Kodenchery Branch Interior, Electrical and Air Condition Works

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum plain board conforming to IS : 2095-Part 1

Gypsum Step Ceiling : Providing and fixing Gypsum Step ceiling with width/ depth less than or equal to 300mm as per approved design.Frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS :277 ,ie, perimeter channels 0.5 mm thick 27 mm high having flanges of 20 and 30 mm long to be fixed as per design intent and thick 12.5 mm thick tapered edge gypsum plain board conforming to IS :2095-Part 1 to be fixed on to the framework using 25 mm long drywall screw.Finish the joints using jointing compound and joint tap as per manufacture specification. Including cost and conveyance of all materials labour charges etc.complete as per direction of Engineer-in-charge. The visible Vertical Sides will be measured .

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum moisture resistant board

Toughened Glass Door:120CM Providing and fixing door of 12mm thick Toughened glass door (Saint Gobain) with dorma kaba BTS 75 120kg patch fittings (Floor Spring, Top patch, pivot Pin, Bottom patch) dorma Center lock and handle 24".Including all cost and conveyance of materials, labour, etc complete.

Toughened Glass Door:90CM Providing and fixing door of 12mm thick Toughened glass door (Saint Gobain) with dorma Aido XLC 4000 patch fittings (Floor Spring, Top patch, pivot Pin, Bottom patch) dorma Center lock and handle 24".Including all cost and conveyance of materials, labour, etc complete.

12mm Toughened Glass Partition with plywood frame : Providing and fixing 12mm thick Toughened glass(Saint Gobain) Partition System (upto a height of 300cm ) with 12mm ply and 1mm lamination as per design intent.Including all cost and conveyance of materials, labour etc complete.

Etching Sticker Work: Providing and fixing Etching Sticker as per design intent using suitable adhesive as per manufacture's Specification.Including all cost and conveyance of materials, labour etc complete.

Providing partition wall 80mm/100mm thick using plywood of thickness 12 mm double layer, with a plywood core.Finished with 1mm white or theme lamination on both sides. No quantity is measured in running meter and Quantity is measured only for partitions below the false ceiling.Including cost and conveyance of all materials labour charges etc. complete.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built-up standard tubular sections/ appropriate Zsections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom, and sides with required EPDM rubber/ neoprene gasket, etc. Aluminium sections shall be smooth, rust-free, straight, mitered, and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions ofEngineer-in-charge. (Glazing, paneling, and dash fasteners to be paid for separately)For the fixed portion, MATERIAL (i)External member of the frame (Jindal section no 4605) (ii)Internal member of the frame (Jindal section no 4604) (iii)Aluminium snap beading on both sides (Jindal section no 4407) (iv)Angle cleat 38x38x4.8mm, (v)C.P. brass/stainless steel screws 20 mm for cleat angle (vi)Chromium plated Brass screws 20 mm (vii)Polyester powder coating 50 microns on aluminium sections