25/EUCC-V/LESA/2022-23

Amount

Dragging, loading, carriage and unloading of following store materials with proper stacking from ESC Daliganj to JE dumps store and from JE dump store to work site within municipal area.

5 MVA T/F

33 KV 3x300 sq mm XLPE Cable

33 KV 3x300 sq mm XLPE O/D J/Kit

11 KV 3x300 sq mm XLPE Cable

11 KV 3x300 sq.mm Cable Jointing Kit I/D

11 KV 3x300 sq.mm Cable Jointing Kit O/D

33 KV VCB 800 Amp 750 MVA

33 KV CT 200/100/1 amp

Single T/F Control Panel

Bus Coupler 350 MVA

33 KV Bus Isolator

33 KV Lightening Arrestor

11 KV 3x185 sq.m.. XLPE Cable

11 KV 3x185 sq.m.. XLPE O/D J/KIT

11 KV 3x185 sq.m.. XLPE I/D J/KIT

11 KV 3x185 sq.m.. XLPE St/TH J/KIT

ST Pole 11 Mtr. Long

M.S. Channel 100x50 sq mm 10 kg / Mtr.

M.S.Angle 65x65x6MM 5.8 Kg / Mtr

11 KV Pin Insulator

MS earthing rod 20x2500 mm

11 KV Pin with Nut

Earthing By earth rod

LT PVC Cable 1x240 sq mm

Panther Conductor

11 KV VCB I/C CTR 600/300/5 amp, 350 MVA

11 KV VCB O/C CTR 200/100/5 amp, 350 MVA

M.S. Channel 125x65mm 3.5m long 4 Nos Pieces [email protected] Kg. Mtr. With wastage

M.S.Angle 75x75x6, 2.6 Mtr, 2 Nos Total [email protected] Kg./M with wastage

Rail 105 Lbs 9 Mtr Long

MS Round of 32 mm dia for laying of main earthmat in switch yard & for panel earthing bridge [email protected] Kg./M

MS Round of 32mm dia for making MS earth electrode 32x3000mm. [email protected] Kg./M

M.S. Channel 100x50 sq mm 10 kg / Mtr.

11 KV 3x185 sq.mm XLPE Indoor termination kit

11 KV 3x185 sq.mm XLPE Outdoor termination kit

One 11 KV O/G Feeder Erection Work

Fabrication, erection, grouting, plinthing & painting of double pole cable exposure of ST. Pole 11 Mtr long for 11 KV line with fixing of necessary clamp channel, angle, danger board, number plate, 11 Kv pin & pin insulator making ckt 3 phase 3 wire bus bar with single core cable as per RESPO Norms with electrode earthing as per Norms.(STP, Channel, angle & 11 KV pin Insulator shall be provided by the department)

Laying of 11 KV XLPE Cable 3Х185 sqmm D/C by digging of trench 900 mm deep & 750 mm wide its boxing with bricks & sand, laying of cable & separation of cable by brick wall, filling of sand upto top cover of the trench properly leveling & ramming & covering with stone slab after laying of cable and Fixing of cable Route Marker stone (All material will be provided by contractor except 11 kv cable)

Laying of 11 kv 3Х185 sqmm XLPE double cable by HDD method.

Digging of pit size 3Х2Х1 mtr for making straight through joint 11 kv, also work involved filling of soil levelling and ramming of the same

Making heat & shrinkables joints of following size and types for XLPE Cable by heat and shrinkables jointing kits.(Jointing kit will be provided by deptt.)

Straight through for 11 kv 3Х185 sqmm XLPE Cable

33 KV 3x300 sq mm XLPE O/D J/Kit

11 KV 3x185 sq mm XLPE I/D J/Kit

11 KV 3x300 sq mm Cable jointing kit I/D

11 KV 3x300 sq mm Cable jointing kit O/D

11 KV 3x185 sq.m.. XLPE O/D J/KIT

Cable Hosting of 11 KV 3x185 with help of GI Pipe 3" dia having length 3 mtr. including jumpering etc complete. All Material provided by contractor.

Supply and fixing of 11 KV Cable stand structure with fuse set. All Material will be provided by contractor.

11 KV 3x185 sq. mm cable hosting on cable stand & switchgear

High pressure testing of 11 KV 3x185XLPE cable along with arrangement of High Pressure equipment.

Switch Yard Work

Excavation of earth for laying of earth mat 750 mm deep and proper levelling after laying of earth mat complete work.Reveling should not below the Road level.

Laying of earth mat 32mm round bar including cutting ,shaping fixing, jointing including cost of labour and materials (except round bar)

Cutting ,fabrication and driving of earth electrode of size 32x3000 mm

Cutting shaping, laying and welding of riser strip size 50x6mm G.I strip of size 50x6 mm in between earth mat and equipments /structure/body of T/F for earthing (two nos Riser for each structure equipment individually GI Strip shall be provided contractor )

Preparation of joint and proper welding as per RESPO Specification

Lap joints

Cross joints

Electrode joints

Laying of 33 KV 3x300 sq. mm XLPE cable double circuit digging of trench 1050 mm deep, 750 mm side including supply of required material, 1st class bricks, stone pad & fine sand. The inter spacing between two cable should be in between 0.25 m to 0.40m. The cables shall be laid in trench by first filling layer of sand and laying on sides with bricks, fixing bricks as partitions between two cables, after laying cable, covering cable by stone pads resting on bricks, covering it by earth, all work as per RESPO norms. (Allmaterial required for laying will be supplied by the contractor except 33 KV XLPE cable).

Fabrication of lightening arrestor/CT structure/.as per RESPO Norms Digging of two Nos. pits of size 1.075x0.3x0.3Mtr providing stone pad at the bottom of the pit and grouting of two legs of the above structures in CC (Cement, coarse sand and stone grit of 20mm gauge ) of ratio 1:4:8 in block of 1.075Mtr X0.3Mtr including supply of all civil material complete in all respect. Both plinths of the structures shall be properly finished with champering of edges etc.

Fabrication of isolator structures 3.5 Mtr. In height as per RESPO NORMS. Digging of two Nos. pits of size 1.075x0.9x0.3 Mtr. providing stone pad at the bottom of the pit and grouting pad at the bottom of the pit and grouting of two legs of the isolator structure in CC (cement coarse sand and stone grit of 20m.m gauge)of the ratio 1:4:8 in block of 1.075Mtrx0.3 mm including supply of all T&P complete in all respect. Both plinths of the isolator structure shall be properly finished with smoothening of edges.

Construction of plinth of size 2.0 mtr x 1.5 mtr x 0.9 mtr suitable for erection of upper structure for 33KV VCB including grouting of anchor bolts in proper alignment and level. Scope of work includes excavation of foundation base concreting in CC 1:6:12(cement, fine sand & brick ballast ),1st class brick work in cement mortar of ratio 1:4 CC in ratio 1:4:8 and RCC work in ratio 1:2:4(cement coarse sand and stone grit of 20mm gauge )as per drawing.

Fabrication of structure, grouting, plinthing and painting of all structure equipment.

Mounting of accessories/equipment on fabricated structure complete work with making proper alignment and tightening the work includes fabrication work if required for proper operation of equipment .

33 KV VCB

33KV lightning Arrestors

Bus/Line Isolator

Construction of Power T/F plinth suitable for 33/11KV 5 MVA power T/F of size 4x3x1.3 having 0.4 mtr height above ground level. The work includes excavation of foundation base concreting in cc ratio 1:6 M as 12 1st class brick work in ratio 1:4 with coarse sand ,foundation cc in ratio 1:4:8 using M.S bar of 12 mm dia for reinforcement the work includes laying of 2 nos rail pieces 4 mtr long as per drawing/practice the plinth shall be finished in all respect. (only rail piece and M.S angle provided by the department)

Safe dragging of 33/11 KV 5 MVA T/F and its accessories like radiator, conservator tank, exposure event from unloading place upto T/F plinth its placement on plinth and with proper aligment approximate 25 mtr distance with help of crane sleeper and man power etc.

Erection and commissioning of 5 MVA T/F mounting of radiator conservator tank exposure vent etc. Filling of T/F oil in radiator conservator tank with complete work including neutral stand and 33 KV cable stand structure as per RESPO Norms.

Laying of double circuit 11KV 3x300 sq mm XLPE cable in cable trench with proper ferrurling. Cable trench should filled by fine sand.

Hoisting, jumpering, clamping of 11KV 3x300 sq mm XLPE cable on cable stand and panel with proper taping with the help of empire tape. PVC tape and connectors.

Earthing of Sub-station equipment and Power Transofmer by boring and lowering of "B" class GI pipe 50mm dia from ground upto the water level (minimum 30 meter deep) as per standard practice

Jumpering complete line bay & T/F bay with ACSR panther Cond. and required PG clamp with nut & Bolts from 33KV cable to T/F (with copper L piece) complete work. All material provided by contractor except panther conductor.

Construction of cable trench of size 150 mm wide 300 mm deep with brick work along with provision trench cover M.S strip at the interval of 0.30 M and M.S angle at both the edge of the trench.

Construction and fixing of trench cover0.5 M wide 0.75 mm thick with cement, coarse sand & stone grit in ratio 1:2:4 for covering of cable trench150 mm wide with provision of M.S Angle and MS Bar as per RESPO Norms

Laying of copper control cable in control cable tray of following sizes its proper dressing ferruling and connection with the system. Control cable, cable tray shall be provided by contractor.

2x2.5 sq mm

4x2.5 sq mm

6x2.5 sq mm

Supply and Erection of 1.98 MVAr Capacitor Banks at 33/11 KV 5 MVA Transformers

Providing and fixing of 24 volt battery set and charger as per RESPO Norms.

Installation & commissioning of 24 V batteries set with charger include intial charging complete.

Hoisting of 33 Kv 3x300 sq mm Cable on Cable Stand. All Material Provided by contractor except cable.

Fabrication and grouting of M.S Angle 75X75X6 mm in L shape & in proper size and alignment to provide support for the two separate earthing strips for power transformer neutral including supply and fixing of two nos. Flexible copper bonds for neutral earthing.

Fabrication and erection of cable support made of two pieces of M.S channel 100x50mm,3.0 Mtr.long joined to each other by means of 5 Nos. M.S Flat 50x6mm pieces of size 150mm long each by welding at equal intervals as per drawing and grouting in a block of size300x300x700mm complete with one coat of ready mixed primer and two coats of aluminium paint. This includes providing of four nose M.S clamp made of M.S flat holding the cable including nuts and bolts and fixing of XLPE Cable.

Shifting carefully & safely 11KV I/C & O/G switchgear from outside of the switchgear room, as per direction of Engineer incharge, placing and fixing of switchgear on foundation providing G.I, Nuts & Bolts of proper size in proper position and alignment and checking, complete work with Mounting of P.T on incoming S/G.

Fixing and making bus bar connections in between all switch gearsafter cleaning and tapping with H.T.Tape,empire tape and PVC tape properly, providing and fixing of 6 mm thick Bakelite separators and plugging of all opening & holes with plastic compound complete work including cost of all material (except copper Bus Bars)strictly to the satisfaction of site in- charge.

Shifting carefully, installation & commissioning of 33KV single circuit transformer control panel in control room including grouting of above.

Civil Work

Dismantling brick work or stone work in lime or cement mortar and including stacking of materials as directed by the Engineer-in-charge within a distance of 60 metres.

Dismantling reinforced cement concrete or reinforced brick work, including stacking of dismantled materials as directed by the Engineer-Incharge within a distance of 60 metres.

Dismantling cement concrete or brick or granolithic floors including base concrete and including stacking of dismantled materials as directed by the Engineer In-charge within a distance of 60 metres.

Scrapping old white or colour wash or distemper including disposal of refuse as directed by the Engineer-I/C within a distance of 60 M.

Excavation in foundation in ordinary soil (Loam Clay or Sand) including lift upto 1.5m and lead upto 30m and including fitting, watering and ramming of excavated earth into the trenches or into the space between the building and insides of the foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the engineer-incharge upto a distance of 30m from the foundation trenches.

Sand filling in plinth including supply of necessary quantity of local sand from a distance not exceeding 8 km from the site of work and including watering, dressing etc. Rate to including cost of all materials, labour and T&P etc. required for proper completion of work.

Earth filling under floors including cost of earth when obtained from outside Board's area including its carriage including watering ramming in 20cm layers and dressing of earth etc. all complete.

Concrete with 4 cm gauge Ist class brick ballast, coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 12:6:1 in foundations and under floors including supply of all materials, labour and tools and plants etc. required for proper completion of the work.

As in item No. (44) above but in the proportion 4:2:1 and with 20 mm gauge approved hard stone ballast including necessary centering and shuttering if required

As in item No. (44) above but in the proportion 1:1.5:3 and with 20 mm gauge approved hard stone ballast including necessary centering and shuttering if required

R.C.C. work with cement coarse sand of minimum 2.2 F.M. and 20 mm gauge ballast in the proportion of 1:1.5:3 in lintels and sunshades and other similar works excluding, supply of reinforcement and its bending but including its fixing and binding the same with 24BWG G.I. binding wire including supply of all materials, labour and T&P etc. required for proper completion of the work (Binding wire to be supplied by the contractor free of cost)

R.C.C. work in 1:1.5:3 with cement approved coarse sand (F.M. 1.8 to 2.5 and 2 cm gauge graded approved hard stone ballast in proportion in raft foundation and footings complete.

First class brick (Class-150 work in 1:6 cement and coarse sand (F.M. 1.8 to 2.5) mortar in foundation and plinth including supply of all materials, labour & T&P etc. required for proper completion of work.

First class brick (Class-150 work in 1:6 cement and coarse sand (F.M. 1.8 to 2.5) mortar in Super Structure for one brick thick wall including supply of all materials, labour & T&P etc. required for proper completion of work.

R.C.C work with cement approved coarse sand (F.M1.8 to 2.5)and 2cm gauge graded approved hard stone ballast like grainite,quartzite etc from Dalla, jhasi or other quarried and approved coarse sand in proportopn 1:1.5:3 in slab, including supply of reinforcement & its bemding but incliding its fixiing and binding the same with binding wire, including cost of all other materials labour and T&P.

As in item No. (50) above but in 1:1:5:3 for lighter beam.

As in item No. (50) above but in 1:1:5:3 for column

First class brick (Class-150 work in 1:4 cement and coarse sand (F.M. 1.8 to 2.5) mortar in Super Structure for half brick thick wall including supply of all materials, labour & T&P etc. required for proper completion of work.

S/F of brick bats in soak pit including supply of all labour,material T&P etc. required for proper completion of work

First class brick laid dry in foundation and plinth as in circular soakpit walls of one brick thickness and 2.0 to 3.0M depth including cutting moulding bricks as required including cost of all materials labour and T&P complete. (CSI No. 6.16)

Supply and fixing of 32 mm thick commercial quality Sitapur plywood flush door shutters including fixing of wooden cleats and stoppers and including fixing and adjustment of oxidized hinges, bolts, locks, handles, springs and/or other fitting and including their supply and including painting with two coats of black Japan on all iron fittings if necessary.

Mild steel or Iron work in heavy sizes such as trusses, built up gates, door and window frames, trench cover and edging boundary posts etc. wrought to required form including drilling holes, rivetting or welding where necessary band also including supply of all steel sections, bolts nuts etc. and their fixing including erection of the structures in proper positions and alignments as per direction of E/I. Labour and T&P etc. required for proper completion of the work.

Mild or ribbed for steel work in plain work such as RCC or R.B. work wrought to required shape as necessary including cutting and bending for proper completion of the work including supply of steel and wastage, labour T&P etc. required for proper completion of the work. Authorised over lapes, hooks and bends shall be measured.

Providing & fixing steel glazed window and ventilators of standard rolled mann or mahavir steel sections confirming to IS7452-1974 as per drawing joints metered and welded within 100x14x3.15 mm holdfast embaded in cement concrete block 15x10x10 cm. size of 1:3:6 proportion i.e. 1 part of cement 3 part of approved coarse sand and part of graded stone (aggregated 20mm nominal size) including S/F of glass panes of plain pin headed 4 mm thick nuts glazzing clips and special putty of approved make complete and including cost of redoxide paint. The fabrication should confirm to ISI038-1975. Aluminum beading with rubber packing including.

S/F galvanised mosquito proof heavy quality iron wire gauge of expanded metal of heavy quality over windows and including its fixing over windows with M.S. flat of 25x3 mm size both side with Nittle, fold screws including cost of material, labour and T&P etc. complete with a coat of Red oxide on M.S. flat

S/F Fan hooks 16 mm dia 200 mm long complete as per

P/F in position collapsible steel shutter with vertical channels 20 x 10 x 2 mm.(3/4" x 3/8"x 1/12") and braced with flat iron diagonals 20 x 5 mm.(3/4" x 3/16") size with top and bottom rails of "T"iron 40 x 40 x 6 mm. (1/2" x 1-1/2" x 1/4") with 38 mm dia steel pullys with bolts, nuts, nuts locking arrangement, stoppers, handles complete including applying a priming coat of approved Red oxide paints.

6 mm. thick plaster with 1:3 cement & coarse sand including labour, materials & T&P etc. required for proper completion of the work.

12 mm thick cement plaster in 1:6 cement and coarse sand (FM 2.20) mortar including supply of all mataerials,& T&P etc. required for proper completion of the work.

Add for extra labour and materials for plaster over rough face of one brick thick wall

Providing (12x15) mm section groove in plaster including all material, labour and T&P etc. required for proper completion of the work.

Making drip course (25x12mm) in 1:2 cement and coarse sand mortar including all material, labour and T&P etc.

Fire brick work (230x115x75) with 6mm thick fire cement ACC mortar in foundation & Super Structure including supply of all materials, labour and T&P etc. required for proper completion of the work.

3 mm thick floating coat of neat cement finish including supply of all materials, labour and T&P etc. required for proper completion of the work. (including cost of cement) cement consumtion 0.044 bag/Sqm.

Providing and laying 18 mm. thick Kota stone in flooring or skirting over base cement mortar 1:4 mix and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete and including supply of all materials labour and T&P etc required for proper completion of the work.

4.0 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and T&P etc, required for proper completion of the work. without base CC

First class bricks on edge floor laid dry, joints sand filled, including preparation of base to proper slope and its ramming including supply of all material labour & T&P etc. required for proper completion of the work.

S/F 8 mm white glazed floor tiles of somany,johnson or equivalent make of size 300x300 mm laid with 1:3 cement & approved coarse sand mortar finished with white cement slurry, jointing & polishing complete, including supply of all materials, labour & T&P etc. required for proper completion of the work.

S/F 6 mm white glazed tiles of size 200x300 mm in flooring laid with 1:3 cement & approved coarse sand mortar finished with white cement slurry, jointing & polishing complete, including supply of all materials, labour & T&P etc. required for proper completion of the work.

Providing and laying floor of 8 mm thick vitrified tiles in flooring or skirting of approved brand (Bell, Johnson or equi. make) size of 600x600 mm of approved shade, colour and pattern , laid over base cement mortar 1:4 mix including finishing the joints with white cement mixed with pigment to match the shade of tile including cost of all material, labour and T&P required for proper completion of the work.

Painting or varnishing previously painted iron work in small areas or wood work with two coat of approved superior quality ready mix paint "Luxol" or equivalent brand or varnish including supply of all materials, labour and T&P etc. required for proper completion of the work. Paint to be used should conform to the I.S. 103-1950.

Applying BIRLA PUTTY or equivalent putty on previousaly birla putty smoothen surface over one cost of water base cement primer of ICI or equivalent brand for smoothining and leveling of the surface as per requirement and direction of E/I including cost of all material , labour and T&P required for proper completion of work.

Two coat oil bound distemper on previously old oil bound distemper surface including supply of all materials,labour and T&P etc. required for proper completion of the work.

Painting two coat with APEX or equivalent brand weather coat paint on previously treated surface(well prepared with Birla putty and one coat of primer ICI or equivalent which shall be paid separately) including thorough washing with water including cost of all materials, labour, T&P required for proper completion of work.

Attending to petty maintenance service like plumbing service,welder service, mansion service and carpenter service required as below. Job attending by one no. Plumber/welder/mason/carpenter with one no. helper per hour or part of an hour.

Renewing panes of 4.8 to 5.7 mm glass including supply of glass with putty and brads including supply of all materials, labour and t&P etc. required for proper completion of the work.(a) glass of 4.0 mm thick.

Painting or varnishing new iron work in small areas or new wood work with one coat of ready mixed priming paint and two coat of approved superior quality ready mix paint 'Luxol" or equivalent brand or varnish including supply of all materials, labour and T&P etc. required for proper completion of the work. Paint to be used should confirm to I.S. 103-1950

Painting two coat with Acrylic emulsion paint of Berger/ Asian/ ICI or equivalent paint (Paint and water in the ratio 1:1 by volume) over prepared and primed surface of cement concrete, cement plaster and bricks including all labour, material and T&P etc required for proper completion of the work, (preparation of base with Birla putty etc. and a coating of primer shall be paid extra) .

Applying Birla or equivalent putty on new interior or exterior surface over one coat of water based cement primer or ICI or equivalent brand for smoothening and leveling of the surface as per requirement and direction of Engineer including cost of all material, labour, T&P etc. required for proper completion of work.

Painting two coat with APEX or equivalent brand weatheer coat paint on New wall surfaces (well prepared with Birla putty and one coat or primer ICI or equivalent brand for shall be paid separately) including thorough washing eith water including cost of all materials, labour, T&P required for proper completion of work .

Supply and planting English rose plants, Ashoka, Pendula, Mango, Neem etc. in beds including cost of all materials, labour T&P etc. complete in all respects

Providing and fixing of 15 mm dia B-class Jindal, JTC ISI marked G.I. pipes complete with special such as bend, tee, socket, cross clamps etc. earth work including the trenches etc. required for proper completion of the work the rate also includes concealed G.I. fitting where required cutting & making good the wall etc. and all materials labour and T&P complete

As in item No. 78 above but. 20 mm dia

Providing and fixing PVC BALL FLOAT VALVE 20 mm dia. WITH BRASS & UNION COMPLETE, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work.

Providing and fixing PVC CONNECTION PIPE, 450X15 with 2 brass units ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work.

S/F of Syntex or equivalent make water storage Tank including all material, labour and T&P etc. required for proper completion of the work.

Providing and fixing CP BRASS BIB COCK15 mm dia. HEAVY QUALITY ( 200gm) ( L & K and equi.) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work.

Providing and fixing CP BRASS Angle Valve15 mm dia. HEAVY QUALITY ( 400gm) ( L & K and equi.) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work.

Providing and fixing CP BRASS Piller cock 15 mm dia. HEAVY QUALITY ( 400gm) ( L & K and equi.) fittings, ISI mark heavy quality including supply of all materials, labour and T&P required for proper completion of work.

P/F 110 mm dia PVC pipe of 4kg/sq. cm for water supply mains and rain water pipe of Tirupati or equivalent make with specials such as Tee, Bend socket etc. including cutting of pipe where necessary and including excavation of trenches etc. complete including disposal of circlus of from the sides as per direction of Engineer Incharge complete.

P/F first quality white glazed earthern ware orrisa pattern w.c. pan size 580 mm. (Hindustan or cera) or equivalent make with 10 cm dia HCI 'P' of approved make including supply of all materials labour and T&P etc. required for proper completion of work.

Providing and fixing first quality white glazed "European type W.C.Pan Hindustan, Cera make. size 580 mm.(Hindustan,Cera Make) with out "P" trap including supply of all materials,labour and T&P etc.complete.

Providing and fixing PLASTIC SEAT COVER COMPLETE WITH PLASTIC LID FOR EUROPEAN TYPE WC ISI MARKED including supply of all materials,labour and T&P etc.complete.

Providing and fixing flat back 430X370X340 mm size lipped front urinal basin of white glazed earthern ware first quality (Hindutan, Neycer make) I.S.I. marked including supply of all materials,labour and T&P etc. required for proper completion of the work.

P/F wash hand basin (26x41 c.m.) of white glazed earthen ware of Hindustan/Perry or equivalent make complete

S/F of PVC low level cistern hindustan,or equivalent make 10 liter capacity complete with all accessories including cost of All materials, labour T&Petc. Complete

Providing and fixing 600 mm x 450 mm beveled edge mirror of Atul,Kiran makeglass with Indian polish 6.50 mm thick complete with back of 600 mm x 450 mm x 6 mm hard board sheet fixed to wooden cieats with C.P. brass screws and washers including supply of all materials, labour and T&P etc.required for proper completion of the work.

Providing and fixing 750 mm x 20 mm size C.P. brass towel rail of approved quality including brackets including supply of all materials,labour and T&P etc. required for proper completion of the work and cutting and making good the wall plaster etc. required for work.

Supply and fixing CP Nahani Trap for 100 mm India make of heavy approved quality complete with CI grating, including supply of all materials,labour and T&P etc. required for proper completion of the work.

Providing and fixing 100 mm dia white glazed "P" or "S" trap including cement concrete and all materials, labour cartage T&P etc.required for proper completion of the work.(For W.C.)

Providing and fixing soap dish chromium plated with brackets fixed to wooden cleats with brass screws including supply of all materials,labour and T&P etc.required for proper completion of the work. (CSI No. 27.19)

Providing and fixing in position 32 mm. dia P.V.C. flush pipe. for W.C. with unions, bends etc. including supply of all materials,labour and T&P etc.required for proper completion of the work. (CSI No. 27.13)

Providing and fixing in position 32 mm. dia P.V.C. WASTE PIPE FOR WASH BASIN. including supply of all materials,labour and T&P etc.required for proper completion of the work.

Providing and laying 110 mm dia SWR, PVC ( Finolex or equivalent ) pipe including cost of excavation, C.C etc including its jointing and connection, all materials, labour and T&P etc. required for proper completion of the work.

Providing and fixing 110 mm dia SWR, PVC ( Finolex or equivalent ) Bends including cost of all materials, labour and T&P etc required for proper completion of the work.

Providing and fixing 110 mm dia SWR, PVC ( Finolex or equivalent ) plain Tee including cost of all materials, labour and T&P etc required for proper completion of the work.

Supply & installation of electrical control panel of L&T or havells orequivalent make forsubmersible pump set/pumpset containing contractor relay condenser for1 H.P. pumpset single phase

Supply & installation of single phase submersible pump of 1 HP outlet 32 mm dia. or more, Head 78/30,Discharge 1100/2800 LPH of K.S.B. or equivalent make, including supply of all materials, labour and T&P etc. required forproper completion of the work with one year of warrenty of site.

Supply & fixing of submersible cable size 1.5 mm2 for pump set above one H.P. & less then 3 H.P. of havells equivalent make

Supply of 80 mm thick I shaped mechanically compressed inter locking cement concrete paver block manufactured by high pressure & controlled vibration machine having plan dimension 200X(160+120 mm) with minimum 5 mm thick toping of O.P.Cement mixed with 25% marble powder. The compressive strength of concrete pavers blocks shall not be less than 30 MPa & 4.5 Kg/No. including cost of all material, labour, T&P etc. required for proper completion of work as directed by Engineer-in-charge but excluding G.S.T. which shall be paid extra as per rules.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Wiring point for light with 1.0 sq.mm FR PVC insulated multistrand single core copper conductor cable in heavy duty (2 mm thick) PVC conduit concealed in wall complete with 1.5 sq.mm. FR PVC insulated multistrand copper conductor cable as earth wire drawn inside the conduit, 6amp. Piano type switch and ceiling rose / angle / batten holder on 3mm. thick phenolic laminated backelite- sheet etc. complete in all respect,as directed .

Wiring point for fan/fresh air fan (light duty exhaust fan) with 1 sq. mm. FR PVC insulated multistrand copper conductor cable in PVC conduit concealed in wall, complete with 1.5 sq.mm. FR PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit, Piano type switch and ceiling rose on 3mm. thick phenolic laminated backelite- sheet etc. complete in all respect,as directed .

Wiring point for plug with 1.0 sq.mm FR PVC insulated multistrand single core copper conductor cable in heavy duty (2 mm thick) PVC conduit concealed in wall complete with 1.5 sq.mm. FR PVC insulated multistrand copper conductor cable as earth wire drawn inside the conduit, 6amp. Piano type switch and 5pin socket etc.complete on 3mm. thick phenolic laminated backelite- sheet etc. complete in all respect,as directed .

Wiring point for exhaust fan with 1.5 sq.mm FR PVC insulated multistrand single core copper conductor cable in heavy duty (2 mm thick) PVC conduit concealed in wall complete with 1.5 sq.mm. FR PVC insulated multistrand copper conductor cable as earth wire drawn inside the conduit, 15amp. Piano type switch and ceiling rose / angle / batten holder on 3mm. thick phenolic laminated backelite- sheet etc. complete in all respect,as directed .

Supply and wiring of submains with 2 nos. 2.5 sq.mm & with 1 no earth continuity wire of 1.5 sq.mm FR PVC insulated 1100V grade insulated multistrand single core copper conductor cable in 20mm dia heavy duty (2mm thick) PVC conduit concealed in wall complete,including supply of all materials, labour and T&P etc.required for proper completion of the work.

Supply and wiring of submains with 2 nos. 4 sq.mm & with 1 no earth continuity wire of 2.5 sq.mm FR PVC insulated 1100V grade insulated multistrand single core copper conductor cable in 20mm dia heavy duty (2mm thick) PVC conduit concealed in wall complete,including supply of all materials, labour and T&P etc.required for proper completion of the work.

S/F of factory wired CFL street light having deep drawn M.S. housing with powder coated finish, alluminium reflector and acrylic cover suitable for and with 36 watt CFL lamp including G.I. pipe bracket complete in all respect on wall .

Supply and fixing of 6 to 32 Amp MCB (10 KA ) .

S/F of 63 Amp. T.P. Isolator

S/F of power plug with 15A/240V flush type switch and 5 pin 15A/250V flush type universal socket in suitable MS box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3 mm thick fixed with brass machine screw and cup washer.

S/F approved quality ceilling fan including cost of all material ,labour and T&P etc. for proper work of completion.

Supply and installation of LED Tube light Crompton, Bajaj & equivalent made with fitting of box / channel type T-5 energy saver without reflector & without end cover for one number 20 watt T-5 Lamp/Tube with 1x20 watt T-5 Lamp Tube complete all respect.

S/F of factory wired,HPF street light flourescent tube light fitting suitable for 1x40 watt flourescent tube complete including tube etc. on G.I pipe bracket complete in all respect.

Supply and Fixing of 3 blade wall fan of Havells platina 400 mm or equivalent including all material, T&P etc required for proper completion of work as approved by engineer in charge.

Supply and Fixing of 5 blade Exhaust fan ventile air dx 225 mm of Havells or equivalent make including all material, T&P etc required for proper completion of work as approved by engineer in charge.

SINGH ENTERPRISES