Construction of 1 No Type -V Quarter for Superintending Engineer Residence at Dehra Distt Kangra H.P SH Construction of Building portion including water supply and sanitary installation Rain Harvesting system and septic tank and soak pit

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains of soil such as pick work, jumper work, pick jumper work, blasting work, jumper blasting work, soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting work is prohibited, chiseling or any other mixed variety of soil, including shoring, strutting or bailing out water upto any depth or any height quantum of water including de-watering removal of slush and stacking the serviceable and un-serviceable material clear from the edge of excavation as per direction of Engineer-in-Charge and returning the stacked soil in 15cm (Fifteen centimeter) layers, when required into plinths, sides of foundation etcetera consolidating each deposited layer by ramming, watering and then disposing of all excavated earth including carriage of material within all leads, lifts and other incidentals as per approved drawing, design and as directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Stone filling in plinth with approved quality under floor including watering, ramming, consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Foundation footings, bases of columns and mass concrete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings including curved surfaces where ever required as per Architectural drawing, design and specifications and the like floor etcetera including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in beams cantilevers girders lintels window sills, cornices, arches corbelling including curved surfaces where ever required sides and soffits of beams haunchings cantilevers bressumers and lintels upto all depths including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depths of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in columns pillar posts and struts square rectangular polygonal in plan including mouldings, cornices etcetera complete as per Architectural drawing, design and specifications including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in Stair cases (except spiral stair cases) with slopping or stepped soffits excluding landings, but including preparing of top surfaces and finishing of nosing upto all floor levels as per specifications, approved drawing, design including carriage of material within all heights leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm(Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in vertical surface such as walls (any thickness) partitions and the like including attached, pilasters, buttresses, plinth and string courses and the like including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced concrete and plain concrete work in Edges of slab and breaks in floors and walls under any thickness including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in Weather shade, Chajjas, corbels etcetera, including edges and curing complete, excluding the cost of reinforcement complete, as per HPPWD specifications or as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, toll tax or any taxes imposed by the Government.

Providing form work with steel plates 3.15mm (Three point one five millimeters) thick, welded with angle iron in frame 30x30x5mm (Thirty into Thirty into Five millimeters) so as to give a fair finish including centering, shuttering strutting and propping etc, with wooden battens and ballies, height of propping and centering in all heights. below supporting floor to ceiling and removal of the same for in situ reinforced concrete and plain concrete work in Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like complete, as per HPPWD specifications or as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, toll tax or any taxes imposed by the Government.

Providing and laying in position cement concrete 1:4:8 (One cement isto four coarse sand isto eight graded stone aggregate 20mm (Twenty millimetre) nominal size mechanically mixed and vibrated of specified grade excluding the cost of centering and shuttering, All work up to all floor level including carriage of materials in all leads and lift as per direction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying damp proof course 50mm (Fifteen millimeters) thick with cement concrete 1:2:4 (one cement isto two sand isto four graded crushed stone aggregate 12.5mm (Twelve decimal five millimeter) nominal size) and curing complete including cost of form work as required at site or as directed by the Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Royality, Malkhana, Octroi, Toll Tax Sales tax,GST or any other taxes imposed by the Government.

Applying a coat of hot bitumen (mexphalt 80/100 (eighty/hundred) or equivalent) using 1.70 Kgs. (one decimal seven zero kilogramme) per square meter on damp proof course after cleaning the surface with a piece of cloth lightly soaked in kerosene oil complete including carriage of materials within all leads, lifts and other incidental and as per the direction of Engineer-in-Charge. The rate inclusive of Malkhana, Octroi, Toll Tax Sales tax, GST or any other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated reinforced cement concrete work Grade M-20 (M-Twenty) design mix to obtain the minimum compressive strength of 20 N/mm2 (twenty newton) per square millimetre with cement contents not less than 330 kg (three hundred thirty) Killogram per cubic metre and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in foundation, footings, bases of columns etcetera and the like mass concrete complete as per HPPWD specifications approved drawings, design and as directed by the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Malkhana, Royality, Octroi, GST, toll tax, sale tax or any other taxes imposed by the Government.

Providing and laying in position machine batched and machine mixed cement concrete work of grade M-20 (M-Twenty) design mix to obtain the minimum compressive strength of 20N/mm2 (Twenty niewton per square millimetre) with cement contents not less than @ 320 kg/cum (at the rate Three hundred twenty kilogram per cubic metre) or as per approved design mix. All works above plinth level upto all floor level to give a smooth surfaces machanically mixed and vibrated including curing complete and pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing tor steel reinforcement of Tata/Sail for Reinforced Cement Concrete work including straightening, cutting, bending, placing in position and binding all complete upto all floor level Thermo-Mechanically Treated bars of grade Fe-500D or more etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Applying cement slurry on Reinforcement Cement concrete slab or cement concrete work using 2.75 kgs. (Two point seventy five Kilogram) of cement per square meter of floor area before laying cement concrete flooring including roughening, cleaning of the concrete surfaces complete as per HPPWD specifications excluding cost of centring and shuttering including carriage in all leads,lifts and as per the direction of Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (One cement isto Six coarse sand) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level Cement mortar 1:4 (One cement isto Four coarse sand) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, GST and any other taxes imposed by the Government.

Second Class Brick work using common burnt clay building bricks in Super structure above plinth level upto all floor levels in cement mortar 1:4 (one cement isto four sand) and curing complete as per approved drawing, design, specification and as per direction and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing Single rebate angle iron door,window,clerestory window frame manufactured from steel iron section of 40x40x4mm, (Forty into forty into four millimetre) thickness and MS Flat 50x4mm in combination welding together to making one frame including hinges jamb,lock jamb,beed and if required angle thrashold of mild steel angle 50x25mm (Fifty into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5mm (Two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after preteatment of the surface complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S. channels Frames for doors, windows, frames manufactured from ISMC 75mmx40mm (Seventy five millimetre into forty millimetre) with M.S. flat 75mmx4mm (Seventy five millimetre into four millimetre) in combination as per drawing and design including hinges, jamb, lock jamb beed and if required thrashold including thrashold of M.S. angles means lugs, with split and tails to each jamb including iron butt hinges 2.5mm (Two point five millimetre) thick with a provision of locking arrangement and shock observers as specified and applying a coat of approved steel primer after pre-treatment of the surface complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 40mm (Forty millimetre) thick first class deodar wood panelled shutters for doors having 12mm (Twelve millimetre) thick phenol bonded both side prelaminated particle board ISI marked IS No. 12823 of approved shade infill panel of Action tessa /century /Kitlam including M.S. pressed butt hinges bright finished of required size with necessary screws complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators shutters side /top /centre hung , with beading and all members such as F7D, F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other fittings, complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing fly proof stainless steel wire mesh shutters having stainless steel 32 gauge fly mesh of 304 grade with 144 holes per square inch of 0.5mm (Zero point five millimetre) dia wire and 1.4mm (One point four millimetre) aperture on both sides in existing steel shutters complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing Glazing with glass panes of 5mm ( Five milimetre) thick plain glass weight not less than 12.50Kg/M2 (twelve point five zero Kilogramme per square metre) of Modiguard / Saint Gobian for shutters with wooden beading and nails complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing Glazing with frosted glass panes 4mm (Four milimetre) thick weight not less than 10.00Kg/M2 (Ten Kilogramme per square metre) of Modiguard / Saint gobain for shutters with wooden fillets and nails complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing plain M.S. grills of required patterns in steel frames of window etc. with M.S grill made of 10mm (ten millimeter) M.S square bar welded to 6mmx12mm (Six millimeter into twelve millimeter) M.S. flat, round bars bolts and nuts or screws complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including of Toll Tax Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing angle iron frames for SDB & Cupboard of mild steel Angle sections of size 25x25x5 mm, (Twenty five into twenty five into five millimetre) joints mitred and welded by angle iron 25x25x5mm (Twenty five into twenty five into five millimetre) or 25x5mm (Twenty five into five millimetre) flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per HPPWD specifications or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including of Toll Tax Sales tax, GST or any other taxes imposed by the Government.

Providing and fixing the complete box of cup board sahll be made of 19mm (Twenty millimetre) thick water proof ply board BWP grade shutter with Had wood edging of Uniply / Green ply/ Century ply / Kitply / Dura ply / Marino ISI marked including shelves.Back side of board shall have 6 to 8 mm (Six to eight millimetre) thick water proof ply all the cut portion of board shall have 6 mm (Six millimetre) thick hard wood edging. The shutter from all side shall be finished with 1mm thick lamination ISI Marked of approved shade of Century / Greenlam /Action Tesa and 19 mm (Nineteen millimetre) thick water proof Ply board of Uniply / Green ply/ Century ply / Kitply / Dura ply / Marino including hinges, PTMT handle in wood colour of Prayag Polymers,knob megnatic catcher complete as per specifications, approved drawing, design, as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing cup-board shutter magnic catcher with necessary screws etcetera complete as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 65x35mm (Sixty five into Thirty five millimetres) special quality bright finished brass cup-board locks or ward robe locks with six levers including necessary screws etcetra complete (Indian make of approved quality) as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 19mm (Nineteen millimetre) thick water proof Ply board BWP grade shutter of century ply /Kitply /Marino (ISI marked) with 6mm (Six millimetre) thick hard wood edging all round and PGI sheet linning inside for FF/SDB including fixing with nickel plated piano hinges with screws etcetera complete as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing Stainless Steel curtain rail with rollers stop ends and brackets in pelmets with curtain rod 25mm (Twenty five millimetre) dia and brackets complete as per the entire satisfaction and direction of the Engineer-In-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkana, sale tax, toll tax, GST and all type of other taxes imposed by the Government.

Providing and fixing 300x16 mm (three hundred into sixteen millimeters) aluminum Matt finished sliding door bolts, make of PILOT/Sheel or equivalent anodized transparent or dyed to required colour and shade with necessary bolts, nuts and screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 250x10mm (Two hundred fifty into ten millimeters) aluminum Matt finished tower bolts (Barrel type) make of pilot/sheel or equivalent anodized transparent or dyed to required colour and shade with screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 150x10mm (One hundred fifty into ten millimeters) aluminum Matt finished tower bolts (Barrel type) make of pilot/sheel or equivalent anodized transparent or dyed to required colour and shade with screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Octroi, Toll tax, GST or any taxes imposed by the Government.

Providing and fixing 125mm (one hundred twenty five millimeters) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (one hundred millimeters) aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Providing and fixing Aluminum oxidized PILOT/ Sheel or equivalant oxidized 250mm (Two hundred fifty millimetre) size hooks and eyes complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Providing and fixing Aluminum oxidized Hydraulical door closer complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetre) bright finished brass floor door stopper with rubber cushion screws etc. to suit shutter thickness complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Providing and laying 30x30cm (Thirty into thirty centimetre) automatic hydraulically compressed and polished terrazzo tiles ISI marked number IS-1237 of NTC make in 70% (Seventy percent) white and 30% (Thirty percent) grey cement having 55% (Fifty five percent) in white chips and 15% (Fifteen percent) each yellow dark, green and Maroon chips of specified sizes and O, B and 2B ) or its equivalent with 7.5cm (Seven point five centimetre) wide Baroda green marble band laid in floor, treads of steps and landing on a bed of 25mm (twenty five millimetre) average thickness of cement mortar 1:6 (one cement isto six sand) and jointed with neat cement slurry mixed with pigment to match the shade of tiles (wherever required) including rubbing and polising complete with approved shade tiles upto all floor levels as per HPPWD specification, approved drawing, design or as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Malkhana, Royality, Octroi, GST, toll tax. sale tax or any other taxes imposed by the Government.

Providing and Laying automatic hydraulically compressed and polished pre-cast terrazzo tiles 30x30cm ISI marked 1237, in 70% white & 30% grey cement having 55% white chips and 15% each yellow dark green mehroom chips. The size of chips shall be O, B & 2B or its equivalent in skirting, risers of steps and dado and to be laid on bed of 12mm average thickness of cement mortar 1:3 jointed with cement slurry mixed with pigment to match the shade of tiles (Wherever required) including rubbing and polishing complete with approved shade tiles upto all floor levels as per HPPWD specification, approved drawing, design or as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Malkhana, Royality, Octroi, GST, toll tax. sale tax or any other taxes imposed by the Government.

Providing and laying 25mm (Twenty five millimetre) thick Mirror polished Kota stone slab 55x55cm (fifty five into fifty five centimetre) mirror polished with 7.5cm (seven point five centimetre) wide Jaislmer yellow band in flooring laid over 20mm (twenty millimetre) thick base of cement mortar 1:4 (one cement isto four sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing nosing and moulding complete upto all floor levels as per HPPWD specifications approved drawig, design or as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Malkhana, Royality, Octroi, GST, toll tax, sale tax or any other taxes imposed by the Government.

Providing and fixing 20mm (Twenty millimeters) thick Kota stone slabs in risers of steps, skirting, dado and pillars laid on 12mm (Twelve millimetre) (average) thick cement mortar 1:3 (One cement isto three coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Providing and laying 300x300mm (Three hundred into three hundred millimetre) antiskid Ceramic Tiles of Nitco/ Kajaria/ Johnson /AGL / Somany/ Orient Bell in flooring laid over 20mm (Twenty millimeters) thick Cement mortar 1:4 (One cement isto four coarse sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete upto all floor level in all heights as per approved specifications, drawing and design and entire carriage of material with in all leads, lifts and other incidentals, as per the direction and entire satisfaction of Engineer-in- Charge. Rate is inclusive of toll tax, GST and any other taxes imposed by the Government.

Providing and laying 300x200mm (Three hundred into two hundred millimetre) white glazed tile/ glazed tiles of Restile/ Nitco/Kajaria/AGL /Simpolo/Somany /Johnson as per approved shade and design of the office (thickness to be specified by the manufacturer) in skirting, riser and steps with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (One cement isto four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etcetera, complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 18mm (Eighteen millimetre) thick Baroda green marble slab having semi round nosing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20mm (Twenty millimetre) thick base cement mortar 1:4 (One cement isto four coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etcetera complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Providing and fixing 50mm (Fifty millimetre) dia M.S. hollow square / rectangular pipe of 14 to 16 gauge / M.S flat and balusters M.S. flat / M.S square bars 19mmx19mm (Nineteen millimetre into nineteen millimetre) with 3 nos @ 16mm (Sixteen millimetre) mid rail connected at the side of the baluster with fixtures .Tand fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approved drawing, design and specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing factory made ridges or hips having proper gola shape 60cm (Sixty millimetre) overall with 0.60mm (Zero point six zero millimetre) thick prepainted steel sheets in roofing with hot dipped metalic zinc coated sheets with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating of Tata / Sail / Reliance / Jindals steels i/c fixing with prepainted iron J or L hooks, bolts & nuts 6mm dia & prepainted G.I. limpet and bitumen washers complete as per approved drawing, design and specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 0.60mm (zero point six zero millimetre) thick prepainted steel sheet (IS marked Z-120) of TATA Durashine / Reliance / Jindal Steel over steel trussed in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 (Twenty) microns over 5 (Five) microns primer coating of back coat of polyster of 5 (Five) microns over 5 (Five) microns primer coating including fixing with prepainted iron J or L hooks,bolts and nuts 6mm (six millimetre) diametres with prepainted limpet, rubber washers complete with all accessories as required as per specification, drawing and design and specifications.and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Octroi, Toll tax, GST or any other taxes imposed by the Government.

Providing and fixing valley 90cm (Ninety centimetres) overall 0.60mm (Zero point sixty millimetres) thick prepainted steel sheet of Tata Durashine /Sail /Reliance /Jindals steels in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 (five) microns over 5 (five) microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetres) dia with prepainted G.I. limpet and bitumen washers complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing M.S. B.P. sheet 2.0mm (Two point zero millimetre) thick in eaves board/facia/ soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured and paid separately) including fixing complete as per architectural drawings including carriage of material, within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing flashing 38cm (Thirty eighty centimetre) overall with 0.60mm (Zero point six zero millimetre) thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia meter & prepainted G.I. limpet & bitumen washers complete as per architectural drawings including carriage of material, within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 30cm (Thirty Centimetre) wide 30cm (thirty centimetre) deep 0.60mm (Zero point six zero millimetres) thick plain P.G.I. sheet gutter having dome shaped grating with bolts, nuts and washers etcetera including making necessary connections with rain water pipe complete including carriage of material, within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundered fifty millimetre) on wall face PVC acessories for rain water pipes working pressure 4/6 kg/cm2 (Four/Six kilogram per centimetre sqaure) ISI marked of Finolex / Relpipe (Reliance)/Vectus including priming coat, painting and welding etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundered fifty millimetre) Plain Bend on wall face PVC acessories for rain water pipes working pressure 4/6 kg/cm2 (Four/Six kilogram per centimetre sqaure) ISI marked of Finolex / Relpipe (Reliance)/Vectus including priming coat, painting and welding etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundered fifty millimetre) Plain Shoe on wall face PVC acessories for rain water pipes working pressure 4/6 kg/cm2 (Four/Six kilogram per centimetre sqaure) ISI marked of Finolex / Relpipe (Reliance)/Vectus including priming coat, painting and welding etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing PVC clamps of approved design to PVC rain water pipe and making good the walls etcetera; as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x600x6mm Everest board or its equivalent ceiling cacade in powder coated GI channel framing @ 600mm centre to centre complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Structural steel work of Tata/Sail riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, Toll tax, Sale tax, GST or any other taxes imposed by the Government.

Painting two or more coats (excluding priming coat) on new steel and other metal surfaces with enamel paint of approved brand and manufacture enamel (Narolac/Asian paints) other than white and of approved shade brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government.

Painting two or more coats (excluding priming coat) over new wood and wood based surfaces with enamel paint of approved brand and manufacture (Narolac/Asian paints) and of approved shade to give an even shade including cleaning the surface of all dirt, dust and other foreign matter complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government.

6mm (six millimetre) thick cement plaster to ceiling with cement mortar 1:3 (one cement isto three sand), upto all floor level complete as per HPPWD specifications approved drawing, design and as directed by the Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Royality, Malkhana, Octroi, GST, Toll Tax Sales tax or any other taxes imposed by the Government.

15mm thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor levels including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth with cement mortar 1:6 (one cement isto six sand) as per specifications, approved drawing, design as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

15mm thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth with cement mortar 1:6 (one cement isto six sand) as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

15mm thick cement plasters in single coat on fair side of brick/concrete/stone walls for interior plastering upto all floor levels including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetre) in girth and finished even and smooth with cement mortar 1:4 (one cement isto four sand) as per specifications, approved drawing, design as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

50mm (Fifty millimetre) thick cement concrete flooring 1:2:4 (One cement isto two sand isto four graded stone aggregate 20mm (Twenty millimetre) nominal size laid in one layer finished with a floating coat of neat cement complete as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

20mm (Twenty millimetre) cement plaster in two coat backing coat 10mm (Ten millimetre) and finishing coat 10mm (Ten millimetre) thick on fair side of brick/stone masonary walls for interior plastering up to floor two level including aamses internal rounded angle chamfers and or rounded angle cement mortar 1:4 (One cement isto four sand) complete as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Applying Birla/J.K white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose material and other foreign matters, sand papered smooth to give final matt finish to the surface complete as per specification, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Finishing walls with apex weather proof exterior emulsion of Asian / Dulux / Berger / Nerolac Suraksha paints of approved shade having VOC less than 50 gm/litre (Fifty gram per litre) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives New work (Two or more coats applied @ 1.43 litre/ 10 sqm (One point forty three litre per ten square metre) over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (Zero point ninety litre per ten square metre) upto all floor level complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Distempering (two coats) with Acrylic and Synthetic oil bound washable distemper with Nerolac/ Asian of approved brand and manufacture and of required shade on undecorated wall surfaces to give an even shade of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matters and also including preparing the surface even and sand papered smooth as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

White washing with lime to give an even shade New work (three or more coats) complete as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Forming 15mm (Fifteen millimetre) wide and 15mm (Fifteen millimetre) deep groove of uniform size in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer, including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications, approved drawing, design, as per entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Random rubble masonry with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (One cement isto Six coarse sand isto Twelve graded stone aggregate 20mm (Twenty millimetre) nominal size upto plinth level including raking out joints in cement mortar 1:6 (One cement isto Six coarse sand) complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing Plinth protection with 60mm (Sixty millimetres) thick interlocking paver blocks of NTC with 23cm (Twenty three centimetres) diametre Half round reinforced cement concrete pipe for drainage purpose fixed over 10cm (Ten centimetres) thick cement concrete 1:5:10 (One cement isto five sand isto ten graded) stone aggregate bedding complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete interlocking block 60mm (Sixty millimetre) thick (M35) Made with vibration technology PVC / Fibre moulds pew polished of NTC ISI marked IS No 15659 or its equiivalent as per approved shade and sample including border or kurb block grey or coloured over sub-base of concrete with 25mm (Twenty millimetre) thick average thickness of cement mortar 1:4 (One cement isto four sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing and polishing complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:3:6 (One cement isto Three sand isto Six graded stone aggregate 40mm (Forty millimetre) nominal size and curing complete excluding cost of form work in foundation and plinth complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

20mm (Twenty millimetre) cement Pattern in Plaster With cement Mortar 1:4 (One cement isto four coarse sand) complete and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Raised Band 12mm (Twelve millimetre) thick plain cement mortar bands in cement mortar 1:4 (One cement isto four fine sand) complete and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing to wall ceiling and floor ploythelene aluminium ploythelene (PE.AL.PE) composite pressure pipe U.V stabilized with carbon black and fitting of kitec confirming to ISI 15450-2004 for water supply complete with necessary pipe fitting including cutting, fixing and making good the walls ceiling and floor of approved brand complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Octroi, GST, Toll Tax, Sales tax or any other taxes imposed by the Government. 1620 (20mm (Twenty millimeter) outer diameters)

Providing and fixing to wall ceiling and floor ploythelene aluminium ploythelene (PE.AL.PE) composite pressure pipe U.V stabilized with carbon black and fitting of kitec confirming to ISI 15450-2004 for water supply complete with necessary pipe fitting including cutting, fixing and making good the walls ceiling and floor of approved brand complete as per HPPWD specifications and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate inclusive of Octroi, GST, Toll Tax, Sales tax or any other taxes imposed by the Government. 2025 (25mm (Twenty five millimeter) outer diameters)

Making connection of galvanised steel distribution branch with galvanised iron main 20mm to 40mm (twenty to forty milimeter) nominal bore by providing and fixing tee including cutting and threading the pipe complete as per approved drawing, design and specifications and as per direction and entire satisfaction of Engineer-in-Charge, including carriage of material within all leads, lifts and other incidentals. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (One hundered ten millimetre) nominal bore/diametres High pressure PVC PVC spigot and socket, waste and ventilating pipes 4.00 to 4.6mm thick (Four point zero zero to four point six millimetre) of Finolex/Vectus/Relience including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) nominal bore/diametres High pressure PVC PVC spigot and socket, waste and ventilating pipes 4.00 to 4.6mm thick (Four point zero zero to four point six millimetre) of Supreme/ Kisan/ Astral including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundered ten millimetre) nominal bore/diametres High pressure PVC PVC spigot and socket, waste and ventilating pipes of Supreme/ Kisan/ Astral including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundered ten millimetre) nominal bore/diametres P.V.C clamps ISI marked of Supreme/ Kisan/ Astral etcetera including finishing with approved design with steel screws and rawal plugs etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) nominal bore/diametres P.V.C clamps ISI marked of Supreme/ Kisan/ Astral etcetera including finishing with approved design with steel screws and rawal plugs etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) diametre P.V.C. Supreme/ Kisan/ Astral heal rest Confirming to BIS-14735 including filling the joints with approved adhesive complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) diametre P.V.C. Supreme/ Kisan/ Astral heal rest Confirming to BIS-14735 including filling the joints with approved adhesive complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) P.V.C. (Polyvinyl chloride) plain bend make of Supreme/ Kisan/ Astral of approved manufacture ISI marked including fixing with approved adhesive etcetra complete and carriage of material within all leads, lifts and other incidental Charges. The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) P.V.C. (Polyvinyl chloride) plain bend make of Supreme/ Kisan/ Astral of approved manufacture ISI marked including fixing with approved adhesive etcetra complete and carriage of material within all leads, lifts and other incidental Charges.The rate is including Royality, Malkhana, Octroi, Toll Tax, Sale Tax, GST or any other taxes imposed by the Government.

Providing and fixing 110mm (One hundered ten millimetre) nominal size PVC Collar of ISI marked Conforming to BIS-14735-99 of Supreme/ Kisan/ Astral including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) nominal size PVC Collar of ISI marked Conforming to BIS-14735-99 of Supreme/ Kisan/ Astral including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundered ten millimetre) nominal size PVC Cowl of ISI marked Conforming to BIS-14735-99 of Supreme/ Kisan/ Astral including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 75mm (Seventy five millimetre) nominal size PVC Cowl of ISI marked Conforming to BIS-14735-99 of Supreme/ Kisan/ Astral including filling with approved adhesive etcetera complete in all floor level/height complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110x90mm (One hundred ten into ninety millimetres) nominal size/ diameter PVC floor trap ISI marked Supreme/Kitch/Finolex/Kisan/ Astral Conforming to IS-14735-99 of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110x75mm (One hundred ten into seventy five millimetres) nominal size/ diameter PVC floor trap ISI marked Supreme/ Kitch/Finolex Conforming to IS-14735-99 of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing vitreous China wash down water closet (European type W.C. pan) Wall mounted WC size 655x350x735mm (Six hundred fifty five into three hundred fifty into seven hundred thirty five millimetre) of Cera / hindware / Jaquar with 10 litre low level PVC flushing cistern (Sleek plus) having dual flush system with fitting and brackets, 40mm (Forty millimetre) flush bend, 20mm (Twenty millimetre) over flow pipe, with seat & lid fixed with C.P. brass hinges and rubber buffers,with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and and fixed with jet pressure and intergal P or S trap including jointing the trap and soil pipe with adhesive of approved brand. (Jet Spray to be measured and paid for separately) complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing water closet squatting pan (Indian type W.C. pan) White Vitreous china Orissa pattern WC 580x440 mm (Five hundred eighty into four hundred forty millimetre) of Cera / hindware / Jaquar with integral type foot rests with 100 mm (One hundred millimetre) sand cast Iron P or S trap, 10 (Ten) litre low level P.V.C. flushing cistern, and as shown in the drawing / as per details including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing vitreous China wash basin Delta No.10010 having size 550x400mm (Five hundred fifty into four hundred millimetre) of HINDWARE/ or its equivalent with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing stainless steel kitchen sink of Diamond, big size 610x510x200mm (Six hundred ten into five hundred ten into two hundred millimeters) of approved make with drain board and C.P waste with C.I or M.S brackets painted white including cutting holes in walls and making good the same complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm nominal size diameters rubber plug for wash basin (Heavy duty makes ISI marked is No. 8931 7893). complete including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimetre) dia M.I.union for Wash basin and sink long and 15mm (Fifteen millimetre) nominal bore with brass union complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Mixer for kitchen sink with casted swinging spout at top complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (Thirty two millimeters) nominal diameters PVC waste for wash basin or sink complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing two hole basin mixing Faucet complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 100mm (One hundred millimetre) dia chromium plated (Heavy duty makes ISI marked) IS No. 8931 & 8934 grating of superior quality for floor, gully or nahani trap complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 750mm (Seven hundred fifty millimetre) dia chromium plated (Heavy duty makes ISI marked) IS No. 8931 & 8934 grating of superior grating of superior quality for floor, gully or nahani trap complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 150mm (One hundred fifty millimetre) nominal bore/diameters. (to level or slopes) PVC pipes grade 'A' and jointing with approved adhesive ncluding testing of pipes and joints complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing flat back 600x450mm (Six hundred into Four hundred fifty millimetres) beveled edge mirror of Opel of Jaquar / ESS-ESS of hoteior series of superior glass (of approved quality) complete with 6mm (Six millimetre) thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x20mm (Six hundred into twenty millimeters) C.P brass towel rail. (Heavy duty makes ISI marked) IS No. 8931 & 8934 with C.P. brass brackets fixed to wooden plugs with C.P. brass screws complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws :-Plastic container complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Chromium plated brass soap dish with brackets fixed to wooden plugs with C.P. Brass screws complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing chromium plated brass toilet paper holder of approved brand and manufacture continental series of Jaquar/contessa series of Hindware complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing C.P jet spray chromium plated (Heavy duty makes ISI marked) IS No. 8931 & 8934 grating of superior with 1.5mtr (one point five metre) tube complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimeters) diameters C.P. brass bib tap chromium plated (Heavy duty makes ISI marked) IS No. 8931 & 8934 of approved quality (superior or heavy type) and colour of prayag polynets syonet complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millimeter) dia CP brass stop cock chromium plated (Heavy duty makes ISI marked) IS No. 8931 & 8934 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimeters) diameters C.P. brass Pillar tap with capstan head chromium plated (Heavy duty makes ISI marked) IS No. 8931 & 8934 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millmeters) C.P. brass angle valve chromium plated (Heavy duty makes ISI marked) IS No. 8931 & 8934 without nuts and pipes complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimeters) nominal bore brass full way valve with wheel complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (fifteen millmeters) nominal bore C.P. brass valve (Horizontal plunger) type High pressure with polythene plastic floats of (Heavy duty makes ISI marked) IS No. 8931 & 8934 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing PVC connection pipe with brass unions ISI marked 45cm (forty five centimeters) long and 15mm (fifteen millimeters) nominal bore complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 32mm (thirty two millimeters) nominal diameters PVC waste pipe for wash basin or sink including brass check nut complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetre) nominal size PVC single equal branch with oval access door, ISI marked of Finolex/Kitch/Supreme including insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC single equal branch with oval access door, ISI marked of Finolex/Kitch/Supreme including insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetre) nominal size PVC double equal branch with oval access door, ISI marked ofFinolex/Kitch/Supreme including insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC double equal branch with oval access door, ISI marked ofFinolex/Kitch/Supreme including insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetre) nominal size PVC door bend with oval access door, insertion rubber washer 3mm (Three millimetre) thick ISI marked of Finolex/Kitch/ Supreme including fixng with approved adhesive etcetera complete in all floor level/height etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal size PVC door bend with oval access door, insertion rubber washer 3mm (Three millimetre) thick ISI marked of Finolex/Kitch/ Supreme including fixng with approved adhesive etcetera complete in all floor level/height etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetre) nominal diametre PVC offset 45° of Finolex / Kitch /Supreme ISI marked including fixing with approved adhesive in all floor level/height etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110mm (One hundred ten millimetre) nominal diametre PVC offset 45° of Finolex / Kitch /Supreme ISI marked including fixing with approved adhesive in all floor level/height etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and placing on terrace (at all floor levels polyethylene water storage tank, tripple layer of Finolex/Kitch/Supreme IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:4:8 (One cement isto four sand isto eight graded crushed stone aggregate 40mm (Forty millimetres) nominal size in all round for PVC pipe of 150mm (One hundred fifty millimetres) internal diametre including bedding necessary form work and curing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:3:6 (One Cement isto three Sand isto six graded stone aggregate 40mm (Forty millimetre) nominal size in haunching of PVC. pipes of 150mm internal diameters, including concrete for beddings necessary form work and curing complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing vitreous China pedestal of Hindware/Cera/ Jaquar for wash basin complete recessed at the back for the reception of pipes and fittings complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x120x5mm (Six hundered into One hundered twenty into five millimetres) glass shelf of Opel of Jaquar / ESS-ESS of hoteior series with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40mm (Fofrty millimetre) long screws, rawl plugs etcetera including necessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Tooth brush and Tumbler holder (Vitreous China) complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement isto four coarse sand) with R.C.C. top slab with 1:1.5:3 mix (one cement isto one & half coarse sand isto three graded stone aggregate 20 mm (Twenty millimetres) nominal size), foundation concrete 1:4:8 mix (one cement isto four coarse sand isto eight graded stone aggregate 40mm (Forty millimetres) nominal size), inside plastering 12mm (Twelve millimetres) thick with cement mortar 1:3 (one cement isto three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement isto two coarse sand isto four graded stone aggregate 20mm (Twenty millimetre) nominal size finished with floating coat of neat cement complete as per standard design Inside size 90x80 cm (Ninety into eighty centimetres) and 45 cm (Forty five centimetres) deep including C.I. cover with frame (light duty) 455x610 mm (Four hundred fifty five into six hundred ten milimetres) internal dimensions, total weight of cover and frame to be not less than 38 kg (Thirty eight kilogramme) (weight of cover 23 kg (Twenty three kilogramme) and weight of frame 15 kg (Fifteen kilogramme)) With Sewer bricks conforming to IS : 4885 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Constructing brick masonry manhole in cement mortar 1:4 ( one cement isto four coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (one cement isto one & half coarse sand isto three graded stone aggregate 20mm (Twenty millimetres) nominal size), foundation concrete 1:4:8 mix (one cement isto four coarse sand (zone- III) isto eight graded crushed stone aggregate 40mm (Forty millimetres) nominal size), inside plastering 12mm (Twelve millimetres) thick with cement mortar 1:3 (one cement isto three coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (one cement isto two coarse sand isto four graded crushed stone aggregate 20mm (Twenty millimetres) nominal size) finished with a floating coat of neat cement complete as per standard design Inside size 120x90cm (One hundred twenty into Ninety centimetres) and 45 cm (forty five centimetres) deep including C.I. cover with frame (medium duty) 455x610mm (Four hundred fifty five into six hundred ten millimetres) internal diameter, total weight of cover and frame to be not less than 38 kg (Thirty eight kilogramme) (weight of cover 23 kg (Twenty three kilogramme) and weight of frame 15 kg (Fifteen kilogramme)) : With Sewer bricks conforming to IS : 4885 complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (One cement isto four coarse sand) C.I. cover with frame (light duty) 455x610mm (Four hundred fifty five into six hundred ten millimetre) internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (One cement isto one & half Fine sand isto three graded stone aggregate 20mm (Twenty millimetre) nominal size), foundation concrete 1:5:10 (One cement isto five fine sand isto ten graded stone aggregate) 40mm (Forty millimetre) nominal size, inside plastering 12mm (Twelve millimetre) thick with cement mortar 1:3 (One cement isto three coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etcetra complete as per standard design Inside dimensions 455x610mm (Four hundred fifty five into six hundred ten millimetre) and 45cm (Forty five centimetre) deep for single pipe line : 19.30.1.1 with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven point five) complete as per approved drawing, design, specifications and as per directions and entire satisfaction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Excavation in drains and channels etcetra in earth work in all kind of classification of soil such as pick work, jumper work, pick-jumper work, blasting work, soft and hard blasting and saturated soil, including chiselling or wedging out rocks where blasting work is prohibited or any other mixed variety of soil includinig shoring, strutting, de-watering and pumping or bailing out water (surface and sub soil water) upto any depth or any quantum of water including slush which may arise during de-watering or removal of slush, lift upto any height stacking the excavated soil clear from the edge of excavation and then returning the stacked soil in 15cm (fifteen centimetre) layers when required into plinths, sides of foundation etcetra consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated earth as per specification, approved drawings, design as per the entire satisfaction and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of Octroi, Royality, Malkhana, toll tax, sale tax, GST or any other taxes imposed by the Government.

Providing and fixing 20mm (Twenty millimetres) nominal bore in trenches galvanised mild steel tubes (heavy grade) ISI make approved quality tube fitting tube fitting and clamps complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen milimetres) nominal bore in trenches galvanised mild steel tubes (heavy grade) ISI make approved quality tube fitting and clamps complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and fixing cast iron cover with rectangle frame 455x610mm (Four hundred fifty five into six hundred ten millimetre) (light duty) single seal pattern having weight not less than 23kg (Twenty three kilogramme) as per HPPWD specifications complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and fixing cast iron cover with rectangle frame 455x610mm (Four hundred fifty five into six hundred ten millimetre) (light duty) single seal pattern having weight not less than 23kg (Twenty three kilogramme) as per HPPWD specifications complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing of water lifting pump of 1.00 HP (One point zero horse power) of serex/Kirloskar/ Crompton/Wortington including all necessary fittings complete in all respect including entire carriage of materials within all leads lifts and other incidentals, and as per specification and as per directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing 20x20mm (Twenty into twenty millimetre) square bar M.S Foot rest including fixing in man holes with 20x20x10cm (Twenty into twenty into ten centimatre) cement concrete 1:3:6 (one cement isto three sand isto six graded /crushed stone aggregate) 20mm (Twenty millimetre) nominal size as per standard design complete in all respect including entire carriage of materials within all leads lifts and other incidentals, and as per specification and as per directed by the Engineer-Incharge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.