SPECIAL REPAIRS TO WIRING AND ASSOCIATED WORKS IN NO 1 AIRMEN MESS, SPECIAL REPAIR REPLACEMENT OF EXISTING LIGHTS OF ROLE EQUIPMENT BAY OF ALFA SQN, PROVISION OF WATER SUPPLY TAPS TO EARTHING PITS AT ARRESTER BARRIER SITE AND CERTAIN MINOR WORKS AT A

Amount

Taking down the existing stainless steel sheet complete from the walls of cook house for the re-wiring and refixing the same after complete rewiring along with proper finishing/ final polishing/ hooking/ riveting etc. including taking down old plaster if required and providing 15mm thick plastering (CM 1:4) complete with making good disturbed surfaces wherever required for making good surfaces complete all as specified and as directed. Note :- All the removed stainless steel sheet will be deposited in the MES store for refixing again after the complete rewiring. If any portion of SS Sheet damaged during removal, the same shall be required to be repaired/ replaced with new SS Sheet as required if any to complete the work satisfactorily

Taking down carefully aluminium/ copper point wiring for light, fan, socket or power point etc. complete including conduit, fittings and fixtures such as ceiling rose, switch socket, pendants etc. including making good surface of wall, ceiling etc. complete all as specified.

Taking down carefully aluminium/ copper sub main wiring complete including conduit and conduit accessories all as specified.

Taking down existing unserviceable distribution board of any type including cutouts, MCBs etc. complete all as specified and as directed.

M&L for Point wiring complete as specified with 1100 volt grade 1.5sq.mm. (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade (IS:694) drawn through and including rigid non-metallic PVC conduit of suitable size not less than 20mm dia, with all fittings, concealed in wall/ roof / floor including pressed steel concealed terminal boxes of required size with top cover of 3 mm thick of plastic laminated sheet of required colour suitable for housing switches/ sockets/ regulators etc. duly earthed with same cable as for wiring above but green in colour as continuous earthing wire complete all as specified for one light/ fan point controlled by one switch 6 Amps 1 way. [Note:- M&L for cutting chases for concealed conduit wiring on any surfaces and making good disturbed surfaces to match with the existing surfaces in cement mortar 1:3 and finishing with existing finishes shall be deemed to be included in the quoted rate.]

All as per Item No. 5 herein before but for one 3 pin 6 Amp socket out let point on independent board.

All as per Item No. 5 herein before but for one 3 pin 6 Amp socket out let point on same board with other switches.

All as per item No. 5 herein before but point wiring with 1100 volt grade 2.5sq.mm. (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade (IS:694) duly earthed with same cable as for wiring above but green in colour as continuous earthing wire suitable for one 3 pin 16 Amps socket out let on independent board.

S&F Wall/surface mounted type LED light fitting batten type complete with LED 1x 20 watt (4 feet long), extruded aluminium body with heat sink provided for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with 3 core twisted flexible copper conductor cable complete all as specified and as directed including taking down existing unserviceable light fitting. Make :- Philips Cat Part No : BN100C LED20S-6500 PSU L120 GR S4, Havells Cat Part No : STOUT PLUS 600BS 20W LED 857SPCWH, Wipro Cat Part No : Wipro Garnet 20W LED Batten (White) D532065

S&F wall/ surface mounted type LED light fitting 1 X 9 to 12 watt (2' long) with extruded aluminium batten with multiple lumen packages complete with all accessories internally pre-wired and including making electric connection with flexible three core 1.50 sq.mm size stranded copper conductor cable from light fitting to ceiling rose complete all as specified and directed including taking down existing unserviceable light fitting. [Cat. Part No. BN 021 LED12S 6500 PSU GR (SmartBright) of make: Philips or Cat No. ENDURALINEARNEOBS10WLED865SPCWH of make: Havells]

S&F LED Bulk head Fitting including 1x10 watt luminaires Pressure die cast housing with IP 66 protection and IK 09 Impact resistance suitable for surface and wall mounting applications complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable, including taking down of existing light fitting etc complete all as specified and as directed including taking down existing unserviceable light fitting. Make:- Philips Cat No WT202W LED6S NW PSU S2 PC or equivalent make of Havells, Wipro

S&F LED Street Light Fittings having Ingress Protection class minimum IP-65 , suitable for road lighting luminaire with high power LED and maintenance free system for capacity 35 W complete with and including 32 mm bore light grade GI pipe bracket (1.5m long) duly bent to shape including 2 Nos MS flat iron (25mmx5mm) clamps, nuts, bolts, washers etc. complete all as specified and as directed including taking down existing unserviceable light fitting. Philips Cat Part No : BRP030 LED35 CW MR PSU GR DX, Havells Cat Part No : ENDURACITYLITE PLATPLUS SL35W LED 757SASYBOPC Wipro Cat Part No : LR02-391-XXX-57-XX

M&L for Angle Holder, insulated body with back plate with & including LED Lamp 12 Watt suitable for batten fittings complete all as specified and directed by Engineer-in-Charge.

S&F ceiling fan 1200mm sweep complete with down rod and other accessories working on 230 V AC with remote controller, minimum air delivery of 210 cfm with service value 6.00, BEE 5 star rated with brushless direct current motor (BLDC) complete all as specified including taking down existing ceiling fan and handing over to AGE E/M Store all as directed. Make :- Usha Energia 32 1200mm 5 Star Ceiling fan with BLDC Motor (Rich White) or Havells Efficiencia Neo 1200mm BLDC Motor (Elegant White) or Orient Electric I-Tome 1200mm BLDC

S&F Exhaust fan, Heavy duty, steel body AC single Phase, 230V of size 450mm sweep, 1400mm RPM with frame and louvers complete and other accessories etc all as specified and as directed. Make :- Usha Turbo Heavy Duty 450mm Grey/ Havells Turbo Heavy Duty 450mm Grey/ Crompton EXHD450-4-1 Neo Heavy Duty 450mm

S&F Electric water heater (geyser), storage type with ABS Plastic body with Stainless Steel inner tank and heating element up to 2 KW capacity 50 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, connection piece etc & electric supply connection complete including grouting nuts & bolts of 100 mm long for hanging the geysers, including PVC connection pipe 15mm dia, 450mm long heavy duty suitable for hot & cold water connections complete and plastering and finishing of disturbed surface of wall as per existing finish complete all as specified and as directed including taking down existing geyser. Note:- Old retrieved water heater shall be deposited in MES Store yard. Make: AO Smith Model No AO Smith HSE-HAS-Plus-RHS 50 Ltrs Storage Water Heater, White/ Havells Model No Monza DX H White Horizontal Type/ Racold Model No PLTSP-50 V/H Vertical Type.

S&F concealed type GI Sheet / PVC enclosure for switches / sockets etc. complete with a 25 Amps modular type motor starter (2 Module) with one SPN 'Ç' curve MCB of capacity 25 Amps (2 Module) & a 20 Amps 3 pin socket (2 module) including electrical connections all as specified and directed by Engr-in-charge.

S&F switch piano, flush type, single pole, one way, 5/6 Amps, 230V AC all as specified.

S&F socket outlet 6 Amp, 2 in 1, 5 pin, 230V AC

S&F socket outlet 6/16 Amp, 2 in 1, 6 pin, 230 V AC

S&F switch piano, flush type, single pole, one way, 15/16 Amps, 230V AC all as specified.

S&F ceiling rose PVC/ Poly carbonate isolated body, three terminal, 230 Volts AC complete all as specified.

S&F fan regulator electronic socket step type, 100 Watts, 230 Volts, flush type all as specified.

M&L for sub main wiring concealed complete with two runs of 1100 Volts grade 4 sq.mm (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade drawn through and including 20mm dia non metallic rigid PVC conduit and conduit accessories concealed in walls/ roofs/ floors etc. with one run of 1100 Volts grade 4 sq.mm (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade as earth continuity conductor all as specified. [Note:- M&L for cutting chases for concealed conduit wiring on any surfaces and making good disturbed surfaces to match with the existing surfaces in cement mortar 1:3 and finishing with existing finishes shall be deemed to be included in the quoted rate.]

M&L for sub main wiring concealed complete with two runs of 1100 Volts grade 6 sq.mm (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade drawn through and including 25mm dia non metallic rigid PVC conduit and conduit accessories concealed in walls/ roofs/ floors etc. with one run of 1100 Volts grade 6 sq.mm (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade as earth continuity conductor all as specified. [Note:- M&L for cutting chases for concealed conduit wiring on any surfaces and making good disturbed surfaces to match with the existing surfaces in cement mortar 1:3 and finishing with existing finishes shall be deemed to be included in the quoted rate.]

S&F sheet steel powder coated distribution board Vertical type TPN 8 ways, 415 volts, with 250 Amps rated fully insulated copper bus bar for each phase, 2 shrouded neutral bars, 2 earth bars, IP 54 protection and double metal door, with provision for FP MCCB as incomer and SP/ TP MCBs as outgoing all as specified and as directed. [MCCB & MCBs shall be measured and paid separately] [Cat No. 5077 52 of Make: Legrand or equivalent in Schneider/ L&T]

Excavating manually in trenches n. exc. 1.5m wide and n. exc. 1.5m in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. n. exc. 10sq.m. on plan and n. exc. 1.5m in depth and getting out in soft/ loose soil.

Taking up old unserviceable LT UG cable of various sizes complete all as specified and as directed.

Returning, filling in including spreading leveling watering and well ramming in layers not exc. 25cm in any type of soil.

Removing excavated materials to a distance not exc. 50m and depositing where directed at a level n.exc 1.50m above the starting point.

Supply and spread dry sand as in cushioning for UG cable all as specified in clause 19.75 of SSR Part I. [Note: Punned down thickness shall be considered for payment]

Supply and laying dry burnt bricks, sub class ‘B’ old size in cable trenches for cable protection complete all as specified and as directed by the Engineer-in-Charge.

Supply and laying XLPE insulated armoured heavy duty electric cable of size 3½ core 50sq.mm with aluminium conductor 1100 Volts grade, ISI marked as per IS 7098-I, laid in trenches/ ducts or fixing or passing through GI pipe across the road/ path/ drains/ along wall/ floor/ equipment etc. complete all as specified.

Supply and laying XLPE insulated armoured heavy duty electric cable of size 2 core 10sq.mm with aluminium conductor 1100 Volts grade, ISI marked as per IS 7098-I, laid in trenches/ ducts or fixing or passing through GI pipe across the road/ path/ drains/ along wall/ floor/ equipment etc. complete all as specified.

S&F MCCB 4 pole, 125 Amps, 16 KA, 415 Volts with thermal magnetic release connecting up with necessary spreader links complete all as directed.

S&F on load changeover switch 4 pole 125 Amps with sheet steel enclosure complete including taking down existing unserviceable switchgear all as directed.

S&F sheet steel powder coated distribution board SPN 8 ways, 240 volts, with 200 Amps rated bus bar, neutral link, earth bar, double door with IP 43 protection, suitable for mounting MCBs all as specified and as directed including grouting the new DB and making good the disturbed surfaces and applying finishes to match the existing all as specified and as directed.

S&F MCB SP, 240 volts, 6 to 32 Amps, 'C' curve, 10 KA all as specified and as directed.

S&F MCB DP 40 to 63 Amp, 10 KA, 230 V AC.

Horizontal Boring under hard standing/ pavements or roads manually using suitable auger for insertion of GI pipes up to 100mm bore and making good the disturbed surface complete all as specified and as directed. [Note: GI pipe will be measured and paid separately]

S&F GI tubes 50mm bore light grade laid in trenches/ drawn through horizontal boring for protection of cables

M&L for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm thick buried directly in ground (earth pit not less than 2.25m below ground level) with top edge of earth plate not less than 1.50m below normal ground level, connected to galvanized earth lead 4mm dia all as shown on electrical plate No. 3 of MES schedule 2009, Part–I (Specifications) and connected to main switch board/ main DB’s/ earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate 150 mm in all directions with & including watering pipe 20mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick precast RCC cover of size 450 mm X 450mm with 1:2:4, type B-1 duly reinforced with 8mm dia TMT steel bars @ 150mm c/c both ways with suitable lifting handle made of 10mm dia mild steel round bars to lift the cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 15mm bore including testing on completion of job complete all as specified and directed.

M&L for flame proof wiring with single core PVC insulated and unsheathed 1100 Volts grade (ZHFR) Zero Halogen Flame Retardant Smoke Free Non-Toxic Non-Corrosive Electric Cable with multi stranded copper conductor of size 1.5 Sq.mm phase and neutral drawn in and including ERW rigid steel stove enameled black conduit heavy duty ISI marked of size 20mm dia surface type including all flame proof conduit fittings and accessories such as tees, junction boxes, bends, duly tested by CMRI Dhanbad, duly earthed with same cable as for wiring above but green in colour as continuous earthing wire connected to earth dolly complete all as specified and directed by Engineer-in-Charge for one light/ fan point controlled by one flame proof rotary switch SP one way.

S&F flame proof weather proof for installation in hazardous area as per IS-2148/ 81/ LED Tube light fitting epoxy powder coated with provision of cable glands duly tested and certified by CMRI Dhanbad suitable for and including 16 Watt LED Tube made out of cast iron aluminium alloy LM-6 enclosure with clear heat resistant borosilicate glass tubing spring loaded non sparking bipin lamp holder built in control gear fitted with copper wound ballast condenser starter all accessories prewired including 02 Nos M-20 cable entries mounted on wall/ column steel structure complete all as specified and directed. Make :- Flexpro Cat Part No MFF/ S//1X40 or Crompton Greaves Cat Part No EXTN1 LT8-16/20 of equivalent of make Sudhir/ Baliga/ Shyam.

S&F Flame Proof Exhaust Fan 305mm (12") sweep, 1440 RPM speed, 23 volts, single phase, 50 Hz AC supply totally enclosed heavy duty motor with die cast aluminium rotor mounted on 02 ball bearings along with louvers with and including making suitable size hole on wall and making good the same as per existing finishes and necessary fixing arrangement on wall and connecting electrically with 3 Core 1.00 Sq.mm size PVC insulated FRLS flexible copper conductor cable overall sheathed drawn through flame proof flexible conduit all as required at site with connected accessories complete all as specified and as directed. [Make :- Sudhir Cat Part No EF/140 or equivalent in Crompton/ Shyam/ Baliga]

S&F Flame proof, weather proof direct entry type rotary switch with cable terminal box in cast aluminium alloy LM-6 enclosure epoxy powder coated single pole 230 volts 10 Amp ON / OFF switch AC certified by CMRI for group II-A & II-B including compression glands complete all as specified and directed. [Make :- Sudhir/ Shyam/ Baliga]

S&F sheet steel powder coated distribution board SPN 4 ways, 240 volts, with 200 Amps rated bus bar, neutral link, earth bar, double door with IP 43 protection, suitable for mounting MCBs all as specified and as directed including grouting the new DB and making good the disturbed surfaces and applying finishes to match the existing all as specified and as directed.

S&F MCB SPN, 240 volts, 40 to 63 Amps, 'C' curve, 10 KA all as specified and as directed.

Supply and laying XLPE insulated armoured heavy duty electric cable of size 2 core 6sq.mm with aluminium conductor 1100 Volts grade, ISI marked as per IS 7098-I, laid in trenches/ ducts or fixing or passing through GI pipe across the road/ path/ drains/ along wall/ floor/ equipment etc. complete all as specified.

S&F sheet steel powder coated distribution board TPN 4 ways, 415 volts, with 200 Amps rated bus bar, neutral link, earth bar, double door with IP 43 protection, suitable for mounting MCBs all as specified and as directed including embedded in wall, grouting the DB and making good the disturbed surfaces and applying finishes to match the existing all as specified and as directed.

S&F MCB TPN 40 to 63 Amp, 10 KA, 'C' curve, 415 V AC.

Supply and laying XLPE insulated armoured heavy duty electric cable of size 4 core 16sq.mm with aluminium conductor 1100 Volts grade, ISI marked as per IS 7098-I, laid in trenches/ ducts or fixing or passing through GI pipe across the road/ path/ drains/ along wall/ floor/ equipment etc. complete all as specified.

S&F Test point terminal block made of gun metal or phosphorus bronze of size 75x75x25mm drilled and screwed including 3 Nos. 8mm dia 25mm long hex head screws for holding the bronze plate including fastening/ bolting the roof down conductor and earth electrode over the bronze plate with copper bolts & nuts of suitable size, providing 10mm thick fibre sheet of size 15x15cm below the test point to avoid direct contact with wall including enclosing the test point with 1.6mm thick MS sheet front openable box duly painted complete all as directed by Engineer -in-Charge.

S&F of 20x3mm size copper strip as in earth continuity conductor or main earthing lead buried in ground, fixed to wall or in any other situation for loop earthing and the like up to test point mounted on necessary insulators and fastening screws, rawl plugs complete all as specified and as directed.

M&L for earthing comprising of copper earth plate electrode 600 mm X 600 mm X 3mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.50 m below normal ground level, connected to copper earth strip of size 20 X 3mm by means of nut-bolts, check nuts and washers of copper all as shown on electrical plate No. 3 of MES schedule 2009, Part–I (Specifications) and connected to main switch board/ main DB’s/ earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust and common salt all around the earth plate in alternate layers of minimum 150mm (compacted thickness) in all directions with and including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63mm thick GI sheet, wire gauge, 50mm thick RCC cover of size 450mm X 450mm in cement concrete 1:2:4, type B-1, duly reinforced with 8mm dia mild steel TMT bars @ 100mm both ways center to center with suitable lifting handle made of 10mm dia mild steel round bar to lift the cover, earth pit of PCC 1:3:6 type C-1, GI protection pipe light grade 40mm bore including testing on completion of job complete all as specified and directed.

S&F of Louvers suitable for Exhaust fan of sweep 450mm, made of aluminium sheet, square/round type as required suitable at site for direct air lift, including necessary hinges, nut-bolts etc. and making good the disturbed surface to match with existing surface complete all as specified and directed.

S&F suspended/ surface type High bay luminaire not less than 140 Watt, environmental friendly, energy saving long life corrosion resistant vertical surface mounting pressure die-cast aluminium housing and control gear with high power LED with all mounting accessories for fixing to truss of hangar/ MT garage etc complete prewired with flexible 3 core 1.50sq.mm size stranded copper conductor cable from light fitting to ceiling rose complete all as specified and as directed including taking down existing unserviceable light fitting. [Model: SAUSERPLUSHBP150WLED85790DTOLTG of make: Havells or BY415P LED160S CW HE WB FG PSU GR XTFCL S5 of make Philips or BGHBM NXT B 195L WH NB SD of make: Bajaj]

S&F PVC insulated three core flexible cable cord with 2.5 sq.mm multi-stranded copper conductor 1100 Volts grade for connection from pole box to security light fitting complete all as specified and directed

S&F LED Street/ security Light Fitting having Ingress Protection class minimum IP-65, with high power LED and maintenance free system for capacity 70 W complete with and including 32 mm bore light grade GI pipe bracket (1.5m long) duly bent to shape including 2 Nos MS flat iron (25mmx5mm) clamps, nuts, bolts, washers etc. complete all as specified and as directed. Philips Cat Part No : BRP032 LED70 CW MR PSU GR DX, Havells Cat Part No : ENDURAPEARLNEOSL 70WLED757PASYTOPC Wipro Cat Part No : LR02-781-XXX-57-XX

S&F shock proof, rust proof, fire retardant non transparent Kiosk pole box of size 310 X 210 X 120 mm made of Engineering plastic one piece moulding, for out door duty, with four Nos. of insulated aluminium bus bar of 60 Ampere capacity mounted on unbreakable insulators, 10 Ampere MCB SP with aluminium lugs of suitable size up to 50 Sq.mm including 02 Nos. 40X3 mm flat iron clamps duly painted both side with two coats of synthetic enamel paint over a coat of red oxide primer, necessary suitable size nut-bolts, washers etc. complete all as specified and as directed.

Supply and laying XLPE insulated armoured heavy duty electric cable of size 4 core 10sq.mm with aluminium conductor 1100 Volts grade, ISI marked as per IS 7098-I, laid in trenches/ ducts or fixing or passing through GI pipe across the road/ path/ drains/ along wall/ floor/ equipment etc. complete all as specified.

Supply & erecting in true vertical position, steel tubular swaged pole 410-SP-22, 8.5 meter long complete with mild steel base plate, pole cap, finial taper plug, bolts, nuts, washers etc. including painting the exposed outer surfaces with two coats of aluminium paint over a coat of red oxide primer including applying one coat of black bituminous paint on portion embedded in concrete foundation complete all as specified and directed. [Note: Earth work and excavation, PCC foundation & coping shall be measured and paid separately]

M&L for plain cement concrete 1:4:8 type D2 (using 40mm graded stone aggregate) as in foundations, filling and mass concrete, sub base for flooring etc. all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in foundations, filling and mass concrete, sub base for flooring etc. all as specified and as directed.

M&L for providing cement concrete type C1, 1:3:6 using 20mm graded aggregate as in lintels up to 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, copings, bed plates etc complete including necessary formwork all as specified.

Supply, installation, commissioning and testing of 2 TR capacity split type air conditioner, hi wall, copper wound, BEE 5 star rating, inverter type (DC inverter type) R-32 refrigerant with indoor and outdoor units and cordless remote control unit complete all as specified and directed. NOTE: - Power cable between indoor and outdoor unit, copper piping & drain pipe shall be deemed to be included in quoted rates. [Model: IA524DLU of make: Blue Star or equivalent in Voltas/ Carrier]

S&F 5 KVA capacity copper wound voltage stabilizer for automatic operation, single phase naturally air cooled, indoor type designed for input voltage of 90 to 300 Volt with stabilized output voltage at 230 Volts with accuracy of + 2.5% complete all as specified and directed. [Make: Sinetrac/ Blue Bird/ V-Guard]

S&F single pole and neutral enclosure with two pin and earth plug and socket with one single pole MCB 20Amps 240 Volts complete with plastic cover all as directed.

S&F MCB SPN, 240 volts, 6 to 32 Amps, 'C' curve, 10 KA all as specified and as directed.

S&F LED flood light luminaire, with high power LEDs 120 watt with pressure die cast aluminium housing & heat resistant toughed glass (IP 66 protection) with system lumen efficacy > 90 Lum / Watt, CRI >70, Colour Temperature >5700ºK, Power Factor >0.95, Driver Efficiency >85%, with operating voltage range 140 - 270 V AC, 50Hz ± 3Hz, Surge protection >3KV including driver and connecting up with three core PVC insulated, sheathed flexible copper conductor cable of size 1.0 Sq.mm from MCB to flood light for controlling the flood light complete all as specified and directed by Engineer in-Charge. [Cat No. JETAIRISFL120WLED757ARWBLTG of make: Havells/ Cat No. LF20-132-060-57-G2 of make: Wipro or equivalent in Make: Philips]

M&L for sub main wiring concealed complete with two runs of 1100 Volts grade 2.5 sq.mm (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade drawn through and including 20mm dia non metallic rigid PVC conduit and conduit accessories fixed to walls/ ceiling/ floors etc. with one run of 1100 Volts grade 2.5 sq.mm (nominal area) single core PVC insulated unsheathed cable with multi-stranded copper conductor of FR-LSH grade as earth continuity conductor all as specified.

S&F sheet steel powder coated distribution board SPN 2 ways, 240 volts, with 200 Amps rated bus bar, neutral link, earth bar, double door with IP 43 protection, suitable for mounting MCBs all as specified and as directed including grouting the new DB and making good the disturbed surfaces and applying finishes to match the existing all as specified and as directed.

S&F desert cooler with powder coated GI body, electric driven, single phase 220 Volts, 50 Hz with tank capacity 55 Litres, 1350 RPM, 3 speed controls complete all as directed. [Model No. Metal Ultracool 300S of make: Ram coolers or equivalent in Symphony/ Kenstar]

S&F GI tubes 80mm bore dia medium grade galvanized, with all fittings laid in trenches/ ducts/ floors etc and fixed complete all as specified and as directed.

All as per Item No. 74 herein before but 25mm bore dia

All as per Item No. 74 herein before but 20mm bore dia

All as per Item No. 74 herein before but 15mm bore dia

S&F 25mm bore gun metal globe or gate valve with iron wheel heads Class-II, screwed both ends for iron pipe all as specified.

All as per Item No. 78 herein before but 15mm bore

S&F plug type bib taps, 15mm bore cast iron, screwed for iron pipe complete all as specified and as directed

M&L for brick masonry Valve chamber of size 90cm x90cm x 60cm (internal dimensions), with 230mm thick fly ash brickwork construction in CM 1:4, including all necessary excavation and earth work in soft/ loose soil, returning, filling in, disposal of surplus spoil to a distance n. exc. 50m and depositing where directed, 100mm thick PCC foundation 1:4:8, type D-2 (using 40mm graded crushed aggregate), rendering 15mm thick in CM 1:4 internally finished even and fair and pointing flush externally as the work proceeds in the same mortar, mild steel manhole cover frame with MS sheet cover 3mm thick with handle and locking arrangement, painting all the exposed M.S work with two coats of synthetic enamel paint over a coat of red oxide primer and painting all the M.S embedded in PCC with two coats of black bituminous paint complete all as specified and directed by Engineer-in-Charge.

M&L for plain cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in foundations, filling and mass concrete, sub base for flooring etc. all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks, double layered of capacity 500 ltrs (cylindrical vertical with closed top) hoisted and fixed in position complete including necessary GI tank nipples all as specified and as directed by Engineer-in-charge.

Supply, install, testing & commissioning bore well submersible pump set 1 HP, single phase suitable for 30m head, 12000 LPH discharge complete all as directed. [Make: Kirloskar/ KSB/CG]

Supply, install, testing & commissioning control panel (Starter) suitable for submersible pump set 1 HP, single phase suitable for 30m head, 12000 LPH discharge complete with provision of Amps & Voltmeter all as directed. [Make: L&T/ BCH/ Havells]

Supply & fixing submersible copper cable flat type three core of size 2.5 Sq.mm complete all as specified and as directed. [Make: Finolex/ Polycab/ Havells]

S&F flexible steel supported rubber hose pipe 25mm bore for delivery pipe of submersible pump set complete fixed with steel clamps on both ends complete all as specified and as directed.

S&F steel rope 8mm dia, ISI marked, heavy duty grade for holding the submersible motor complete all as specified and as directed.

M/s Agarwal Builders