Construction of Govt Polytechnic (Phase-II) at Jassowala, Vikasnagar, Dehradun, Uttarakhand

Amount

Section A

DSR NO. 2016- 2.6.1 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. :All kinds of soil.

DSR NO. 2016-2.8.1 Earth work in excavation in trenches for foundation and for pipes cables etc. in ordinary soil including fitup to 1.5m and dressing of sides and ramming bottoms and disposal of surplus excavated earth as directed by the engineer with in a lead of 50m.

DSR NO. 2016- 2.26.1 Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. All kinds of soil

DSR NO. 2016- 2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

DSR NO. 2016- 2.27 Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.

DSR NO. 2016- 2.10.1.2 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil, Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

DSR NO. 2016- 2.1.6 + 2.25 + 1.1.2 Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

DSR NO. 2016- 2.35.3.1 Diluting and injecting chemical emulsion (Chlorpyriphos/Lindane E.C. 20% with 1% concentration), at the rate of one litre per hole at 300 mm c/c to all the horizontal and vertical surfaces of the excavations made for the foundation of the building, soil under floors, apron, back fill material and along all the facesof the walls for PRE-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) as per IS:6313 Part-II.(Plinth area of Building shall be measured for Payment).

DSR NO. 2016- 4.1.3 P/L cement concrete - all works upto plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

DSR NO. 2016- 4.1.6 P/L cement concrete - all works upto plinth level : 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

DSR NO. 2016- 4.1.8 P/L cement concrete - all works upto plinth level : 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 20 mm nominal size)

DSR NO. 2016- 4.1.10 P/L cement concrete - all works upto plinth level : 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

DSR NO. 2016- 4.11 Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

DSR NO. 2016- 4.13 Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7 kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

DSR NO. 2016- 5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

DSR NO. 2016- 5.33.1 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. All works upto plinth level

DSR NO. 2016- 5.33.2 Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge All works above plinth level upto floor V level

DSR NO. 2016- 5.9 Centering and shuttering including strutting, propping etc. and removal of form for :

DSR NO. 2016- 5.9.3 Suspended floors, roofs, landings,

DSR NO. 2016- 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

DSR NO. 2016- 5.9.2 Walls (any thickness) including attached pilasters,butteresses, plinth and string courses etc.

DSR NO. 2016- 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts

DSR NO. 2016- 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers.

DSR NO. 2016- 5.9.20 Suspended floors, roofs, landings, balconies and access platform, with water proof ply 12 mm thick

DSR NO. 2016- 5.9.7 Stairs, (excluding landings) except spiral-staircases

DSR NO. 2016- 5.9.20 For Suspended floor, slab landing etc. with 12 mm thick water proof ply. For chajja.

DSR NO. 2016- 5.11.1 Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

DSR NO. 2016- 5.22.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

DSR NO. 2016- 6.1.1 Brick work with bricks of Ist class in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand)

DSR NO. 2016- 6.1.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR NO. 2016- 6.4.2 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

DSR NO. 2016- 6.13.2 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

DSR NO. 2016- 6.15 Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

DSR NO. 2016- 9.20 Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

DSR NO. 2016- 9.20.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

DSR NO. 2016- 9.20.3 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. Piano hinges IS : 3818 marked with necessary screws

DSR NO. 2016- 9.21 P/F ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters

DSR NO. 2016- 9.21.1 A) 35 mm thick including ISI marked Stainless Steel butt hinges

DSR NO. 2016- 9.21.3 B) 25 mm thick (for cupboard) including ISI marked nickel plated

DSR NO. 2016- 9.62 Providing and fixing ISI marked M.S.Oxidised fitting for door windows.

DSR NO. 2016- 9.62.2 250x16 mm sliding door bolts

DSR NO. 2016- 9.63.1 250x10 mm Tower bolt

DSR NO. 2016- 9.63.3 150x10 mm Tower bolt

DSR NO. 2016- 9.66.1 125 mm handles

DSR NO. 2016- 9.66.2 100 mm handles

DSR NO. 2016- 9.101.2 hanging floor door stopper, Twin rubber stopper

DSR NO. 2016- 9.68.2 200 Casement stays (straight peg type) with necessary screws etc. complete, weighing not less than 120 gms

DSR NO. 2016- 9.23 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

DSR NO. 2016- 9.79.2 Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. 50 mm

DSR NO. 2016- 9.114.1 Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. : Triple strip vertical type

DSR NO. 2016- 9.27.1.1.1 Providing and fixing 35mm thick second class teak wood wire gauze shutters using galvanised M.S. wire gauze of average width of aperture 1.4mm with wire of dia. 0.63 mm for doors, windows and clerestory windows.

DSR NO. 2016- 10.14 Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge:

DSR NO. 2016- 10.14.2.1 (A) "Profile C" Fixing with adjustable lugs with split end tail to each jamb

DSR NO. 2016- 10.14.3.1 (B) "Profile E" Fixing with adjustable lugs with split end tail to each jamb

DSR NO. 2016- 10.15.1 Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

DSR NO. 2016- 9.48.1 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

DSR NO. 2016- 9.51.2 Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm all complete. With 12 mm mild steel U beading

DSR NO. 2016- 10.26.1 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. M.S. tube

DSR NO. 2016- 10.30.2 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 4.0 mm thick glass panes

DSR NO. 2016- 25.08 Design supply & installation of suspended Spider Glozing system designed to withstand the wind pressure as pr IS 875 (Part-III). The Suspended System held with Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having 12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel Spider & bolt assembly with laminated glass fins 21 mm thick. The Glass fins and glass panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless steel brackets & Anchor bolts and at the bottom using SS channel of x25x2mm using fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon bushes and separators to prevent bi-metallic contacts, all complete to perform as per specification and approved drawings. The complete system to be designed to accommodate thermal expansion & seismic movements etc. The joints between glass panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled with non staining weather sealant, so as to make the entire system fully water proof & dust proof. The rate shall include all design, Engineering and shop drawing including approval from structural designer, labour, T&P, scaffolding, other incidental charges including wastage, enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener, anchors, SS channel laminated glass etc. all complete. For the purpose of payment, actual elevation area of Glazing including thickness of joints and the portion of Glass panel inside the SS channel shall be measured. “

DSR NO. 2016- 10.6.1 Supplying and fixing rolling shutters of approved make, made of requiredsize M.S. laths, interlocked together through their entire length and jointedtogether at the end by end locks, mounted on specially designed pipeshaft with brackets, side guides and arrangements for inside and outsidelocking with push and pull operation complete, including the cost of viding and fixing necessary 27.5 cm long wire springs anufactured from high tensile steel wire of adequate strength conforming to IS: 4454 -part 1 and M.S. top cover of required thickness for rolling shutters. 80x1.25 mm M.S. laths with 1.25 mm thick top cover

DSR NO. 2016- 11.41.2 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

DSR NO. 2016- 11.46.2 Providing and laying Vitrified tiles in different sizes (thickness to be specifiedby manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete. Size of Tile 600x600 mm double charged

DSR NO. 2016- 11.39 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete.

DSR NO. 2016- 8.31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make,in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

DSR NO. 2016- 8.2.2.1 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of approve colour.

DSR NO. 2016- 8.2.1.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble. Area of slab over 0.50 sqm

DSR NO. 2016- 11.21.1 Providing and fixing 10mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding and joints filled with acid and/or alkali resisting cement as per IS : 4457 complete as per the direction of Engineer-in- Charge. In flooring on a bed of 10 mm thick mortar 1:4(1 acid proof cement: 4 coarse sand). Acid and alkali resistant tile.

DSR NO. 2016- 11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

DSR NO. 2016- 11.3.1 P/L 40 mm thick Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement

DSR NO. 2016- 11.4 52 mm thick C.C. flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4

DSR NO. 2016- 11.5 62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacture’s specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

DSR NO. 2016- 11.6.1 Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement. 18 mm thick

DSR NO. 2016- 13.1.2 12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

DSR NO. 2016- 13.2.2 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

DSR NO. 2016- 13.3.1 20 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

DSR NO. 2016- 13.16.1 6 mm cement plaster 1:3 (1 cement: 3 fine sand)

DSR NO. 2016- 13.50.1 Applying priming coat : With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood)

DSR NO. 2016- 13.45.1 Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

DSR NO. 2016- 13.47.1 Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

DSR NO. 2016- 13.41.1 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade : New work (two or more coats) over and including water tinnable priming coat with cement primer

DSR NO. 2016- 13.62.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

DSR NO. 2016- 13.26 Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

DSR NO. 2016- 13.8 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

DSR NO. 2016- 19.6.2 Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

DSR NO. 2016- 19.3.2 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :

DSR NO. 2016- 19.4.1.1 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame o f 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR NO. 2016- 19.7.1.1 Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR NO. 2016- 19.8.1.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR NO. 2016- 2.13.1.2 Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth upto 1.5 m, including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth, including consolidating each deposited layers by ramming, watering etc., stacking serviceable material rmeasurements and disposal of nserviceable material as directed, within a lead of 50 m :Ordinary rock : Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

DSR NO. 2016- 19.6.4 P/L non-pressure NP2 class (light duty) R.C.C. pipes with collars. 300 mm dia

DSR NO. 2016- 4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement: 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

DSR NO. 2016- 6.44 Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

DSR NO. 2016- 22.3 Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.

DSR NO. 2016- 22.3 (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarsesand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area.

DSR NO. 2016- 22.3 (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

DSR NO. 2016- 12.54.2 Providing and fixing GI Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing ‘C’ wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets.

DSR NO. 2016- 12.54.2 Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring ‘T’ with : GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holesand having NRC of 0.5, electro statically polyester powdercoated of thickness 60 microns (minimum), including factory painted after bending and perforation.

DSR NO. 2016- 22.7 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

DSR NO. 2016- 22.7 b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

DSR NO. 2016- 22.7 c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

DSR NO. 2016- 22.7.1 e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineerin-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

DSR NO. 2016- 12.21 Providing gola 75x75 mm in cement concrete (1:2:4).

DSR NO. 2016- 17.1.1 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

DSR NO. 2016- 17.7.1 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

DSR NO. 2016- 17.3.1 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

DSR NO. 2016- 17.32.4 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

DSR NO. 2016- 17.35 Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729

DSR NO. 2016- 17.35.1.1 100 mm dia Sand cast iron S&S pipe as per IS: 1729

DSR NO. 2016- 17.35.2.1 75mm diameter :Sand cast iron S&S pipe as per IS: 1729

DSR NO. 2016- 17.73.2 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms

Non Sehule Items P/F Upvc nahani trap 110x110mm dia

DSR NO. 2016- 18.65 Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

DSR NO. 2016- 17.37 Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc.

DSR NO. 2016- 17.37.1 For 100 mm dia pipe

DSR NO. 2016- 17.37.2 For 75 mm dia pipe

DSR NO. 2016- 17.56 Providing and fixing terminal guard :

DSR NO. 2016- 17.56.1.1 100 mm Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 17.56.2.1 75 mm Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 18.74.2 Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

DSR NO. 2016- 17.39 Providing and fixing plain bend of required degree.

DSR NO. 2016- 17.39.1.1 100 mm dia Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 17.39.2.1 75 mm dia Sand cast iron S&S as per IS -1729

DSR NO. 2016- 17.38 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

DSR NO. 2016- 17.38.1.1 100 mm dia Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 17.38.2.1 75 mm dia Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 17.28.2.1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 32 mm dia

DSR NO. 2016- 17.41 Providing and fixing double equal junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete :

DSR NO. 2016- 17.41.1.1 100x100x100x100 mm Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 7.41.2.1 75x75x75x75 mm Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 17.8 P/F white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

DSR NO. 2016- 17.5.2 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern

DSR NO. 2016- 8.10.2 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. Granite Stone of approved shade

DSR NO. 2016- 17.10.1.1 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 510x1040 mm bowl depth 250 mm

DSR NO. 2016- 17.11.2 Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

DSR NO. 2016- 17.41.1.1 Providing and fixing heel rest sanitary bend 100 mm dia Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 17.42.1.1 Providing and fixing double equal plain junction of required degree. 100x100x100x100 mm Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 17.43.1.1 Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.100x100x100 mm Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 17.44.1.1 Providing and fixing single equal plain junction of required degree :100x100x100 mm Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 17.57.1.1 Providing and fixing collar : 100 mm Sand cast iron S&S as per IS - 1729

DSR NO. 2016- 12.41.2 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

DSR NO. 2016- 12.42 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

DSR NO. 2016- 12.42.5.2 110 mm bend

DSR NO. 2016- 12.42.6.2 110 mm Shoe

DSR NO. 2016- 12.42.4.2 110x110x110 mm tee

DSR NO. 2016- 12.22 Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete (1:2:4).

DSR NO. 2016- 12.43.2 Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

DSR NO. 2016- 18.11.1 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 15 mm dia nominal bore

DSR NO. 2016- 18.1 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

DSR NO. 2016- 18.10.2 20 mm dia nominal bore

DSR NO. 2016- 18.10.3 25 mm dia nominal bore

DSR NO. 2016- 18.12 Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc.

DSR NO. 2016- 18.12.4 32 mm dia nominal bore

DSR NO. 2016- 18.12.6 50 mm dia nominal bore

DSR NO. 2016- 18.49.1 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

DSR NO. 2016- 18.52.1 Providing and fixing C.P. brass stop cock of standard design and of approved make conforming to IS:8931 15 mm nominal bore

DSR NO. 2016- 18.17 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

DSR NO. 2016- 18.17.1.A 20mm nominal bore

DSR NO. 2016- 18.17.1 25 mm nominal bore

DSR NO. 2016- 18.17.2 32 mm nominal bore

DSR NO. 2016- 18.17.4 50 mm nominal bore

DSR NO. 2016- 18.58.1.1 Providing and fixing PTMT grating of approved quality and colour. 100 mm nominal dia

DSR NO. 2016- 18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

DSR NO. 2016- 18.18.2 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore

DSR NO. 2016- 18.20.3 Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main : 25 mm nominal bore

DSR NO. 2016- 18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

DSR NO. 2016- 18.53.1 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

DSR NO. 2016- 18.64 Providing and fixing PTMT swivelling shower, 15 mm nominal bore, weighing not less than 40 gms

DSR NO. 2016- 18.33.1 Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation oncrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

DSR NO. 2016- 18.4 Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

DSR NO. 2016- 18.40.4 32 mm diameter pipe

DSR NO. 2016- 18.40.6 50 mm diameter pipe

DSR NO. 2016- 18.46 Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) :

DSR NO. 2016- 18.46.4 32 mm diameter pipe

DSR NO. 2016- 18.46.6 50 mm diameter pipe

DSR NO. 2016- 16.1 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

DSR NO. 2016- 16.78 Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineerin- Charge.

DSR NO. 2016- 16.78.1 With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

DSR NO. 2016- 16.69 Providing and laying at or near ground level factory made kerb stone of M- 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

DSR NO. 2016- 2.1 Trenching in ordinary soil up to a depth of 60cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling with in a lead of 50m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

DSR NO. 2016- 2.2 Supplying and stacking of good earth at site i/c royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

DSR NO. 2016- 2.3 Supplying and stacking sludge at site including royalty and carriage up to 1 km (sludge measured in stacks will be reduced by 8% for payment)

DSR NO. 2016- 2.4.1 Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm

DSR NO. 2016- 2.5 Rough dressing the trenched ground including breaking clods

DSR NO. 2016- 2.6 uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation

DSR NO. 2016- 2.7 Fine dressing the ground

DSR NO. 2016- 2.8 Spreading of sludge, dump manure or/and good earth in required thickness (Cost of sludge, dump manure or/ and good earth to be paid separately)

DSR NO. 2016- 2.9 Mixing earth and sludge or manure in proportion specified or directed by the officer-in-charge

DSR NO. 2016- 2.12 Uprooting rank vegetation and weeds by digging the area to a depth of 60cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts

DSR NO. 2016- 2.13 Preparation of beds for hedging and shrubbery by excavating 60cm deep and trenching the excavated base to a further depth of 30cm refilling the excvated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of rearth after redution by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling and directed, within a lead of 50m. lift upto 1.5m complete (cost of sludge, manure or extra earth to be paid for seperately)

DSR NO. 2016- 2.14.4 Digging holes in ordinary soil and refilling the same with the exavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reductin by 8%9 flooding with water, dressing including remocal of rubbish and surplus earth, if any with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for seperately) Holes 45cm dia and 45cm deep

DSR NO. 2016- 2.16 Providing and fixing M.S. flat iron tree guard 60 cm dia and 2 m high, above ground consisting 4 nos 25 x 6 mm, 2.25 m long and 8 nos 25 x 3 mm 2 m long verticals M.S. flats, riveted to 3 nos 25 x 6 mm M.S. flat iron rings in two halves, fixing together at site with required six numbers of 8 mm dia and 30 mm long bolts, including painting two coats with synthetic enamel paint of approved brand and manufacture over a coat of primer. One name plate of 1 mm thick M.S. sheet of size 250x100 mm shall be welded to the tree guard near the middle height and lettered CPWD / PWD/ any other approved name. The tree guard shall be suitably fixed to the ground by embedding four legs of tree guard in pits of suitable dia and to a depth of 25 cm, refilling the pits with soil and ramming, complete in all respect as per satisfaction and direction of Officer-in-charge.

DSR NO. 2016- 2.19.1 Edging with bricks laid dry length wise, including required excavation, refilling, consolidating with hand packing and spreading surplus earth neatly within a lead of 50 m : Common burnt clay F.P.S. (non modular) bricks of class designation 7.5

DSR NO. 2016- 19.19.1.1 P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. Rectangular shape 600x450mm internal dimensions

DSR NO. 2016- 19.15.1 Providing MS foot rest including fixing in manholes with 20x20x10cm cement concrete blocks 1:3:6 as per standard design. (i) with 20x20mm square bar

DSR NO. 2016- 19.32.1 Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.

DSR NO. 2016- 19.19.4.1 P/F in position pre cast RCC manhole cover and frame of required shape and of approved quality. EHD - 35 : Circular shape 560 mm internal dia

DSR NO. 2016- 23.1.1 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level. All types of soil 300 mm dia

DSR NO. 2016- 23.5 Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge

DSR NO. 2016- 23.6 Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-incharge

DSR NO. 2016- 23.7 Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

DSR NO. 2016- 23.8 Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge.

DSR NO. 2016- 23.3.2 Supplying, assembling, lowering and fixing in vertical position in bore well,unplasticized PVC medium well casing (CM) pipe of required dia,conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia

DSR NO. 2016- 23.4.2 Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 150 mm nominal size dia

DSR NO. 2016- 23.13.2 Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 150 mm dia.

DSR NO. 2016- 23.14.2 Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts f required size complete. 150 mm clamp

DSR NO. 2016- 23.15.2 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I): 150 mm dia.

DSR NO. 2016- 2-1(SOR R&B 2019-20) Cement plum Masonry with 40% plum & 60% 1:3:6 cement concrete including supply of all material, labour, T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203 of MORD Specifiction

Providing,fixing,testing and commissioning, Single Headed Stainless Steel,ISI marked oblique pattern hydrant/ landing valve with 80 NB flanged inlet & 63 mm dia instantaneous type female outlet complete with cap and chain,twist release type lug and all accessories as per IS 5290-1983 (Type-‘A’).

Non Schedule Items Make :– New Age /Omex/ ISI / Getech / Safe Fire

Providing, Fixing, Testing and Commissioning of First Aid Fire Hose Reel wall mounting swinging type complete with drum, bracket, 30 Mtr. Long high pressure hose reel tubing as per IS:44 with gun- metal shut off nozzle with 5 m orifice.The hose reel shall strictly confirm to IS:884-1985.

Non Schedule Items Make :– New Age / Omex / ISI / Getech / Safe Fire

Providing Non-percolating Flexible Hose (RRL Type- A) ISI marked (ISI : 636)63 mm dia x7.5/15 Mtr.Long complete with instantaneous type gun-metal 63 mm dia. ISI marked male & female couplings (IS : 903) bound & riveted to nose hose pipe with copper rivets and copper wire.

Non Schedule Items Make :– Jai Shree / Omex/ Fire Chief / BRG / ISI

Non Schedule Items Providing and Fixing of Hose Cabinets fabricated from 16/18 Gauge CRCA sheet with full front glass door and locking arrangements, suitable to accommodate 2 Nos.15 M long hose pipe and 1 Nos. Branch Pipe. The cabinet shall be painted with one coat of Primer and two more coats of synthetic enamel paint of provided shade.

Non Schedule Items Providing and Fixing of INTERNAL hose cabinets abricated from 16/18 Gauge CRCA sheet with full front glass door and locking arrangements, suitable to accommodate 2 Nos. 15 M long hose pipe and 1 Nos. Branch Pipe.One No Landing Valve & One No Hose Reel.The cabinet shall be painted with one coat of Primer and two more coats of synthetic enamel paint of provided shade.

Non Schedule Items Providing and fixing Stainless Steel Fire Brigade Inlet breaching head as per IS:904 Specification tested for 20 Kg/cm2 with 63 mm dia instantaneous type inlet and 150/100mm dia flanged outlet with built-in check valve for fire brigade connection to under ground tanks and fire risers including companion flanges as per table "E" including nuts,bolts & washers etc. Make :– New Age /Omex/ ISI / Getech / Safe Fire Two way

Providing and fixing of Stainless Steel 63 mm dia.Short Branch Pipe with 16 mm dia,nozzle (IS:903).

Non Schedule Items Make :– New Age /Omex/ ISI / Getech / Safe Fire

Non Schedule Items Providing, Fixing, testing & commissioning of Air Cushion Tank (Air Vessel) 200 mm dia & 1000 mm high with dished top, made of minimum 6 mm thick MS pipe/plate complete with 20 mm dia, brass air valve (ball type), 20 mm stop valve pressure gauge and all accessories as required including fixing brackets.

Non Schedule Items Providing, laying, testing and commissioning of "C" class MS Pipe conformingto IS: 1239 / IS:3589 including MS fittings like elbows, tees, flanges, tapers,nuts,bolts,gaskets etc with a coat of primer and paint

Make :– Jindal / Surya/ Prakash / Tata

Non Schedule Items 100 mm dia

Non Schedule Items 80 mm dia

Non Schedule Items 25 mm dia

Non Schedule Items Excavation and providing wrapping coating to underground ms pipe lines anticorrosive treatment with coaltar/asphaltic tape as per IS :10221, refilling the trench etc. complete of all sizes as required .

Non Schedule Items Providing, Fixing, testing & commissioning of cast iron flinged ISI marked -Non-Return Valves complete with rubber insertions, nuts, bolts and washers etc. IS:5312 of following sizes:

Make :– Zoloto / Kirloskar / Sant / Kartar / ISI

Non Schedule Items 100 mm dia

Non Schedule Items 80 mm dia

Providing, fixing, testing & commissioning of cast iron flanged IS marked Butterfly Valve class PN-1.6 complete with rubber etc.IS:780 of following sizes:

Make :– Zoloto / Kirloskar / Kartar / ISI

Non Schedule Items 100 mm dia

Non Schedule Items 80 mm dia

Providing ,fixing testing and commissioning of Flexible rubber Bellows double flanged as below.

Non Schedule Items 100 mm dia

Non Schedule Items 80 mm dia

Providing & fixing carbon steel Fire man axe with rubber insulated handle tested to 20000 volts.

Non Schedule Items Make – New Age /Omex/ G Tech / Safe Fire

Providing and fixing Carbon-di-oxide Fire Extinguishers consisting of welded M.S cylindrical body, squeeze lever discharge valve fitted with internal discharge tube. 30cms long high pressure discharge hose. Discharge nozzle,suspension bracket, confirming to IS:934 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge. (CCOE Nagpur Approved clynders)

Capacity 4.5 Kg.

Non Schedule Items Make :– Life guard /Omex/ Getech / Safex / Safe Fire

Providing and fixing of ABC type (Stored Pressure) Fire Extinguisher I.S.I marked & T.A.C.approved complete in all respect.

Non Schedule Items 4 kg. capacity

Make :– Life guard / Omex/ Getech / Safex / Safe Fire

Non Schedule Items Providing and fixing Water Co2 9 ltr Fire Extinguisher I.S.I marked & T.A.C.approved complete in all respect.

Capacity 9 Ltr.

Make :– Life guard / Omex/ Getech / Safex / Safe Fire

Providing and Fixing of self illuminated /auto glow Exit signs printed on photoluminescent sheet containing self illuminated base chemical,of appropriate size not less than 400x150mm,suspended from ceilling or fixed to the walls with accessories as riquired and as directed at site.

Non Schedule Items Make :– Mr. Lite / Lee Grand / ISI

Providing & fixing PRESSURE GAUGE 100 mm dia including making connection with m.s pipe complete in all respect.

Non Schedule Items Make :– Indfoss / ISI

Providing & fixing PRESSURE SWITCH 100 mm dia including making connection with m.s pipe complete in all respect.

Non Schedule Items Make :– H Guru / ISI

Providing, installation, testing and commissioning of Gun Metal Ball Valves of following sizes as required :

Make :– Kartar / Zoloto / Sant / ISI

Non Schedule Items 25 mm dia

Non Schedule Items Supplying, Installatoin, Testing, & Commissioning of Terrace pumps of 900 lpm @ 45 mtr head

Non Schedule Items Supply, installation, testing and commissioning of starter for terrace pumps

Supply, installation, testing and commissioning of gun matel body air release valve complete with all fitting as equired like ball vlave,holdtite,suta etc.

Non Schedule Items Make : Precious/zolto/swastik

Supply, Installation, testing and commissioning of Cast Iron body 'Y' Strainer complte with all fitting as requied like MS flange, nut bolts,washers etc.

Make : Castle/Deepak/Kartar

Non Schedule Items 100 mm

Providing and fixing Foot Valve

Non Schedule Items 100 mm dia

Non Schedule Items RCC Hole Cutting

Non Schedule Items Providing & laying of of Terrace tank 10,000 litre @ Rs.11.50 per litre

Non Schedule Items Connecting of terrace tank with existing water supply line

Fire Alarm System

Non Schedule Items Supply, installation, testing and commissioning of main fire alarm panel supply source (230AC 50 Hz and 24 V DC) 24V out put supply for detector. fault indication open, short circuit in detector line. visual indication fire, fault, open, short & system on. 2 Zone.

Make : Agni / Apollo / System sensor

Non Schedule Items Supply, installation, testing and commissioning of MS body electronic sounder ( hooter ).

Non Schedule Items Supply, installation, testing and commissioning of MS body manual call point.

Make : Agni / Apollo / System sensor

Non Schedule Items Supply, laying, testing and commissioning of 1.5Sq.mm PVC insulated copper conductor single core wire in the existing PVC conduit as required.

Make : Anchor / Pollycab / Great White / Equivalent

Non Schedule Items Supply, laying, testing and commissioning of 20mm PVC conduit along with accessories complete as required.

Make : Sidhbali / Kalinga / Equivalent

Non Schedule Items Supply, laying, testing and commissioning of 2X 12 AH Battery for panel.

Section B

DSR NO. 2016- 1.10 WGSTLPT Point wiring in PVC conduit, with modular type switch.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.

DSR NO. 2016- 1.10.2 Group B

DSR NO. 2016- 1.11 WGSTLMIDTC Twin Control point wiring in PVC conduit, with modular type switch:

Wiring for twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc as required.

DSR NO. 2016- 1.12 WGSTLPP2 Power plug wiring in PVC conduit (2x4 sq. mm)

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed mediumclass PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required..

DSR NO. 2016- 1.14 WGSTLSB Circuit/ submain wiring in PVC conduit:

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required

DSR NO. 2016- 1.14.2 2 x 2.5 sq.mm + 1x2.5 sq.mm earth wire

DSR NO. 2016- 1.14.5 2 X 10 sq. mm + 1 X 6 sq. mm earth wire

DSR NO. 2016- 1.14.8 4 X 4 sq. mm + 2 X 4 sq. mm earth wire meter

DSR NO. 2016- 1.14.9 4 X 6 sq. mm + 2 X 6 sq. mm earth wire meter

DSR NO. 2016- 1.14.10 4 X 10 sq. mm + 2 X 10 sq. mm earth wire meter

DSR NO. 2016- 1.21 PVCCON S/F PVC conduit:

Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including painting in case of surface conduit, or cuttting the wall and making good the same in case of recessed conduit as required.

DSR NO. 2016- 1.21.2 25mm

DSR NO. 2016- 1.23 PTSWEB S/F piano type switch/ socket:

Supplying and fixing following piano switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

DSR NO. 2016- 1.23.1 5/6 amps switch

DSR NO. 2016- 1.23.4 3 pin 5/6 amp socket outlet

DSR NO. 2016- 1.24 PTSWEB S/F modular type switch/ socket:

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

DSR NO. 2016- 1.24.1 5/6 amps switch

DSR NO. 2016- 1.24.4 3 pin 5/6 amp socket outlet

DSR NO. 2016- 1.25 MODFREB S/F modular type electronic fan regulator:

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

DSR NO. 2016- 1.29 LPACCPT S/F light plug point piano type accessories:

Supplying and fixing suitable size GI box with piano plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

DSR NO. 2016- 1.30 PPACCPT S/F power plug point piano type accessories:

Supplying and fixing suitable size GI box with piano plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

DSR NO. 2016- 1.31 LPACCPT S/F light plug point modular type accessories:

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

DSR NO. 2016- 1.32 PPACCPT S/F power plug point modular type accessories:

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

DSR NO. 2016- 1.33 CREB S/F ceilling rose:

Supplying and fixing 3 pin, 5 amp. ceilling rose on the existing junction box/ wooden block including connection etc. as required

DSR NO. 2016- 1.34 BRHOLD S/F brass holder:

Supplying and flxing brass batten/angle holder including connection etc. as required.

DSR NO. 2016- 1.38 Extra for fixing louvers/shutters complete with frame for a exhaust fan of all sizes.

DSR NO. 2016- 1.38Call Bell/Buzzer:

Supplying and fixing call bell/ buzzer suitable for single phase, 230 volts, complete as required.

DSR NO. 2016- 1.41 ITCFFSUR ITC fluorescent fitting directly on surface:

Installation, testing and commissioning of pre-wired, fluorescent fitting/ compact fluorescent fitting of all types, complete with all accessories and tube etc. directly on ceiling / wall, including connection with 1.5 sq.mm FR PVC insulated, copper conductor, single core cable and earthing etc. as required.

DSR NO. 2016- 1.44 ITCCFFC ITC ceiling fan:

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

DSR NO. 2016- 1.45 ITCCFFC ITC ceiling fan with cover on fan box:

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq, mm FR PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

DSR NO. 2016- 1.50 ITCEF450 ITC exhaust fan upto 450 mm sweep:

Installation of exhaust fan upto 450 mm sweep in the existingopening, including making the hole to suit the size of the above fan, making good the damage, connection, testing, commissioning etc. as required.

DSR NO. 2016- 1.5 LOUSHEF Fixing louvers/shutters for exhaust fan:

Extra for fixing louvers/shutters complete with frame for a exhaust fan of all sizes.

DSR NO. 2016- 2.3 PWTPMCBDB S/F SP MCB DB:

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

DSR NO. 2016- 2.3.3 12 way, Double door

DSR NO. 2016- 2.4 PWTPMCBDB S/F TP MCB DB:

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

DSR NO. 2016- 2.4.1 4 way (4+12) Double door

DSR NO. 2016- 2.4.2 6 way (4 + 18), Double door

DSR NO. 2016- 2.4.3 8 way (4 + 24), Double door

DSR NO. 2016- 2.5.3 12 way (4 + 36), Double door

DSR NO. 2016- 2.10 MCBC S/F 'C' Curve, SP MCB

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

DSR NO. 2016- 2.10.1 Single pole

DSR NO. 2016- 2.12 MCBTPIS S/F SP MCB isolator:

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

DSR NO. 2016- 2.12.2 63 amps

DSR NO. 2016- 2.13 MCBTPIS S/F TP MCB isolator:

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissoning etc. as required.

DSR NO. 2016- 2.13.1 40 amps

DSR NO. 2016- 2.13.2 63 amps

DSR NO. 2016- 2.15 Supplying and fixing following rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

DSR NO. 2016- 2.15.2 40 Amp.

DSR NO. 2016- 2.15.3 63 Amp.

DSR NO. 2016- 5.4 EARGIPL G.I earth plate elctrode:

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

DSR NO. 2016- 5.9 EARG125X6 S/L 25 mm x 5 mm G.I. earth strip in ground:

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Non Schedule Items CEILLING FAN

Supply of 1200 mm sweep , 5 star rated ceiling fan . (Havells catc. ref. ES NEO or equivalent) complete in all aspects as per direction of Engineer in Charge

1200 mm sweep

Non Schedule Items Supply of Metallic range exhaust fan, 300 mm sweep. (havells catc. ref. Ventil Air- DSP or equivalent),complete in all aspects as per direction of Engineer in Charge.

300 mm sweep 900 rpm

Non Schedule Items Supply of New E-Lite 20 W LED Triyca batten. A Color changing LED batten with options of 3000 K, 4000 K & 6500 K, all in one fixture. (havells catc. ref. LHEXBYPNIN1W020 or equivalent)

Non Schedule Items Supply of 7w LED Bulb for mounting on Brass Holder. (havells catc. ref. LHLDEUHEMC8R007 or equivalent)

Non Schedule Items Supply & Fixing of 1.5 ton split AC Hot & Cold type with necessary Accessoires, Cu-piping etc. complete in all respect.

Non Schedule Items Supply & fixing of main wall mounted pannel board with 1 no. incomer of 400 amp.FP MCCB (25 KA)& outgoings of 06 no. outgong of 125 amp. FP MCB & 3 no. 100 Amp. FPMCCB with suitable busbar, change over switch,ammeter, voltmeter,indicating lamps etc. complete in all respect.

DSR No. 2016-5.6 Earthing with copper earth plate 600 mmx 600mmx3mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and water pipe of 2.7 metre long etc with charcoal/coke and salt as required.

DSR No. 2016- 7.1 Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required.

DSR No. 2016- 7.1.1 Upto 35 sq. mm

DSR No. 2016- 7.1.2 Above 35 sq. mm and upto 95 sq. mm

DSR No. 2016- 7.1.4 Above 185 sq. mm and upto 400 sq. mm

Supply,of following sizes of PVC sheathed LT XLPE armoured, aluminium 1.1KV grade, as required of the following sizes.

Non Schedule Items 3.5 c x 300 sq.mm cable

Non Schedule Items 3.5 c x 70 sq.mm cable

Non Schedule Items 3.5c x 25 sq. mm cable

Non Schedule Items 4c x 16 sq. mm cable

Non Schedule Items 4c x 10 sq. mm cable

Non Schedule Items 4c x 6 sq. mm cable

Non Schedule Items Supply of 6 Mtr. Long steel tubular pole with 45 watt LED light fitted on 5 bracket including making foundation, painting of pole making connections complete in all respect.

Non Schedule Items Fixing of 6 Mtr. Long steel tubular pole with 45 watt LED light fitted on 5 bracket including making foundation, painting of pole making connections complete in all respect.

Non Schedule Items SITC of wall mounted Sub pannel board with 1 no. incomer of 63 amp.FP MCCB (25 KA)& outgoings of 04 no.2 To 32 amp. DP MCB (25 KA) MCB with suitable busbar, change over switch,ammeter, voltmeter,indicating lamps etc. complete in all respect.

Non Schedule Items Supply Installation and commissioning of 250 KVA compact sub station .

Non Schedule Items Testing at Plant of 250 KVA Compact Sub Station.

Non Schedule Items Foundation for CSS and D.G Set.

Non Schedule Items SITC of main wall mounted pannel board with 1 no. incomer of 400 amp.FP MCCB (25 KA)& outgoings of 3 no. 250 Amp. FPMCCB,2 no. 125 Amp. FPMCCB,3 no. 63 Amp. FPMCCB with suitable busbar, change over switch,ammeter, voltmeter,indicating lamps etc. complete in all respect.

Non Schedule Items Supply and Installation of Silent type Acoustic enclosure diesel Genenrating set along with having prime power rating of 125 KVA 415 Volt suitable for 50 Hz 3 Phase system complete with suitable Diesel Engine with Complete (Including GST 18%) with foundation.

NETWORKING

Non Schedule Items RJ45 IO with Face Plate

Non Schedule Items RJ11 IO with Face Plate

Non Schedule Items 24 port CAT-6 Patch panel

Non Schedule Items 30 pair MDF

Non Schedule Items 1 Mtr Patch Cord

Non Schedule Items 3 Mtr Patch Cord

Non Schedule Items Supply of 24 U rack floor rack

Non Schedule Items Supply of 6 U rack floor rack

Non Schedule Items Supply of 24 port switch L2

Non Schedule Items Epbax 42 Line extension 4 tank line 2 digital line

Non Schedule Items UPS 1 KVA Offline

Non Schedule Items UTP CAT-6 Cable Box

Non Schedule Items 4 pair telephone cable

Non Schedule Items PVC Pipe (20 mm Dia)

Non Schedule Items Installation of I/O

Non Schedule Items Fixing of 24 Port UTP CAT6 jack Panel

Non Schedule Items 30 pair mdf installation charges

Non Schedule Items Fixing of 24/12/6 U rack wallmount.

Non Schedule Items Switch installation and configuration

Non Schedule Items Epbax Installation and Configuration

Non Schedule Items Cat 6/4 pair cable lying work in existing PVC pipe

Non Schedule Items Pipe laying

Non Schedule Items Supply and Installation and Commissioning of 8 Passenger Lift (weight 544 Kg for G+3 floors) with opening of 800 mm, with required well size.1900x1900 mm complete in all aspect with requied speed and controls.

Non Schedule Items Supply and Installation and Commissioning of 8 Passenger Lift (weight 544 Kg for G+2 floors) with opening of 800 mm, with required well size.1900x1900 mm complete in all aspect with requied speed and controls.

Non Schedule Items Supply and Fixing of Solar Power Generating System 10kwp Off-GRID Complete in all respect.(10 KW)

Makin Developers Pvt. Ltd.

Yamuna Nirman

M/s HC BANSAL ENGINEERS AND CONTACTORS

Sunehari Bagh Builders Pvt. Ltd.