Construction of Horticulture Development office building at Nerchwok Tehsil Balh Distt. Mandi (HP)

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation, trenches, drains (Any width or square metre on plan), including dressing of sides and ramming of bottoms, lift upto any height, including getting out the excavated soil and disposal of surplus excavated soil as directed in all kinds of classification, of soils such as pick work, jumper work, blasting work saturated soils including chiseling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases.

Centering and shuttering including strutting, propping etc. and removal of form work for :

Foundations, footings, bases for columns etcetera for mass concrete within all leads, lifts and carriage of materials and other incidentals or as per direction and satisfaction of Engineer-in-Charge.

Suspended floors, roofs, landings, balconies and access platform within all leads, lifts and carriage of materials and other incidentals or as per direction and satisfaction of Engineer-in-Charge.

Lintels, beams, plinth beams, girders, bressumers and cantilevers within all leads, lifts and carriage of materials and other incidentals or as per direction and satisfaction of Engineer-in-Charge.

Columns, Pillars, Piers, Abutments, Posts and Struts within all leads, lifts and carriage of materials and other incidentals or as per direction and satisfaction of Engineer-in-Charge.

Providing and laying in position cement concrete 1:6:12 ( one cement : six coarse sand : twelve graded, crushed stone aggregate 40mm (forty millimetre) nominal size) mechanically mixed and curing complete excluding the cost of centering and shuttering all work up to plinth level including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying in position cement concrete 1:5:10 ( one cement : five coarse sand : ten graded, crushed stone aggregate 40mm (forty millimetre) nominal size) mechanically mixed and curing complete excluding the cost of centering and shuttering all work up to plinth level including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying in position cement concrete 1:4:8 ( one cement : four coarse sand : eight graded, crushed stone aggregate 40mm (forty millimetre) nominal size) mechanically mixed and curing complete excluding the cost of centering and shuttering all work up to plinth level including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying in position reinforced cement concrete 1:2:4 (one cement : two coarse sand : four graded stone aggregate 20 mm (Twenty millimetre) nominal size), excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying reinforced cement concrete 1:1.5:3 (one cement : one and half coarse sand : three graded stone aggregate 20 mm (Twenty millimetre) nominal size) in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor all level, excluding cost of centering, shuttering, finishing and reinforcement including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete including cost of binding wire upto all floor level. Thermo-Mechanically Treated bars of grade Fe-500D or more including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Brick work with common burnt clay modular bricks of class designation 7.5 (Seven point five) in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Extra for laying brick work in or under water and/or liquid mud including cost of pumping or bailing out water and removing slush etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Random rubble masonry with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (One cement : six coarse sand : twelve graded stone aggregate 20mm (Twenty millimetre) nominal size) upto plinth level with Cement mortar 1:6 (One cement : six coarse sand) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Coursed rubble masonry (second sort) with hard stone of approved quality in foundation & plinth with Cement mortar 1:6 (One cement : six coarse sand) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Dry stone pitching 22.5 cm (Twenty two point five centimetre) thick including supply of stones and preparing surface complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing up to floor all level precast cement concrete solid blocks of 1:1.5:3 (one cement : one and half coarse sand : three graded stone aggregate 20 mm (Twenty millimetre) nominal size) including hoisting and setting in position with cement mortar 1:3 (One cement : three coarse sand), cost of required centering, shuttering complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Extra for forming cavity 5 cm to 11.5 cm (Five to eleven point five centimetre) wide in cavity walls with necessary weep and vent holes including use of cores and cost of providing and fixing bitumastic coated M .S. ties 300 mm (Three hundred millimetre) long of 25x3 mm (Twenty five into three millimetre) section at not less than 3 (Three) ties per sqm as per approved design complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws. (Glazing, paneling and dash fasteners to be paid for separately) for fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC 15) all complete as per architectural drawings including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws. (Glazing, paneling and dash fasteners to be paid for separately) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Anodised aluminium (anodised transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade AC15) all complete as per architectural drawings including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. (Cost of aluminium snap beading shall be paid in basic item) With float glass panes of 5 mm (five millimetre) thickness (weight not less than 12.50 (Twelve point five zero) kilogram per square metre) complete as per architectural drawings including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm (One point four millimetre) in both directions with wire of dia. 0.50 mm (Zero point five zero millimetre) With 12 mm (Twelve millimetre) mild steel U beading all complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 12 mm (Twelve millimetre) thick prelaminated particle board with decorative lamination on both sides flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 250x16mm (Two hundred fifty into sixteen millimeter) aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

200x10mm (Two hundred into ten millimeter)

150x10mm (One hundred fifty into ten millimeter)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

125mm (One hundred twenty five millimetre)

100mm (One hundred millimetre)

Providing and fixing Twin rubber aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 150mm (One hundred fifty millimetre) bright finished brass hard drawn hooks and eyes including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 150mm (One hundred fifty millimetre) bright finished brass double acting spring hinges with necessary brass screws etc.complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing cup board shutters with 25 mm (Twenty five millimetre) thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm (Twenty five millimetre) wide x 12 mm (Twelve millimetre) thick with necessary screws and bright finished stainless steel piano hinges, With decorative veneering on one side and commercial veneering on other side complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying vitrified floor tiles of 600X600mm (Six hundred into six hundred millimetre) size (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm (Twenty millimetre) thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (Three point three kilogramme per square metre) including grouting the joints with white cement and matching pigments etc., complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying vitrified tiles of 500X500mm (Five hundred into five hundred millimetre) size (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, in skirting, riser of steps, over 12 mm (Twelve millimetre) thick bed of cement mortar 1:3 (one cement : three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm (Three point three kilogramme per square metre) including grouting the joints with white cement and matching pigments etc., complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying vitrified tiles of 500X500mm (Five hundred into five hundred millimetre) size (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm (Six millimetre) thickness, including grouting of joints (Payment for grouting of joints to be made separately) complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and laying 8mm (Eight millimetre) thick wiparquet laminate ((Nature textured surface AC-4 1214 X 193 X8 mm (One thousand two hundred fourteen X One hundred ninety three X eight millimetre) flooring of approved brand and manufacture or equivalent wooden flooring laid over RCC/ Cement concrete base thinly coated with polythene and foam sheet cushion below as per specification complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing, in position concealed G.I. section for wall paneling using board of required thickness fixed on the 'W' profile (0.55 mm (Zero point five five millimetre) thick) having a knurled web of 51.55 mm (Fifty one point five five millimetre) and two flanges of 26 mm (Twenty six millimetre) each with lips of 10.55 mm (Ten point five five millimetre), placed @ 610 mm (Six hundred ten millimetre) centre to centre in perimeter channel having one flange of 20 mm (Twenty millimetre) and another flange of 30 mm (Thirty millimetre) with thickness of 0.55 mm and web of length 27mm (Twenty seven millimetre). Perimeter channel is fixed on the floor and the ceiling with the nylon sleeves @ 610 mm (Six hundred ten millimetre) centre to centre with fully threaded self-tapping dry wall screws. Board is fixed to the 'W' profile with 25 mm (Twenty five millimetre) countersunk ribbed head screws @ 200 mm (two hundred millimetre) centre to centre, the joints of the boards are finished with specially formulated jointing compound and 48mm (Forty eight millimetre) wide jointing tape to provide seamless finish Multipurpose cement board reinforced with suitable fibre cement screw 8 mm (Eight millimetre) thick Cement bonded wood particle board as per IS:14276 complete as per architectural drawings including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing 0.63 mm (Zero point six three millimetre) thick with zinc coating not less than 275 gm/ m² (Two hundred seventy five gramme per square metre) corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm (Eight millimetre) diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing 0.63 mm (Zero point six three millimetre) thick with zinc coating not less than 275 gm/ m² (Two hundred seventy five gramme per square metre) ridges or hips of width 60 cm (Sixty centimetre) overall width plain G.S. sheet fixed with polymer coated J or L hooks, bolts and nuts 8 mm (Eight millimetre) dia G.I. limpet and bitumen washers complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing 1.60 mm (One point six zero millimetre) thick with zinc coating not less than 350 gm/ m² (Three hundred fifty gramme per square metre) valleys of 90 cm (Ninety centimetre) wide overall in plain G.S. sheet fixed with polymer coated J, or L hooks, bolts and nuts 8 mm (Eight millimetre) dia G.I. limpet and bitumen washers complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm (One point six six to two point zero millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) complete with all accesoriees as required as per the direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidental charges.

Providing and fixing 0.63 mm (Zero point six three millimetre) thick with zinc coating not less than 275 gm/ m² (Two hundred seventy five gramme per square metre) 15 cm (Fifteen centimetre) wide, 45 cm (Forty five centimetre) overall semicircular plain G.S. sheet gutter with iron brackets 40x3mm (Forty into three millimetre) size, bolts, nuts and washers etc., including making necessary connections with rain water pipes complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing on wall face 110mm (One hundred ten millimetre) diametre unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten millimetre) gap for thermal expansion, (i) Single socketed pipes complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing on wall face Bend 87.5° (Eighty seven point five degree) 110 mm (One hundred ten millimetre) bend unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A,including jointing with seal ring conforming to IS : 5382, leaving 10 mm (Ten millimetre) gap for thermal expansion complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

15 mm (Fifteen millimetre) cement plaster on rough side of single or half brick wall in cement mortar 1:4 (one cement :four sand) complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

15 mm (Fifteen millimetre) cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement in cement mortar 1:4 (one cement :four sand) complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm (Zero point nine zero litre per ten square metre) over an under coat of primer applied @ 0.80 ltr/10 sqm (Zero point eight zero litre per ten square metre) of approved brand and manufacture complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Applying priming coat With ready mixed pink or Grey primer of approved brand and manufacture on wood work (hard and soft wood) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Painting (Two coats) with silicon & acrylic emulsion based water thinnable sealer of approved brand and manufacture on wet or patchy portion of plastered surfaces including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 1 mm (One millimetre), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Wall painting (Two coats) with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre (Fifty gramme per litre) of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Applying priming coats with water thinnable cement primer on wall surface having VOC (Volatile Organic Compound ) content less than 50 grams/litre (Fifty gramme per litre) primer of approved brand and manufacture including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/ litre (Fifty gramme per litre) and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm (One point four three litre per ten square metre). Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm (Zero point nine zero litre per ten square metre) including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Making plinth protection 50mm thick of cement concrete 1:3:6 (One cement : three coarse sand (zone - III) : six graded stone aggregate 20 mm (Twenty millimetre) nominal size) over 75mm (Seventy five millimetre) thick bed of dry brick ballast 40 mm (Forty millimetre) nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Making connection of G.I. distribution branch with G.I. main 25 to 40 mm (Twenty five to forty millimetre) nominal bore size by providing and fixing tee, including cutting and threading the pipe etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 (One)metre spacing. This includes testing of joints complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. INTERNAL WORK - EXPOSED ON WALL

1216 (16mm (Sixteen millimetre) OD) Pipe

1620 (20mm (Twenty millimetre) OD) Pipe

Providing and fixing 1216 (16 mm (Sixteen millimetre) OD) pipe Polyethelene-AluminiumPolyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g.elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00(One) metre spacing. This includes the costs of cutting chases and including testing of joints complete concealed work, including cutting chases and making good the wall etc. complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing White Vitreous china Orissa pattern W.C. pan of size 580x440 mm (Five hundred eighty into four hundred forty) with integral type foot rests water closet squatting pan (Indian type W.C. pan ) with 100 mm (One hundred millimetre) sand cast Iron P or S trap, 10 (Ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing White Vitreous China Flat back wash basin size 550x 400 mm (Five hundred fifty into four hundred millimetre) with single 15 mm (Fifteen millimetre) C.P. brass pillar tap with C.I. brackets, 15 mm (Fifteen millimetre) C.P. brass pillar taps, 32 mm (thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing C.P. brass toilet paper holder complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with ISI marked white solid plastic seat and lid, 10 (Ten) litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing PTMT soap Dish Holder having length of 138mm (one hundred thirty eight millimetre), breadth 102mm (One hundred two millimetre), height of 75mm (Seventy five millimetre) with concealed fitting arrangements, weighing not less than 106 gms. (One hundred six gramme) complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 600x120x5 mm (Six hundred into one hundred twenty into five millimetre) glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm (Forty millimetre) long screws, rawl plugs etc., complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 15mm (Fifteen millimetre) nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing PTMT 600 mm (Six hundred millimetre) long towel rail with total length of 645 mm (Six hundred forty five millimetre), width 78 mm (Seventy eight millimetre) and effective height of 88 mm (Eighty eight millimetre), weighing not less than 190 gms. (One hundred ninety gramme) complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm (Three hundred into three hundred millimetre) size (inside) the weight of cover to be not less than 4.50 kg (Four point five kilogramme) and frame to be not less than 2.70 kg (Two point seven kilogramme) as per standard design With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (Seven mpoint five) complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 8 mm(Eight millimetre) dia C.P. / S.S. Jet with flexible tube upto 1 (One) metre long with S.S. triangular plate to Eureopean type W.C. of quality and make complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 15 mm (Fifteen millimetre) nominal bore 30 cm (Thirty centimetre) length uplasticised PVC connection pipe with brass unions complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 20mm (Twenty millimetre) nominal bore uplasticised PVC connection pipe with brass unions complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

Providing and fixing 15 mm (Fifteen millimetre) nominal bore brass stop cock of approved quality complete including carriage of materials within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge.

KHEM CHAND