PROVN OF PARKING SHEDS FOR SPECIALIST VEHICLES IN TECH AREA AND PARKING SHED IN FRONT OF HANGER NO 4 AND 5 AT AF STN JODHPUR

Amount

Demolition of cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) and disposing off debris outside MD land complete all as specified and as directed by Engr-in-Charge.

Excavation over area n.exc 1.5m deep and getting out in soft / loose soil completed all as specified and directed.

Excavation over areas not exc 1.5m wide and n. exc 1.5m in depth, for foundation, etc. or for shafts, wells, cesspits, manhole, pier holes, etc. n exc 10 Sqm on plan and exc 1.50m and n exc 3.00m in depth and getting out in Soft / loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. and getting out in soft /loose soil completed all as specified and directed.

M&L for PCC 1:4:8 type D-2 (40mm graded stone aggregate) in foundation, sub base, filling and mass concrete completed all as specified and directed.

M&L for RCC M-25 (design mix) (using 20mm graded stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for RCC M-25 (design mix) (using 20mm graded stone aggregate) in columns, pillars, piers, posts and struts completed all as specified and directed.

M&L for RCC M-25 (design mix) (using 20mm graded stone aggregate) in beams, cantilevers, bressummers, over 1.5m span completed all as specified and directed.

M&L for RCC M-25 (design mix) (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like completed all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

All as per item No 10 above, but 8mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for preparing new surfaces of roof and applying two coats of Polyurethane (PU) acrylic based water proofing liquid compound over and including a coat of diluted elastomeric self primer and reinforcement fabric sheet as per manufacturer’s instruction to stop leakage / seepage from roof / wall complete all as specified and directed by the Engineer-in-charge.

M&L for 10mm thick rendering in cement mortar 1:3 with water proofing compound @ 3% by weight of cement, on existing concrete surfaces on roof, finishing even and smooth without using extra cement complete all as specified & directed. (Note : water proofing compound shall be measured and paid separately)

Supply only integral water proofing compound all as specified & directed.

M&L for pre-cast cement concrete1:2:4 type B1 (20mm graded stone aggregate) block masonry with solid blocks, exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and directed.

M&L for rendering 12mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) completed all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair face of brick-work or concrete surfaces including finish even and smooth (without using extra cement) completed all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 on fair concrete surfaces in ceiling finished even and smooth (without using extra cement) completed all as specified and directed.

M&L for 75mm thick plain cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) as in plinth protection laid in panels including necessary fromwork, finished even and smooth without using extra cement complete all as specified and directed.

M&L for hardcore (broken stone or boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-40 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L preparing undecorated newly plastered surfaces of wall and apply two coats of distemper oil emulsion over and including one coat of wall primer over and including one coat of 3mm thick wall care putty of approved colour complete all as specified and directed.

M&L for preparing undecorated newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Material & Labour for applying two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and directed.

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm of soft/loose soil complete all as specified and directed.

Removing excavated soil out side MOD land and deposited at a place identyfied by the contractor at his own cost complete all as specified and directed.

Material & labour precast cement concrete type B-0 1:2:4 using 12.5 mm graded stone aggragate as in louvers and jallies, 45 mm thick (measured solid) incl. all mould set in CM 1:4 complete all as specified and directed.

M&L for PCC 1:2:4 type B-2 (40mm graded stone aggregate) in foundation, sub bas, filling and mass concrete completed all as specified and directed.

S&F Pre-painted galvalume (sand colour) aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume (sand colour) aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for surface dressing n.exc (not exceeding) 15 cm deep and getting out soft / loose soil complete all as specified and directed.

M&L for framed work such as roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces ,cleats etc and similar work conforming to Fe-410 W, Gde-E-250 Quality-A complete all as specified & directed.

M&L for plates (plain or chequered ) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment and similar work conforming Fe-410 W, Gde-E-250 complete all as specified & directed.

M&L for 5mm thick ACP sheet fixed with high Intensity prigmetic (HIP) blue colour tap for sign board in letter in white colour complete all as specified and directed.

M&L 50mm thick sand filling under floor or below interlocking tiles incluiding watering and consolidation complete all as specified and directed by Engineer -in-Charge.

M&L providing cement concrete of type C1, 1:3:6 using 20mm graded stone aggregate in kerbs including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Supply and fixing LED light fitting 2x16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed.

S&F flame proof weather proof DB SPN DB 8 way complete all as specified and directed. Make - MCDB CAT Part No. MCDB - 186 of Sudhir or Equivalent make as per Appx B as approved by GE.

Supply and fix Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete all as specified and directed.

Supply and fix MCB SP 6 to 32 Amps, 10 KA, 'C' series complete all as specified and directed.

Supply and fix MCB SPN 6 to 32 Amps, 10 KA, 'C' series complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm×60cm× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 SSR Part-I 2009 and specified or indicated including excavation and earth work in any type of soil PCC (1:3:6) type C1 in chamber, precast RCC 50mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM (Weight not less than4.00 Kg/Square metre) with PCC frame, funnel with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm mm bore medium grade GI protection pipe, test point etc complete all as specified and directed. NOTE :- The rate of above Item includes the cost of earth lead and GI protection pipe up to 7.5 Metres. Earth wire beyond 7.5 Metre shall be measured and paid for separately.

S&F sub main wiring with 2 Run of 1.5 Sqmm cable multistranded FRLS copper conductors 1100 volt grade IS- 694 marked drawn through and including in steel conduit pipe medium grade ISI marked (not less than 20 mm dia) along with fittings and accessories all fixed on wall and surface on ceiling and including one run of 1.5 sqmm cable for as earth continuity conductor complete all as specified and directed. (Note :- 2 runs of main cable one run of earth wire and one run of steel pipe shalll be measured and paid as one unit).

Supply, Laying, Testing and Commissioning of LT cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables cross sectional area 10 Sqmm 4.0 core (Heavy Duty) 1100 Volts, grade with stranded Aluminium conductor laid in trenches/wall complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches in soft/loose soil not exceeding 1.5 m deep and not exceeding 1.5 mtr wide and getting out including forming bottom surface to required levels/gradients/slopes for foundations/laying of cable complete all as specified and directed. Note :- Excavation shall be carried out manually all as directed.

Removal of surplus excavated soil to a distance not exceeding 50 Mtr distance and depositing as directed at a level not exceeding 1.5 mtr above starting point complete all as specified and directed.

Material & labour for tibba sand cushioning for XLPE cable with tibba sand (one layer of 80 mm thickness before laying of cable and other layer of 150 mm thickness after laying of cable) & punning down to 180 mm to provide a required cover complete all as specified and directed by the Engineer-in-Charge. Note:- Punned thickness only shall be measured and paid.

Material & labour for stone slab 40 mm to 50 mm thick rough dressed Jodhpur stone patties/ slab cover in trenches for protection of cable 25 cm to 30 cm wide and not less than 50 cm in length laid dry abutting each other with gap between adjacent slab not exceeding 10 mm laid over sand cushioning complete all as specified and directed by the Engineer-in-Charge.

suryabuildtechdevlopers

DEV INDUSTRIES

GB Group & Co

Keystone Constructionare

D DEV COMPANY

Om Trading Corporation

VIKAS CONSTRUCTION CO.