Construction of 2x8MVA, 33/11KV Substation (Indoor Type) at Kuraiya, Rudrapur

Amount

Cost of Earthing of Neutral and Body of Power Transformer and Earthing of 33KV,11 KV VCB Panel and 33KV Line L.A. (Schedule-1)

GI Earth Strip 65X6 mm weight 3.06 Kg /mtr

Highly Conductive Copper plate Electrode of size 600 X600X 6mm weight 21.5 kg/Plate(Purity should not be less than 99%)

Highly Conductive Copper earth Strip of size 75X6mm weight 4.6 Kg/mtr(Purity should not be less than 99%) for neutral of Power Transformer

Charcol Granual (about 1-3 cm granules size)

White Crystal Salt Granual (about 1-3cm granules size)

Cost of Delta Earthing by earth rod at 33/11 KV Sub Station.(Schedule-2)

MS Round 32mm dia, 6.32 Kg/mtr

G.I. Strip 65x6 mm.

G.I. Strip 50x6 mm.

Cost of Terminal Gantry with LA and Line Isolator (Schedule-3)

33KV,10KA Lightening Arrestor

33 KV 1250A vertical Type Line Isolator with earth switch

Cost of Transformer plinth for 8 MVA Transformer (Schedule-4)

Rail 90 Lbs

MS angle 50x50x6 mm for J-hooks

MS Bar, 12 mm Dia for Steel reinforcement

Cost of 8 MVA, 33/11 KV Transformer Structure only (Schedule-5)

M S angle 75X75X8 mm 4.5 M long for neutral structure

Cost of 33 KV Lightining Arrestor & its structure (Schedule-6)

M.S. Channel 125x65x6 mm

M.S. Angle 75x75x8 mm

33 KV,10 KA Lightening Arrester

MS Plate 300x300x8 mm.

M.S. bolts & nut with washers.

Cost of pole mounted 33/0.433 KV, 63 KVA station transformer (Schedule-7)

S.T. Pole 11 mtr. Long SP-55(Bottom Portion hot dip Galvanized)

M.S. Channel 100x50mm for top channel & dropper channel, bus isolator, fuse set, isolator handle & transformer base

33 KV Bus isolator

33 KV Fuse set

MS Earthing rod 20x2500mm

GI Wire 6 SWG

33 KV lightening arrestor

33 KV Aluminium 3Cx50 sq. mm. XLPE cable from Panel to station transformer Pole

LT XLPE Cable 4Cx25 Sq.mm. for Stn. T/F to ACDB.

33/0.433 KV, 63 KVA Station Transformer

M.S. Bolt & Nut off size

P.P. & Clamps for S.T. Pole SP-55 with nut & bolts

Clamp of required size for holding cable supporting angle, pipe, cable & bus isolator handle on double pole & bus bar gantry

Name plate for station transformer with clamp, nut & bolt

33 KV Danger board with clamp

Stone Pad 300x300x75

GI pipe 4" dia. 3mtr long

MS plate 300x300x8 mm

Cable jointing kit outdoor type suitable for 3Cx50 sq. mm. XLPE cable 33 KV.

Cable jointing kit indoor type suitable for 3Cx50 sq. mm. XLPE cable 33 KV.

Cost of Double Pole structure for 11 KV outgoing feeder (Schedule-8)

S.T. Pole 8.5 mtr. Long SP-23(Bottom Portion hot dip Galvanized)

M.S. Angle 65x65x6 for bracing set, 2.7mtr.x2

M.S. Channel 100x50mm for top channel & dropper channel & TPMO handle

M.S. Angle 75x75x6 mm for TPMO & Fuse set (4 nos.x2.24 mtr.)

M.S. Angle 50x50x6 mm for cable support 2.24 mtr.x3No

11 KV Polymer disc insulator B & S

11 KV disc fitting for weasal

Stay set GI 16x1800 mm

Stay wire GI 7/3.15mm 7/10SWG

MS Earthing rod 20x2500mm

GI Wire 5mm/6 SWG

9KV 5KA lightening arrestor (Polymer)

11 KV fuse set.

11 KV TPMO /GO Switch complete

M.S. Bolt & Nut Off size

P.P. & Clamps for S.T. Pole

Bracing Clamp for ST Pole

Stay clamp for ST Pole

Clamp of required size for holding cable supporting angle, cable & TPMO handle

Name plate of feeder

11 KV Danger board with clamp

Stone Pad 300x300x75

GI pipe 4" dia, 3mtr long

MS plate 300x300x8 mm

Cost of 33 KV bus bar & connectors (Schedule-9)

ACSR Panther conductor

33KV Polymer Pin Insulator with Pin

Connectors suitable for Panther

For LA

For Isolators

For T/F suitable for HT and LT side

For Station transformer

PG clamp for Panther Conductor

E-Clamps with nut & bolt

Cost of 33 KV Circuit Breaker Panels (Schedule-10)

33 KV, 1250 A 3 Ph. Indoor type VCB with required CT PT, protective relays, metering equipments, extendible both side bus bar etc. (SCADA OPERATED)

Incomer

Outgoing

33 KV Bus coupler with bus riser

PT Panel

Cost of 11 KV VCB panels (Schedule-11)

11 KV VCB I/C 500MVA, 800/400/5A, 110V AC

11 KV VCB FDR 350/500MVA, 400/200/5A, 110V AC

11 KV VCB Bus Coupler 350/500MVA

MS channel 100x50 mm

M.S. bolts & nut with washers.

Cost of 11 KV Cable Laying (Schedule-12)

33KV Aluminium 3Cx400sq. mm. XLPE cable from Pole to Incomer panel.(1cable from new proposed line and 1 cable from existing 33KV KM Paper mill feeder.)

33KV Aluminium 3Cx300 sq. mm. XLPE cable from outgoing panel to power transformer (02Nos.).

Cable Aluminium 3Cx400 sq. mm. XLPE 11KV from Power T/F to 11KV Incomer VCB

Cable Aluminium 3Cx300 sq. mm. XLPE 11KV from outgoing VCB to outgoing feeder poles

MS Channel 125x65 mm

MS Channel 100x50 mm

MS Angle 75x75x8 mm

Cable jointing kit outdoor type suitable for 3Cx400 mm XLPE cable 33 KV.

Cable jointing kit indoor type suitable for 3Cx400 sq. mm. XLPE cable 33 KV

Cable jointing kit outdoor type suitable for 3Cx300 mm XLPE cable 33 KV.

Cable jointing kit indoor type suitable for 3Cx300 sq. mm. XLPE cable 33 KV

Cable jointing kit outdoor type suitable for 3Cx400 mm XLPE cable 11 KV.

Cable jointing kit indoor type suitable for 3Cx400 sq. mm. XLPE cable 11 KV

Cable jointing kit outdoor type suitable for 3Cx300 sq. mm. XLPE cable 11 KV

Cable jointing kit indoor type suitable for 3Cx300 sq. mm. XLPE cable 11 KV

HT Cable warning tape

GI pipe 6" dia, 3mtr long

GI pipe 4" dia, 3mtr long

Clamp of MS Flat 50x6 mm. of suitable size for holding 6" & 4" dia. Pipe

Cost of LT power, control cable & its laying (Schedule-13)

LT Control Cable

10C x 2.5 Sq. mm.

4C x 2.5 Sq. mm.

2C x 2.5 Sq. mm.

MS Angle 50x50x6mm for cable trench

MS Angle 40x40X5mm for cable trench

MS Bar, 10 mm

Perforated tray for cable trench

400 mm width

200 mm width

100 mm width

Cost of Sub-station Lighting arrangement (Schedule-14)

8.0 mtr long ST pole SP-10 (Bottom portion hot dip)

LT PVC cable 4x10 sq. mm.

LT PVC cable 2x6 sq. mm. (Unarmed)

Stone pad 300x75 mm.

Iron clad 30 Amps water proof switch on the ST pole.

250W LED lamp with control gear & mounting accessories

150W, LED lamp with control gear & mounting accessories & 15 A MCB's

Cost of misc. items required for sub-station (Schedule-15)

24 V Battery charger with boost & trickle charge

24 V Battery set Maint. Free 150 AH

DCDB 24 V

110V Battery charger 300AH

110 V Battery set 300AH

DCDB 110 V

Instruction board 3’x2½’ of Flex board duly printed.

Single line diagram of size 3’x2½’ on flex board, duly printed.

Maximum & tripping display board of size 5’x3’ of mica board moulded with frame duly painted & writing.

Sub-station named board (Size 3'x2' of MS sheet & MS angle 45x45x5 mm, Height 1.5 mtr. Above ground level ), duly painted

Name plate of equipment TG, LI, BI, PI, BG, CT, PT, CB, LA etc. (Size 9"x5" with white base, red border & letter written in red color)

Sundries items Cable tie, Alu lug, Copper lug & HT, LT tape, pvc compound, ferrule, pvc flexible pipe, paint writing on panels, HT LT diff size cable gland.

Cost of toe wall & wiremesh fencing at substation (Schedule-16)

MS channel 100x50x6, (2.5x4x9.56) for gate

MS angle 40x40x5, 2.5 mtr long for stay

Fabrication & supply of Wire mesh frame made of 8 SWG wires frame of 40x40x5 mm angle M.S. (3mtr X 1.8 mtr), 35x5 mm MS flat & suitable 8mm plate including all material & labour charges

Fabrication & supply of 2 Nos, 2 mtr long, 1.8 mtr high wire mesh gate panels of 40x40x5 mm M.S.angle and 35x5 mm MS flat, with proper provision of locking arrangements in two piece. Including all material & labour charges.

Fabrication & supply of 1 Nos, 1 mtr long, 1.8 mtr high wire mesh gate panels of 40x40x5 mm angle M.S. (3 mrx1.8 mr), 35x5 mm MS flat, with proper provision of locking arrangements in one piece. Including all material & labour charges.

Cost of T&P & furniture for sub-station (Schedule-17)

Steel office table, Godrej, (5'x3')

Steel office table, Godrej, (4'x2.5')

Steel Almirah, Godrej,

Steel cabinet, Godrej,

Steel office chair, Godrej,

Shock treatment chart

Danger board

Shut down / Break down board (Bi-lingual Hindi & English)

HT Hand Gloves

Wall Clock

Insulated electrical Plier Taparia

D-Spanner Set Taparia

3 cells Torch

Pipe wrench, 12" Taparia

First aid Box

Earth chain brass 12 mtr. Length

5 KV Megger Digital

2.5kv Megger Digital

Earth Megger Digital

Dust bin branded make

Doormat (5'x3')

Cost of Fire safety equipments of sub-station (Schedule-18)

Rubber mat Class C 3 mm Synthetic Insulating Mat- Confirming to IS 15652 : 2006. Along the all equipments in Control Room.

Carbon dioxide (CO2) type fire extinguishers conforming to IS 2878 - 1976 and cylinders fully charged of 4.5 Kg capacity.

Foam type fire extinguishers, Portable type 5 lit capacity hanged on wall with bracket complete as required

Metal Fire bucket Filled with sand

Fire bucket stand of Chuggi type of MS angle 50x50x6 mm with top covered by MS sheet 2 mm. thickness and Duly painted with red color including cost of all material, fabrication etc. complete work

Cost of Bus Isolator & its structure (Schedule-19)

33KV Bus Isolator 800A

M.S. Channel 125x65 mm

M.S. Angle 75x75x8 mm

MS Angle 50x50x6 mm

M.S. Flat 50x6 mm.

M.S. bolts & nut with washers.

Cost of 11KV Capacitor Bank (Schedule-20)

10MVAR Capacitor Bank

Testing of Substation.

Description of Work / Item(s)

Amount

Cost of Earthing of Neutral and Body of Power Transformer and Earthing of 33KV,11 KV VCB Panel and 33KV Line L.A. (Schedule-1)

Earth Pit of the size of 1-meter diameter and 3-meter depth shall be excavated, after depth of 3 meter the size of excavation shall be 900X300X900mm depth.Plate Electrodes shall be instralled in vertical position.At bottom 150mm layer of salt and charcoal power shall be installed, then Plate shall be installed.The plate/pipe electrode, as far as practicable, shall be buried below permanent moisture level but in no case less than 2.5 meter below finished ground level.600 mm × 600 mm × 6 mm copper plate buried at a depth of 8 ft in vertical position with the pit filled with alternate layers of charcoal and salt up to 4 ft from bottom.The copper plates shall be connected to 65X6mm GI earth strip and 75X6 mm copper strip by 6'' long brass nuts and bolts, check nuts & washer no less than two points and the joints shall be protected by heavy coat of bitumen.After installation the earth result should be less than 1 Ohm.

Laying of G.I. Strip 65X6 mm with proper L shape bending included with face to face welding and jointing with 6'' long brass nuts and bolts, check nuts & washer.

Laying of Copper Strip 75X6 mm with proper L shape bending included with face to face Jointing with 6'' long G.I. nuts and bolts, check nuts & washer.

Concrete Chamber with cast Iron cover

Installation of GI Pipe of size 60X3 mm (pipe Should contain holes of 12mm diameter in zig zag manner starting from 15cm away from bottom to 2m height (at least 1 Liter water holding capacity)) with funnel and connecting accessories for watering including supply of material.

Finishing of surface after completion of Earthing work

Turfing in 1:3:6 ratio

Gravelling work

Cost of Delta Earthing by earth rod at 33/11 KV Sub Station.(Schedule-2)

Making of Delta/Bridge earthing for structure i.e. 33 KV Bus Isolator,33 KV LA, 11 KV LA, ACDB, DCDB, fencing.

Earthfilling in yard

Cost of Terminal Gantry with LA and Line Isolator (Schedule-3)

Febrication and erection charges of 33KV Terminal D/P 8.5mtr long of RS joist 150x150mm with double top channel 125x65mmx3.2 mtr with bracing set and suitable channel mounted for fixing 33KV Vertical isolator and Lightening arrestor including supply of all materials.

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Cost of Transformer plinth for 8 MVA Transformer (Schedule-4)

Fabrication of Rail 90 Lbs, cutting of MS angle 50x50x6 mm and MS Bar 12 mm

Excavation of earth in mixed soil

Brick work in 1:4

Plaster in 1:4

Cost of 8 MVA, 33/11 KV Transformer Structure only (Schedule-5)

Shifting of transformer from road side to transformer plinth through chain pully, lift pully and slippers etc.

Erection of transformer by fixing all accessories, tank, filling of transformer oil etc.

Fabrication & erection of neutral structure including excavation & grouting in CC 1:4:8

Safe cartage of 8 MVA Power transformers from nearest UPCL store to work site

Cost of 33 KV Lightining Arrestor & its structure (Schedule-6)

Fabrication charges of structure as per approved drawing

Excavation of earth in mixed soil

Grouting of structure with C.C. in 1:3:6 ratio

Cement Plaster 1:4, on top & side walls

Erection charges of structure

Fixing and erection charges of Lightening arrestor

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Cost of pole mounted 33/0.433 KV, 63 KVA station transformer (Schedule-7)

Excavation of earth

Cement concreting of Double pole 1:4:8

Cement Plaster in 1:4

Fabrication charges of channel

Erection of Double pole complete with all fittings, channels etc. complete work

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Erection of 33/0.433 KV station transformer on double pole with all accessories complete work

Laying, spreading & jointing of LT cable by using propers ties, lugs, connectors, cable glands in cable trench and equipments..

Laying of 33KV Cable by excavation of cable trench in mixed soil, filling of the sand upto the height 250mm from the bottom most level of the cable trench thereafter properly laying of the cable by placing bricks on both side of the cable than re-filling of the sand from the top so as to cover the cable completely and then placing the bricks on the top of the covered cable, spreading of cable warning tape & covering of the trench completly with mixed soil including cost of sand, bricks, etc.

Filling of cable jointing kit 33 KV indoor and outdoor type

Erection of vertical 33 KV bus isolator on double pole SP-55 complete by assembeling, fixing of operating handle, pipe, clamps, pins etc for smooth operation of the isolator.

Erection of 33 KV fuse set on double pole SP-55.

Cost of Double Pole structure for 11 KV outgoing feeder (Schedule-8)

Excavation of earth

Cement concreting of Double pole 1:4:8

Cement Plaster in 1:4

Fabrication charges of channels & angle

Erection of Double pole complete with all fittings, accessories, stays & earthing.

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Cost of 33 KV bus bar & connectors (Schedule-9)

Flexible copper connection on neutral bushing of power & station transformer 500X50 mm heavy duty with copper lug at ends.

Labour charges for drawing bus-bar & making connection in each equipment, main & auxilary bus bar.

Cost of 33 KV Circuit Breaker Panels (Schedule-10)

Cartage of panels from road side to SGR

Placing of panels on specific place over SGR trench on MS Channels and fixing of pannels with nut & bolts.

Making electrical connection of panels by control wiring complete with & VCB etc.

Cost of 11 KV VCB panels (Schedule-11)

Manual shifting of 11 KV VCB from road side to SGR

Fixing and erection of 11KV Panels

Fabrication of MS channel

Cost of 11 KV Cable Laying (Schedule-12)

Laying of 33 KV/ 11 KV Cable by excavation of cable trench in mixed soil, filling of the sand upto the height 250mm from the bottom most level of the cable trench thereafter properly laying of the cable by placing bricks on both side of the cable than re-filling of the sand from the top so as to cover the cable completely and then placing the bricks on the top of the covered cable, spreading of cable warning tape & covering of the trench completly with mixed soil including cost of sand, bricks, etc.

Filling of cable jointing kit 33 KV indoor & outdoor type

Filling of cable jointing kit 11 KV indoor & outdoor type

Fabrication charges of MS items

Fixing of GI Pipes

Erection of cable supporting MS Channel & angle

Cost of LT power, control cable & its laying (Schedule-13)

Fabrication charges of MS item

Making cable trench of size 50x30cm including fabrication, fixing of MS angle 40x40x5 mm size (excluding the cost of MS Angle/ MS bar) on side edge with all excavation, CC work, brick work, fixing of cable support angle one/two tier as required with stopper arrangement at 0.5 mtr gap throughout the length of the trench, making of cable trench covers with MS Bar welded mesh angle frame of MS angle 40x40x5 mm. with lifting hooks, fixing of perforated tray complete as per drawing including cost of sand, cement, bricks, metal (gitti) etc.

Laying, spreading & jointing of LT control cable by using propers ties,lugs, connectors, cable glands in cable trench and equipments..

Cost of Sub-station Lighting arrangement (Schedule-14)

Excavation of earth

Cement concreting in 1:4:8 ratio

Erection of ST Pole SP-10 and fitting of accessories.

Painting of ST Pole with one coat of red oxide primer and two coat of Aluminium paint

Erection of 250 watt & 150 watt lighting equipment & all its accessories

Laying of LT PVC cable 4x10 sq. mm. in soil & back filling of sand.

Cost of misc. items required for sub-station (Schedule-15)

Erection of 24 V Battery charger with boost & trickle charge

Erection of 24 V Battery set Maint. Free

Erection of DCDB 24 V

Erection of 110V Battery Charger

Erection of 110 V Battery set

Erection of DCDB 110 V

Erection of ACDB

Erection of Name plates, instruction board, SLD, Max., Min. board etc.

Erection of substation name board by grouting in CC 1:4:8 ratio

Cost of toe wall & wiremesh fencing at substation (Schedule-16)

Erection of stays post of 40x40x5 mm angle 2.5 mtr long. with required CC 1:4:8 work of size .5x.5x.5

Fabrication & Erection of M.S. Channel 125x65mm size 3.5x2 for fixing of wire mesh gate including grouting of the pillar.

Erection, grouting & fixing of pre-fabricated wire mesh of size 3x1.8 mtr with proper levelling and alignments on toe wall with the CC 1:3:6 in size 0.45x0.45x.60 and all the pieces duly weldded with angle joints. Including all material, labour charges & tack welding.

Painting of both side of wiremesh fencing with one coat of red oxide paint and two coat of Bus green paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Painting of stays with one coat of red oxide paint and two coat of Bus green paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of red oxide, paint.

Cost of T&P & furniture for sub-station (Schedule-17)

Fixing, placing and erection of T&P and furniture material

Cost of Fire safety equipments of sub-station (Schedule-18)

Instalation/Mounting of Fire Extinguishers

Cost of Bus Isolator & its structure (Schedule-19)

Fabrication charges of structure as per approved drawing.

Excavation of earth in mixed soil

Cement concreting in 1:3:6 ratio

Cement Plaster 1:4 on top & side walls

Erection charges of isolator structure

Erection charges of Isolator complete by assembeling, fixing of operating handle, pins etc for smooth operation of the isolator.

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint of best quality I.S.I. mark Dulux, Burger, Asian make including cost of all material.

Cost of 11KV Capacitor Bank (Schedule-20)

Construction of Plinth for all equipment.

Fixing and erection of Capacitor Bank.

Fixing and erection of 11KV,630Amp off load Isolator with earth switch and mounting structure

Fixing and erection of Indoor type automatic power factor controller

Fixing and erection of 11KV Outdoor VCB switchgear including fixing of all cable joint

Filling of cable jointing kit 11 KV indoor & outdoor type

Laying of power and control cable in trench including all connections.

Description of Work / Item(s)

Amount

Cost of Single pole structure on ST pole SP-55, 11 mtr long as per annexure-1

ST Pole SP- 55, 11 mtr long (Bottom portion hot dip galvanised)

X arm channel 100x50mm V type for 33 KV

33KV 10KN Polymer Pin insulator with Pin

Clamp for V type cross arm with nut and bolt

F Bracket with pp clamp and Nut& Bolt

Earth wire clamp with nut and bolt

Stone pad

Danger bord and Number plate with clamp

Barbed wire

Cost of Single pole structure on ST pole SP-72, 13 mtr long as per annexure-2

ST Pole SP- 72, 13 mtr long (Bottom portion hot dip galvanised)

33KV streight/L type X arm (125x65mm) 2.4x13.5

Supporting angle for top channel 65x65x6mm (1.5x2x6.5)

33KV 10KN Polymer pin insulator with pin

Top channel clamp with bolts and nut

Supporting clamp for top channel

Earth wire clamp with nut and bolt

Bolts and nuts

Stone pad

Danger bord and Number plate with clamp

Barbed wire

Cost of Double pole structure on ST pole SP-55, 11mtr long as per annexure-3

ST Pole SP- 55, 11 mtr long (Bottom portion hot dip galvanised)

MS channel 125x65mm 3.2mtr long 13.5kg/mtr (3.2X13.5)

33 KV Polymer disc insulator B&S Type

Disc fitting (B&S) type for dog conductor

33KV 10KN Polymer pin insulator with pin

MS angle 65x65x6mm 3.8mtr long 2x3.8mm @6.5kg/mtr

Top channel clamp with bolt and nut

E clamp with bolt & nut

Earth wire clamp with bolt & nut

Bolt and nut

Stone pad

PG clamp for Dog conductor

Bracing set clamp 135mm

Bracing set clamp 165mm

Danger bord and Number plate with clamp

Barbed wire

Cost of Double pole structure on ST pole SP-72, 13mtr long as per annexure-4

ST Pole SP- 72, 13 mtr long (Bottom portion hot dip galvanised)

MS channel 125x65mm 3.2mtr long 13.5kg/mtr (3.2X13.5)

33 KV Polymer disc insulator

Disc fitting (B&S) type for dog conductor

33KV 10KN Polymer pin insulator with pin

MS angle 65x65x6mm 3.8mtr long 2x3.8mm @6.5kg/mtr

Top channel clamp with bolts and nut

E clamp with bolts & nuts

Earth wire clamp with bolts & nuts

Bolts and nuts

Stone pad

PG clamp for Dog conductor

Bracing set clamp 135mm

Bracing set clamp 165mm

Danger bord and Number plate with clamp

Barbed wire

Cost of Tri pole structure on ST pole SP-55 11mtr long as per annexure-5

ST Pole SP- 55 ,11.0 mtr long (Bottom portion hot dip galvanised)

MS channel 125x65mm 3.2mtr long 13.5kg/mtr (3.2X3X13.5)

33 KV Polymer disc insulator

Disc fitting (B&S) type for dog conductor

33KV 10KN Polymer pin insulator with pin

MS angle 65x65x6mm 3.8mtr long 6x3.8x6.5mm @6.5kg/mtr

Top channel clamp with bolts and nut

E clamp with bolts & nuts

Earth wire clamp with bolts & nuts

Bolts and nuts

Stone pad

PG clamp for dog conductor

Bracing set clamp 135mm

Bracing set clamp 165mm

Danger bord and Number plate with clamp

Barbed wire

Cost of Four pole structure on ST pole SP-55 11mtr long as per annexure-6

ST Pole SP- 55 ,11.0 mtr long (Bottom portion hot dip galvanised)

MS channel 125x65mm 3.2mtr long 13.5kg/mtr (3.2X4X13.5)

33 KV Polymer disc insulator

Disc fitting (B&S) type for dog conductor

33KV 10KN Polymer pin insulator with pin

MS angle 65x65x6mm 3.8mtr long 8x3.8x6.5mm @6.5kg/mtr

Top channel clamp with bolts and nut

E clamp with bolts & nuts

Earth wire clamp with bolts & nuts

Bolts and nuts

Stone pad

PG clamp for Panther conductor

Bracing set clamp 135mm

Bracing set clamp 165mm

Danger bord and Number plate with clamp

Barbed wire

Cost of Stay for 33 KV SP/DP/TP/FP per annexure-7

Stay set GI 20x1800 mm

Stay wire GI 7/4mm 7/8 SWG

Stay clamp with nut & bolt

Stay Insulator of size 140x85mm

Cost of Earthing for 33 KV SP/DP/TP/FP per annexure-8

Earthing rod 20x2500mm

GI wire 5mm/6 SWG

Bolt & nut 150x12mm

Bolt & nut 50x16mm

Cost of Stud pole SP-55 for 33 KV Pole STP 11.0M,13.0M SP/DP/TP/FP per annexure-9

ST Pole 11m long SP-55 (Bottom portion hot dip galvanised)

Stone pad 300x300x75mm

Stay clamp with nut & bolt

11KV, LT, Road & river crossing guarding as per Annexure-10

MS Angle 75x75x8mm 3.75Mtr long=3.75x2x8.9+3%

GI wire 6 SWG=50X4+3%=206mtr @150Kg/Km (Avg. Span 50 Mtr)

GI wire 8 SWG=4MX25 @100Kg/Km

PP & clamps with N&B

Eye Bolt 190X16mm with nut

Cost analysis of 5.6 Km overhead 33 KV line by ACSR Dog Conductor as per Annexure-11

ACSR Dog conductor (1X3+3% C&W)

Earth wire GI 7/1.6mm 16 SWG (1x110Kg+3% C&W)

Cost of cable stand as per Annexure-12

MS Angle 65x65x6mm 8x4x6.5

MS Angle 50x50x6mm 0.4x40x5

Bolt and Nut

Clamp for holding cable made of MS flat 50x6mm

GI Strip 50x6mm 11x2.5

Cost of D/Ckt underground 33KV cable line 1.9 Km as per Annexure-13

Cable AL 3X400 Sq.mm XLPE 33KV

Cable jointing kit for 33 KV XLPE 3x400 Sqmm Outdoor

MS Channel 100x50mm (3.2X6X10Kg/mtr)

Holding PP Clamp with nut& Bolt

Straight Through Cable jointing kit for 33 KV XLPE 3x400 Sqmm

Description of Work / Item(s)

Amount

Cost of Single pole structure on ST pole SP-55, 11 mtr long as per annexure-1

Excavation of earth pit.

Erection of Single pole complete with all fittings & accessories.

Grouting of pole in CC ratio 1:4:8 cement ,sand, 20mm gauge stone ballast (0.45x0.45x1.8)-(3.14x0.075x0.075x1.8)mtr

Muffing of Pole in 1:3:6 CC size of (0.45x0.45x 0.4)-3.14x0.075x0.075x0.4) mtr.

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint including cost of paint.

Cost of Single pole structure on ST pole SP-72, 13 mtr long as per annexure-2

Excavation of earth pit.

Erection of Single pole complete with all fittings & accessories.

Grouting of pole in CC ratio 1:4:8 cement ,sand, 20mm gauge stone ballast (0.45x0.45x1.8)-(3.14x0.075x0.075x1.8)mtr

Muffing of Pole in 1:3:6 CC size of (0.45x0.45x 0.4)-3.14x0.075x0.075x0.4) mtr.

Fabrication charges of channels & angle

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint including cost of paint.

Cost of Double pole structure on ST pole SP-55, 11mtr long as per annexure-3

Excavation of earth pit.

Grouting of pole in CC ratio 1:4:8 cement ,sand, 20mm gauge stone ballast (0.45x0.45x1.8)-(3.14x0.075x0.075x1.8)x2

Muffing of Pole in 1:3:6 CC size of (0.45x0.45x 0.4)-(3.14x0.075x0.075x0.4)x2 mtr.

Erection of Double pole complete with all fittings & accessories.

Fabrication charges of channel & angle

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint including cost of paint.

Cost of Double pole structure on ST pole SP-72, 13mtr long as per annexure-4

Excavation of earth pit.

Grouting of pole in CC ratio 1:4:8 cement ,sand, 20mm gauge stone ballast (0.45x0.45x1.8)-(3.14x0.075x0.075x1.8)x2

Muffing of Pole in 1:3:6 CC size of (0.45x0.45x 0.4)-(3.14x0.075x0.075x0.4)x2 mtr.

Erection of Double pole complete with all fittings & accessories.

Fabrication charges of channel & angle

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint including cost of paint.

Cost of Tri pole structure on ST pole SP-55 11mtr long as per annexure-5

Excavation of earth pit.

Grouting of pole in CC ratio 1:4:8 cement ,sand, 20mm gauge stone ballast (0.45x0.45x1.8)-(3.14x0.075x0.075x1.8)x3

Muffing of Pole in 1:3:6 CC size of (0.45x0.45x 0.4)-(3.14x0.075x0.075x0.4)x3 mtr.

Erection of Tripole complete with all fittings & accessories.

Fabrication charges of channels & angle

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint including cost of paint.

Cost of Four pole structure on ST pole SP-55 11mtr long as per annexure-6

Excavation of earth pit.

Grouting of pole in CC ratio 1:4:8 cement ,sand, 20mm gauge stone ballast (0.45x0.45x1.8)-(3.14x0.075x0.075x1.8)x4

Muffing of Pole in 1:3:6 CC size of (0.45x0.45x 0.4)-(3.14x0.075x0.075x0.4)x4 mtr.

Erection of Four pole complete with all fittings & accessories.

Fabrication charges of channels & angle

Painting of structure with one coat of red oxide paint and two coat of Aluminium paint including cost of paint.

Cost of Stay for 33 KV SP/DP/TP/FP per annexure-7

Exacavation of earth for stay pit of size 0.6x0.6x1.5 mtr in all types of soil including proper dressing of sides and ramming of bottom including getting out the exacavted soil and disposel of surplus exacavated soll as directed complete work.

Grouting of stay in size 0.6x0.6x0.3 in CC ratio 1:4:8 block including cost of cement sand and stone ballast back filling of soil and boulders in pit and ramming and proper alignment, leveling.

Fixing, tightening and nozzling of stay wire with pole and stay rod.

Cost of Earthing for 33 KV SP/DP/TP/FP per annexure-8

Earthing of support with MS Earth rod of 2.5 Mtr long incuding exavation of pit 0.6mtr below ground level and ramming of MS rod upto full length and connecting the earth electrode with pole by GI wire and nut & bolt.

Cost of Stud pole SP-55 for 33 KV Pole STP 11.0M,13.0M SP/DP/TP/FP per annexure-9

Civil work CC 1:4:8=0.45x0.45x1.8

Erection of stud stay

11KV, LT, Road & river crossing guarding as per Annexure-10

Fabrication charges

Labour charges for Guarding

Cost analysis of 5.6 Km overhead 33 KV line by ACSR Dog Conductor as per Annexure-11

Laying,Sagging and Stringing of 3Phase 4wire line by ACSR Dog conductor and earth wire GI 7/16 as earth wire with route clearence.

Cost of cable stand as per Annexure-12

Exacavation of earth in all type of soil 4x0.6x0.6

Fabrication Charges

Grouting of cable stand in CC 1:3:6 (0.6X0.6X4) including muffing.

Earthing of cable stand structure with making triangle GI Strip bridge including supply of all material.

Painting charges of cable stand complete with one coat of red oxide and two coat of Aluminium paint.

Cost of D/Ckt underground 33KV cable line 1.9 Km as per Annexure-13

Fabrication Charges of MS items

Digging open trench 120cm deep and 45cm wide and prepare 10 cm thick fine sand cushion and then Laying of 33KV 3X400Sqmm cable over this cushion,then covered the cable with another 10cm thick sand layer.The trench is then covered with brick and other material covering all around cable protected on sides and top as per site requirement.

Making trench with trenchless technology for 33KV at road crossing with laying of cable in HDPE Pipe/GI Pipe.

Laying of cable for loop etc.

Supply and Laying of of HDPE pipe 160mm outer dia,6mm thickness.

Supply and fixing of GI Pipe (with Socket) 4or 5 inch dia at points of road crossing, cable rising etc ( B Class)

Fixing of 33 KV 3core XLPE Outdoor cable jointining kit of 400 Sqmm

Fixing of MS Channel,Holding clamp for cable support.

Making pit of size 5X2X2 mtr for filling and fixing of 33KV Straight through joint kit with back filling,ramming and compaction upto complete restoration.

Description of Work / Item(s)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :Shelves (Cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for :Lintels, beams, plinth beams, girders, bressumers and cantilevers

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab upto 0.50 sqm

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite work

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.Second class teak wood 35 mm thick

Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :250x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :200x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :100x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :250x16 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :(200x10mm)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :(150x10mm)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :125mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws :35 mm thick shutters with ISI marked M.S. pressed butt hinges bright finished of required size Second class teak wood

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile B Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Profile C Fixing with adjustable lugs with split end tail to each jamb

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Galvanised M.S. Wire gauze with 0.63 mm dia wire and 1.4 mm aperture on both sides

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with :5.5 mm thick glass panes

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate

Providing and fixing glass strips in joints of terrazo/ cement concrete floors.40 mm wide and 4 mm thick

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joint with white cement & matching pigmentsetc. complete.Size of Tile 600x600 mm

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (75mm diameter)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.( 110mm diameter)

12mm cement plaster of mix: 1:4 (1cement : 4coarse sand)

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two or more coats) over and including water thinnable priming coat with cement primer

Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Supplying and stacking at site.Good earth

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing terminal guard : 75 mm Sand cast iron S&S as per IS - 1729

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outletSand cast iron S&S as per IS: 3989

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 15 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40 mm nominal outer dia Pipes

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making ecessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.(15 mm nominal bore)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15mm nominal bore

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

P/Fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Engaging suitable Beldar for petty works (Basis rate labour)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required. GROUP B

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required2*2.5 Sq.mm*1*2.5Sq mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required2*4 Sq.mm*1*4Sq.mm earth wire

S/f stepped type electronic fan regulator on the existing modular plate switch box including nnections but excluding modular plate etc. as required.

Supplying and fixing metal box of 180mm X 100mm X 60mm deep (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including providing and fixing 6 pin 5/6 & 15/16 amps socket outlet and 15/16 amps piano type switch, connection, painting etc. as required.

Installation, testing and commissioning of pre-wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Upto 450 mm sweep

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.2 run of cable

S/F following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted ncluding earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way , Double door

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supply and Placing single phase panel board/ box crompton greaves make or equivalent make with flat submersible copper cable 1.50 sqm (panel to submersible pump set ) including auto start stop button, push button for volt meter indicator complete in panel board/ box for submersible pump set Installation 32mm outlet size submersible pump set.

Supplying of 20Watt LED Tubelight Philips or equivalent make as approved by E.I. S.E. letter no-832 /ECC/D.Dun/Extra Item Dated-29-08-2022

"Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos.blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. file no-E-9059857/9(new technology)/C.E.(Ren.)CSQ/2019 Dated-18/11/2019"

Supplying of Exhaust Fan 250mm sweep of Orient or equivalent make as approved by E.I. S.E. letter no-832 /ECC/D.Dun/Extra Item Dated-29-08-2022

Supplying of Exhaust Fan 450mm sweep of Orient or equivalent make as approved by E.I.

Supply and Placing 20/40 LTR Storage Water Cooler SS Body USHA make or Equivalent make approved by E.I. S.E. lettre No.- 1154/ECC/D.Dun/Extra item Dated- 15.11.2022

Supply and Installation Water Purifier (15 LPH) Kent or Equivalent make approved by E.I. S.E. lettre No.- 1154/ECC/D.Dun/Extra Item Dated- 15.11.2022

Description of Work / Item(s)

Amount

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting propping etc. and removal of form for: Lintels, beams, plinth beams girders, bressumers and cantilevers,

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

12mm cement plaster of mix: 1:6 (1cement :6coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix :1:6 (1 cement: 6 coarse sand)

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/ 10 sqm

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Supplying and stacking at site.Good earth

Supply of Stone Aggregate (Single size) : 20 mm nominal size

Engaging suitable Beldar for petty works (Basis rate labour)

M/s Kashmirilal Constructions Pvt. Ltd.

SURYACONENGINEERS LLP

RP INFRAPOWER PVT LTD

Mishrilal Associates Pvt. Ltd.

Ashish Electricals

SURYACONENGINEERS LLP

M/s Kashmirilal Constructions Pvt. Ltd.

Mishrilal Associates Pvt. Ltd.

Ashish Electricals

M/s Kashmirilal Constructions Pvt. Ltd.

RP INFRAPOWER PVT LTD

Mishrilal Associates Pvt. Ltd.

M/s Kashmirilal Constructions Pvt. Ltd.

Mishrilal Associates Pvt. Ltd.

SURYACONENGINEERS LLP

RP INFRAPOWER PVT LTD

Ashish Electricals

Mishrilal Associates Pvt. Ltd.

SURYACONENGINEERS LLP

RP INFRAPOWER PVT LTD

M/s Kashmirilal Constructions Pvt. Ltd.

Ashish Electricals

RP INFRAPOWER PVT LTD

Mishrilal Associates Pvt. Ltd.

RP INFRAPOWER PVT LTD

Ashish Electricals

M/s Kashmirilal Constructions Pvt. Ltd.

Mishrilal Associates Pvt. Ltd.