New office complex for PM-IBP and PM-ARP

Amount

Area clearing

Area clearing/Clearing grass and removal of the rubbish up to a distance of 200 m outside the periphery of the area cleared.

Earthwork in excavation

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Soling in foundation

Soling with rough stone of size 200 mm, well packed and filling voids with stone chips and required profile with hammer dressed stones having no side less than 15 cm, with minimum depth of 20 cm including preparing the bedding surface etc. all complete.

Shuttering works up to Plinth level

Centering and shuttering including strutting, propping etc. and removal of form work for:Foundations, footings, bases for columns

PCC (1:4:8) up to Plinth level

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size).Cement supplied by KMML.

Steel work up to plinth level

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more. TMT bars supplied by KMML

Shoring/ Close timbering

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete (Measurements to be taken of the face area timbered).Depth exceeding 1.5 m but not exceeding 3 m

RCC works up to plinth level

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal sizeRequired cement shall be supplied by KMML

Anti termite treatment in trenches and basement

Providing and injecting with approved quality chemical emulsion as per IS 6313-1981 part 2 of pre-constructional anti termite treatment and creating a chemical barrier under the all around column pits, foundation, wall trenches, plinth filling, and floor as per the instructions of the engineer.

Solid Block masonry in basement

Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 30 cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

Black bituminous painting in footing and pedestal

Painting with black anti- corrosive bitumastic paint of approved brand and manufacture to give an even shade:Two or more coats on new work

Filling available excavated earth

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Filling red earth

Supplying and filling with red earth in plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering.

Centering and shuttering for columns.

Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

Steel work in super structure

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more (TMT steel bars shall be supplied by company)

RCC work for columns

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. for all level excluding cost of centering, shuttering, finishing and reinforcement :(Cement and TMT steel bars will be supplied by the company)1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Solid Block masonry in super structure

Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete.(Cement supplied by KMML)

Centering and shuttering for lintels

Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

Centering and Shuttering for sunshade

Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges

Centering and Shuttering for Roof slab and Roof beam

Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

Steel work above plinth level

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more (TMT steel bars shall be supplied by company)

RCC work in Lintel, Sunshade, Roof beam, Roof slab and Staircase

Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 15<sup>0</sup> landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).Cement supplied by kmml.

Solid block masonry for Parapet

Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete(The required opc cement for masonry work shall be supplied by kmml at our store)

6 mm Cement plaster

6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand) The required cement will be supplied by the company

12 mm cement plaster

Plastering with 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)(The required cement shallbe supplied by KMML at our store)

Centering and Shuttering for stair cases (Excluding landing)

Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

MS Grills for windows

Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved epoxy primer and 2 coats of epoxy paint all complete.Fixed to steel windows by welding

S.S handrail for staircase

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Wooden frame for doors and windows

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately), using good quality Anjili wood /jack wood

Wooden shutter for doors and windows

Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge. using Anjili/ Jack wood

Wooden paneling/ Glazing panels for doors and windows

Providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured) paneling for paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality Anjili/ Jack wood

Providing and fixing aluminium shutter for ventilations

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing single molded toilet doors

Providing and fixing single molded fiber door with frame and all fittings like latch, tower bolt, hinges etc. maximum size up to 2 sqm for toilet doors.

Providing and fixing mortice lock set for wooden door frames

Providing and fixing mortise lock set of godrej or equivalent approved by Engineer in charge to the wooden door shutter (handle size minimum 8inch)

Providing and fixing tower bolt for wooden doors and toilet doors

Providing and fixing bright finished Stainless Steel(SS) tower bolts (barrel type) with necessary screws etc. complete:200x10 mm

Aluminium fixed frame work for Toilet ventilation

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in ventilator shutters

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float toughened glass panes of 5.00 mm thickness

Vitrified floor tile

Supply and laying first quality vitrified digital tiles of size 1200 x 600mm of approved make like Kajaria/Cera/johnson/somany/NITCO or other approved brand in approved shade and pattern for floors as per architectural design laid on 20mm thick cement mortar 1:4 (1 cement : 4 course sand ) with tile spacer and jointing with with epoxy joint fillers minimum of 5mm thick of matching shades of approved brand, complete.(The required OPC cement shall be supplied by KMML at our store).

Ceramic wall tiles

Providing and fixing premium quality ceramic digital wall tiles of approved brands likeKajaria- Alexis Decor/Nitco/Simpolo conforming to IS : 15622 (thickness to be specified by themanufacturer), in all colours, shades of size 30x60 cms or nearest as approved by Engineer -in-Charge with cement based high polymer modified quick-set tile adhesive ( Water based) conforming to IS : 15477, in average 3 mm thickness.Details of cost for 1 sqmMATERIAL:Ceramic Glazed tiles = 1.00 sqmAdd for wastage & breakage @ 2.5 %0.025 sqmTotal = 1.025 sqm

European Closet

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

Providing and Fixing Health faucet

Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

Providing and Fixing Angle Valve

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

Providing and Fixing Wash basin

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings:Flat back wash basin of size 630x450 mm

Long body tap

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15 mm nominal bore

Providing and Fixing Stop cock

Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore

Providing and Fixing CP shower

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet:150 mm diameter

Providing and Fixing PVC connection pipe

Providing and fixing uplasticised PVC connection pipe with brass unions:45 cm length15 mm nominal bore

Providing and Fixing pillar tap

Providing and fixing C.P brass pillar cock of approved quality.including painting of fittings and brackets, cutting and making good the walls wherever require:15 mm nominal bore

Providing and fixing PVC waste pipe

Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete.Semi rigid pipe40 mm dia

25 mm Concealed pipe

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 12 kgf/cm2

110 mm pipe exposed on wall

Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

110 mm pipe in trench

Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

32 mm PVC pipe exposed on wall

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10 Kgf/cm2 - External work- Exposed on wall

63 mm PVC pipe exposed on wall

Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall

Providing and Fixing 63 mm 45 degree elbow

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63 dia 45 degree Elbow

Providing and Fixing 110 mm 45 degree elbow

Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

Providing and Fixing 63 mm elbow

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow

Providing and Fixing 63 mm Tee

Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes including jointing with PVC solvent cement - 63x63x63 mm dia Tee

Providing and Fixing 110 mm elbow

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

Providing and Fixing 110 mm Tee

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

Providing and Fixing 63 mm dia Bend

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend

Providing and Fixing 110 mm dia Bend

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

Providing and Fixing 63 mm dia reducer

Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63x50 mm dia Reducer

Providing and Fixing 63x63x63 mm dia Door Tee

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -63x63x63 mm dia Door Tee

Providing and Fixing 110x110x110 mm dia Door Tee

Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x110x110 mm dia Door tee

Providing and Fixing 63 mm Door elbow

Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Door Elbow

Providing and Fixing 110 mm Door elbow

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

Providing and Fixing 110 mm vent cowl

Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia Vent cowl

Providing and Fixing 110 mm Offset

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -110 mm dia offset

Providing and Fixing Floor trap

Providing and fixing PVC moulded Floor trap for sanitary pipelines, including jointing PVC pipes with PVC solvent cement and filling gaps with cement grout- Floor trap 4 way/3 way

Providing and Fixing CP gratings

Providing and fixing CP grating of approved quality.Rectangular type with openable circular lid150 mm nominal size square 100 mm diameter of the inner hinged round grating

Providing and Fixing mirror of superior glass

Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm

Providing and Fixing stainless steel soap dish

Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and Fixing CP Towel rod

Supplying and fixing CP Towel rod 45cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Supplying and Installing readymade RCC septic tank

Supplying and installing ready made RCC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately)2. 15 to below 25 flush capacity

Constructing Soak pit

Constructing soak pit 1.20x1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. (Cement required for fixing pipes etc shall be supplied by the company)

Providing and placing on terrace PVC water tank

Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

PVC ball valve

Providing and fixing PVC ball valve (ISI marked) of approved brand for Rigid PVC pipes, including jointing with PVC solvent cement:25mm nominal bore.

Miscellaneous labour for unforeseen works

Miscellaneous Labours

Supply of 1 phase 240 v Distribution board

Supply of 1 phase 240v distribution board in sheet steel enclosure with double door and detachable gland plate,complete with cable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc.as required, without MCCB's/MCBs For concealed flush mounting Make :Standard/havells/ABB/Siemens/hager/Schneider40A,1 phase 12 way Horizontal DB

Supply of double pole RCCB/MCB ( 40A DP isolator)

Supply of double pole RCCB/MCB of the following capacity 40 A DP Isolator(Make:Standard/Havells/ABB/Siemens/Hager/Schneider)

Supply of double pole RCCB/MCB ( 40A, 100mA DP RCCB))

Supply of double pole RCCB/MCB of the following capacity 40 A,100 mA DP RCCB(Make:Standard/Havells/ABB/Siemens/Hager/Schneider)

Supply of double pole RCCB/MCB ( 6A, SP MCB 10 kA)

Supply of double pole RCCB/MCB of the following capacity6A SP MCB 10kA(Make:Standard/Havells/ABB/Siemens/Hager/Schneider)

Supply of double pole RCCB/MCB ( 10A, SP MCB 10 kA)

Supply of double pole RCCB/MCB of the following capacity10A SP MCB 10kA(Make:Standard/Havells/ABB/Siemens/Hager/Schneider)

Supply of double pole RCCB/MCB ( 16A, SP MCB 10 kA)

Supply of double pole RCCB/MCB of the following capacity16A SP MCB 10kA(Make:Standard/Havells/ABB/Siemens/Hager/Schneider

Supply of double pole RCCB/MCB ( 25A, SP MCB 10 kA)

Supply of double pole RCCB/MCB of the following capacity25A SP MCB 10kA(Make:Standard/Havells/ABB/Siemens/Hager/Schneider)

Supply of UTP/Ethernet Cat 6 cable , Make :D-Link, Finolex, Polycab, Lapp

Supply of UTP/Ethernet Cat 6 cable , make:D-link, Finolex, Polycab, Lapp

Supply of Telephone cable

Supply of Telephone cable, twin flat copper PVC insulated, 2x 0.5 sqmm, ISI marked, make: Finolex, Anchor, V-guard, Traco, Sark, Orbit, Polycab

Supply of LED tube light

Supply of LED tube light,20 W(Approximate),230V, 50 Hz AC supply,surface mounting,IP:20 or aboveWarranty:Full warranty of 1 year or above

Supply of LED Bulb

Supply of LED bulb,9W,230V,50 Hz 230V, 50 Hz AC supply, Pin type ,IP:20 or aboveWarranty:Full warranty of 1 year or above

Supply of LED downlight

Supply of LED downlight, 12 W(Approx.), 230 V, 50Hz, AC supply, surface/ceiling mounting, IP:20 or above, Warranty: Fill warranty of one year or above

Supply of ceiling fan

Supply of ceiling fan 1200 mm sweep Make: Orient/Usha/Crompton/Bajaj/Khaithan

Supply of electric calling bell

Supply of Electric calling bell, 230v, 50Hz Make: Anchor/L&T/Legrand

Supply of exhaust fan

Supply of exhaust fan 300mm sweep Make: Orient/Usha/Crompton/Bajaj/Khaithan/Almonard

Supply of 6A switch

Supply of 6A switch, for 1 module, modular, Make: Legrand, Anchor, ABB, Honeywell

Supply of 16A switch

Supply of 16 A switch, for 1 module, modular, Make: Legrand, Anchor,ABB, Honeywell

Supply of 25A switch

Supply of 25A switch, for 1 module, modular, Make: Legrand, Anchor,ABB, Honeywell

Supply of 5-13A multistandard international socket, for 2 module, modular, Make:Legrand, Anchor, ABB, Honeywell

Supply of 5-13A multistandard international socket, for 2 module, modular, Make:Legrand, Anchor, ABB, Honeywell

Suplly of 16A socket, for 2 module, modular. Make: Legrand, Anchor, ABB, Honeywell

Supply of 16A socket, for 2 module, modular, Make:Legrand, Anchor, ABB, Honeywell

Suplly of 25A socket, for 2 module, modular. Make: Legrand, Anchor, ABB, Honeywell

Supply of 25A socket, for 2 module, modular, Make:Legrand, Anchor, ABB, Honeywell

Supply of angle batten, fancy type, Make: Legrand, Anchor, ABB, Honeywell

Supply of angle batten, fancy type, Make: Legrand, Anchor, ABB, Honeywell

Supply of fan step regulator

Supply of Fan step regulator for 2 module, modular(make: Legrand, Anchor, ABB, Honeywell)

Supply of RJ11 Socket, for 1 module, modular. Make: Legrand, Havells, Anchor, ABB, Honeywell

Supply of RJ11 Socket, for 1 module, modular. Make: Legrand, Havells, Anchor, ABB, Honeywell

Supply of RJ45 Socket, for 1 module, modular. Make: Legrand, Havells, Anchor, ABB, Honeywell

Supply of RJ45 Socket, for 1 module, modular. Make: Legrand, Havells, Anchor, ABB, Honeywell

Supply of concealed GI box face plate and frame for 2 module, modular

Supply of concealed GI Box, face plate and frame for 2 module, modular, Make:Legrand, Anchor, ABB, Honeywell

Supply of concealed GI box face plate and frame for 3 module, modular

Supply of concealed GI box, face plate and frame for 3 module, modularMake: Legrand, Anchor, ABB, Honeywell

Supply of concealed GI box, face plate and frame for 4 module, modularMake: Legrand, Anchor, ABB, Honeywell

Supply of concealed GI box, face plate and frame for 4 module, modularMake: Legrand, Anchor, ABB, Honeywell

Supply of concealed GI box, face plate and frame for 6 module, modular Make: Legrand, Anchor, ABB, Honeywell

Supply of Concealed GI box, face plate and frame for 6 module, modularMake: Legrand, Anchor, ABB, Honeywell

Supply of Concealed GI box, face plate and frame for 8 module, modular Make: Legrand, Anchor, ABB, Honeywell

Supply of Concealed GI box, face plate and frame for 8 module, modularMake: Legrand, Anchor, ABB, Honeywell

Supply of materials required for copper point wiring(Approximate 5 meters/point)

Supply of materials required for copper twin point wiring for lights, fans in PVC medium gauge conduit with modular type switch-using 1.5 sq.mm PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq.mm. PVC insulated copper wire as required to complete.(Excluding supply of Fans, Exhaust fans, Lights, Concealed mounting boxes, Plates and Frames, Switches, Sockets and Fan regulators)(Approximate 5 meters/point)

Supply of materials required for copper point wiring(Above for more than 5 meters)

Supply of materials required for copper point wiring for lights, fans in PVC medium gauge conduit with modular type switch-using 1.5 sq.mm PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq.mm. PVC insulated copper wire as required to complete.(Excluding supply of Fans, Exhaust fans, Lights, Concealed mounting boxes, Plates and Frames, Switches, Sockets and Fan regulators)above for more than 5 meters

Supply of materials required for copper circuit wiring with 1.5 sq.mm. PVC insulated copper conductor stranded cable in recessed PVC conduit along with 1 no. 2.5 sq.mm.

Supply of materials required for copper circuit wiring in PVC conduit-with 1.5 sq.mm. PVC insulated copper conductor stranded cable in recessed PVC conduit along with 1 no. 1.5 sq.mm. PVC insulated copper wire for loop earthing as required.

Supply of materials required for copper circuit wiring with 2.5 sq.mm. PVC insulated copper conductor stranded cable in recessed PVC conduit along with 1 no. 2.5 sq.mm.

Supply of materials required for copper circuit wiring in PVC conduit-with 2.5 sq.mm. PVC insulated copper conductor stranded cable in recessed PVC conduit along with 1 no. 2.5 sq.mm. PVC insulated copper wire for loop earthing as required.

Supply of materials required for copper circuit wiring with 4 sq.mm. PVC insulated copper conductor stranded cable in recessed PVC conduit along with 1 no. 4 sq.mm.

Supply of materials required for copper circuit wiring in PVC conduit-with 4 sq.mm. PVC insulated copper conductor stranded cable in recessed PVC conduit along with 1 no. 4 sq.mm. PVC insulated copper wire for loop earthing as required.

Supply of 10 pair telephone junction box and accessories for flush mounting, Make: Syntex, Krone

Supply of 10 pair telephone junction box and accessories for flush mounting, Make: Syntex, Krone

Installation, Testing and Commissioning of LED tube lights

installation, testing and commissioning of LED tube lights complete with all accessories etc. including connection with 1.5 sq.mm PVC insulated copper conductor single core cable etc. as required

Installation, Testing and Commissioning of LED bulbs

Installation, testing and commissioning of LED bulbs complete with all accessories etc

Installation, testing and commissioning of Ceiling mounted LED downlights

Installation, testing and commissioning of ceiling mounted LED downlights complete with all accessories etc. including connection with 1.5 sq.mm PVC insulated copper conductor single core cable etc. as required

Installation of ceiling fans, making connections, testing and commissioning etc. with 1.5 sqmm PVC insulated copper conductor single core cable etc. as required

Installation of ceiling fans, making connections, testing and commissioning, etc. with 1.5 sq.mm PVC insulated copper conductor single core cable etc.as required.

Installation of exhaust fan

Installation of exhaust fan upto 300 mm sweep in the existing opening including modifying the holes to suit the size of the above fan making good the damage, connections, testing and commissioning etc. with 1.5 sq.mm PVC insulated copper conductor three core cable etc. as required.

Installation of calling bell

Installation of calling bell at DCW room making connections, testing and commissioning etc. with 1.5 sq.mm. PVC insulated copper conductor single core cable etc. as required.

Fixing 6/5-13/16/25 amps modular type sockets switches, bell switches, fan step regulators, with interconnections etc. as required

Fixing of 6/5-13/16/25 amps modular type sockets, switches, fan step regulators, RJ11 and RJ45 modular sockets with front plate in surface or in recess including providing and fixing suitable size metal box, inter connections etc. required.

Copper point wiring in PVC medium gauge conduit with modular type switch

Copper point wiring in PVC medium gauge conduit with modular type switchWiring for light point/fan point/exhaust fan point /calling bell/socket point using 1.5 sq.mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq.mm. PVC insulated copper wire as required with modular type switch with non-metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete.

Copper point wiring in PVC medium gauge conduit with modular type switch above for more than 5 meters

Copper point wiring in PVC medium gauge conduit with modular type switchWiring for light point/fan point/exhaust fan point /calling bell/socket point using 1.5 sq.mm. PVC insulated copper conductor stranded cable in recessed PVC conduit including loop earthing using 1.5 sq.mm. PVC insulated copper wire as required with modular type switch with non-metallic inner and outer cover (inner and outer plate) in suitable metal boxes etc. as required to complete.for more than 5 meters

Copper circuit wiring in PVC conduit-Circuit wiring with 1.5 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no 1.5 sq.mm PVC insulated copper wire for loop earthing as required.

Copper circuit wiring in PVC conduit-Circuit wiring with 1.5 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no 1.5 sq.mm PVC insulated copper wire for loop earthing as required.

Copper circuit wiring in PVC conduit-Circuit wiring with 2.5 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no 2.5 sq.mm PVC insulated copper wire for loop earthing as required.

Copper circuit wiring in PVC conduit-Circuit wiring with 2.5 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no 2.5 sq.mm PVC insulated copper wire for loop earthing as required.

Copper circuit wiring in PVC conduit-Circuit wiring with 4 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no 4 sq.mm PVC insulated copper wire for loop earthing as required

Copper circuit wiring in PVC conduit-Circuit wiring with 4 sq.mm PVC insulated, copper conductor, stranded cable in recessed PVC conduit along with 1 no 4 sq.mm PVC insulated copper wire for loop earthing as required.

LAN circuit wiring in PVC conduit-Circuit wiring with UTP/Ethernet cable in recessed PVC conduit as required

LAN circuit wiring in PVC conduit-Circuit wiring with UTP/Ethernet cable in recessed PVC conduit as required

Telephone circuit wiring in pvc conduit- circuit wiring with two core telephone cable in recessed pvc conduit as required

Telephone circuit wiring in pvc conduit- circuit wiring with two core telephone cable in recessed pvc conduit as required

Installation, Testing and commissioning (concealed flush mounting) Distribution board 40 A,1phase 12 way Horizontal DB

Installation, Testing and commissioning (concealed flush mounting) Distribution board in sheet steel enclosure with double door and detachable gland plate , complete with cable entry adaptor box, tinned copper busbars, neutral link, earth bar, din bar, knockouts, interconnections, earth studs etc. as required40 A,1phase 12 way Horizontal DB

Fixing single pole/ three pole/ four pole RCCB, MCB,s in the existing enclosure and giving connections as required 40A Dp isolator

Fixing single pole/three pole/four pole RCCB,MCBs in the existing enclosure and giving connections as required 40A DP Isolator

Fixing single pole/ three pole/ four pole RCCB, MCB,s in the existing enclosure and giving connections as required 40A 100mA DP RCCB

Fixing single pole/three pole/four pole RCCB, MCBs in the existing enclosure and giving connections as required. 40A,100mA DP RCCB

Fixing single pole/ three pole/ four pole RCCB, MCB,s in the existing enclosure and giving connections as required 6A SP MCB 10kA

Fixing single pole/three pole/four pole RCCB,MCBs in the existing enclosure and giving connections as required 6A, SP MCB 10kA

Fixing single pole/ three pole/ four pole RCCB, MCB,s in the existing enclosure and giving connections as required 10A SP MCB 10kA

Fixing single pole/ three pole/ four pole RCCB, MCB,s in the existing enclosure and giving connections as required 10 SP MCB 10kA

Fixing single pole/three pole/four pole RCCB,MCBs in the existing enclosure and giving connections as required 16A, SP MCB 10kA

Fixing single pole/three pole/four pole RCCB,MCBs in the existing enclosure and giving connections as required 16A, SP MCB 10kA

Laying, dressing and clamping of 4X10 sq.mm. AYFY/XLPE cable . Cable shall be supplied by KMML. All other materials required for clamping are under the scope of contractor.

Laying, dressing and clamping of following cables through existing trays/structures/racks/columns etc to the new DB. Cable shall be supplied by KMML. All other materials required for clamping are under the scope of contractor.4X10 sq.mm. AYFY/XLPE cable

Glanding and termination at DB's side of PVC cable 4 X 10 sq.mm AYFY/XLPE cable

Glanding and termination at DB's side of PVC cable using DC glands/ lugs including supply of cable glands, lugs, aluminum crimping sockets, nuts bolts etc. required for this work. Gland earthing as per standards shall be done by the contractor.4X 10 sq.mm AYFY/XLPE cable

Preparation of electrical drawings

Preparation of all electrical drawings and obtaining statutory approval from electrical inspectorate for the new DBs

Santhi constructions

Bidder Name

Santhi constructions

P V CONSTRUCTIONS