Upgradation of Regional Directorate office, Srinagar Phase-II

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles 10 mm to 25 mm.

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-incharge: 1:3:6 or richer mix (i/c equivalent design mix).

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and Laying of stone soling (dulyu hand packed) incl. watering dressing and ramming incl. all-inclusive leads, lifts, loading, unloading, head load if any and carriages of material fro approed source to site of work complete.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) incl. all leads. lifts, head loads and carriages of all material involved complete.

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) incl. all leads. lifts, head loads and carriages of all material involved complete.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:6 ( 1 cement : 6 coarse sand. incl. all leads. lifts, head loads and carriages of all material involved complete.

15 mm Cement plaster on the rough side of single or half brick wall of mix 1 : 6 ( 1 cement : 6 coarse sand) incl. all leads. lifts, head loads and carriages of all material involved complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm.

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2 mm thick

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately): Second class kail wood incl. all leads. lifts, head loads and carriages of all material involved complete.

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. With ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 35mm.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Clearance of Septic tank by way of Engagement of suckers for clearing, taking out all the slush, unhygienic material rom the tanks and disposal of the same beyound municipal limits complete job.

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required: One urinal basin with 5 literwhite P.V.C automatic flushing cistern.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-Charge and finished smooth. 16mm Granite Stone of approved shade.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing CP 15mm Dia wash Basin / Sink Mixer of standard design and of approved quality and make complete. Sample to be approved by Engineer-in-charge.

Providing and fixing CP Angle Valves 15mm Dia of approved brand with CP Wall Flange of approved quality and make complete incl. cutting and making good walls. Sample to be approved by Engineer-in-Charge.

Providing and fixing of CP Fitting of approved brand and manufacture two in one Bib Cock.

Providing and fixing of Stainless Steel anti cockroach type trap gratings.

Providing and fixing CP Health faucet of approved brand with connections inl. CP Wall flange etc.

Providing and fixing PVC Connections of required size and of standard quality.

Providing and fixing PVC Waste Pipe of required size and standard quality.

Providing and fixing of 600x20 mm Towek rails of approved quality incl. cost of screws and making good walls wherever necessary.

Providing and fixing CP Soap dish / Tray of approved make incl. cost of screws.

Providing and fixing 600 x 450 mm bevelled edge mirror of approved quality with 6mm marine ply wood with CP brass screws and washers.

Providing, installation, commissioning and testing 50 litre capacity Hot water Geyser of approved make including fixing with bolts and making necessary connections. Make: Venus, Racold or Hindware to be approved by the Engineer-in-Charge.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.

Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.

PN-16 pipe , 25mm OD (SDR-7.4)

External work including trenching, refilling etc.

PN-16 pipe, 40mm OD (SDR-7.4

PN-16 pipe , 32mm OD (SDR-7.4

Providing and fixing PPR Unions

PPR Union 25mm

PPR Union 32mm

PPR Union 40mm

Providing and Fixing PPR Ball valve of approved quality, High or Low presure, with plastic floats complete.

40mm dia, nominal bore

32mm dia, nominal bore

25mm dia, nominal bore

Cutting holes up to 30x30 cm in walls including making good the same: With common burnt clay (non modular) bricks.

Cutting holes up to 15x15 cm in R.C.C. floors and roofs for passing drain pipe etc. and repairing the hole after insertion of drain pipe etc. with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete so as to make it leak proof.

Providing and Fixing Sanitary PVC pipes (B-Types) of standard quality incl. fittings, cutting and making good the walls & Floor complete.

50mm dia

75mm dia

100mm dia

Floor traps

Reducer 100x 75mm

100mm doo bend / TEE

PVC Half Bend 45 degree 75mm

PVC Plain Tee 75mm

Collers

75mm Door Bend

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing 600x120x5mm glass shelf with edges round off supported on anodized aluminum angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs, etc. complete.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarsesand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4graded stone aggregate 20 mm nominal size) finished with a floatingcoat of neat cement complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Providing Retro-reflective regulatory sign board of required with and hight made out of 2mm thick aluminum sheet, face to be fully covered with highintensity encapsulated lens type retro-reflective sheeting as approved by Engineer-in-charge. Letter, symbols, borders, etc. will be as per IRC:67 with required colour scheme on the boards and with the high intensity grade A. the aluminum sheet to be riveted to M.S. frame of pipe size 75mmx4mm. The boards will be fixed to 1 No. 50x50mm square post made of M.S. pipe 75mmx4mm, welded to the frame with adequate anti-theft arrangement. Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and backside of aluminum sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as perdirections of Engineer-in-charge. with 150 mmx6mm pipes at the sides for support and frame of 75x4mm pips as per requirement at site.

Providing ad Fixing Powder Coated Hardware fittings of standard quality.

Handle 150mm

Tower Bolt 150mm

AI Drop 300 mm

AI Drop

P/F of 8mm thick laminated wooden flooring with foam incl. necessary beeding/cornices of approved quality required shade as per directions of Incharge inclusive of all carriages complete job at site complete.

Providing and fixing of wooden panelling over 12mm ply frame work including all necessary fittings & fixtures (Accessories) with necessary polishing and carriage of all materials complete as directed by Engineer-In-Charge at site complete. (imported Kail wood panelling).

Providing & Fixing of Wall Paper of Superior Quality on walls of approved Design incl cost of Labour, Adhesive, Leads and lifts, Head load with all carraiges upto site of work all complete.

Providing and fixing of PVC panelling 10" wide 6mm thick of required shade and design of approved brand including all necessary secrews backing of 19mm thick Water proof-plyboard battens design approved by engineer incharge / consultants / client.complete job.

Providing anf fixing wall hangings cabinets (600 mm high 400 mm deep) frame work of first class Badloo wood shutter of 19 mm thick ply board along with 0.80 mm dulmica of approved shade inclusive of all haerdware fittings like towerbolts, handles magnet catches inside R shelves should be 19mmply board 400 mm deep complete in all respects as designed and desired by engineer incharge.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work.

Renewing glass panes, with putty and nails wherever necessary including raking out old putty : Float glass panes of thickness 4.0 mm(weight not less than 10kg/sqm).

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 meters lead of : G.S. Sheet.

Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal / vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gram/m2.

Providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J. or L hooks, bolts and nuts 8mm dia G.I. limpet and bitumen washers complete. 0.63 mm thick with zinc coating not less than 275 gram/m2.

Providing valleys of 90cm wide overall in plain G.S. sheets fixed with polymer coated J. or L. hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete. 1.00 mm thick with zinc coating not less than 275 gram/m2.

Wiring for light point/fan point/exhaust fan point/ call bell point with 2X 1.5 sq.mm FRLS PVC insulated copper conductor (Havell/Polycab/ Fenolex/Anchor/eq. standard make as desired by engineer incharge) single core cable in surface / recessed medium class PVC conduit, with modular switch (Legrand Mylinc/SSK NV/schneider Livia /ABB Tvisha make.), modular plate, suitable Gl box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm + 1X 4 sq. mm earth wire, FRLS PVC insulated copper conductor (Havell/Polycab/ Fenolex/Anchor/equivalent as directed by engineer incharge.) single core cable in surface/recessed medium class PVC conduit.

Supplying and fixing suitable size Gi box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, modular plate, suitable Gl box, connections etc. as required. Modular Switch & Socket:-( Legrand Mylinc/SSK NV/schneider Leiva /ABB Tvisha make make.

Wiring for lighting circuits/6-10 amp power plugwith 2X2.5 sq. mm FRLS PVC insulated copper conductor (Havell/Polycab/Fenolex/Anchor/equivalent as directed by engineer incharge.) single core cable in surface/recessed medium class PVC conduit alongwith 1. No. 2.5 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings). Modular Switch & Socket:- (Anchor roma plus/Legrand Mylinc/SSK NV/schneider Livia/ABB Tvisha make).

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Wiring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC Insulated copper conductor (Havell/Polycab/Fenolex/Anchor/equivalent as directed by engineer incharge.), single core cable in surface/ recessed medium class PVC conduit as required.

2x1.5 sq.mm + 1x1.5sq.mm earth wire.

2x6 sq.mm + 1x6 sq.mm earth wire.

2x16 sq.mm + 1x6 sq.mm earth wire.

Supplying and Fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supply installation testing and commissioning of 18 W LED Surface/recess, square or round Mounted light luminary fitting shape with minimum system lumen efficacy of 100 lm/W with Pressure Die cast Aluminium body and Heat Sink and P.F.>0.95, THD 10%, CCT 5700K, CRI 80. The LED with Useful life of 50000 Hrs at L70.. The Input voltage range shall be 150V to 270V. The Fixture should have in-built Surge Protection of 2kV. Certification:- LM79 & LM80 test report should be from govt approved in-house NABL lab/ government of India. The job includes AMC (reckoned from date of successful commissioning) of lighting fixtures for a period of Two years, which includes replacement of fixtures of Philips/Helonix/Havell/Wipro/Eq. standard make as directed by the engineer incharge.

S/F testing and comm. Of MCB's 10 K of the below mentioned capacities in sub main controls legrand C curve/Schinider/L&T /equivalent make as directed by engineer incharge.

6-32 Amp SP MCB

40-63 Amp DP MCB

Supply installation testing and comm. Of 200-250mm sweep exhaust fan Shutter type of havell /Bajaj/Crompton/equivalent make as directed by engineer incharge, including making of space in wall/ window as per site requirement and necessary connections.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, ceiling fan with 3 No. Aluminium blades, 30 cm long down rod, 2nos. canoples, shackle kit, Power Factor not less than 0.9, Service Value Including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, and including iron hook complete. USHA /Havells/Crompton make, sample to be approved before installation...

Supply and fixing of 6 amp/250 V A.C fan dimmer step type 2 module with cover plate Anchor Roma urban/SSK NV/ equivalent make as directed by engineer incharge.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator), (Indo Asian/legrand/Shinider/ABB make) 4 way (4+12), Double door.

Supply fixing testing and comm. Of backlite holder/batten holder/angle holder/celling rose SSK/Anchor make incl. PVC Block.