

od216646/2022_2023 : Supply, installation, testing & commissioning of MS 100x100x50 mm MS junction box made of 16swg CRCA sheat duly painted with 2 coates of red oxide and 2 cotes of enamel paint, each side cable knot of 19mm dia for cable termination.

od216647/2022_2023 : Supply, installation, testing and commissioning of Single Channel Class D Digital Amplifier 2 x 500 Watts With connection cable to controller.

od216648/2022_2023 : Supply, installation, testing and commissioning of DVD/CD Player with inbuilt USB port.

od216649/2022_2023 : 16 Channel Two Way Communication System Panel with Power Supply, Battery Charger Facility, necessary mounting units , with all accessories

od216650/2022_2023 : 6W Talk Back Speaker unit with all mounting accessories

od216651/2022_2023 : Supply, installation, testing and commissioning of Single Channel Class D Digital Amplifier 1x150 Watts With connection cable to controller.

od216652/2022_2023 : Supply, Installation, Testing & Commissioning of 24 U Rack

Fire Extinguishers

od216833/2022_2023 : Supplying, installing and commissioning portable fire extinguishers of following type & capacity. The requirement shall be based on NOC & drawings. ABC stored pressure type fire extinguisher of 2Kgs. capacity bearing ISI Mark for Fighting ABC & Electrical Class of Fire. The Extinguisher will be Manufactured Strictly as per BIS: 15683:2006 bearing ISI. mark. EN3 615 Approved Powder. ABC 87% MAP.

od216834/2022_2023 : Supplying, installing and commissioning portable fire extinguishers of following type & capacity. The requirement shall be based on NOC & drawings. ABC stored pressure type fire extinguisher of 5 Kgs. capacity bearing ISI Mark for Fighting ABC & Electrical Class of Fire. The Extinguisher will be Manufactured Strictly as per BIS: 15683:2006 bearing ISI. mark. EN3 615 Approved Powder. ABC 87% MAP.

od216835/2022_2023 : Supplying, installing and commissioning portable fire extinguishers of following type & capacity. The requirement shall be based on NOC & drawings.<br>ABC stored pressure type fire extinguisher of 9 Kgs. capacity bearing ISI Mark for Fighting ABC & Electrical Class of Fire. The Extinguisher will be Manufactured Strictly as per BIS: 15683:2006 bearing ISI. mark. EN3 615 Approved Powder. ABC 87% MAP.

od216836/2022_2023 : Supplying, installing and commissioning portable fire extinguishers of following type & capacity. The requirement shall be based on NOC & drawings. water Co2 type, 9Ltr capacity with initial charge complete. bearing ISI Mark for Fighting A Class of Fire. The Extinguisher will be Manufactured Strictly as per BIS: 6234:2003 bearing ISI. mark.

od216837/2022_2023 : Supplying, installing and commissioning portable fire extinguishers of following type & capacity. The requirement shall be based on NOC & drawings.<br>Fire buckets round bottom type minimum 9 Ltrs capacity made of GI with anti corrossive treatment enamel painted, white inside, red outside, over one coat of primer. the word FIRE shall be written outside the bucket in bold black letters.The bucket sholud be with two handles at top for hanging and handle at the side bottom for holding while throwing the contents. One set per 8 car parks DG, Electrical Panel & Transformer room.

Signages

od217034/2022_2023 : Supply, installation, testing & commissioning of Photo luminescent non toxic, non – radio active maintenance free self glowing, exit signs comprising zinc sulphide chargeable crystals which glows in dark printed on u – 1000 photo luminescentcontaining luminescent 111 as base chemical cover with u/v stabilized coating and mounting arrangement for wall / ceiling mounting as per site conditions. The color combination and size of the letters shall be as per IS : 12349. amended up to date. Sinage printed "IN CASE OF FIRE, DO NOT USE THE LIFT, USE STAIR CASE." The size of the board shall be 15.8 CM X 8.3 CM. Fixed at the height of 2 mts. Form finished floor level at strategic locations.

od217035/2022_2023 : Floor Identification Signage shall be of size 15 CM X 60 CM. fixed at strategic locations.

od217036/2022_2023 : Fire hose cabinet shall be of size 8.3 CM X 8.3 CM. fixed at strategic locations.

od217037/2022_2023 : Fire Extinguisher shall be of size 8.3 CM X 8.3 CM. fixed at strategic locations.

od217038/2022_2023 : Manual Call point shall be of size 8.3 CM X 8.3 CM. fixed at strategic locations.

od217039/2022_2023 : Fire order shall be of size 7.5CM X 10.0 CM. fixed at strategic locations.

od217040/2022_2023 : Fire Exit shall be of size 40 CM X 15 CM. fixed at strategic locations.

od217041/2022_2023 : Fire Assembly point direction shall be of size 15.8 CM X 8.3 CM. fixed at strategic locations.

od217042/2022_2023 : Directional Signage shall be of size 15.8 CM X 8.3 CM. fixed at strategic locations.

od217043/2022_2023 : "INCASE OF FIRE BREAK GLASS" point shall be of size 15.0 CM X 20.0 CM. fixed at strategic locations.

Passive CAT 6 for 1G

od217254/2022_2023 : Supply, installation, Testing and Commissioning of Cat.6, U/UTP, AWG23, LSZH cable as per ISO/IEC 60332-3-22. 100 Ohm impedance. Data transmission frequencies of up to 250 MHz. Should comply with the following standards: ANSI/TIA 568C.2, ISO/IEC 60754-2Acidity, ISO/IEC 61034-2 Smoke Density.<br>Cable should have Third party ETL verified test certificate for long distance and short distance.

od217255/2022_2023 : Supply, installation, Testing and Commissioning of CAT 6 UTP outlets shall meet or exceed Category 6 transmission requirements for connecting hardware, as specified in TIA/EIA 568-B.C.2 Commercial Building Telecommunications Cabling Standard and ISO/IEC 11801:2002 Second Edition. The 8-pin<br>modular (RJ-45) jacks shall comply with IEC 60603-7-4. The information outlet shall have a Current Rating of 1.5 A at 20°C to support the PoE and PoE+ applications, The information outlet will have insertion life of 750 cycles minimum. Outlet shall be available in different color as per site condition.

od217256/2022_2023 : Supply, installation, Testing and Commissioning of CAT 6 LSZH U/UTP RJ45 1mtr Patch Cords shall be equipped with 8-pin modular plugs on each end. The cordage sheath shall be made of Low-Smoke, Zero Halogen (LSZH) as per ISO/IEC 60332-3-22: Vertical Flame Spread test. color shall be available based<br>on the site requirement

od217257/2022_2023 : Supply, Installation, Testing and Commissioning of Cat-6 U/UTP patch panels (Unloaded) common molded component 24 port per 1Rack unit, Straight and angled option shall be available as per the site requirement. panel should support the strain relief bar in the back of the panel. Bar should have the cable holders with Velcro to hold the cables in place.

od217258/2022_2023 : Supply, Installation, Testing and Commissioning of Face plate : shall be available in 1 port square versions with white color. Material shall be high impact, flame retardant, UL-rated 94 V-0, thermoplastic. Flammability Rating: UL 94 V-0, Shall have inbuilt shutters to prevent dust to accumulate on the information outlets which are not in use. Including supply and installation of metal box.

od217259/2022_2023 : Supply, Installation, Testing and Commissioning of Face plate : shall be available in 2 port square versions with white color. Material shall be high impact, flame retardant, UL-rated 94 V-0, thermoplastic. Flammability Rating: UL 94 V-0, Shall have inbuilt shutters to prevent dust to accumulate on the information outlets which are not in use. Including supply and installation of metal box.

Passive, Fiber Backbone - OM3

od217367/2022_2023 : Supply, Installation, Testing and Commissioning of OM3, (50/125/250) Multimode cable which can support up to 10 /40/100G application, Indoor/outdoor, LSZH/PE, UV Stabilized, Single Jacket/Single Armor, Gel-Free, Loose Tube Cable, Corrugated steel tape armor is strong yet flexible, providing<br>additional crush and rodent protection. Number of core shall be 6F, Compression Test Method-IEC 60794- 1 E3, Flex Test Method-IEC 60794-1 E6, Impact Test Method-IEC 60794-1 E4, Strain Test Method-IEC<br>60794-1 E1, Regulatory Compliance: RoHS 2011/65/EU compliant, Jacket UV Resistance-UV stabilized

od217368/2022_2023 : Supply, Installation, Testing and Commissioning of OM3 24F Fiber panel shall be made of metal with powder coated which shall Accepts one front faceplate made of metal and two Splices tray with three trays each. The width shall be 19 inches and height of 1U (1.75 inches), with a maximum of 18 inch depth, The shelf/LIU shall be sliding face plate panel, 1U, Panel shall have 12 Duplex LC Adapters 24 LC Pigtails, Panel shall be Drawer style for easy access to back side and required cable entry and gromet shall be provided

od217369/2022_2023 : Supply, Installation, Testing and Commissioning of OM3 12F Fiber panel shall be made of metal with powder coated which shall Accepts one front faceplate made of metal and two Splices tray with three trays each. The width shall be 19 inches and height of 1U (1.75 inches), with a maximum of 18 inch depth, The shelf/LIU shall be sliding face plate panel, 1U, Panel shall have 6 Duplex LC Adapters 12 LC Pigtails, Panel shall be Drawer style for easy access to back side and required cable entry and gromet shall be provided

od217370/2022_2023 : Supply, Store, Installation, Testing and Commissioning of OM3 fiber patch cord shall be LC to LC Duplex, Fiber Optic Patch Cords 3m 50/ 125 micron, Cable Sheath shall be made of LSZH, Cable Diameter shall be 1.6 mm , Ferrule shall made of Ceramic., ROHS/ELV Compliant

Network Switch

od217443/2022_2023 : Supply, installation and commissioning of Core Switch - Layer 3 Fully Managed enterprise grade stackable 24 Port Port 10G SFP ports with 2 Port 40G/100G ,Should be support redundant power supply ,880Gbps Switching Capacity , throughout rate of 1300Mpps above, with required licenses along with required accessories. ACLs Support for up to 3K entries, VRRP, BGP, OSPF from day one with 10G Stacking

od217444/2022_2023 : Supply, installation and commissioning of Access Switches - Layer 2 Managed enterprise grade 24 Port 1G PoE+ Ethernet ports with 4 nos of SFP+ ports uplink, PoE+ support with a power budget of up to 370W or higher & Minimum 56gbps Switching Capacity and 83 Mpps throughput Capacity, with required<br>licenses along with required accessories. Link Aggregation Control Protocol (LACP) Up to 8 ports with 10G Stack with DAC.

od217445/2022_2023 : Supply, installation and commissioning of 10G SFP MM Transceiver Which should be from Same OEM

NexGen Firewall

od217497/2022_2023 : Supply, installation and commissioning of 16 and Above GE RJ45 ports (including 2 x WAN ports, 1 x DMZ port, 1 x Mgmt port, 2 x HA ports, 16 x switch ports with 4 SFP port shared media), 4 SFP ports, 2x 10G SFP+ , 480GB onboard storage, dual power supplies redundancy, NGFW Throughput 1.4Gbps or Above ,

od217498/2022_2023 : Supply, installation and commissioning of 10G SFP MM Transceiver Which should be from Same OEM

od217499/2022_2023 : Supply, installation and commissioning of Centralized log & analysis appliance - 2x GE RJ45, 4TB storage, up to 25GB/Day of logs.

Network Racks

od217567/2022_2023 : Supply, installation and commissioning of Floor mounted 42U 600x 1000D Server Rack with front perforated Door and Rear Split Perforated Door ; 1 x1Ph, 230V, 5/15A, Vertical standard rack mount power distribution unit with 12 X Indian Round Pin - PDU Rating 3.6KVA;Mounting Hardware and kits; with cooling fan -4 Qty ,Hardware Kit with Earth Kit

od217568/2022_2023 : Supply, installation and commissioning of Wall mounted 15U 19" Network rack with Side Cable Organiser; 1 x1Ph, 230V, 5/15A, Vertical standard rack mount power distribution unit and 2 Cooling Fan

Accessories

od217585/2022_2023 : Supply, Installation, Testing and Commissioning of User Phone Integrated POE<br>224 X 96 dot matrix grey scale backlit LCD XML support 24 line keys with bi-colour LED (Red, Green) 4 soft keys plus Help & Exit Seven-colour indication LED Full-duplex speaker phone Dual port 10Base-T/100Base-TX network switch<br>Power over Ethernet IEEE 802.3af compliant 2-step adjustable base Modular design supporting upgrade to 32 button Direct headset connectivity

od217597/2022_2023 : SITC of 20 mm PVC Conduit with all fixing accessories through wall/ceiling etc

od217598/2022_2023 : SITC of 25 mm PVC Conduit with all fixing accessories through wall/ceiling etc

od217599/2022_2023 : GI Unperoferated Cable Tray and cover with 150 mm width X 50 mm depth X 1.6 mm thickness (ISI Grade) and all fixing accessories such as threaded rod, unistruct channel support etc. (This item is for laying UTP cables with out conduit, Pulll box should consider for connecting conduit to cable tray)

od217600/2022_2023 : 50 mm HDPE pipe Black colour with all installation accessories

od217601/2022_2023 : Wire Basket -SP Straight 100-300, 2 meters including accessories

od217602/2022_2023 : White print-on area, 10 – 6 AWG wire/cable, Cat. 5e/6/6e UTP and Cat. 5e FTP cable, 100/cassette Hook and Loop 20' Roll, Standard Cross Section.(6.3 Mtr ), 7 Sq MM Heat Shrink Label Tubing -100 Mtr Roll , Cable Tie Items & all installation accessories

od217603/2022_2023 : Project Design ,Documentation and Management, As built drawing in Soft copy and 2 sets of laminated colour prints in A1. Training and guidence to clients staff/ operators etc.

od217604/2022_2023 : 25 Years performance warranty certificate for Passive Networks ( Note : Bidder Submit OEM MAF along with commercial Porospal for checking the genuinity of products (For Active and Passive Items )

UPS and Related Works

od217727/2022_2023 : Supply, fixing and installation of Modular UPS system with more than 5 KWA rating per module, with more than 75 KWA KVA rating with unit power factor and efficiency more than 90 percentage in both online and eco modes. With more than 100 percentage overload capacity. With Charger controller, bypass module availability and isolation transformer.<br>The UPS should be supported with SMF type battery of capacity more than 75ah 12V with back up duration note less than 30mins and rack.<br>

1.7.2 : Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required2X2.5 sq.mm+1X2.5 sq.mm earth wire

1.7.9 : Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required4 X 6 sq. mm + 2 X 6 sq. mm earth wire

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

od214934/2022_2023 : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch with indicator, connection etc. as required.

od218319/2022_2023 : Supply, Laying & clamping at site of Copper earthing conductors inclusive of providing earthing terminations and bracing of the terminations etc. <br>25 x 3mm Copper Strip. 10SWG Copper wire.

od218320/2022_2023 : Supply, Design, fabrication, erection , testing and commissioning of following Cubicle type, fully compartmentalized LT Switchboards dust tight and vermin proof, fabricated out of 14/16 SWG CRCA sheet, chemically treated and powder coat the panels with approved shade. The Switchboards should have a Set of suitably rated TPN Aluminum busbars with the specified current and fault level, Insulated with heat shrinkable, color coded PVC Sleeves and supported using DMC/ SMC Pillar or Finger type busbar supports. The design should be as per the standards of the State Electrical Inspectorate. (All indication lamps should be LED type, ALL MCCBs should be with rotary handle) <br>UPS bypass panel<br>Top cable entry for incoming and outgoing feeders. Fabricated out of 16SWG CRCA sheet<br><br>1) Busbars:<br>125A 4P AL BUSBAR<br>Earth bus - 25 x3mm CU.<br><br>2) Incomers:<br>1nos 125A 4P ON LOAD COS and inter connection mechanism-1set<br><br>3) Meters & Indications:<br>Indication Lamps 3nos, 2A Control (BYEPASS ON) - 1nos<br>Indication Lamps 3nos, 2A Control (UPS ON)- 1nos<br><br>4) Outgoings:<br>1nos 125A 4P ON LOAD COS and inter connection mechanism with 4nos 100A fuse TPN SPD(10/350µs) 100kA,(8/20µs)25/100kA with indication-1set<br>

AAYKAYCONSTRUCTIONS

LATHA SURESHBABU