REPAIR/POLISHING/RECANNING OF WOODEN FURNITURE AT BARRACKPORE MIL STN UNDER GE BARRACKPORE

Amount

REPAIRS TO BED WITH PLY TOP FOR THE FOLLOWING (DRG No.FD-246):-

HEAD BOARD Removing decayed head board from its existing position and replace the same with new head board of overall size 900 x 610mm, frame made out from well seasoned 1st class hard wood (Teak/Seasam) batten 75mm x 22mm thick with soft wood (chair batten 03 Nos board), 4mm thick one side teak face BWR grade, type BB Ply wood (three Nos of ply) and other side commercial to be provided on both sides of the head board covering the soft wood batten, 12mm dia half cut teak wood beading shall be provided to join the ply wood and Hollock wood frame all as Shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved)

FOOT BOARD Removing decayed foot board from its existing position and replace the same with new foot board of overall size 900mm long and 300mm height, frame made out from well seasoned 1st class hard wood (Teak/Seasam) batten 75mm x 22mm thick with soft wood (chair batten 03 Nos board), 4mm thick one side teak face BWR grade, type BB Ply wood (three Nos of ply) and other side commercial to be provided on both sides of the foot board covering the soft wood batten, 12mm dia half cut teak wood beading shall be provided to join the ply wood and Hollock wood frame all as Shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply as approved)

LONG RAIL Removing of each decayed long rail from its existing position and replace the same with new well seasoned 1st class hard wood (Teak/Seasam) long rail of size 95mmx35mmx1980mm long rounded one edges or face made out from well seasoned wood all as shown on drawing.

SHORT RAIL Removing of each decayed short rail from its existing position and replace the same with new well seasoned 1st class hard wood (Teak/Seasam) short rail of size 95mmx35mmx900mm short rounded one edges or face made out from well seasoned wood all as shown on drawing.

HEAD BOARD OUTER S&F for new 4mm thick one side teak face BWR grade, type BB plywood (three Nos of ply) and other side commercial for head board outer including finishing the surfaces with french polish taking out unserviceable/damage "head board outer" complete all as specified and as shown on drawing. (Make of Ply wood : Century Ply/Green Ply/ National Ply/ Kit Ply as approved)

HEAD BOARD INNER S&F for new 4mm thick one side teak face BWR grade, type BB plywood (three Nos of ply) and other side commercial for head board inner including finishing the surfaces with french polish taking out unserviceable/damage "head board inner" complete all as specified and as shown on drawing. (Make of Ply wood : Century Ply/Green Ply/ National Ply/ Kit Ply as approved)

FOOT BOARD OUTER S&F for new 4mm thick one side teak face BWR grade, type BB plywood (three Nos of ply) and other side commercial for foot board outer including finishing the surfaces with french polish taking out unserviceable/damage "foot board outer" complete all as specified and as shown on drawing. (Make of Ply wood : Century Ply/Green Ply/ National Ply/ Kit Ply as approved)

FOOT BOARD INNER S&F for new 4mm thick one side teak face BWR grade, type BB plywood (three Nos of ply) and other side commercial for foot board inner including finishing the surfaces with french polish taking out unserviceable/damage "foot board inner" complete all as specified and as shown on drawing. (Make of Ply wood : Century Ply/Green Ply/ National Ply/ Kit Ply as approved)

STIFFENER Removing of each decayed stiffener from its existing position and replace the same with new well seasoned 1st class hard wood (Teak/Seasam) stiffener of size 60mmX40mmX880mm long rounded one edges or face made out from well seasoned wood all as shown on drawing.

MS FLAT IRON STIFFENER Removing old MS stiffener from hard bed and replace the same with MS flat iron of size 35mm x5mmx150mm, bent at right angle at four corner all as shown on drawing.

TOP Removing decayed/wornout ply wood top from its existing position and replace the same with new plywood top made out from 12mm thick plywood (seven Nos of ply), BWR grade, type BB fixed to wooden rails with screws all as shown on drawing. (Make of Ply wood : Century Ply/Greenply/National ply/Kit ply/Archid ply as approved)

POLISHING TO BED WITH PLY TOP Removal of old existing worn out polish from exposed portion of wooden surface by any means of bed with ply top including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras , burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge .

REPAIRS TO CHAIR DINING FOR THE FOLLOWING (DRG No.FD-16(M), FD-279):-

FRONT LEG Removing of each decayed front leg from its existing position and replace the same with new front leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

REAR LEG Removing of each decayed rear leg from its existing position and replace the same with new rear leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

FRONT RAIL Removing of each decayed front rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing .

REAR RAIL Removing of each decayed rear rail from its existing position and replace the same with new rear rail made out from well seasoned1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.

SIDE RAIL Removing of each decayed side rail from its existing position and replace the same with new side rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.

REAR STIFFENER Removing of each decayed rear stiffener from its existing position and replace the same with new rear stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

STIFFENER Removing of each decayed stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

HARD RUBBER/PVC RING Removing of each decayed hard rubber/PVC ring from its existing position of chair dinning (FD-161M, FD-279), Chair Writing (FD-280), Chair Easy (FD-281), FD-229) and replace the same with new hard rubber/PVC ring all as shown on drawing and directed by Engineer-in-Charge.

POLISHING TO CHAIR DINING Removal of old existing worn out polish from exposed portion of wooden surface by any means of chair dinning including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIR TO CHAIR WRITING FOR THE FOLLOWING (DRG No. FD-280):-

FRONT LEG Removing of each decayed front leg from its existing position and replace the same with new front leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

REAR LEG Removing of each decayed rear leg from its existing position and replace the same with new rear leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

FRONT RAIL Removing of each decayed front rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.

REAR RAIL Removing of each decayed rear rail from its existing position and replace the same with new rear rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.

SIDE RAIL Removing of each decayed side rail from its existing position and replace the same with new side rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.

REAR STIFFNER Removing of each decayed rear stiffener from its existing position and replace the same with new rear stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

STIFFENER Removing of each decayed stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

ARM Removing of each decayed arm from its existing position and replace the same with new arm made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

POLISHING CHAIR WRITING Removal of old existing worn out polish from exposed portion of wooden surface by any means of chair writing including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIRS TO CHAIR EASY FOR THE FOLLOWING (DRG NO.FD-281, FD-229):-

FRONT LEG Removing of each decayed front leg from its existing position and replace the same with new front leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

REAR LEG Removing of each decayed rear leg from its existing position and replace the same with new rear leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

FRONT RAIL Removing of each decayed front rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.

REAR RAIL Removing of each decayed rear rail from its existing position and replace the same with new rear rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing.

SIDE RAIL Removing of each decayed side rail from its existing position and replace the same with new side rail made out from well seasoned 1st class hard wood (Teak/Seasam) with 3mm dia hole at 12.5 mm c/c for weaving of plastic cane all as shown on drawing .

ARM Removing of each decayed arm from its existing position and replace the same with new arm made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

POLISHING TO CHAIR EASY Removal of old existing worn out polish from exposed portion of wooden surface by any means of chair easy including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIRS TO CHAIR WOODEN BOTTOM W/O ARM FOR THE FOLLOWING [DRG NO. FD-56(M), FD-225, FD-285] :-

FRONT LEG Removing of each decayed front leg from its existing position and replace the same with new front leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

REAR LEG Removing of each decayed rear leg from its existing position and replace the same with new rear leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

FRONT RAIL Removing of each decayed front rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing .

REAR RAIL Removing of each decayed rear rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing .

SIDE RAIL Removing of each decayed side rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing .

STIFFNER Removing of each decayed stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

SEAT Removing of decayed/wornout plywood seat from its existing position and replace the same with new seat made out from plywood of 6mm thick, BWR grade, type BB (five Nos of ply) trapezoidal in shape of length 445mm at front side and 405mm at rear side with 440mm in height all as shown on drawing.

POLISHING TO CHAIR WOODEN BOTTOM W/O ARM Removal of old existing worn out polish from exposed portion of wooden surface by any means of chair wooden bottom without arm including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge .

RECANNING OF VARIOUS TYPE OF CHAIRS FOR THE FOLLOWING (DRG NO.FD-279, FD-280, FD-281, FD-229) :- Removing of old unserviceable cane plastic from various chairs such as chair dining, chair writing, chair CB office, chair office CB, chair CB w/o arm and chair easy etc re-canning the same with new cane plastic 2mm wide half round white in colour for main canning and 3.5 to 4mm wide half round white in colour for border as approved quality all as shown on drawing.

REPAIRS TO LOCKER FOR THE FOLLOWING (DRG NO FD-54(M) , FD-222) :-

TOP Removing decayed wooden top of locker from its existing position and replace the same with new top made out from 18mm thick well seasoned 1st class hard wood (Teak/Seasam) plank complete all as shown on drawing.

BOTTOM Removing decayed wooden from bottom side of locker from its existing position and replace the same with new bottom made out from 18mm thick well seasoned 1st class hard wood (Teak/Seasam) plank complete all as shown on drawing.

SIDE Removing decayed wooden each side of locker from its existing position and replace the same with new side made out from 18mm thick well seasoned 1st class hard wood (Teak/Seasam) plank complete all as shown on drawing.

SHUTTER Removing decayed shutter (Single leaf) from its existing position and replace the same with new leaf made out from 18mm thick veneered particle board (exterior grade) one side teak finish with 6mm thick and 1st class hard wood (Teak/Seasam) beading all round the shutter all as shown on drawing.

BACK Removing decayed back from its existing position and replace the same with new back made out from 6mm thick ply wood (five Nos of ply), type BB, BWR grade all as shown on drawing.

SHELF Removing each decayed shelf from its existing position and replace the same with new shelf made out from 12mm thick well seasoned 1st class hard wood (Teak/Seasam) planks all as shown on drawing.

HANGING ROD Removing old broken hanging rod from its existing position and replace the same with new hanging rod made out from 20mm (external dia) aluminium anodized conduit with a pair of sockets all as shown on drawing.

LEG Removing decayed wooden each leg of locker from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) of size 50mmx50mm all as shown on drawing.

RAIL Removing decayed wooden each rail of locker from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) of size 25mmx40mm all as shown on drawing.

HANDLE S&F for 100mm long CP handle all as shown on drawing.

HINGES S&F for 75mm long cold rolled mild steel butt hinges (medium weight) fixed with steel screws all as shown on drawing.

HASP & STAPLE Supply and fixing for 75mm long hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with steel wood screws.

POLISHING TO LOCKER Removal of old existing worn out polish from exposed portion of wooden surface by any means of locker including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIRS TO TRESTLE STORE ROOM WOODEN FOR THE FOLLOWING [DRG NO FD-86(M),FD-141]:-

LEG Removing of decayed each leg of trestle store room from its existing position and replace the same with new leg made out from well seasoned ‘SAL’ wood all as shown on drawing.

TOP LONG RAIL Removing of decayed top long rail from its existing position and replace the same with new long rail made out from well seasoned ‘SAL’ wood all as shown on drawing.

CROSS STIFFENER Removing of decayed cross stiffener from its existing position and replace the same with new cross stiffener made out from well seasoned ‘SAL’ wood all as shown on drawing.

INTERMEDIATE STIFFENER Removing of decayed intermediate stiffener from its existing position and replace the same with new intermediate stiffner made out from well seasoned ‘SAL’ wood all as shown on drawing.

POLISHING TO TRESTLE STORE ROOM WOODEN Removal of old existing worn out polish from exposed portion of wooden surface by any means of locker including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIRS TO TABLE WRITING FOR THE FOLLOWING (DRG NO. FD-33, FD-249, FD-275) :-

LEG Removing decayed each leg of table writing from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP RAIL Removing decayed each top rail of table writing from its existing position and replace the same with new top rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

BOTTOM RAIL Removing decayed each bottom rail of table writing from its existing position and replace the same with new bottom rail made out from well 1st class hard wood (Teak/Seasam) all as shown on drawing.

STIFFENER Removing decayed each stiffener of table writing from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

SIDE BOX WITH DRAWER Removing decayed side almirah (side box ) with drawer and replace the same with 18mm thick veneered particle board (exterior grade) made having teak face at one side and other side commercial for side, back , front and bottom side of the drawer, stiffener, bearer shall be made out from well seasoned second class hardwood, rest all as shown on drawing.

TOP Removing decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior Grade), prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging all as shown on drawing.

POLISHING TO TABLE WRITING Removal of old existing worn out polish from exposed portion of wooden surface by any means of table writing including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge .

REPAIRS TO TABLE 3’X2’ W/O DRAWER FOR THE FOLLOWING [DRG NO. FD-284, FD-55, FD-42(M)]:-

LEG Removing decayed each leg from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP RAIL LONG Removing decayed each top long rail from its existing position and replace the same with new long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP RAIL SHORT Removing decayed each top short rail from its existing position and replace the same with new short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

STIFFENER Removing decayed each stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP Removing decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior Grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffener at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.

POLISHING TO TABLE 3'x2' W/O DRAWER Removal of old existing worn out polish from exposed portion of wooden surface by any means of table 3'X2' without drawer including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge .

REPAIRS TO TABLE 3’X2’ WITH DRAWER FOR THE FOLLOWING [DRG NO. FD-283, FD-41(M) ]:-

LEG Removing decayed each leg from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP RAIL LONG Removing decayed each top long rail from its existing position and replace the same with new long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP RAIL SHORT Removing decayed each top short rail from its existing position and replace the same with new short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

STIFFENER Removing decayed each stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP Removing decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior Grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffener at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.

DRAWER Removing decayed and replace the drawer made out from well seasoned 1st class hard wood (Teak/Seasam) for front, rear & side with track rail, guide rail & fillet and bottom shall be made out from 6mm thick plywood (five Nos of ply), type BB, BWR grade complete all as shown on drawing.

POLISHING TO TABLE 3'x2' WITH DRAWER Removal of old existing worn out polish from exposed portion of wooden surface by any means of table 3'X2' with drawer including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge .

REPAIRS TO TABLE DINING FOR 6 PERSONS FOR THE FOLLOWING (DRG NO. FD-30, FD-239, FD-273) :-

LEG Removing decayed each leg from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP RAIL LONG Removing decayed each top long rail from its existing position and replace the same with new long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP RAIL SHORT Removing decayed each top short rail from its existing position and replace the same with new short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

STIFFENER Removing decayed each stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP Removing decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior Grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffener at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.

HARD RUBBER/PVC RING Removing of each decayed hard rubber/toe from its existing position and replace the same with new hard rubber/PVC toe 25mm dia and 25mm high all as shown on drawing and directed by Engineer-in-Charge.

POLISHING TO TABLE DINING FOR 6 PERSONS Removal of old existing worn out polish from exposed portion of wooden surface by any means of table dinning for 6 person including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIRS TO TEAPOY FOR THE FOLLOWING (DRG NO.FD-34, FD-232, FD-382, FD-278):-

LEG Removing decayed each leg from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP RAIL LONG Removing decayed each top long rail from its existing position and replace the same with new long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP RAIL SHORT Removing decayed each top short rail from its existing position and replace the same with new short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

STIFFENER Removing decayed each stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP Removing decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior Grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffener at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.

POLISHING TO TEAPOY Removal of old existing worn out polish from exposed portion of wooden surface by any means of teapoy including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIRS TO TABLE CENTRE FOR THE FOLLOWING (DRG NO.FD-29 , FD-235, FD-274):-

LEG Removing decayed each leg from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP RAIL LONG Removing decayed each top long rail from its existing position and replace the same with new long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP RAIL SHORT Removing decayed each top short rail from its existing position and replace the same with new short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

STIFFENER Removing of each decayed stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP Removing decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior Grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffener at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.

POLISHING TO TABLE CENTRE Removal of old existing worn out polish from exposed portion of wooden surface by any means of table centre including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIRS TO TABLE DRESSING GENTS FOR THE FOLLOWING (DRG NO.FD-230, FD-379):-

TOP AND BOTTOM OF BOX Removing decayed top and bottom of box from its existing position and replace the same with new top made out from 12mm thick pre-laminated particle board (exterior grade), grade-I quality, with 6mm thick and well seasoned 1st class hardwood (Teak/Seasam) wooden beading allround the edging. Bottom of the box shall be made out 12mm thick ply wood (seven Nos of ply), type BB, BWR Gde complete all as shown on drawing.

SIDE OF BOX Removing decayed each side of the box from its existing position and replace the same with new side of the box made out from 12mm thick pre-laminated particle board (exterior grade), grade-I quality, one side decorative all as shown on drawing.

BACK OF BOX Removing decayed each back of the box from its existing position and replace the same with new back of the box made out from 12mm thick plywood (seven Nos of ply), type BB, type BWR grade, complete all as shown on drawing.

DRAWER Removing decayed drawer and supply and fixing drawer front & side made out from 12mm thick pre-laminated particle board (exterior grade), grade-I quality, one side decorative, bottom shall be made out from 6mm thick ply wood (five Nos of ply), type BB, BWR grade and back shall be made out from 12mm thick well seasoned second class hardwood all as shown on drawing.

MIRROR Removing broken mirror from its existing position and supply and fixing for copper plated 5.5mm thick mirror mounted on new frame made out 6mm thick ply wood (five Nos of ply), type BB, BWR grade and with well seasoned second class hard wood all as shown on drawing. (Make : Modiguard/Saint gobain as approved)

POLISHING TO TABLE DRESSING GENTS Removal of old existing worn out polish from exposed portion of wooden surface by any means of table dressing gents including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge .

REPAIRS TO TABLE DRESSING LADIES FOR THE FOLLOWING (DRG NO.FD-251) :-

TOP Removing decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior Grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffener at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.

SIDE Removing decayed side from its existing position and replace the same with new side made out from 18mm thick veneered particle board (exterior grade) with one face teak and other face commercial veneer all as shown on drawing.

BACK Removing decayed side from its existing position and replace the same with new side made out from 12 mm thick veneered particle board (exterior grade) with commercial veneers on both faces all as shown on drawing.

DRAWER Removing drawer and replace the side and back of drawer made out from 12mm thick well seasoned 1st class hard wood (Teak/Seasam). Bottom of the drawer shall be made out from 6mm thick ply wood (five Nos of ply), type BB, BWR grade. Front of the drawer shall be made out from 18mm thick veneered particle board (exterior grade) with commercial veneers on both faces with 1.00mm thick plastic laminated sheet (plain & wood grain) pasted over particle board with approved synthetic adhesive all as shown on drawing.

MIRROR Removing broken mirror with frame and supply and fixing for mirror 5.50 mm thick 355mmx1220mm size free from any cracks/scratches and distorted image etc mounted on 6mm thick ply wood (five Nos of ply), type BB, BWR grade and with 25mmx19mm teak wood well seasoned timber frame all as shown on drawing. (Make : Modiguard/Saint gobain as approved)

POLISHING TO TABLE DRESSING LADIES Removal of old existing worn out polish from exposed portion of wooden surface by any means of table dressing ladies including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge .

REPAIR TO TABLE 900MMX900MM FOR THE FOLLOWING (DRG NO.FD-88, FD-291):-

LEG Removing decayed each leg of table 900mmx900mm from its existing position and replace the same with new leg made out well seasoned 1st class hard wood (Teak/Seasam) all as shown in drawing.

SIDE RAIL LONG Removing each decayed side rail long from its existing position and replace the same with new side rail long made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown in drawing.

SIDE RAIL SHORT Removing each decayed side rail short from its existing position and replace the same with new side rail short made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown in drawing.

TOP Removing decayed top from its existing position and replace the same with new 18/19mm thick Prelaminated Particle board (exterior Grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination including provision of 4mm thick teak wood beading alround the edging all as shown on drawing.

MS STIFFENER Provision of mild steel flat iron of size 20mmx3mmx200mm long bent to shape as in strap to all joints, jointing length & top of each table fixed with suitable size wood screws all as directed.

POLISHING TO TABLE 900MM X 900MM Removal of old existing worn out polish from exposed portion of wooden surface by any means of table (900mmX900mm) including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge .

REPAIR TO TABLE BED SIDE FOR THE FOLLOWING (DRG No FD-276, FD-248, FD-28, FD-210):-

TOP Removing decayed top from its existing position and replace the same with new 18/19mm thick Prelaminated Particle board (exterior Grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination including provision of 4mm thick teak wood beading alround the edging all as shown on drawing.

LEG Removing decayed wooden each leg of table bed side from its existing position and replace the same with new leg made out from well seasoned 1st class hard wood (Teak/Seasam) of size 65mmx50mm all as shown on drawing.

BACK Removing decayed each back of table bed side from its existing position and replace the same with new back made out from 6mm thick plywood (five Nos of ply), type BB, BWR grade of required size all as shown on drawing.

SIDE Removing decayed each side of table bed side from its existing positon and replace the same with 18mm thick one side teak face particle board (Exterior Grade), grade-I quality of required size all as shown on drg.

POLISHING TO TABLE BED SIDE Removal of old existing worn out polish from exposed portion of wooden surface by any means of table bed side including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge .

REPAIRS TO TABLE PEG FOR THE FOLLOWING (DRG NO.FD-25, FD-236, FD-277, FD-384):-

LEG Removing decayed each leg of table 900mmx900mm from its existing position and replace the same with new leg made out well seasoned 1st class hard wood (Teak/Seasam) all as shown in drawing.

TOP SHORT RAIL Removing decayed each top short rail from its existing position and replace the same with new short rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP LONG RAIL Removing decayed each top long rail from its existing position and replace the same with new long rail made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

STIFFENER Removing of each decayed stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

TOP Removing decayed top from its existing position and replace the same with new top made out from 18/19mm thick Prelaminated Particle board (exterior Grade), grade-I quality, prelaminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak/Seasam) beading allround the edging provide middle stiffener at the bottom 100mm high between the lower short side rails and provide PVC shoes 25mm dia and 25mm high shall be screwed to bottom of all legs all as shown on drawing.

POLISHING TO TABLE PEG Removal of old existing worn out polish from exposed portion of wooden surface by any means of table peg including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIRS TO SIDE BOARD FOR THE FOLLOWING (DRG NO FD-26, FD-372, FD-241, FD-371):-

Removing decayed top from its existing position and replace the same with new veneered particle board 18mm thick (exterior grade), grade-I quality, with 1.00mm thick plastic laminated sheet plain & wood grain pasted over particle board with approved synthetic adhesive all as shown on drawing.

Removing decayed back form its existing position and replace the same with new 6mm thick plywood (five Nos of ply), type BB, BWR grade complete all as shown on drawing.

Removing decayed shutter (single leaf) from its existing position and replace the same with 18mm thick veneered particle board (exterior grade), grade-I quality with one face teak veneer and other side commercial and 6mm thick well seasoned 1st class hard wood (Teak/Seasam) beading alround the shutter all as shown on drawing.

Removing decayed each side of side board from its existing position and replace the same with 18mm thick veneered particle board(exterior grade), grade-I quality with one face teak veneer all as shown on drawing.

Removing decayed drawer and replace the drawer made out from 18mm thick veneered particle board (exterior grade) grade-I quality, with one face teak veneer on front side and 6mm thick plywood (five Nos of ply), type BB, BWR grade on botton knob for the drawer shall be provided as approved by Engineer-in-Charge and rest all as shown on drawing.

POLISHING TO SIDE BOARD Removing of old existing wornout polish from exposed portion of wooden surface by sand paper and preparation of new surface smooth for further new polishing (Including scoring out all previous marking, numbering ) and polishing all exposed portion by spirit polish mixed with shellac gde-I, chandras, burnt saina, raw saina, sindur etc to obtain high gloss finishing upto the full satisfaction of Engineer-in-charge.

TAKING DOWN OLD UNSERVICEABLE COMPONENTS/PARTS FROM SOFA SET (5 SEATER/ 4 SEATER/3 SEATER & SINGLE SEATER) AND RE-ASSEMBLE/REFIXING WITH THE FOLLOWING NEW PARTS MADE OUT OF WELL SEASONED TEAK WOOD FREE FROM CRACK, KNOTS, HOLE ETC ALL ASS SPECIFIED AND SHOWN ON ( DRGS NO. FD-281):-

S&F for teak wood arms of sofa sets of required size including taking out unserviceable/damage "arms" complete all as specified and as shown on drawing.

S&F for teak wood legs of sofa sets of required size including taking out unserviceable/damage "legs" complete all as specified and as shown on drawing.

S&F for teak wood bottom of seat & back of sofa sets of required size including taking out unserviceable/damage "bottom of seat & back" complete all as specified and as shown on drawing.

S&F for teak wood front/rear rails of sofa sets of required size including taking out unserviceable/damage "front/rear rails" complete all as specified and as shown on drawing (Long pieces).

S&F for teak wood side rails of sofa sets of required size including taking out unserviceable/damage "side rails" complete all as specified and as shown on drawing.(3 seater & single seater).

REPAIR/REPLACEMENT OF FOAM CUSHION OF CHAIR DINING OFFICER (DRG NO.FD/MAP-II/04):-

Removal of old unserviceable foam, cushion of chair dining officers set (comprising of 06 Nos single cushion of seat) and supply and fixing new foam cushion 75mm thick, 450mm x 450mm, 40/32 density, covered with approved quality tapestry cloth (cost of tapestry cloth shall not be less than Rs. 200.00 per metre) and rest all as per Drawing/Directed by Engr-in-charge

STIFFNER Removing decayed each stiffner from its existing position and replace the same with new stiffner made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

POLISHING TO CHAIR DINING OFFICER Removal of old existing worn out polish from exposed portion of wooden surface by any means of sofa set five seater including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIR/REPLACEMENT OF FOAM CUSHION OF SOFA SET 05 SEATER (DRG NO.FD-281):-

Removal of old unserviceable foam, cushion sofa set(comprising of 10 Nos single cushion including seat and back) and supply and fixing new foam cushion 100mm thick 40/32 density covered with approved quality tapestry cloth (cost of tapestry cloth shall; not be less than Rs.450.00 per metre). (Make : Kurlon/Sleepwell as approved)

Removal of old unserviceable tapestry cloth from each foam cushion sofa set (comprising of 10 Nos single cushion) and replace with new tapestry cloth of approveds quality (cost of tapestry cloth shall not be less than Rs. 450.00 per metre).

POLISHING TO SOFA SET FIVE SEATER Removal of old existing worn out polish from exposed portion of wooden surface by any means of sofa set five seater including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIR/REPLACEMENT OF FOAM CUSHION OF SOFA SET 04 SEATER (DRG NO.FD-281):-

Removal of old unserviceable foam, cushion sofa set(comprising of 08 Nos single cushion including seat and back) and supply and fixing new foam cushion 100mm thick 40/32 density covered with approved quality tapestry cloth (cost of tapestry cloth shall; not be less than Rs.450.00 per metre). (Make : Kurlon/Sleepwell as approved)

Removal of old unserviceable tapestry cloth from each foam cushion sofa set (comprising of 08 Nos single cushion) and replace with new tapestry cloth of approveds quality (cost of tapestry cloth shall not be less than Rs. 200.00 per metre).

POLISHING TO SOFA SET FOUR SEATER Removal of old existing worn out polish from exposed portion of wooden surface by any means of sofa set five seater including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIRS TO CHAIR DINING FOR THE FOLLOWING (DRG NO : FD-MAP-II/05)

FRONT LEG Removing of each decayed front leg from its existing position and replace the same with new front leg made out from well seasoned 1st class hard wood (Teak/Seasam) all as shown on drawing.

REAR LEG Removing each decayed rear leg from its existing position and replace the same with new rear leg made out from well seasoned 1st class hard wood (Teak / Seasam) al as shown drawing.

FRONT RAIL Removing of each decayed front rail from its existing position and replace the same with new front rail made out from well seasoned 1st class hard wood (Teak / Seasam) all as shown on drawing.

REAR RAIL Removing of each decayed rear rail from its existing position and replace the same with new rear rail made out from well seasoned 1st class hard wood (Teak / Seasam) all as shown on drawing.

REAR STIFFENER Removing of each decayed rear stiffener from its existing position and replace the same with new rear stiffener made out from well seasoned 1st class hard wood (Teak / Seasam) all as shown on drawing.

STIFFENER Removing of each decayed stiffener from its existing position and replace the same with new stiffener made out from well seasoned 1st class hard wood (Teak / Seasam) all as shown on drawing.

HARD RUBBER / PVC RING Removing of each decayed hard rubber / PVC ring from its existing position of Chair dinning and replace the sme with new hard rubber / PVC ring all as shown on drawing and directed by Engineer-in-Charge.

SEAT Removing of decayed / wornout PVC seat from its existing position and replace the same with new seat of size 4mm x 10mm thick ribs molded long with single frame all as show on drawing and directed by Engineer-in-Charge. (Make:Brite/Cello/Supreme/Nilkamal as approved)

POLISHING TO CHAIR DINING Removal of old existing worn out polish from exposed portion of wooden surface by any means of sofa set five seater including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

REPAIRS TO TABLE DINING 1200X900MM FOR THE FOLLOWING (DRG NO : FD/MAO-II/03):-

TOP Removing of decayed top from its existing position and rreplace the same with new top made out from 18/19mm thick prelaminated particle board (exterior grade), Grade-I quality, prelaminated one side with decorative choice lamination and other side balancing white lamination with 6mm thick and well seasoned 1st class hard wood (Teak / Seasam) beading all-round the edging complete all as shown on drawing and as directed by Engineer-in-Charge. (Make of Plywood : Century ply/Green ply/National ply/ Kitply as approved)

HARD RUBBER / PVC RING Removing of each decayed hard rubber / toe from its existing position of table dining and replace the same with new hard rubber / PVC toe 25mm and 25mm high all as shown on drawing and directed by Engineer-in-Charge.

POLISHING TO TABLE DINING 1200X900MM Removal of old existing worn out polish from exposed portion of wooden surface by any means of sofa set five seater including preparation of new wooden members by sand papering and making the furniture completely smooth for further new polishing (including scoring out all previous marking, numbering) and apply polishing to all the exposed surface by spirit polish mixed with shellac Gde-I, chandras, burnt saina, raw saina, sindur etc till glossy surface is obtained upto the full satisfaction of the Engr-in-Charge.

M/S NEHAL ENTERPRISES

TIMBA

REMCO

TAMALIKA ENTERPRISE

SANKAR TRADERS

Kiran Traders

MAZUMDER AND CO

SHARMA CONSTRUCTION

B N ENTERPRISE

M/S. QUANTAMBUILD SOLUTIONS(OPC) PRIVATE LIMITED