Construction of Lecture Hall Home Guard Battalion Training Centre at Sarabai Tehsil Bhunter Distt.Kullu HP

Amount

Excavation in foundation, trenche etc. in earth work in all kinds of soil such as pick work, jumper work, blasting work in soft and hard rock, conglomerated rock or saturated soil and its intermediate classification of soil, chieseling work and wedging out rock (where blasting is prohibited) and pumping or bailing out watering/ dewatering up to any lift, stacking the excavated soil up to any lead from the edge of excavation and then returing the stacked soil in 15 centimetre layer when required into plinth, sides of foundation etcetra. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in all leads and lift and carriage of materials in all respect as per direction of Engineer-in-charge.

Providing form work with steel plates 3.15mm. (Three point fifteen milimetre) thick welded with angle iron in frame 30x30x5mm.(thirty into thirty into five milimetre) so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs.(four metre) and removal of the same for insitu-reinforced concrete & plain concrete work in: (a) Foundation, footings basis of columns etc. and mass concrete.including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like. Floors etc.upto 200mm. (two hundred milimetre) In thickness.including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Columns, pillars, posts and struts Square, rectangular or polygonal in plan.including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Stair cases with sloping or stepped soffits excluding landing.including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers,bressumers and lintels not exceeding 1 Mtr. (one metre) in depth in all heights from floor.including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Edges of slabs and breaks in floors and walls: under 20 cm. (twenty centimetre) wide.including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and laying cement concrete 1:4:8 (one cement: four sand:eight graded stone aggregate 40mm (forty milimetre nominal size) and curing complete excluding cost of form work in: Foundation and plinth:including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and laying cement concrete 1:6:12 (one cement:six sand : twelve graded stone aggregate 40 mm (forty milimetre nominal size) and curing complete excluding cost of centring and shuttering in: Foundation and plinth:including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and laying upto floor two level cement concrete 1:2:4 (one cement : two Sand : four graded stone aggregate 20mm (twenty milimetre nominal size) and curing complete including form work in : Mouldings as in cornices, window sills etc. Exceeding 15cm.(fifteen centimetre) in girth.including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and laying cement concrete work 1:2:4 (one Cement: two Sand:four graded stone aggregate 20 mm (twenty milimetre nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in :Suspended Floor roofs, landing and shelves and their support balconies,beams, girders, bressumers and contilever upto floor twolevel including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and laying cement concrete 1:1.5:3 (one cement :one point five sand :three graded stone aggregate 20mm.(twenty milimetre nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in: (a) Foundation footings bases of columns and the like and mass concrete. including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Suspended floors roofs, landings and shelves and their supports, balconies, beams, girders, bressumers and cantilevers upto floor two level. including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Stair cases (except spiral stair case) excluding landing but including preparing of the surface and finishing of nosing upto floor two level. including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Column, pillars, posts and struts upto floor two level :including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing mild steel/Tor steel reinforcement for R.C.C. (rainforced cement concrete) work including bending, binding and placing in position complete upto floor two level : Tor Steel including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Brick work using common burnt clay building bricks in foundation and plinth in :-Cement Mortar 1:6 (one Cement : six Sand) Second Class Bricks including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement :six sand : twelve graded stone aggregate 20mm (twenty milimetre nominal size) at plinth level in Cement Mortar 1:6(one cement:six sand) including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Stone filling behind retaining walls : under floor including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Precast concrete block masonry (including quion blocks,jamb blocks, closer etc.) with solid concrete blocks of approved size made of cement concrete 1:3:6 (one cement:three sand:six graded stone aggregate 40mm (forty milimetre) and down gauge foundation and plinth upto floor level two in :- Cement Mortar 1:6 (one cement: six sand). including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Precast concrete block masonry in partition walls 10 cm.(Ten centimetre) thick with solid block of approved size including quion blocks, jamb blocks, closer etc. made of cement concrete 1:3:6 (one cement:three sand:six graded stone aggregate 40mm (forty milimetre) and down gauge in :- Cement Mortar 1:6 (one cement: six sand) including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing woodwork in frames of doors,windows,clerestory,windows and other frames wrought,framed and fixed in position. 2nd class deodar wood.including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws.40 mm (forty milimetre) thick 2nd class deodar wood. including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing 35 mm (thirty five milimetre) thick Decorative flush door with peep hole Phenal bonded including black enanelled M.S bult hinges. including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm (zero point fifty six milimetre) for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws. 40 mm (forty milimetre) thick 2nd class deodar wood including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing 40x3 mm (forty into three milimetre) flat iron hold fast 40cm. (forty centimetre) Long including fixing to frame with 10mm (ten milimetre) diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm (thirty into ten into fifteen centimetre. 1:3:6 ( one cement : three sand: six graded stone aggregate 20mm (twenty milimetre nominal size). including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws. Plain grill. including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete. (a) 300x16mm (three hundred into sixteen milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

250x16 mm (two hundred fifty into sixteen milimetre) including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete. (a) 250x10mm (two hundred fifty into ten milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

150 x 10mm (one hundred fifty into ten milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete. (a) 125 mm (one hundred twenty five milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

100 mm (one hundred milimetre) including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing 12 mm (twelve milimetre) thick prelaminated board both side bwp phenol bonded exterior/interior grade panalled shutters with frame of first class deodar wood for doors including bright finished/black enamelled iron butt hinges with necessary screws 40 mm (forty milimetre) thick frame.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing 6mm (six milimetre) thick fibre cemat board ceiling with bult jointed and rails (frame work and cover fillets to be measure and paid saparately. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing 6mm (six milimetre) digital ceremic tiles in skirting riser of steps and dado 12 mm (twelve milimetre) thick cement mortar 1:3 (one cement: three sand) and juinting with cement slurry. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing granite stone 20 mm (twenty milimetre) thick in riser of step skirting dado and pillar laid on 12 mm (twelve milimetre) (average) thick cement mortar 1:3 (one cement: three sand) and jointed with grey cement slurry mixed with pigmat to match the shade of slabs including rubbing and polishing. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing 10mm (ten milimetre) thick anti skid water proof stain and impect resistent heavy duty vetrified tiles Nitco or equivalant 600x600mmx10mm (six hundred into six hundred into ten milimetre) manufactured of approved shade and colour in flooring, treads of steps and landings laid over 12mm (twelve milimetre) thick cement mortar 1:3 (one cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and laying Duro stone vetrified tiles (300mmx300mmx8mm) (three hundred milimetre into three hundred milimere into eight milimetre in grey/coloured of required shade in skirting risers of steps and dados on 12mm (twelve milimetre) thick cement mortar 1:3 (one cement : three sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and laying heavy duty precast cement conrete inter locking paver blocks vibro compacted upto M- 50 (fifty) grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (one cement : four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Subbase concrete floor to be paid for saparataly 60mm (sixty milimetre) thick inter locking blocks including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing 0.60mm (zero point sixty milimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 (twenty) microns over 5 (five) microns primer coating to back coat of polyster of 5 (five) microns over 5 (five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six milimetre) dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge.including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing ridges or hips 60 cm (sixty centimetre) overall with 0.60mm thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 (five) microns over 5 (five) microns primer coating i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm (six milimetre) dia & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer in Charges.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing M.S. BP Sheet 1.66 mm (one point sixty six milimetre) to 2mm (two milimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing flushing 38cm (thirty eight centimetre) overall with 0.60mm (zero point sixty milimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 (twenty) microns over 5 microns primer coating + back coat of polyster of 5 (five) microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six milimetre) dia meter & prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer-in-Charge.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting ,fixing in position and applying a priming coat of red lead paint. (a) In beams joists channels ,angles , tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

In gratings framed guard bars,ladders,railling,brackets and similar works.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Painting two coats(excluding priming coat on new concrete masonry/plaster surfaces with readymixed paint brushing for use on floors to give an even shade including cleaning the surface of all dirt,dust and other foreign matter and sand papering as required with:-- White paint including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Painting two coats (excluding priming coat)on new steel and other metal surface under coat with ready mixed paint brusing to give an even shade including cleaning the surface all dirt,dust and other foreign matter :-- With white readymixed paint including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting.Readymixed paint brushing wood primer pink. including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Painting two coats(excluding coat) on new wood and wood based surface with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matter,sand papering & stoping With enamel paint other than white including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

6mm (six milimetre) Cement plaster to ceiling In Cement mortar 1:3 (one Cement:three Sand) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

20mm (twenty milimetre) Cement plaster in single coat on rough side of brick/stone masonry for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty milimetre) in girth and finished even and smooth. Cement Mortar 1:6 (one Cement :six sand). including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

15mm (fifteen milimetre) cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm (eighty milimetre) in girth and finished even and smooth. Cement mortar 1:4 (one cement:four sand). including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete/masonry/plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Applying one coat of Acrylic Washable emulsion Spectrum quartz king or equivalent finish for interior painting with brushes plain smooth finish composed of acrylic polymere in emulsion inorganic/ special pigment siliceous aggregate anti fungicides anti-rusting & foaming in two coat i/c necessary putty to give smooth even surface, sand papered smooth complete. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing plinth protection 50 mm (fifty milimetre) thick in cement concrete 1:3:6 (one Cement : three Sand : six Graded stone aggregated 20 mm (twenty milimetre nominal size) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (seventy five milimetre) thick (unconsolidated) bed dry brick/stone aggregated 40 mm (forty milimetre) nominal size with rammed and consolidated and grouted with fine sand including preparation of ground. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall.15x22 cm (fifteen into twenty two centimetre) in cement mortar 1:6 (one Cement : six Sand) and inside plastring with cement plaster 1:3 (one Cement:three Sand) including earth work and laying 10 cm (ten centimetre) cement concrete in 1:5:10 (one Cement : five Sand : ten graded stone aggregate) of 40 mm (forty milimetre nominal size) and 7.5 cm (seven point five centimetre) cement concrete 1:2:4 (one Cement : two Sand : four Graded stone aggregate of 20 mm (twenty milimetre nominal size) and finished with a floating coat of neat cement complete as per standard design.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg (four point five kilogramme) /sqm including filling the joints with approved adhesive complete.(a) 150 mm (one hundred fifty milimetre) dia pipes including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete (i) PVC Plain bend 150mm (one hundred fifty milimetre) dia.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

PVC shoe 150 mm (one hundred fifty milimetre) dia including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing viterious china wash down water closet squatting pan indian type W.C pan) size 580 mm (five hundred eighty milimetre) (earth work bed concrete Foot rest and trap to be measured and paid separetely orissa Pattern PAN No. 20004.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing viterious china bowl pattern urinal including connection the urinal with waste pipe by measory of white lead mixed with chopped hump (waste pipe to be measured and paid separetely Flat back Type of size 430mm into 260 mm into 350 mm. (four hundred thirty milimetre into two hundred sixty milimetre into three hundred fifty milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing viterous china wash basin with single hole for pillar tap with C.I or M.S brackets painted white including cutting holes and making good the same fitting Flat back 550 into 400 mm. (five hundred fifty into four hundred milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing C.P brass waste for wash basin and sink 32 mm (thirty two milimetre) dia. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing 600mm x450mm (six hundred milimetre into four hundred fifty milimetre) bevelled edge mirror of superior glass mounted on 6 mm (six milimetre) thick A.C sheet or ply wood sheet and fixed to wooden plugs with C.P brass screws including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing C.P brass towel rail complete with C.P brass brackets fixed to wooden plugs with C.P brass secreen 600mm x20mm. (six hundred milimetre into twenty milimetre) including hauling/ carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing chromium plated brass soap dish with C.P brass brackets fixed to wooden cleats with C.P brass screws.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing C.P brass bib tap with capstern head 15 mm (fifteen milimetre) dia. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing C.P brass Pillar tap 15 mm (fifteen milimetre) dia. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing C.P brass angle valve 15 mm (fifteen milimetre) without nuts and pipe. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PVC connection with brass union 15 mm (fifteen milimetre) nominal bore 450 mm (four hundred fifty milimetre) length. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing brass full way valve wih wheel 15 mm (fifteen milimetre) nominal bore. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing plytheline Alumimium -polyethylene (PE-AL-DE) composit pressure pipe U.V stablized, with carbon black comforming to IS 15450-2004 water supply including clamps one metre spacing cutting and fixing and making good the wall. Etc. but excluding the cost fitting (internal work) pipe exposed on wall. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing composit end seal compression fitting as per IS 15450-2004 for cold water supply e.g tees elbows reducer connector couple and clampes with jointing, testing and fitting complete including cutting and making good the walls etc. (a) equal teas 1620.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Female branch tee 1620x1620x20 mm (one thousand six hundred twenty into one thousand six hundred twenty into twenty milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Femle elbow 1620x15mm (one thousand six hundred twenty into ifteen milimetre) thread including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Male thread connector 1620x15mm (one thousand six hundred twenty into fifteen milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Female thread connector 1620x15mm (one thousand six hundred twenty into fifteen milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Coupler 1620. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PVC water storge tank ISI 12701 marked G.I inlet and out let connection 15 mm (fifteen milimetre) nominal bore ball valve and Mosquito proof PVC cover with locking arrangement nut including hositing up to all height above ground level. 2000 (two thousand) litre net capacity. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PVC floor trap ISI marked of self cleaining design including fixing with approved adhesive cost of cutting and making good the wall and floors etc complete. 110mmx90mm. (one hundred ten milimetre into ninety miimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing high pressure PVC spigot and socket waste and ventilating pipe ISI marked including fixing with approved adhesive etc. complete. (a) 110 mm (one hundred ten milimetre) dia. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

150 mm dia. (one hundred fifty milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providng and fixing PVC single equal branch with oval access door ISI marked insertion rubber washer 3mm (three milimetre) thick bolts and nuts complete including fixing with approved adhesive complete. (a) 110mm (one hundred ten milimetre) dia. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

150 mm (one hundred fifty milimetre) dia. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PVC single equal branch plain ISI marked including fixing with approved adhesive etc complete 110 mm (one hundred ten milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PVC collors ISI marked including fixing with approved adhesive etc complete. (a) 110 mm (one hundred ten milimetre) dia. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

150 mm (one hundred fifty milimetre) dia. including Carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc complete. (a) 110 mm (one hundred ten milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

150 mm (one hundred fifty milimetre) dia. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PVC clamps ISI marked, of approved design with steel secrew and rowal plugs etc complete. (a) 110 mm. (one hundred ten milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

150 mm dia. (one hundred fifty milimetre) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PVC 'P' or 'S' trap for water closet (squatting pan) ISI marked, inclding jointing the trap with the pan and PVC pipe with approved adhesive etc complete. 110 mm (one hundred ten milimetre) dia. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PVC reducer ISI marked including jointing with approved adhesive etc complete. 150x110 mm (one hundred fifty into one hundred ten milimetre) dia. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PTMT coloured/white high denisity polys thylene poly propyiene 10 (ten) litre capacity (Full Flush) Europen standard control low level flushing cistern with fitting with a pair of bracket with fitting such as lead valve sypnon 15 mm (fifteen milimetre) nominal size PVC ball valve with polythene float with push buttan coupling for connection with in let out let and over flow pipe 40 mm (forty milimetre) dia CP flush bend including cutting holes in walls, and making good the same and connecting the flush bend with cistern and closet over flow pipe to be measured and paid saparetaly.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PTMT coloured/white automatic flushing cistern with apair of PVC/C.I or M.S brackets complete with fitting including PVC syphnonic appratus mosquito proff lid. PVC union and coupling for connection with inlet out let and overflow pipes including cutting holes and making good the same (over flow pipe to be measured and paid for separetely 5 (five) litre Net capacity. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing PTMT waste coupling of approved quatity and colour (a) 32 mm (thirty two milimetre) nominal bore. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

40 mm (forty milimetre) nominal bore.including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing 100 mm (one hundred milimetre) dia Chromium plated grating of superior quality for floor gully or Nahani Trap. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and fixing store ware gully trap grade 'A' complete with C.I grating C.R masonry in cement mortar 1:6 (one cement : six sand) chamber and water tight C.I cover with frame of 300 mm x 300mm (three hundred into three milimetre) size inside the weight of cover to be not less than 4.53 kg. (four point fifty three kilogramme) and frame not less then 2.78 kg (two point seventy eight kilogramme). square mouth type 100mm x100mm (one hundred milimetre into one hundred milimetre) size P type. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Constructing man hole with R.C.C top slab 1:2:4 mix (one cement : two sand: four graded stone aggregate 20mm (twenty milimetre nominal size) foundation concrete 1:4:8 (one cement: four sand: eight graded stone aggregate 40mm nominal size) inside plastering 15 mm thick cement mortar 1:3 (one cement: three sand) finished with a floating coat of neat cement and making channels in concrete 1:2:4 (one cement: two sand: four graded. stone aggreate 20 mm (twenty milimetre nominal size) finished smooth complete including curing and testing. inside size 800mm x800mm x500mm (eight hundred milimetre into eight hundred milimetre into five hundred milimetre) deep including C.I cover with frame (light duty single seal pattern-I) 455mm x610 mm (four hundred fifty five milimetre into six hundred ten milimetre) internal dimension total weight to cover and frame to be not less then 38 kg (thirty eight milimetre) weight of cover 23 kg (twenty three kilogramme) and weight of frame 15 kg) with 200 thick wall, of brick masonry using comon burnt clay building bricks in cement mortar 1:3 (one cement : three sand) including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

Providing and laying in trenches Galvanized mild steel tube (Medium grade) tube fittings (earth work in tranches to be measured and paid saparetely. including carriage of all labour equipements and materials to various locations through all modes of transportations in all leads and lifts to the entire satisfaction as per direction of Engineer-in-Charge.

RANDHIR JAMWAL

kotkandiconstructionpvt.ltd.

Yash Pal