Construction of Animal Husbandry EPI Centre at Koparali Ta: Vapi Dist: Valsad

No figures

1 Excavation for foundation upto 1.5 m depth including 365.70 Cumt 117.08

sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead.(B)

Dense or Hard soil

2 Excavation for foundation for depth from 1.5 m to 3.0 m 122.70 Cumt 162.56

including sorting out and stacking of useful materials

and disposing off the excavated stuff upto 50 Meter

lead.(B) Dense or Hard soil

3 Filling in foundation and plinth with sand in layers of 20 22.00 Cumt 460.19

cm. Thickness including watering ramming and

consolidating etc. comp.

4 Filling available excavated Earth (Excluding Rock) in 137.60 Cumt 130.39

trench plinth side of foundation . in layer not excluding

20 cm in depth consolidation each deposited layer by

ramming and watering etc. complete

soil in layer of 20 cm in thickness including ramming

watering and consolidating etc. complete

6 Applying general insecticide pest control treatment to 81.90 Sqmt 89.28

floors, cupboards etc including labour material etc.

complete. Using Imidacloprid 30.5 SC. As Per 6113 Part -

II (0.075% concentration by mass) is recommended

10.5ml chemical diluted with 5 liters of water

application 0.5 liters chemical/ sqm of surface is

recommended as per I.S.

7 Providing and laying cement concrete 1:3:6 (1-Cement : 5.70 Cumt 3005.76

3- coarse sand : 6- machine cut stone aggregates 40 mm

nominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

8 Providing and laying controlled cement concrete M150 69.25 Cumt 4289.47

for curing complete including cost of formwork but

excluding the cost of reinforcement for reinforced

concrete work in PCC

9 Providing and laying controlled cement concrete M250 65.30 Cumt 4519.04

and curing complete including the cost of formwork and

excluding reinforcement for reinforced concrete work

for Foundations, Footings , Mass concrete , for Footing

Item Rate In

Description of Item Quantity Unit Amount

No figures

10 Providing and laying controlled cement concrete M250 3.30 Cumt 7131.61

and curing complete including the cost of formwork and

excluding reinforcement for reinforced concrete work

for ,Column Upto GL

11 Providing and laying controlled cement concrete M250 25.70 Cumt 6057.98

and curing complete including the cost of formwork and

excluding reinforcement for reinforced concrete work

for ,Plinth Beam/Ground Beam

12 Providing and laying controlled cement concrete M200 10.40 Cumt 5496.72

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Plinth Slab,

13 Providing and laying controlled cement concrete M200 0.90 Cumt 7162.92

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Column Upto PL

14 Providing and laying controlled cement concrete M-200 22.80 Cumt 7086.16

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Columns, pillars posts and struts For

15 Providing and laying controlled cement concrete M-200 2.60 Cumt 7086.16

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Columns, pillars posts and struts For

16 Providing and laying controlled cement concrete M.200 8.70 Cumt 6022.67

and curing complete including the cost of formwork and

excluding reinforcement for reinforced concrete work in

(C) Ground floor Beams,

17 Providing and laying controlled cement concrete M-200 0.30 Cumt 6331.13

and curing etc. complete including the cost of form work

and reinforcement for reinforced concrete work in (c)

Chhajja for Ground floor

18 Providing and laying controlled cement concrete M-200 0.70 Cumt 7279.31

and curing etc. complete including the cost of form work

and reinforcement for reinforced concrete work in (c)

Lintal for Ground floor

19 Providing and laying controlled cement concrete M.200 9.60 Cumt 6745.83

and curing complete including the cost of formwork and

excluding reinforcement for reinforced concrete work in

(C) Ground floor Slab

20 Providing and laying controlled cement concrete M-200 5.20 Cumt 6217.80

for RCC work and curing complete including the cost of

form work but excluding the cost of reinforced concrete

work in coping on Ground Floor

Item Rate In

Description of Item Quantity Unit Amount

No figures

21 Providing and laying controlled cement concrete M-200 1.00 Cumt 6217.80

for RCC work and curing complete including the cost of

form work but excluding the cost of reinforced concrete

work in coping on F Floor

22 Providing IS Mark TMT FE-500D bar reinforcement for 18852.00 Kg 76.26

RCC work including bending & placing in position

complete up to All floor Level

23 Brick work using common burnt clay building bricks 46.00 Cumt 4021.02

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:5. (1- Cement :

5 -fine sand) (B) Conventional below plinth

24 Brick work using common burnt clay building bricks 32.30 Cumt 4295.99

having crushing strength not less than 35 kg./Sq.Cm. in

foundation and plinth in Cement Mortar 1:5. (1- Cement :

5 -fine sand) (B) Conventional For GF

25 Half Brick masonry in common brunt clay building 26.80 Sq m 652.99

bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse

sand ) in foundation and plinth (B) Conventional in

super structure. for GF

26 Half Brick masonry in common brunt clay building 48.60 Sq m 652.99

bricks having crushing strength not less than

Kg/Sq.Cm. in Cement mortar 1:4 (1- Cement : 4 -coarse

sand ) in foundation and plinth (B) Conventional in

super structure. for FF

27 Providing and fixing 150 mm wide, approved quality 53.10 Sqmt 295.93

chicken wire mesh at junction of brick work and RCC

work or two dissimilar surfaces, at all heights fixed by

nails, rowal plugs or tag before applying the plaster,

including curing, scaffolding all complete as directed.

28 Providing 15mm thick cement plaster in single coat on 235.50 Sqmt 159.26

Rough (Similar)side of single or half brick walls for

interior plastering upto floor two level and finished even

and smooth in (ii) Cement mortar 1:4 (1-cement :4-

sand). For G Floor

29 Providing 15mm thick cement plaster in single coat on 53.40 Sqmt 159.26

Rough (Similar)side of single or half brick walls for

interior plastering upto floor two level and finished even

and smooth in (ii) Cement mortar 1:4 (1-cement :4-

sand). For F Floor

Item Rate In

Description of Item Quantity Unit Amount

No figures

30 Providing 10 mm. Thick cement plaster in single coat for 65.00 Sqmt 140.95

plastering on ceiling and soffits of stairs and finished

even and smooth in : (I) Cement mortar 1:4 (1 cement :

4 sand) smooth finish etc. complete. G Floor

31 20 mm thick Sand faced cement plaster with 1cmx1cm 731.80 Sqmt 322.19

grooves as suggested by this office consisting of 12 mm

thick backing coat of C.M. 1:3 ( 1 cement : 3 coarse sand )

and 8 mm thick finishing coat of C.M. 1:1 ( 1 cement :

coarse sand) for all heights as directed etc. complete.

and as per pattern sample aprroved by the architect or

directed engineer in-charge

32 Providing throating or plaster drip and moulding to 3.90 Rmt 42.17

R.C.C. Chhajja.

33 Applying two coats of Acrylic lapy (putty) & two coats of 353.90 Sqmt 40.59

primer of approved brand and manufacture on new wall

surface to give an even shade including thoroughly

brushing the surface free from mortar dropping and

other foreign matter and sand papered smooth.

34 Wall painting (two coats) with plastic emulsion paint of 288.90 Sqmt 80.35

approved brand and manufacture on undecorated wall

surface to give an even shade including throughly

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

35 Painting (two coats) with plastic emulsion paint of 65.00 Sqmt 85.76

approved brand and manufacture on undecorated ceiling

surface to give an even shade including throughly

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

36 Wall Painting (Two coats) with weather proof acraylic 731.80 Sqmt 114.53

emulsion paint of approved brand and manufacture and

of required shade on exterior wall surface to give an

even shade over and including primery coat with Alkaly

resistance primer of approved brand after thoroughly

brushing surface to remove all dust and remains of

loose powdered material etc. copm. for all height

Item Rate In

Description of Item Quantity Unit Amount

No figures

37 Providing and laying broken chine mosaic flooring for 61.00 Sqmt 747.29

terrace using 12 mm to 20 mm broken pieces of glazed

tiles to be laid over cement mortar 1:3 to plain or slope

and to be tempered to bring mortar creme out upto

surface using white cement including rounding off

junctions and extending them upto 15 cm along the

wall,clearing with water and oxalic acid etc. as directed.

38 Providing and laying cement concrete flooring 1:2:4 (1- 61.00 Sqmt 322.93

cement : 2- coarse sand : 4-graded stone aggregate

20mm nominal size) laid in one layer and finished with a

floating coat of neat cement. (B) 50mm thick

39 Providing Plinth Protection to Building including 50.20 Sqmt 2279.57

excavation in ordinary soil and laying cement concrete

1:3:6 using stone aggregates of 40mm nominal size in

foundation layer 125 mm thick+ 125mm thick sand layer

below pre-cast Rubber Dye inter locking concrete block

60mm thick with grade of concrete M300 pneumatic

compressed by mechanically pressed and as per

approved design including 75mm Sand layer for

levelling and filling the joint with sand in proper line and

level etc. complete, Including Providing and fixing pre-

cast concrete kerb stone of grey cement based concrete

block 30cm length, 30cm height and 15cm thick made of

M250 grade concrete as per approved design and

including excavation for fixing in proper line and level,

filling the joint with C:M 1:3 (1cement:3 fine sand) etc.

40 Providing and fixing Approved Brand (30mm) Three 5.80 Sqmt 3363.60

track alluminium window standerd extruded colour

anodized aliminium section with Frame having frame

bottom member @ wt. Of 1.223 Kg/Rmt , frame Side and

top member @ wt. Of 1.685 Kg/Rmt with sliding

shutters of single glass shutter top bottom member @

wt. Of 0.839 Kg/Rmt & side member @ wt.of

Kg/Rmt & Inter lock member @ wt.of 0.731 Kg/Rmt

with 5 mm thick transparent plain float glass in shutter

including fitting, fixtures, rubber gasket and transparent

silicon sealant as per drawing and instruction of

Engineer - in - charge etc. completed for window three

Item Rate In

Description of Item Quantity Unit Amount

No figures

41 Providing & Fixing in position standard extruded 0.40 Sqmt 2722.95

approved colour anodised Aluminum Ventilation with

outer frame 65 x 25 x 1.50 mm Stander Box Frame @ Wt

0.833 kg/Rmt with 5mm thick fixed ground glass fixed to

alluminium strip blade fixed or adjestable ventilation &

including all required materials, fixtures, fastenning,

labours and equipments as per detailed drawing as

directed. For Ventilators

42 Providing and fixing 35mm thick flush double door 3.00 Sqmt 4682.36

shutter with 100x50mm wooden frame , solid core for

durable grip of hinges & Double shutter with required

75x35mm wooden batten having 1mm thick pattern

lamination on both side, Durable Grip shall be providing

with both side 60cm long stainless steel handle , 2 tower

bolts and aldrops including necessary Locking system

S.S. fixtures & fastenings etc. directed by engineer in

43 Providing and fixing 35mm thick flush single door 4.20 Sqmt 3881.43

shutter , solid core for durable grip of hinges & single

shutter with required 75x35mm wooden batten having

1mm thick pattern lamination on both side, Durable

Grip shall be providing with both side 60cm long

stainless steel handle , 2 tower bolts and aldrops

including necessary Locking system , S.S. fixtures &

fastenings etc. directed by engineer in charge.

44 Providing and fixing FRP frame size 100 x 50 mm and 35 1.90 Sqmt 2363.40

mm thick ( Fiber Glass with PUF Injection ) FRP depress

panel Single or Double shutter having extra

reinforcement on sides & edges in Gel coat finish.The

core of the both shutter & frame is to be filed up with

injected fire retradat grade polyurethene foam done in

situ along with embeded wooden pieces for stiffening &

also taking hinges & fintures.The whole FRP frame &

single or double shutter is to be waterproof,

weatherproof, termite proof & resistance to mild

acid/alkali. Rates are to be inclusive of S.S hinges with

necessary screws & S.S fixtures & fastenings & fartener

sleeve.Colour and Shade approved by Engineer-In-

45 Providing & Laying 60 x 60 mm GVT vitrified 8 mm thick 52.50 Sqmt 1581.66

tile flooring over 20 mm (average) base of cement

mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or

fixing on existing flooring by adhesive material including

dismentaling of existing flooring and jointed with color

cement slurry including finised with flush pointing &

cleaning the surface etc. complete shade approved by

directed engineer in-charge.

Item Rate In

Description of Item Quantity Unit Amount

No figures

46 P & L 60x60 cm GVT vitrified 8 mm thick tile risers of 5.00 Sqmt 1233.21

steps,skirting Dedo of cement mortar 1:3 (1cement :

coarse sand)and jointed with by adhesive materials

including colour cement slurry including finished with

flush pointing & cleaning the surface etc. complete for

including colour approved by directed.

47 Providing and laying antiskid ceramic tiles 30 x 30 cm 2.50 Sqmt 970.07

size 6 mm thick in flooring treads of steps and landing

laid on a bed of 12 mm thick cement mortar 1:3(1-

cement:3-coarse sand)finishing with flush pointing in

white cement

48 Providing and laying primium printed glazed tiles tiles 24.60 Sqmt 1441.22

size 30 x 60 cm 8 mm thick in skirting risers of steps and

dedo on 10 mm thick cement plaster 1:3 (1-

cement:3coarse sand) and jointed with colour cement

slurry etc completed.

49 Providing and laying machine cut free edge machine 2.20 Sqmt 944.35

Green Marble Slab 18 to 20 mm finished treads and

risers in length with 1cm projecting nozing rounded

moulding in ttread laid over 20 mm (av.) thick of CM 1:6

on treads and 10mm thick CM 1:3 on risers jointed with

grey or colour cement slurry including rubbing and

polishing incl. making Three No.s of grooves of size

3mm X 3mm along the length of treads etc. complete

50 Providing and fixing frosted finished 600mm x 1200mm 0.80 Sqmt 6008.49

glass urinal partition with crystalline Dhar polish on

exposed edges, supported by SS legs and fitting bracket

clamp with cut holes and silicon grouting, including all

accessories and labor charges directed by the

engineering in charge, etc. complete

51 Providing and fixing mirror polished 18 mm thick Green 25.50 Sqmt 2271.49

Marble stone with full round edge and polished of

approved quality in clading on sill and around the

doors/ windows/ ventilation with 12 mm thick cement

mortor CM (1:4) and fixing with cement slurry &

adhesive including moulding of exposed edges as

directed by engineering in charge etc. complete.

52 Providing and fixing pre-cast Rubber Dye inter locking 90.20 Sqmt 686.90

concrete block 60mm thick with grade of concrete M200

pnumatic compressed by mechanically pressed and as

per approved design including 75mm Sand layer for

levelling and filling the joint with sand in proper line and

level etc complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

53 Providing and fixing M.S Safty Grills having 16mm Solid 18.20 Sqmt 2112.92

MS Squre bar Horizontally at every equal 0.10m C/C

distance and 2 no of bar Vertically at every equal 0.375m

C/C distance Fixing on around (5x40) mm Solid MS Patti

including cutting, welding and fabrication etc; including

one coat of primer of approved quality and two coats of

oil painting as per detail drawing etc. complete as per

directed Engineer in charge.

54 Providing erecting and fixing double coated PVC. (ISI) 5000.00 Litre 3.95

water tank of required capacity each with all necessary

fittings and connection etc. complete on terrace.

55 Providing laying and jointing in true line and level 50mm 54.00 Rmt 195.67

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

56 Providing laying and jointing in true line and level 40mm 34.00 Rmt 148.12

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

57 Providing laying and jointing in true line and level 25mm 30.00 Rmt 91.84

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

Item Rate In

Description of Item Quantity Unit Amount

No figures

58 Providing laying and jointing in true line and level 15mm 15.00 Rmt 72.65

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

59 Providing, laying and jointing in true line and level 160 10.00 Rmt 831.22

diametre U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size

mm diametre x 210 mm length x 196 mm heigh at every

2000 mm center to center or shall be concealed in walls

as directed including necessary fittings such as bends,

shoes etc. including testing of pipes and joints and

jointed with adhesive solvent cement including cost of

all materials.

60 Providing, laying and jointing in true line and level 110 20.00 Rmt 836.73

diametre U.P.V.C (Type B) conforming to IS 13592-1992

with one end plain and other end socketed with rubber

ring, & fittings conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp of the size

mm diametre x 149 mm length x 145 mm heigh at every

2000 mm center to center or shall be concealed in walls

as directed including necessary fittings such as bends,

shoes etc. including testing of pipes and joints and

jointed with adhesive solvent cement including cost of

all materials.

Item Rate In

Description of Item Quantity Unit Amount

No figures

61 Providing, laying and jointing in true line and level 75 10.00 Rmt 716.09

mm dia. UPVC SWRType B pipe conforming to IS 13592-

1992 with one end plain and other end socketed with

rubbering and fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp at every

mm c/c or shall be conceled in walss as directed

including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all materials.

62 Providing and fixing in PVC SWR cowel went 75mm dia 1.00 No 16.16

to pipes.(B) 75mm dia.

63 Providing and fixing in PVC SWR cowel went 110mm dia 4.00 No 29.29

to pipes.(B) 110mm dia.

64 Providing and fixing PVC SWR Nahni trap IS 14735 for 2.00 No 571.08

drain - 100 mm diameter with jali of the following

nominal diameter of self cleansing design with C.I scread

down or hinged grating including the cost of cutting and

making good the walls.

65 Providing and fixing wash down water closet (European 1.00 No 2853.25

type W C pan) with integral P and S trap including

jointing the trap with soil pipe in cement mortar 1:1 (1

cement five sand) including providing and fixing plastic

seat cover for wash down WC with CP brass hinges and

rubber buffers back plastic seat with a pair of C I or MS

bracket with complete fitting such as lead valve siphon

15 mm dia brass ball valve with polythene float CP brass

handle unions and couplings for connection with inlet

out let and over flow pipes 40 mm dia porcelain

enameled flush bend including cutting holes in walls and

making good the same connection the flush bend with

cistern and closet vitreous china.

66 Providing and fixing stainless steel grab 22 cm x 60 cm 1.00 No 1492.78

on door and handicapped toilet including all fixture and

accessary etc completed as per directed engineer in

67 Providing and fixing ball cock of approved. quality as 2.00 No 189.84

directed.(A) Copper Metal (ii) 50mm dia.

Item Rate In

Description of Item Quantity Unit Amount

No figures

68 Providing and fixing washbasin with single hole for pillar 1.00 No 2102.82

tap with C.I. or M.S. brackets painted white including

sutting holes and making good the same including Brass

waste, and M I fisher union fittings including pvc

connection and waste pipe & all necessary fittings For All

Floor (A) Vitreous China:(ii) Flat Back washbasin

mm x v 400mm size. (i) In white colour

69 Providing and fixing 600mm x 450mm bevelled edge 1.00 No 833.73

mirrror of superior glass mounted on 6mm thick A.C.

sheet or plywood sheet and fixing to wooden pluge with

C.P. brass screws and washers.

70 Providing and fixing C.P. brass towel rail comlete with 1.00 No 603.19

C.P. brass brackets fixed to wooden plugs with C.P. brass

scews.(B) 600mm x 20mm size

71 Providing and fixing screw down bib taps of following 2.00 No 186.83

size.(A) Brass screw down bib tap polished bright. (i)

72 Providing and fixing Urinal of approved quality including 1.00 No 1550.99

connection with trap and with integral longitudinal flush

pipe.(A) Squating plate pattern white earthenware

73 Providing laying (to level or slopes) and jointing 179.00 Rmt 665.48

reinforced concrete Light duty non-pressure pipes I.S.

class NP2 of the following internal diameter with collars

and butt ends prepared for collar joints including testing

of joints complete.(D) 300mm

74 Providing and fixing S.W. gully trap with C.I. grating 1.00 No 1246.92

brick masonry chamber and water tight C.I. cover with

frame of 300mm x 300mm size (inside) with standard

weight (i) Square mouth traps (B) 150mm x 100mm size

P or R type

75 Constructing brick masonry chamber for underground 13.00 No 3223.92

C.I. Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

precast RCC cover 455mm x 610mm intenal dimensions

with frame (R.C.C. top slabe with 1:2:4 mix (1-cement :2-

coarse sand :4-graded stone aggregate 20mm size)

foundation concrete 1:5:10 inside plaster 15mm thick

with cement mortar 1:3 finished smooth with a floating

coat of neat cement on walls and bed concrete etc.

complete (i) Inside dimensions 455mmx 610mm and

450mm deep for single pipe line.

Item Rate In

Description of Item Quantity Unit Amount

No figures

76 Constructing brick masonry chamber for underground 8.00 No 3933.95

C.I. Inspection C.I. Inspection chamber and bends with

briocks having croshing strength not less than 35Kg.

Cm2 in C.M. 1:5 precast RCC cover 500mmx 700mm

intenal dimensions with frame (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded stone

aggregate 20mm size) foundation concrete 1:5:10 inside

plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and

bed concrete etc. complete (i) Inside dimensions

500mmx 700mm and 450mm deep for single pipe line.

77 Extra over items for every additional depth of 0.1M. of 5.00 No 242.39

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 455mm x 610mm size.

78 Extra over items for every additional depth of 0.1M. of 5.00 No 264.86

part thereof beyond 450mm depth for Brick masonry

chamber.(i) for 500mm x 700mm size.

79 Providing and fixing MS Ladder of required pattern with 500.00 Kg 98.98

MS flats(30x3mm) or round or square bars (12mm) at

required spacing & with round headed bolts and nuts or

screws or welding including primer coat of approved

quality and two coats of oil paintas as directed by

engineer in charge

80 Constructing drinking/Handwash Platform of 18 mm 1.20 Sqmt 5248.97

thick Polished Black Granite having 0.45m width and

0.60m height including 0.60m support at every 0.7m c/c

with cementing Materials / adhsives including makeing

necessary grooves in walls iwith all labour material of

approved quality incl. full moulded round front edge

granite strip of one side polished and jointed with grey

cement slurry including rubbing and polishing etc.

complete for all floors

81 Providing and fixing in position 300 mm high, 150 mm 20.00 No 1333.20

wide English letters made from 1.0 mm thick stainless

steel sheet as directed by Engineer in charge with all

necessary tools & plants etc. complete.

82 Providing and fixing in position 150 mm high, English 20.00 No 686.80

letters made from 1.0 mm thick stainless steel sheet as

directed by Engineer in charge with all necessary tools &

plants etc. complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

83 Providing and fixing of Ridge flashing for roof panel shall 67.90 Sqmt 768.12

be made out of 0.5 mm thick pre coated GI sheet . The

Precoated sheet shall be of minimum 240 mpa steel

grade confirming to IS 14246:1995 and shall have zinc

coating of minimum 120 gsm as per IS:277:1992 , 5-7

microns epoxy primer on both side of the sheet and

polyester top coat 15-18 micron. The PPGI Sheet shall

have plastic protective guard film of minimum

microns to avoid scratches during transportation. The

ridge shall be fixed to the steel members by pop rivet or

self drilling/self stitching fastners @ maximum 450 mm

c/c along length of capping/flashing etc complete.

84 Steel work, welded in built up sections framed work 4759.30 Kg 90.48

including cutting,hoisting, fixing in position and applying

a priming coat of read lead paint. (A)In beams and joists,

hannels angles Tees, flats, with connecting plates or

angle cleats as in main and cross beams. Hip and jack

rafters, purlins conneted to common rafters and the like.

85 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1- 1.00 No. 11029.97

cement :2-coarse sand : 4-graded stone aggregate 20mm

nominal size) foundation concrete 1:3:6 mix (1-cement :

3- coarse sand :6-Brick bats 40 + 50mm size) inside

plastering 15mm thick with Cement Mortar 1:3 (1-

Cement : 3-coarse sand) finished with a floating coat of

neat cement and making channels in cement concrete

1:2:4 mix (1-Cement :2-Coarse sand :4-stone aggregate

20mm nominal size) finished smooth complete including

curing and festing (i) Inside size 900mm x 1200mm and

1.5M. deep including C.I. cover with frame size 560mm

diameter total weight of cover and frame to be not less

than 128 kgs. (Wt. of cover 64 Kg. and Wt. of frame

Kg.)(A) With 230mm thick walls of brick msonry using

brick having crushing strength not less than 35Kg. /

Sq.cm. in Cement Mortar 1:5 (1- Cement: 5- Coarse sand)

(1) A type depth 0.90 Metre for 150mm diameter sewer

86 Providing and fixing and floor 10.0 Kg. F/Cm2 working 50.00 Rmt 336.24

pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression

type fittings, wall clipsetc. including making good the

wall ceiling and floor.(G)110 mm

87 Providing and fixing and floor 10.0 Kg. F/Cm2 working 10.00 Rmt 696.90

pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression

type fittings, wall clipsetc. including making good the

wall ceiling and floor.(G)180 mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

88 Providing junction for rain water juncton chamber of 1.00 Nos. 9204.13

size 0.60x0.60x0.75m with excavation of size 1.96x1.96

m & 0.15m thick c.c.1:2:4 bed concrete including brick

masonary wall in CM 1:6 of 0.75m height & 0.23m thick

with 15mm thick cement plaster inside & outside &

1.06x1.06 RCC (1:2:4) slab of thickness 0.15m with CRS

steel and 0.60mx0.45m cast iron manhole cover with

frame weight not less than 35 kg as per directed by

Engineer-in-charge

89 Providing and installation Recharge pit of “RAIWOHA” 1.00 Nos. 109645.60

Make 3 layer RCC Precast Injection well system of size

1.5 meter Dia. X 3.4 Meter Height rein forced concrete

precast three layer module with 6” dia x 12” dia. V wire

screen of 0.75mm x 1.0 mm Slot size in SS 304 material

and 1.0 meter height with MS Top cover and required Air

vent including all necessary excavation and

transportation at site including required filter media for

the recharge system as per site requirement.

90 Drilling of min. 250 mm dia. bore hole in all strata 30.00 Rmt 1252.32

including dualover burden strata by combination

DR/DTH rig including lowering 200 mm dia MS ERW

pipes in bore hole and testing etc.all work as per directed

engineer incharge.

91 Supplying slotted PVC pipes of approved quality at site of 30.00 Rmt 555.50

work confirming to IS. 1239/1974 180mm dia.

92 Construction of granular sub-base 150 mm thick by 16.50 Cum 993.84

providing coarse graded machine crushed B.T. material

satisfying MOST specification of grading I (B.T. stone

aggregate 53 mm to 26.5 mm 35 %, 26.5 to 4.75 mm -

% and 2.36 mm below - 20 % )including spreading in

uniform layer with motor grader on prepared surface,

mixing by mix in place method with rotavator at OMC

and compacting with vibratory roller to achieve the

desired density etc. complete.

93 Providing and fixing pre-cast concrete kerb stone of gray 30.00 Rmt 361.64

cement based concrete block 30cm ength,30cm height

and 15cm thick of M250 grade concret as per approved

design and including excavation for fixing in proper line

and level,filling the joint with C:M 1:3 (1cement:3fine

sand) etc complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

94 Box cutting the road surface to proper slope and camber 26.00 Cum. 104.04

for making a base for road work including removing the

excavated stuff and depositing on the road side slope as

directed upto upto All lift and lead..

95 Providing, laying and compacting natural sand & gravel[ 4.00 Cum. 356.53

C.B.R. not less than 20%] below sub base course

including carriage of materials spreading in uniform

layer manually on prepared base and compacted with

vibratory roller to achieve desired density including all

materials, labour etc. complete.

96 Providing and laying wet mix macadam base course 250 11.00 Cum. 1070.60

mm thick in two layers using machine crushed B.T. chips

as per required gradation mixing with required optimum

quantity of water, conveying the mix to site of work,

spreading in to grade and camber with mechanical paver

and consolidation each layer with vibratory roller

including cost of material labour plant and equipment

etc. complete.

97 Compaction and finishing of cement concrete road by 30.00 Sqm 65.65

trimix process providing extra Labour charges for the

trimix vacume dewatering service process on cement

concrete road sutface by using vacuum dewatering

pump floater surface vibrator including making groves

and rough finish to surface including leveling etc

98 Providing and fixing concertina coil fencing with 90.00 Rmt 864.56

punched tape concertina coil 600 mm dia 10 mt

openable length having 50 no rounds per 6 mt length,

upto 3mt height of wall with existing angle iron (50mm

x50mm x5mm )requird shaped As per Directed

Engeenier in charge. placed 2.4mt or 3.00mt apart and

with 4 horizontal R.B.T. reinforced barbed wire(3 mm)

stud tied with G.I. staples and G.I. clips to retain

horizontal, including necessary bolts or G.I.barbed wire

tied to angle iron, all complete as per direction of

Engineer-in-charge, with reinforced barbed tape

(R.B.T.)/Spring core (2.5 mm thick) and weight

gm/meter at compound wall for ESR M4/ intakewell.

99 Constructing providing and fabricating cattle guard 9.00 Sqmt 5096.46

using channel section frame of size ISMC series 100 mm

x 50 mm (Weight 9.20 kg/Rmt) and ISMC section

mm x 75mm (weight 11.50 kg/Rmt) intermediate

support for welding G.I.pipe at 12 Cm C/C of size 50 mm

in a frame made of Channel section size 100 mm x

mm all round including fixing the unit on prepared

chamber of masonary wall using MS hold fast embeded

in masonary wall top as directed by Engineer in charge

and as per drawing and necessary required arrangement

etc complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

100 Point wiring for Light / Bell with 2-1.5 sq.mm & earth 19.00 Pt. 485.81

wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up

to 10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe

erected, with necessary Lamp holder/ceiling rose /

H.D.Connector as directed. (f) with medium class Rigid

PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

101 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 6.00 Pt. 674.68

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade

FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe

erected. with necessary ceiling rose / H.D.Connector as

directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete

102 Point wiring for on board Looped Plug with 6A Modular 4.00 Pt. 257.55

type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following

type accessories Cat. III

103 Providing following type of Modular Type Accessories 2.00 Ea. 151.50

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (1)One No. SP 6 Amp. Cat.III

104 Providing following type of Modular Type Accessories 2.00 Ea. 151.50

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (2) One No 5 pin plug Cat.III

Item Rate In

Description of Item Quantity Unit Amount

No figures

105 Providing following type of Modular Type Accessories 7.00 Ea. 25.25

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (7) Blank Plate Single Cat.III

106 Providing following type of Modular Type Accessories 4.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (8) Computer RJ-45 socket Cat.III

107 Providing following type of Modular Type Accessories 3.00 Ea. 180.79

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (9) 16 Amp. SP one way switch

108 Providing following type of Modular Type Accessories 4.00 Ea. 199.98

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (10) 6/16Amp. Universal socket

109 Providing following type of Modular Type Accessories 1.00 Ea. 410.06

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (14) 16A Double Pole Modular MCB

Switch Cat.III

110 Providing and erecting ISI mark Medium class RIGID PVC 85.00 Mtr. 24.24

PIPES of following size complete to be erected on/in wall

or ceiling erected with necessary PVC fittings & Junction

boxes fixed with adhesive solution & Clamps with

following dia of pipes, in approved manner as directed

111 Providing and erecting Mains with 1.1 KV grade FRLS 187.00 Mtr. 82.82

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) With

medium class Rigid PVC pipe and accessories (b) 2 wire

Item Rate In

Description of Item Quantity Unit Amount

No figures

112 providing and erecting Mains with 1.1 KV grade FRLS 24.00 Mtr. 112.11

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class Rigid

PVC pipe and accessories (a) 2 wire 4 sq. mm

113 providing and erecting Mains with 1.1 KV grade FRLS 45.00 Mtr. 260.58

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class Rigid

PVC pipe and accessories (h) 4 wire 6 sq. mm

114 Supplying and erecting Flexible PVC insulated multi 24.00 Mtr. 46.46

strand multi core 1.1 kv grade ISI marked copper wires

of following size to be erected as directed. (e)

Sq.mm 3 core round PVC sheathed

115 Supplying & erecting approved make LAN cable of 120.00 Mtr 76.76

following size in existing pipe as per direction [D] CAT -

116 Providing & erecting Switch board for Computer or 4.00 Ea. 1133.22

electric apparatus consisting of following modular type

accessories mounted with PVC / Metallic

concealed/open box with single mounting base frame

covered with textured/metallic /white front

plate,modules erected with necessary connections as

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat.

117 Decorative call bell Ting-tong box type 250 volts 1.00 Ea. 71.71

complete erected

Item Rate In

Description of Item Quantity Unit Amount

No figures

118 Supplying and erecting LED indoor fittings with LEDs of 16.00 Ea. 535.30

wattage 0.2 Watt to 0.5 Watt assembled on single

MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. &

corrosion resistance with diffuser with company

mark/name 160V to 270V, Power Factor more than 0.95,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may

(A) Tube Light with integral driver (v) 36-40 Watts,

Surge-2 KV, IP-20, conventional 4 feet Cat-lll

119 Supplying and erecting led lamps with following wattage 1.00 Ea. 112.11

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 / B22 lamp

holders, pf >= 0.5 (A) LED Lamps integral type, with PC

diffuser suitable LAMP holder (ii) 5 to 8 watts Cat-III

120 Supplying & erecting approved make low noise 1.00 Ea. 1703.87

decorative exhaust fan having square frame ABS body

with inbuilt lowers & square frame. 200mm with

1350RPM Cat.II

121 Supplying and erecting LED street light / Flood light 3.00 Ea. 4997.48

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated

and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT

K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>

100 lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of

wattage capacity between the ranges shown.) (A) Street

Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage

protection. (ii) above 48 to 60 Watts Cat-lll

Item Rate In

Description of Item Quantity Unit Amount

No figures

122 (C) Post Top Lantern LED fitting comprises of finish cast 2.00 Ea. 4819.72

aluminum spigot and spun aluminum canopy fixed with

opal polycarbonate, pipe arrangement for vertical

mounting driver and accessories wired upto terminal

block.IP 65(ii)32-40W Cat-lll

123 Providing & erecting Approved make Power Saving 50 6.00 Ea. 1948.29

Watt Ceiling Fan with double ball bearing ISI mark with

Condenser 230 volt A.C. 50 Hz 1200 mm sweep

complete having 3blades with aluminium blades with

canopy & 30 cm. down rod erected with earthing.(Make

shall be approved by Engineer in charge))

124 Supplying and erecting 19 / 20 mm. nominal bore 6.00 Mtr. 108.07

Medium Class M.S. Pipe down rod erected duly painted

for fan complete with proper insulation without leakage

and earthing.

125 Supplying & erecting fan hook box of 10 mm M.S. round 6.00 Ea. 108.07

bar bounded to the RCC bars up to 50mm length each

side and pierced through a 16 Gauge M.S. box / Heavy

Duty PVC box complete erected concealed in Ceiling with

necessary finishing.

126 Providing 2.5mm.thick laminated acrylic sheet to cover 6.00 Ea. 18.18

the fan hook or Fan box.

127 Providing and erecting XLPE (IS:7098)(I)-88 ISI 114.00 Mtr. 126.25

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of

cables (B) 4 core 6 Sq. mm

128 Making trench in soft soil of suitable width of 90 cm deep 91.00 Mtr. 55.55

for laying cable or locating the fault all over the run and

back filling the same and making the surface as normal

129 Providing & laying approved make Double walled 91.00 Mtr. 62.62

corrugated pipes (DWC) of polyethylene(conforming to

IS 14930 II )with necessary connecting accessories of

same material at required depth in existing trench for

laying of cable. below ground / road surface for

enclosing cable (A)50 mm outer dia

130 Providing and, fixing heavy duty flange type brass cable 4.00 Ea. 38.38

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. (B) 2 to 4 core 6 Sq. mm

131 Solder less crimping type Aluminium lugs conforming to 48.00 Ea. 6.06

IS suitable for cable of following size evenly crimped

with high pressure tool & connected to switchgear

terminals with brass/cadmium plated nut bolts in an

approved manner. (A) 6 Sq.mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

132 providing and erecting Miniature circuit breaker single 17.00 Ea. 112.11

pole 6A to 25A suitable to operate on 240 V A.C. system

and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark

133 providing and erecting Approved make RCCBs 3.00 Ea. 2235.13

conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz.

having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed

(ii) 40Amps. DP Cat. III

134 Providing & erecting 415V MCB Four Pole Switch for 3.00 Ea. 638.32

Lighting Load (B curve) having 10KA breaking capacity

& confirms to IS :8828 in existing box having following

capacity (b)40 Amp. Cat.III

135 Providing and erecting Sheet Steel powder coated MCB 1.00 Ea. 2339.16

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to

IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for (B) three

phase incoming and single phase horizontal type

outgoing Per phase isolation type (PPI) (b) sheet steel

double door (i)4 way

136 Providing and erecting HOT deep Galvanised iron strip 7.00 Kg. 77.77

wire 8 to 16 SWG.

137 Providing and erecting Pipe type earthing having 150 2.00 Ea. 368.65

cms.long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

138 For using salt and charcoal / coke as required for pipe 2.00 Ea. 171.70

type earthing.

Item Rate In

Description of Item Quantity Unit Amount

No figures

139 Supplying & erecting earth pit of minimum bore 1.00 Ea. 4591.46

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer

pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for

following type of applications with chamber and heavy

duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of

installation duly stamped and signed by agency and

officer Incharge has to ensure the value of earthing

resistane mentioned in test Certificate) & having back

filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing as per

IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry

form, Sulphar content:- <2%(C) Back fill Compound :-

Earthing compound should be capable to retain moisture

for long time Necessary test report must be submitted

by Agency. (a) For Electrical Installation up to 440V in

normal soil Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

140 Supplying and erecting approved make Octagonal pole 3.00 Ea. 6874.06

made from HR sheet steel. The pole should be made as

per IS. and shall be coated with hot dip galvanizing as

per IS 2629/2633/4759, suitable suspend local wind

speed with integral Junction box consist of terminal plate

of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud type

terminal and arrangement for cable termination to be

erected With Suitable foundation (Included) as per

details given by manufacturer considering site

requirement. (C) 5 Mtr. Long 70 mm Top X 130 mm

bottom dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M16 Bolts and

600mm long with necessary G.I. J Bolts .Approx Pole

weight 46 kg

141 Supplying & erecting approved make SMC press 2.00 Ea. 515.10

moulded composite FRP. loop-in, loop-out approx. 2mm

thick box complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements

with mounting clamp with nuts, bolts & washers suitable

for erection on pole with cable clamps& earth bolt of

following size of box.(B) 250mm x 200mm x 100mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

142 Supplying and erecting Street light pole bracket 3.00 Ea 491.87

comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I. sleeve

tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and

bolts for fixing the brackets and having spread of 0.5 mtr.

Length with 110 deg.with vertical plane and suitable

welded stiffener reducer and nipple with check nut

complete painted with one coat.of Red oxide / PU base

primer and two coats of Aluminium / PU paint. paint

with following nos of arms. [A] Single Arm bracket

143 Supplying & erecting approved make IP 55 grade 1.00 Ea 13350.18

Company fabricated Timer Panel of following capacity

for switch On-Off street lights on time scheduling basis

made from 16G CRCA sheet duly epoxy power painted

inside and outside with hinged doors and locking

arrangement consisting of suitable size of 4 Pole MCB

and 4 pole contactor (cat-III)with analog time switch,

auto manual switch of same make and suitable input

and output Bakelite terminals and with door earthing

approved by Engineer in charge. (B) 40 Amp

144 Providing & erecting water cooler having storage 1.00 Ea. 55893.40

capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @

an ambient temp of 45˚ C. The outlet temp. of the water

should drop by 15˚C within a hour, The water cooler

should be comprising of hermetically sealed compressor,

fan motor, condensing unit, water tank surrounded by

evaporating, coil, thermostats, relay etc.complete with

necessary inlet & outlet connection. The body of water

cooler will be made from Stainless Steel.

145 Supplying & erecting 5 stage single reverse osmosis 1.00 Ea. 29187.99

water purification system with M.S. powder coated

frame, prefilter housing with 'O' ring presediment filter

GAC filter, carbon filter suitable buster DC pump

capacity 80 psi, mention with 40 psi inline type post

carbon filter auto low & high pressure switches with

following size of storage tank & LPH capacity & erected

as directed [C] 50 Ltr / Hr with 150 psi 2 nos booster

Total Rs.

Item Rate In

Description of Item Quantity Unit Amount

No figures

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and

words) of the estimated rate mentioned above. Amount of my /our

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

The Contractor shall exhibit a board with detailed specification and details of work as directed by the

1 Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

4 there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

Deputy Executive Engineer Executive Engineer

Vapi ( R & B ) Sub Division Valsad ( R & B ) Division

Vapi Valsad