PROVISION OF RAIN PROTECTION SHEET AT EXISTING HANGAR FOR DG SET TWO MAIN GATES AT ARMOURY BUILDINGS CUBICLES WORKS AT ACCTS SECTION AND ADDNALTN TO MT REST ROOM AT 17 FBSU 257 SU UNDER GE AF TRIVANDRUM

Amount

SCHEDULE 'A'

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry built in cement mortar or cement lime mortar complete all as specified and directed.

Taking down chowkats or frames of any description exc 1.5 Sqm but not exc 4 Sqm each with shutters complete all as specified and directed.

M & L for powder coated Aluminum anodised frame not less than 50 micron for partition, doors, sliding windows, and ventilators aluminium section inlcuidng necessary jointing cleats, glazing clips, ruber neoprene pacing, , anodised alumium snap beading screws etc. complete all as specified and directed.

S & F powder coated aluminium door shutters not less than 50 micron , aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 nos in each door, hinges anodised aluminum snap beading screws etc complete all as specified and directed.

S & F Anodised aluminium powder coated window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings complete all as specified and directed.

M & L for 12 mm thick prelaminated particle board, exterior grade,prelaminted both side with decorative choice lamination, fixed with screws to aluminium frame work etc complete all as specified and directed.

S & F 5 mm thick sheet glass ordinary quality in square or rectangle exc 0.5 sq. m in each pane fixed to aluminium window frame including necessary jointing cleats, glazing clips,ruber neoprene packing, anodised aluminium snap beading, screws complete all as specified and directed.

S & F in repairs aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium wire staples complete all as specified and directed.

M & L for providing aluminium anodised powder coated decorative grill fixed with aluminium windows including frame fixed in any position complete all as specified and directed.

S & F of double action floor spring hydraulically regulated, made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty suitable for aluminium doors openable in two directions complete all as specified and directed.

S & F 150 mm long aluminium, anodised, barrel tower bolts of extruded section, complete all as specified and directed.

S & F butt hinges, of size 125 mm, type B-21, extruded brass with galvanised mild steel hinge pin, bright polished and fixed complete all as specified and directed.

S & F aluminium alloy anodised sliding door bolt with hasp and staple (bolt type), 250 mm long, and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast alluminum alloy complete all as specified and directed.

S & F mild brass 4 lever mortice lock, vertical type 100 mm size complete all as specified and directed.

S & F floor door stopper of aluminum alloy body and tongue,over all length of cover plate 150mm anodised with hard drawn steel spring, overall length suitable for aluminium door/ woodden door complete all as specified and directed.

S & F of door closer, aluminium body, hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S & F TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for RCC 1:2:4, type B-1 using 12.5 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, etc complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; and thickness not exceeding 200 mm (horizontal or sloping) for flat rough finished surface of concrete complete all as specified and directed.

S & F of aluminium powder coated 20 mm dia curtain rods chromium plated fixed with brackets including taking down of old curtain rods complete all as specified and directed.

M & L for preparing old plastered surfaces of walls and applying two coats of oil bound distemper over one coat of chalk whitening complete all as specified and directed.

Taking down cement plaster including raking out joints, hacking for keys, scrubbing down with water complete all as specified and directed.

M & L for rendering 15 mm thick on other than fair faces of brick or concrete surfaces in CM 1:4 finished fair and even and smooth without using extra cement complete all as specified and directed.

M & L for brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M & L for granite (of any type) work using 20 mm thick granite (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and the like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M & L for 18/19 mm thick Prelaminatd particle board,exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work,necessary jointing cleat & rubber beading etc complete all as specified and directed.

M & L for 5.5 mm thick sheet glass, ordinary quality and glazing with rubber beading exceeding 0.5 sqm in each panecomplete all as specified and directed.

S & F mild steel rolled sections as in framing for cladding, glazing and main and cross beam, hip and jack rafters, purlins where connected to main rafters fixed with angle cleats or other connecting plates confirming to Fe 410-W (Gde E-250) Quality 'A' complete all as specified and directed.

S & F mortice locks for cupboard, grade 1, size 50 mm, brass, 2 lever complete all as specified and directed.

M&L Long fancy type 100mm brass handles, fabricated type polished complete all as specified and directed

M & L for preparation of new steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide Zinc Chrome primer complete all as specified and directed.

S & F of MS angles as struts in fencing and tie bars including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing GI sheets etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 drilled and screwing etc. complete all as specified and directed by Engineer-in-Charge.

S & F pre-painted galvalume aluminium zinc coating GI based plainsteel sheet of 0.50 mm thickness and approved colour having tensile strength of 550 Mpa as in roof covering/cladding to wall ridges fixed with self taping screws complete all as specified and directed.

Supply only Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, 11 to 15mm dia of shank exc 5cm long but n. exc 10 cm long. complete all as specified and directed.

M & L for preparation of new steel /iron surfaces of any description and applying two coats of epoxypaint over a coat of epoxy primer complete all as specified and directed.

Excavation in trenches n.exc 1.5 m in width and n.exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, ramming etc in layers n.exc 25 cum including levelling, watering etc complete all as specified and directed.

Removing excavated materials to a distance not exc 50 m and depositing where directed at level n. exc 1.5 m above from the starting point complete all as specified and directed.

M & L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete for retaining wall complete all as specified and directed.

S & F TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces of concrete complete all as specified and directed.

M & L for formwork to sides of pillars, posts, struts, piers, columns, and stanchions for rough finished surfaces of concrete complete all as specified and directed.

M & L for Reinforced cement concrete Nominal mix 1:2:4 (using 20 mm graded aggregates) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M & L for Reinforced cement concrete Nominal mix 1:2:4 (using 20 mm graded aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M & L for rendering 10 mm thick in cement mortar 1:4 even and smooth with out using extra cement complete all as specified and directed.

M & L for preparation of newly plastered surfaces of walls and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed.

S & F mild steel plain, black sheets 1.60 mm thick in wall cladding steel gates and similar work cut to size,holes punched; including round headed screws, clout nails or rivets fixed to wood or steel framing with plain 40 mm lap joint with riveted or welded seams including bending or turning up mitered angle as required complete all as specified and directed.

S & F mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, and similar work confirming to Fe 290 (E-165 grade) complete all as specified and directed.

S & F mild steel bands, straps, hook and pintle hinges;: large hasps and staples; chains; clamps; hold fasts; wall ties; plain angle cleats for securing purlins to wood trusses or rafters; and similar small articles conforming to Fe 410-O 0r Fe 310-O complete all as specified and directed.

M & L for preparing surfaces of mild steel materials, new or old of any description & girth not otherwise described & treating ends of posts, back of chowkhats etc area tarred exc 0.1 Sqm but n.exc 0.5 Sqm complete all as specified and directed.

Sub Total of Schedule 'A'

SCHEDULE OF CREDIT

Schedule of Credit (Minus) Rs. 1550.00 B/F from Ser page No.109 NOTE: Bidder shall insert credit amount as rate Rs. 1550.00 in Green field under Col-5.

Sub Total of Schedule of Credit

DEFT GROUP ELECTROMECHANICAL