CA NO CWE BLY/GE(E)/02 OF 2021-22 PROVN OF GUARD ROOM WITH TOILET AND DISPENSARY AND PATIENT WAITING HALL AT GARUD FAMILY HEALTH CLINIC UNDER GE (EAST) BAREILLY

Amount

Excavation in trenches not exc. 1.50 m wide and not exc. 1.50 m in depth for foundation etc. or for manholes, cesspits, shafts etc. not exc. 10 Sqm on plan and getting out in hard/ dense soil complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard/ dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing excavated soil to distance n.exc. 50m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

M&L for providing plain cement concrete, type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for RCC M25 Design mix as in foundations, inclduing raft, footing, foundation beam, under ramed piles and mass concrete complete all as specified and directed.

M&L for RCC M25 Design mix as in beams, lintel beams over 1.50 meter span,cantilevers, bressummers etc complete all as specified and directed.

M&L for RCC M25 Design mix as in chajjas omplete all as specified and directed.

M&L for RCC M25 Design mix as in columns, piers, posts etc complete all as specified and directed.

M&L for RCC M25 Design mix as in slab supported on walls, beams and columns in floor, roof, landing, balconies etc complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spaces and binders , cut to length , bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality conforming to complete all as specified.

M&L for form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for form work to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar work n.exc. 200 mm thick curved (horizontal or sloping ) work in rough finished flat surfaces of concrete complete all as specified and directed.

M&L for form work to sides and soffits of floor or roof beams, beam haunchings,girders, ressummers, lintels, cantilevers, shelves including supports,overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

S&F form work to sides chulla hoods,chajjas,troughs and similar items including edges complete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window ills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M & L for treating the top surface of filled earth of floor and plinth protection at the rate of 5 litres of emulsion per square metre of surfacecomplete all as specified and directed.

M & L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and directed.

M & L for Treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wallcomplete all as specified and directed.

M&L for brick work with fly ash bricks straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L Hard core of guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface complete all as specified and directed.

M& L 100 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed

M& L 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base floor / pavings complete all as specified and directed

M & L 25 mm thick PCC (1:2:4) type B1(20 mm graded aggregate) as in floor rough finished to receive top layer complete all as specified and directed..

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, for laying floor finishes/tiles complete all as specified and directed.

M&L Screed bed or bedding layer 20mm thick in CM 1:4 for laying glazed tiles in floors etc. complete all as specified and as directed

M&L 15mm thick rendering in cement mortar 1:4 to brick masonry wall surfaces or on other than fair faces of brick wall surfaces finished fair & even without using extra cement for fixing tiles etc complete all as specified and directed

M&L vitrified ceramic dark shade/double charged/ultra charged tiles 10mm thick (square / rectangular) area of each tile exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile complete all as specified and directed.

M & L 7 to 8 mm thick glazed coloured ceramic tiles ( square/ rectangular) with border, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L 20 mm thick Granite of any colour (table rubbed and polished) as in windows cill , in steps, jambs, pillars, cooking platforms, wall lining and like set in cement mortar (1:4) including form work , pointing in white cment (1:2) using marble dust with admixture of pigment to match with shade of granite with full round bull nosing edging complete all as spd as directed

M&L for sand filling under floors or in foundation, including watering and consolidation complete all as specified and as directed.

M&L for cement Concrete coloured interlocking paver blocks factory made with casting in rubber/PVC moulds & compacting on a vibro table assembly and shall be cured in curing tank for atleast 14 days and then air dried before use. The paver block shall be confirming to IS 15658 -2006 of 60mm thickness, M-35 Grade. Approved design, shape, size and colour of top layer complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6, type C1, with using 20 mm graded stone aggregate as in plinth protection, finish the surface even and smooth without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 mtr and every change of direction and filling the same with bitumen filler/filler boards 1:3 by weight complete all as specified and directed.

S&F sliding window of aluminium alloy powder coated window frame with movable shutter (sliding on minimum two PVC rollerof best quality for each shutter) on tracks (three tracks with mosquito proofing) and glazing with and including 5 mm thick tinted glass fixed withneoprene rubber gasket with aluminium beading, clips frame made with aluminium section as appended below complete all as specified and directed. (a) window frame 63x35x1.48mm thick with rawl plug (b) Middle and lock rail : 150x44x1.48mm thick for three tracks (c) Top/Bottom rail and style of shutter : 19x38x1.48mm thick (d) Aluminium beading : 0.7mm thick (e) Stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window. (f) Aluminium handle 100mm long. (g) Making good of wall surface to match with existing surface complete.

S&F aluminium alloy powder coated ventilators box type with louvers and wire mesh fixed withneoprene rubber gasket with aluminium beading, clips frame made with aluminium section as appended below complete all as specified and directed. (a) Frame 45.2x35x1.15mm thick with rawl plug (b) Aluminium beading : 0.7mm thick (c) Glass louvers 3mm thick and 150mm wide, blade angle 38 degree with 106.25mm spacing. (d) Stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed. (e) Aluminium fittings as required. (f) Making good of wall surface to match with existing surface complete.

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing fixed with and including 5.50 mm thick tinted glass fixed with rubber gasket with aluminium heading, clips frame made with aluminium box section as appended below complete all as specified and directed (a) Frame 100x44x1.48mm thick with rawl plug (b) Middle and lock rail : 150x44x1.48mm thick (c) Bottom rail : 150x44x1.48mm thick (d) Top rail/style : 85x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver, aluminium stopper, cleat, double action floor spring hydraulically regulated made not less than 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass and other parts steel heavy duty.(make Sandhu ISI marked or equivalent) (g) Making good of wall surface to match with existing surface complete.

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing fixed with and including 5 mm thick aluminium composite panel LDPE core PET coating ( both side decorative type ) fixed with rubber gasket with aluminium heading, clips frame made with aluminium box sec as appended below complete all as specified and directed (a) Frame 100x44x1.48mm thick with rawl plug (b) Middle and lock rail : 150x44x1.48mm thick (c) Bottom rail : 150x44x1.48mm thick (d) Top rail/style : 85x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver , with S S hinges complete (g) Making good of wall surface to match with existing surface complete.

S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy type curtain rod with decorative design matching brackets as approved and knobs (lattu) or end bracket as required & other all neccesary fittings fitted with SS screws etc on each end complete all as specified and as directed. .

S&F 18mm thick termite resistant and water proof, both side prelaminated ply wood one side with decorative choice lamination and other side plain white lamination as in cup board shutters, with wardrobe/finch lock and PVC lipping on exposed edges of same texture and shade complete all as specified and directed. Note:- (a) Design and layout of wardrobe and pattern/colour of lamination shall be approved by GE. (b) Thickness of lamination not less than 1mm for inside plain white and 1.5mm for outer lamination. (c) Frame shall be fixed to wall, soffits of slab with fastners.

S&F in repair PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fittingcomplete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 110 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

M&L for bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for brushing neat cement slurry over existing roof surface with 3.0kg of cement per sq. metre using liquid water proofing @ 0.15 ltr per 50 kg bag of cement complete all as specified and directed.

Supply only liquid water proofing

M&L screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:4, over RCC roof slab for laying water proofing treatment using liquid water proofing @ 0.15 ltr per 50 kg bag of cement laying floor finishes/tiles complete all as specified and directed.

M&L rendering 15mm thick on other than fair of faces brick work in CM 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick on fair faces of brick work or concrete external surfaces in CM 1:4, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling of fair faces of concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of plastic emulsion paint over a coat primer complete all as specified and directed.

M&L for preparation of new plaster surfaces and applying two coats of oil bound distemper over a coat of primer on ceiling complete all as specified.

M&L for preparation of newly plastered surfaces and apply two coats of cement base paint over a coat of primer complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put togetherwith glue pinned at joints, supplied and fixed

S&F of 35 mm of second class hard wood Glazed and and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkats all as specified and directed.

S&F stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm, fixed with tinned tacks or galvanized wire staples complete all as specified and directed.

S&F 40mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Factory made solid panel PVC prelam colour door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 100mm long butt hinges extruded aluminium alloy with galvanised mild steel hinge pin anodised and fixed type C-21 complete all as specified and directed.

S&F aluminium handles,cast type,anodised 150mm size complete all as specified and directed.

S&F for ISI marked 150mm long aluminium alloy, anodized,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudedsections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F for ISI marked 300mm long aluminium alloy, anodized,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extrudedsections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 150mm long extruded Aluminium anodised,barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 200mm long extruded Aluminium anodised,barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 375mm long brass, rat tailed rod pattern spring including roller and roller plate welded to mild steel frame.fixed in repair complete all as spd & directed.

M & L for 7 to 8 mm thick non skid coloured ceramic tiles ( square/ rectangular) with border, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floor set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed.

M&L for machine cut mirror polish kota stone slab flooring 20-25mm thick over cement screed bed laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete as specified and as directed.

M&L for machine cut mirror polish kota stone slab 20-25mm thick as in riser of steps, skirting, dado and pillar laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete as directed.

S&F GI tubing of 15 mm dia, medium grade with all fittings and fixed to walls or ceiling or laid in floors complete all as specified and directed.

S&F GI tubing of 20 mm dia, medium grade with all fittings and fixed to walls or ceiling or laid in floors complete all as specified and directed.

S&F of vitreous china table top wash basin of suitable size including SS bottle trap, HDPE waste pipe including fixing on counter with SS waste coupling complete all as specified and directed. Make- Hindware cat No. 91072 model Orchid/ Parryware Cat No C0483/Cera Cat No. FLS-WHT-0575

S&F of vitreous China squatting pan Orissa pattern size 580 X 440 mm with integral foot rest white (excluding flushing cistern and flush pipe) including connection to drain or out going pipe and flush pipe anti syphonize pipe etc complete all as specified and dircetd.

S&F 10 ltrs PVC valveless syphonic action type flushing cistern low level white , with inlet ball valve, float and handle including bracket with 32 mm dia PVC pipe 600 mm long complete all as specified and as directed.

S&F 600mmx450mm bevelled edges mirror consisting of 6mm thick commercial plywood and fixed to plug with chromium plated brass screwed and cup washer

S&F fancy type sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with CP brackets, guard and railing 60cm long complete all as specified.

S&F CP towel rail 600mm long, 20mm dia, D type fixed with and including CP brass screws complete all as specified.

S&F fancy type 150mm size square brass CP shower rose complete all as specified.

S&F fancy type bib taps 15 mm dia chromium plated with wall flange cast copper alloy with capaston head screwed down for iron pipe or brass ferrule and fixed complete

S&F of 15mm bore of dia concealed stop cock cast copper alloy screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe all as specified and directed.

S&F angle cock 15mm bore chromium plated fancy type screwed down high pressure with crutch or butterfly handles screwed both ends for iron pipe or for union and fixed complete all as specified and directed.

S&F PVC connection 15mm bore length not less than 600 mm long with both ends PTMT nuts complete all as specified.

S&F of 15mm Pillar tap swan neck fancy type of cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and flynets screwed for iron pipe and fixed as directed.

S&F cast iron Nahani trap with grating including jointing to wate pipe fixed in cement concrete type B-1 (1:2:4) of 75mm bore complete all as specified.

M&L PVC (SWR) gully trap 125X110mm setting in jointing with solvent cement all as specified and directed.

S&F in repair PVC (SWR) 75mm bore pipes single socketed in any length with rubber ring joints fixed to wall and floor with necessary fittingcomplete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radius complete all as specified and directed.

S&F PVC (SWR) 75 mm bore junction single (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F 1000 litre rotational moulded polyethlene tripple layered water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

S&F 20mm bore Gun-metal globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed.

S&F 15 mm dia Ball valves ,high pressure with polythene float and flynut PTMT complete screwed for iron pipe or brass ferrule all as specified and directed.(minimum weight 142 grams)

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over 1mm thick wall care putty complete all as specified and directed.

M&L for preparation of new plaster surfaces and applying three coats of white wash on ceiling complete all as specified.

M&L applying two coats of synthetic enamel paints on new steel surfaces of any description over 10cm width or girth over a coat of red oxide primer including preparation of surfaces all as specified and directed.

M&L applying two coats of synthetic enamel paints on new wooden surfaces of any description over 10cm width or girth over a coat of pink primer including preparation of surfaces all as specified and directed.

M&L for 150mm bore RCC pipes class NP2 laid in trenches and jointed as specified.

M&L for concrete bed to drain pipes in cement concrete 1:3:6 type C-2 including packing under and haunching against the sides of pipes after they are laid and tested bore of pipe 150 mm complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as requiredbore of pipe 150 mm complete all as specified and directed.

E/M Part:- M&L for point wiring with 1.5 sqmm cable PVC unsheathed and insulated copper multistranded conductor FRLS 1100 Volts grade cable (red colour cable to be used for live connection and black colour cable to be used for neutral connection) controlled by one way switch drown through and including PVC concealed conduit with all accessories including 1.0 sqmm copper multistrand conductor FRLS 1100 Volts grade unsheathed PVC insulated (green colour) continuity earth wire connected to common earth dolly and sunk cast pressed steel terminal box made out of MS sheet 1.25 mm thick for mounting of fittings like switch , socket and fan regulator with 3 mm thick hylum laminated sheet cover incl cutting Chases pinning in, for concealed conduit wiring and making goods of disturbed surface not exc 15 cm girth complete all as specified and as directed for one light/fan/bell point controlled by one switch/bell push complete all as specified and directed.

All as per item No 101 here-in-before but for 3 pin 5 Amps socket outlet point controlled by one switch on same board

All as per item No 101 here-in-before but for 3 pin 5 Amps socket outlet point controlled by one switch on independent board

All as per item No 101 here-in-before but 2.5 Sqmm PVC insulated seathed cable and 2.5 Sqmm cable for earth wire for one 5 pin socket out let 15Amp.

S&F switch piano flush type polycarbonate 5 A single pole one way complete all as specified and directed.

S&F switch piano flush type polycarbonate 15 A single pole one way complete all as specified and directed.

S&F socket outlet polycarbonate 2 in 1, 3 pin Amps 5 pin multipurpose flush type complete all as specified and directed.

S&F socket outlet polycarbonate 2 in 1, 3/5 pin 5/15 Amp multipurpose flush type complete all as specified and directed.

S&F Lamp Holder PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F lamp LED lamp 9 watt, 230 volt complete all as specified and directed.

S&F of ceiling rose PVC polycarbonate, isolated body, 3 terminals AC 230 volt complete all as specified and directed.

S&F ultra slim LED MS batten light fitting, 1 x 20 watt powder coated decorative end cap complete with retrofit poly carbonate glass tube 4' long including electric connection with three core flexible PVC insulated copper conductor multistranded cable of 1.0 sqmm from ceiling rose to batten complete all as specified and directed.

S&F security light fitting, LED type, 25 watt, IP-65 pressure die cast housing with prismatic polycarbonate diffuser & individual LEDs as light source with integrated electronic driver complete with M&L GI pipe mounting bracket of size 25/32 mm dia and 2 m long bend including nut, bolts and 2 Nos GI clamps of size 50 x 6 mm as required and making connection with three core 1 sqmm copper conductor cable complete all as specified and directed.

S&F ceiling fan 1200mm sweep complete with all accessories such as rubber reel, split pins, check nuts, fan blades, PVC conopy, fan clamps, capacitor, PVC connector etc. and suitable electric connection with three core flexible PVC in sulated copper conductor (multistranded) cable of 1.0 Sqmm from ceiling rose to fan complete all as specified and directed.

S&F of exhaust fan 300 mm sweep, PVC body, AC 230 volts with louvres including making suitable size hole in the wall for air flow and grouting of nuts, bolts and washers including electric connection with three core flexible PVC insulated copper conductor multistranded cable of 1.0 sqmm from ceiling rose complete all as specified and directed.

S&F stepped type electronic fan regulator flush mounting type, 180Watt, 230Volt complete all as specified and directed.

S&F sheet metal enclouser DBs when MCBs to be used 8 way double door single pole & neutral with 200 Amps rated bus bar complete all as specified and directed.

S&F MCB SPN 32A to 40A, 230V, 10kA, B curve complete all as specified and directed.

S&F MCB SP 6A to 32A, 230V, 10kA, B curve complete all as specified and directed.

Supply and laying bricks old size, well burnt sub class 'B' bricks as in protection cover over under ground cable laid flat across the cable adjoining each other, laid dry complete all as specified and directed.

M&L sand filling for under ground cable protection with a layer of 8cm deep before laying and 15cm covering above the top ebdge of cable after laying and punning up to 18 cm depth complete all as specified and directed.

Boring holes under road or cutting the road /pavement /hard standing or any other situation by mannual or other means for inserting 25mm bore GI pipe for crossing the cable and making good both the end complete all as specified and directed.

S&F of galvanized iron pipe of 25 mm bore Light grade with all fittings for cable protection for road crossing/ culvert/ path/ on wall/ floor/ pole or laid in floor complete all as specified and directed.

Supply, lay jointing testing and commisioning XLPE insulated screened PVC bedded, armoured, heavy duty electric cable with stranded aluminium conductor, 1100 Volts grade, cross sectional area 10 Sqmm 2 core complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.3 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level ) with top edge of the plate not less than 1.5 metres below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts,check nuts, nuts and washers of GI or steel all as shown in electrical plate No 5 of SSR-I connected to earth test point by means of nut, bolts and washers made out of galvanised iron or steel all including earthing pit in PCC (1:3:6) type C1,RCC (1:2:4) type B1 precast cover slab with one handle made out of 8 mm dia round bar,20 mm dia (medium grade) protecation pipe and providing layer of charcoal or coke and salt in alternative layers,necessary earth work complete as specified or indicated including testng on completion complete all as specified and directed.

M&L for cutting steel water tubing and inserting with and including GI Tee, union, elbow fittings etc upto 50 mm dia complete for alteration or addition water pipe connection complete all as specified and directed.

S&F GI tubing of 25 mm dia, medium grade with all fittings and fixed to walls or ceiling or laid in floors complete all as specified and directed.

M/S ABHISHEK ENTERPRISES

Builders Harpal

M/S Gupta Builders

UTTRAKHAND BUILDERS

j u enterprises