Construction of Rest House at Dharampur Dist Valsad

No figures

1 Excavation for foundation Upto 1.50 m depth including 1293.00 Cum 117.08

sorting out and stacking of the useful materials and

disposing off the excavated stuff up to All lead. (A) loose

or soft soil.

2 Excavation for foundation from depth 1.50 m to 3.00 m 516.00 Cum 162.56

including sorting out and stacking of the useful materials

and disposing off the excavated stuff up to all lead. (A)

Dense or Hard soil.

3 Filling available excavated Earth (Excluding Rock) in 900.00 Cum 130.39

trench plinthside of foundation etc. in layer not

exceeding 20 cm in depth consolidation each deposited

layer by ramming and watering etc. complete.

soil in layers of 20 cm Thickness including watering,

ramming and consolidating etc. complete.

5 Filling in plinth with sand in layers of 20 cm. Thickness 83.70 Cum 460.19

including watering ramming and consolidating etc. comp.

with all lead and lift.

6 Anti Termite System: P/L of Permenent piping 528.00 Sqm 134.33

technology Anti Termite treatment before flooring work

by installing LLDP (Low linear density Polyethylene)

tube of 8 mm O.D.& 6.4 mm I.D.With in Built Pressure

Compenstaion chif every 30 cm interval in the tube,

having working pressure of 2 kg/cm 2 and realese rate of

1.9 ltr/Hour fixed by P-Clip and nails . The LLDP pipe

shall be installed at the entire periphery of the building

and at internal network of building depth of 20 to

mm under floor every 2 to 3 mtr.c/c distance (adjustble

as per building layout ) & Ends of loop pass through a

PVC Elbow of minmum 32 mm ID at junction box of wall

and floor level, entring into a steel reinforcmed grooved

flexible pipe mini.22 mm LD leading into junction box

and during injecting chemicls for termite control

tretment. The anti-termite chemical Lmidcloprid 30.5%

SC Mix as per IS 6313(part-III) shall be injected by the

pressure pump diluted with water @ 10.5 ml/5ltr of

water at the rate of 2 kg/sq,cm.@ 5 ltr /Smt .the

contractor shall submit approved line plan for piping

system and junction boxes dully approved By Engineer -

in-charge with bond of 5 Years warnty .

Item Rate In

Description of Item Quantity Unit Amount

No figures

7 Providing and laying controlled cement concrete M.150 299.80 Cum 4581.29

for curing complete including cost of formwork and

reinforcement for reinforced concrete work in (A)

Foundations, footings,Base of columns and Mass concrete

8 Providing and laying cement concrete 1:3:6 (1-Cement : 80.00 Cum 3005.76

3- coarse sand : 6- hand broken stone aggregates

mmnominal size) and curing complete excluding cost of

formwork in (A) Foundation and Plinth

9 Providing and laying controlled cement concrete M-200 91.20 Cum 4760.53

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in plinth Slab

10 Providing and laying controlled cement concrete M-250 351.00 Cum 5125.55

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Footing and Mass concrete

11 Providing and laying controlled cement concrete M-250 33.00 Cum 7396.74

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in (d) columns Up to Ground Level

12 Providing and laying controlled cement concrete M-200 67.00 Cum 7335.28

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Columns, pillars posts and struts For

13 Providing and laying controlled cement concrete M-250 130.20 Cum 5803.26

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Plinth & Ground BEAMS

14 Providing and laying controlled cement concrete M-200 82.80 Cum 6022.63

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in beam for All floor

15 Providing and laying controlled cement concrete M.200 16.30 Cum 6905.52

and curing complete excluding the cost of formwork and

reinforcement for reinforced concrete work in (B) Walls,

from top of foundation level upto floor two level For All

16 Providing and laying controlled cement concrete M-200 84.40 Cum 6166.91

and curing complete including the cost of form work but

excluding the cost of reinforcement for reinforced

concrete work in Slab for All floor

17 Providing and laying controlled cement concrete M-200 3.50 Cum 7497.43

and curing etc. complete including the cost of form work

and reinforcement for reinforced concrete work in (c)

Lintel for All floor

Item Rate In

Description of Item Quantity Unit Amount

No figures

18 Providing and laying controlled cement concrete M-200 7.50 Cum 6237.36

and curing etc. complete including the cost of form work

and reinforcement for reinforced concrete work in (c)

Chhajja for All . floor

19 Providing and laying controlled cement concrete M-200 22.00 Cum 6100.20

for RCC work and curing complete including the cost of

form work but excluding the cost of reinforced concrete

work in coping on All Floor

20 Providing and laying controlled cement concrete M-200 6.30 Cum 7059.65

and curing etc. complete including the cost of form work

and excluding the cost of reinforcement etc. complete in

(E) Stair case up to floor two level for All floor

21 Providing TMT Bar FE 550D reinforcement for R.C.C. 90728.00 Kg 94.99

work including bending, binding and placing in position

complete upto floor two level

22 Providing cement vata (10cm. x 10 cm. size) quarter 70.90 Rmt 23.68

round in cement mortar 1:1 including neat cement

finishing, watering etc. complete.

23 Brick work using common burnt clay conventional 64.00 Cum 4021.02

building bricks having crushing strength not less than

Kg/Sqm. in Foundation and Plinth in cement mortar 1:6 (

1 cement : 6 fine sand ) including curing etc. complete.

24 Brick work using common burnt clay conventional 354.40 cum 4296.04

building bricks having crushing strength not less than

Kg/sqcm. in Super structure for All floors in cement

mortar 1:6 ( 1 cement : 6 fine sand ) including curing etc.

25 Half brick masonary in common burnt clay conventional 133.00 Sqm 653.07

building bricks having crushing strength not less than

Kg/Sq.cm. in C.M. 1:4 ( 1 cement : 4 coarse sand )

including curing etc. complete for all floors.

26 Providing 10 mm thick Mala cement plaster with 1x1 cm 617.00 Sqm 149.08

grooves in single coat on brick/concrete wall/ceiling for

interior plastering upto floor two level finished even and

smooth including scaffolding, curing etc. complete. In

Cement mortar 1:3(1 cement : 3 fine sand) for all floors.

27 Providing 20 mm thick double coat mala cement plaster 2351.00 Sqm 272.50

on interior brick / concrete work for plastering

comprising of base coat of 12 mm thick cement plaster in

cement mortar (1 Cement : 4 coarse sand) in rough

finishing and 8 mm thick top coat of cement mortar 1:2

(1 Cement : 2 Coarse sand) finished with trovel including

scaffolding curing etc. complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

28 Applying two coats of putty & two coats of primer of 2570.00 Sqm 40.59

approved brand and manufacture on new wall surface to

give an even shade including thoroughly brushing the

surface free from mortar dropping and other foreign

matter and sand papered smooth.

29 Finishing wall with 100% acrylic emulsion wetherproof 2469.00 Sqm 114.53

paint on wall surface to give an required shape even

shade after thoroughly brushing the surface to remove all

dirt, and remains of loose powdered materials.etc

complete for any height as directed by Architect.

30 Wall painting (two coats) with plastic emulsion paint of 1953.00 Sqm 80.35

approved brand and manufacture on undecorated wall

surface to give an even shade including throughly

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

31 Wall painting (two coats) with plastic emulsion paint of 617.00 Sqm 85.76

approved brand and manufacture on undecorated Ceiling

surface to give an even shade including throughly

brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

32 20mm thick sand faced Gutka cement plaster on walls 2473.00 Sqm 300.66

upto height 10 metres above ground level consisting of

12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand)

and 8mm thick finishing coatof C.M. 1:1 (1-cement : 1-

sand) etc. complete.

33 P & L 60x60/80x80 cm' Double charged vitrified 8 mm 205.00 Sqm 1511.97

thick tile flooring over 20 mm (average)base of cement

mortar 1:6 (1cement : 6 coarse sand) on new surface or

fixing on existing flooring by adhesive materials

including dismentalig of existing flooring and jointed

with colour cement slurry including groving of perifery

of tiles with required diammention & finished with flush

pointing and cleaning the surface etc. complete

34 P & L 60x60/80x80 cm Double charged vitrified 8 mm 14.00 Sqm 1326.13

thick tile in risers of steps,skirting Dedo and pillars laid

on 10mm thick cement mortar 1:3 (1-Cement : 3 coarse

sand) and jointed with colour cement slury mixed with

pigment to match the shade including groving of perifery

of tiles with required diamention & finished with flush

pointing and cleaning the surfaceetc. complete

Item Rate In

Description of Item Quantity Unit Amount

No figures

35 P & L 60x60 cm' Matt Finnihed GVT vitrified with 10 mm 152.00 Sqm 1546.31

thick tile flooring over 20 mm (average)base of cement

mortar 1:6 (1cement : 6 coarse sand) on new surface or

fixing on existing flooring by adhesive materials

including dismentalig of existing flooring and jointed

with colour cement slurry including groving of perifery

of tiles with required diammention & finished with flush

pointing and cleaning the surface etc. complete

36 P & L 60x60 cm Matt Finnihed GVT charged vitrified 8 11.00 Sqm 1361.48

mm thick tile in risers of steps,skirting Dedo and pillars

laid on 10mm thick cement mortar 1:3 (1-Cement :

coarse sand) and jointed with colour cement slury mixed

with pigment to match the shade including groving of

perifery of tiles with required diamention & finished

with flush pointing and cleaning the surface etc. complete

37 P & L 60x45 cm Machine cut,Machine polished Blue Kota 47.00 Sqm 1029.22

Stone slab 30 mm thick flooring over 20 mm

(average)thick base of cement mortar 1:6 (1-cement 6-

coarse sand) or L.M 1:1.5 (1 Lime putty : 1.5 coarse sand

laid over and jointed with grey cement slurry mixed with

pigment to match the shade of slab including rubbing and

polishing etc.complete

38 P & L Machin cut Machin polished Blue Kota Stone 25 1.00 Sqm 1089.67

mm thick in riser of steps,skirting dedo and pillars laid

on 10 mm thick cement mortar 1:3 (1-cement 3-coarse

sand) and jointed with grey cement slurry mixed with

pigment to match the shade of slab including rubbing and

polishing etc.complete

39 Providing and laying 600 mm x 600 mm Antiskid 139.00 Sqm 970.07

Ceramic tiles in flooring, treads of steps & landing on a

bed of 12 mm thick cement mortar 1:3 (1 cement :

coarse sand) finished with flush pointing in white cement

and aproved colour, shade and size by Architect or

Engineer in charge for all floors.

40 Providing and laying coloured glazed tiles of the size 600 153.00 Sqm 1582.62

with Boarder Tiles in skirting, risers of steps and dedo on

10 mm. thick cement plaster 1:3 (1 cement : 3 coarse

sand) & jointed with white cement slurry.

Item Rate In

Description of Item Quantity Unit Amount

No figures

41 Providing and laying machine cut free edge machine 100.00 Sqm 2839.11

mirror polished granite stone 18mm thick finished

treads and risers in length with 1cm projecting, nozing

rounded moulding in tread laid over 12 mm (av.) thick

bases of cement mortar 1:6 (1-cement : 6-coarse sand)

jointed with grey or colour cement slurry including

rubbing and polishing incl. making Three No.s of grooves

of size 3mm X 3mm along the length of treads etc.

42 Providing and laying 18 mm thick polished Black Granite 95.00 Sqm 1949.30

in single piece with all exposed edges polished,

chamfered and proected 6mm from finished wall

thickness in sill and jambs laid on 10 mm thick cement

mortar 1 : 3 ( 1 cement : 3 coarse sand ) laid over and

jointed withgrey cement slurry including rubbing and

polishing etc. complete. also Fixing: Rear face of granite

shall be standed using clean sand sieve no. 10 passed

2mm fixed with araldite and dried for at list 36 hours.

43 Providing, fixing and construction of sandwich type 18 9.00 Sqm 6715.49

mm thick One Side polished Granite Stone of uniform size

and colour for kitchen/pantry/countr/ laboratory

shelves etc. in floor, dedo or facia upto 100 mm wide

including necessary cement mortar bedding in cement

mortar 1:2 of required thickness. Granite Stone shall be

fixed over 25 mm thick Polished Kota bottom, cement

joints and pointing as specified with necessary making of

edges, polishing curing daily mopping with water and

kerosene as directed for atleast 15 days or upto the

satisfaction of engineer-in-charge.

44 Providing and fixing Kitchen sink with C.I. or M.S. 2.00 Nos 9689.94

brackets, painted white including cutting holes in walls

and making good the same but excluding fittings. ©

Vitreous China Sink.(i) 400x550 size

45 Providing and laying 25 mm thick double polished Kota 8.00 Sqm 520.66

stone Shelves in single piece including fixinng in position

in cement mortar 1:3 (1 cement : 3 coarse sand) and

joined with grey cement slurrly including moulding

machine cut open edge as dircted by Engineer in charge

etc complete as per detailed drawing and as Instructed

by Engineer In charge.

Item Rate In

Description of Item Quantity Unit Amount

No figures

46 Providing and laying China mosaic type water proofing 579.22 Sqm 1149.38

treatment on terrace including cleaning the surface by

wire brush as directed including applying neat cement

slurry @ 2.75 Kg/Sq.smt. mixed with water proofing

compound after cleaning the surface, laying cement

concrete using brickbats 25 to 100mm size well

immersed in water with 50% of cement mortar 1:5 (1

cement :5 coarse sabd) mixed with water proofing

compound over 20mm thick layers of cement mortar 1:5

(1 cement :5 sand) to required slope including rounding

of junctions of walls and slabs and after two days of

proper curing, applying second coat of cement slurry

finishing the surface with rate 20mm thick cement

mortar 1:4 and china mosaic tiles and finally finishing the

surface with white cement slurry and after finishing the

whole terrace shall be flooded with water for a period of

two weeks.

47 Providing and fixing a 35mm thick flush double door 4.00 Sqm 4966.68

shutter, solid core, conforming to IS:12823 and from an

ISI-approved manufacturer, with 6mm thick teakwood

beading on the periphery for durable hinge grip (4

hinges per shutter). The double shutters are finished

with 1mm thick laminate on both sides and a resin layer

for added durability. The doors are equipped with 15cm

long stainless steel handles on both sides, a locking

system, and all necessary fixtures and fastenings, as

directed by the Engineer-in-Charge, ensuring complete

functionality and aesthetics.

48 Providing and fixing a 35mm thick flush Single door 41.00 Sqm 5597.62

shutter, solid core, conforming to IS:12823 and from an

ISI-approved manufacturer, with 6mm thick teakwood

beading on the periphery for durable hinge grip (4

hinges per shutter). The double shutters are finished

with 1mm thick laminate on both sides and a resin layer

for added durability. The doors are equipped with 15cm

long stainless steel handles on both sides, a locking

system, and all necessary fixtures and fastenings, as

directed by the Engineer-in-Charge, ensuring complete

functionality and aesthetics.

49 Providing and fixing fully glazed entrance door using 12 18.00 Sqm 4518.30

mm thick toughened glass including polished edges, all

necessary patch fittings (top & bottom), stainless steel

pull handles (300mm), floor spring (double action),

including cutting, edge polishing, rounding of corners,

fittings with accessories like locks,, etc., complete in all

respects as per design and direction of Engineer-in-

Item Rate In

Description of Item Quantity Unit Amount

No figures

50 Providing and fixing standared extruded of alluminium 2.00 Sqm 1833.29

section of size 63.50 x 38.10 x 1.95 mm,@ Wt 1.094Kg /

Rmt with colour Powder Coated alluminium frame with

mm thick transparent bronze colour tinted float glass as

details etc complete for Fix window.

51 Providing and fixing three track Sliding window (2 27.00 Sqm 4043.82

shutter + 1 mosquito shutter) with standard extruded

colour anodized aluminum section equivalent to series E

(30 mm) section numbers are : shutter top & bottom-

20993, shutter inter lock - 20550, shutter side (handle) -

20549, frame-bottom with gutter (Weep Holes)-

frame top & side – 20837 with 5 mm thick transparent

tinted float glass with sun control film in pattern as

directed,fixing Wire Mosquito Mesh Jali of 0.71mm

Gauge with All required Fittings as per window size with

rubber gasket, air lock strip and finishing joints with

silicon sealant, with standard extruded colour anodized

aluminum coated fittings as per details etc complete.

52 Providing and fixing three track Sliding window (3 7.00 Sqm 4079.71

shutter) with standard extruded colour anodized

aluminum section equivalent to series E (30 mm) section

numbers are : shutter top & bottom- 20993, shutter inter

lock - 20550, shutter side (handle) - 20549, frame-

bottom with gutter (Weep Holes)- 20928, frame top &

side – 20837 with 5 mm thick transparent tinted float

glass with sun control film in pattern as directed,fixing

Wire Mosquito Mesh Jali of 0.71mm Gauge with All

required Fittings as per window size with rubber gasket,

air lock strip and finishing joints with silicon sealant,

with standard extruded colour anodized aluminum

coated fittings as per details etc complete.

53 Providing and fixing in position standard extruded, 6.00 Sqm 1657.41

approved color anodized aluminum ventilator with an

outer frame of 65.00 x 25.00 x 1.95 mm @ Wt

kg/Rmt), fitted with 3mm thick Bajari figure adjustable

tinted glass louvers. The ventilator includes provisions

for an exhaust fan opening and is complete with all

fixtures, fastenings, labor, and equipment as per detailed

drawings and as directed by the Engineer-in-Charge.

54 Providing & fixing M.S. grills of required pattern to 714.00 Kg 104.04

wooden frames of windows etc. with M.S. flats at

required spacing & frame around, square or round bars

with round headed bolts & nuts or by screws(A)Plain

Item Rate In

Description of Item Quantity Unit Amount

No figures

55 Painting three coats (one coat of priming coat + two coats 41.00 Sqm 122.49

of enamel paint) on new steel and other metal surface

with enamel paint, brushing interior to give an even

shade including cleaning the surface of all dirt, dust and

other foreign matter.

56 Providing & Fixing 114 mm wide M.S . Sheets louvers 21.00 Sqm 4781.04

having weight not less than 490 Gm/m roll formed to

create 84mm wide louver snap fixed on special shaped

MS channel. Fix louvers & channels shall finished with

powder coating of 55 micron (1) 0.55mm thick sheet.etc.

complet as per detail drawing as directed.

57 Providing and Fixing S.S Hand Rail made SS 316 of 50 30.00 Rmt 1583.18

mm inside dia 16 guage round pipe supported with 8 mm

thick SS 316 base flange on wall including end S.S ball

75mm dia, anchor fasteners, nuts, accessories as per

detailed drawing etc. complete as directed by Architect

or Engineer in charge.

58 Providing and Fixing S.S. Railing for staircase made from 32.00 Rmt 2813.46

S.S 316 Grade 1.8 mm wall thickness matt finish, 50 mm

Top hand rail, 38 mm Vertical Balustrade fixing at 1.2 mt

C/C with anchor fastner 75 mm dia 8 mm thick flange

and shoe cap, with 3 No of 16 mm Horizontal pipe fotting

with L and Key , modular knob system. Balustrade top

modular "T" fixing support to 50 mm hand rail and

turning fixed with modular bend. including accessories

as per detailed drawing as directed etc. complete.

59 Providing and fixing Wall Hung CERA or equivalent 6.00 No 17814.38

CARLTON Cat.No.S1044147 snow white size

490x350x360mm P Trap with Duroplast slim soft close

seat cover including Health Faucet ABC body with 1 m SS

Braided connection pipe, Flush cock Consisting of

exposed part F1013751 (Lever, Cartridge, sleeve, flange)

and Concealed part F4060102 with all fitting inlet and

outlet connection and all required fitting accessories etc.

completed as per directed engineer in-charge.

60 Providing and fixing Wash Basin CERA or equivalent 7.00 No 5908.50

CHERUB Cat. No. S2020112 Snow White size

400x400x135mm including Polyamide braided

connection pipe 12mm dia, 450mm length Cat. No.

F8070402, Wast coupling with ceramic Pop-up push type

(Full thread) 32mm Dia Cat. No. F8050351 with all fitting

inlet and outlet connection and all required fitting

accessories etc. completed as per directed engineer in-

Item Rate In

Description of Item Quantity Unit Amount

No figures

61 Providing and fixing Swivel Mirror 630 X 445mm 7.00 No 3229.98

Rectangular Shape including all Fittings and labour

charges etc. Completed as per directed engineer in

62 Providing and fixing Single Towel Rail 300mm Long 13.00 No 2590.65

(AQN-GRF-7711B) including all Fittings and labour

charges etc. Completed as per directed engineer in

63 Providing and fixing Overhead Shower 120mm Round 6.00 No 3810.73

Shape Multi Flow with Cascade Effect (ABS Body Chrome

Plated with Gray Face Plate) with Rubit Cleaning System

including all Fittings and labour charges etc. Completed

as per directed engineer in charge.

64 Providing and fixing CERA Bib cock with Wall Flange and 15.00 No 2657.31

aerator Cat.No. F1016151 with 15mm dia extension

nipple including all Fittings and labour charges etc.

Completed as per directed engineer in charge.

65 Providing and fixing CERA Pillar cock with 310mm long 8.00 No 2904.76

extended body and aerator Cat.No. F1016102 including

all Fittings and labour charges etc. Completed as per

directed engineer in charge.

66 Providing and fixing WALL MIXER ( 3-IN 1) Cat. 6.00 No 5616.61

No.F1019403 Chrome Plating including all Fittings and

labour charges etc. Completed as per directed engineer in

67 Providing and fixing CERA Angle cock with wall flange 9.00 No 2045.25

Cat.No.F1016201 including all Fittings and labour

charges etc. Completed as per directed engineer in

68 Providing and fixing Soap Holder including necessary S.S. 9.00 No 677.71

screw with labour etc. complete.

69 Providing laying and jointing in true line and level 50mm 60.00 Rmt 195.67

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

70 Providing laying and jointing in true line and level 40mm 50.00 Rmt 148.12

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

Item Rate In

Description of Item Quantity Unit Amount

No figures

71 Providing laying and jointing in true line and level 25mm 200.00 Rmt 91.84

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

72 Providing laying and jointing in true line and level 15mm 180.00 Rmt 72.65

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings as approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

73 Providing laying and jointing in true line and level 110 69.00 Rmt 836.73

dia. U.P.V.C. (Type 'B') with one end plain and other end

socketed with rubber ring , pipe and fittings conforming

to IS 13592 as approved by Engineer In Charge. pipe

shall be fixed on the wall with the help of PVC clamp at

every two metre C/C or shall be concelled as directed

including necessary fittings such as shu bends, tee, shoes

etc. including testing of pipe and joints and fixing the

same with PVC Clamp with adhesive solvent cement

including cost of all material.

74 Providing, laying and jointing in true line and level 75 60.00 Rmt 777.70

mm dia. UPVC SWR Type B pipe conforming to IS 13592-

1992 with one end plain and other end socketed with

rubbering and fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe

shall be fixed on wall using of PVC clamp at every

mm c/c or shall be conceled in walss as directed

including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with

adhesive solvent cement including cost of all materials.

75 Providing, laying (to level or slopes) and jointing 203.00 Rmt 665.48

reinforced concrete Light duty non-pressure pipes I.S.

class NP2 of the following internal diameter with collars

and butt ends prepared for collar joints including testing

of joints complete. (i) 300mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

76 Providing laying and jointing in true line and level 160 50.00 Rmt 831.22

dia. U.P.V.C. (Type 'B') with one end plain and other end

socketed with rubber ring , pipe and fittings conforming

to IS 13592 as approved by Engineer In Charge. pipe

shall be fixed on the wall with the help of PVC clamp at

every two metre C/C or shall be concelled as directed

including necessary fittings such as shu bends, tee, shoes

etc. including testing of pipe and joints and fixing the

same with PVC Clamp with adhesive solvent cement

including cost of all material.

77 Providing and fixing in PVC SWR cowel went 75mm dia 6.00 Nos. 15.15

to pipes.(B) 75mm dia.

78 Providing and fixing in PVC SWR cowel went 110mm dia 14.00 Nos 27.27

to pipes.(B) 110mm dia.

79 Providing and fixing PVC SWR Nahni trap IS 14735 for 13.00 No 571.08

drain - 100 mm diameter with jali of the following

nominal diameter of self cleansing design with C.I scread

down or hinged grating including the cost of cutting and

making good the walls.

80 Providing and fixing S.W. gully trap with C.I. grating brick 13.00 No 1246.92

masonry chamber and water tight C.I. cover with frame

of 300mm x 300mm size (inside) with standard

weight.(i) Square mouth traps.(B) 150mm x 100mm size

P or R type

81 Constructing brick masonry chamber for underground 25.00 No 3895.37

Inspection chamber and bends with bricks having

crushing strength not less than 35Kg/Cm2 in C.M. 1:5

precast fibre reinforced concrete frame & cover 455mm

x 610mm intenal dimensions R.C.C. top slabe with 1:2:4

mix (1-cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc. complete.(ii) Inside dimensions 500mmx

700 mm and 450mm deep for pipe line with one or two

82 Extra over for every additional depth of 0.10m or part 17.00 No 264.86

thereof beyond 0.45 m depth for brick masonry chamber.

(II) For 500 mm x 700 mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

83 Constructing brick masonry chamber for underground 14.00 No 7281.02

Inspection chamber and bends with briocks having

croshing strength not less than 35Kg. Cm2 in C.M. 1:5

precast fibre reinforced concrete frame & cover 455mm

x 610mm intenal dimensions, (R.C.C. top slabe with 1:2:4

mix (1-cement :2- coarse sand :4-graded stone aggregate

20mm size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed

concrete etc. complete.(iii) Inside dimensions 600mm x

850 mm and 450mm deep for pipe lines with three or

more inlets.

84 Extra over items 24.44 for every additional depth of 6.00 No 325.59

0.1M. Of part thereof beyond 450mm depth for Brick

masonry chamber.(iii) for 600mm x 850mm size.

85 Providing erecting and fixing double coated ISI water 5000.00 Litre 3.95

tank of required capacity each with all necessary fittings

and connection etc. complete on terrace

86 Providing and fixing 50 mm dia copper metal ball cock of 1.00 No 189.84

approved quality as directed.

87 Providing, filling and laying Cinder in sunken area 13.00 Cum 438.14

including ramming, watering, consolidating for all floors

etc complete as directed by Engineer in charge.

88 Providing and laying water proofing treatment by 72.00 Sqmt 978.69

conventional method including cleaning the slab surface

by wire brush as directed including provding first layer

of C.M. 1:4 of 40 mm thickness mixed with water

proofing compound at rate prescribed by manufacturer,

including putting of brick bats of average thickness

mm Well immerssed in water laid uniformly on first

layer of mortar including applying cement slurry @ rate

of 0.08 bag/sqm. on fixed layer of brick bats including

maintaining necessary slope, in second layer 40 mm

thick C.M 1:4 mixed with water proofing compound as

directed, including finishing smooth with cement slurry

as directed complete.

89 Providing and fixing in position 300 mm high, English 50.00 Nos 707.00

letters made from 1.0 mm thick stainless steel sheet as

directed by Engineer in charge with all necessary tools &

plants etc. complete.

90 Providing and fixing in position 150 mm high, English 50.00 Nos 404.00

letters made from 1.0 mm thick stainless steel sheet as

directed by Engineer in charge with all necessary tools &

plants etc. complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

91 Design, supply & installation of Signages including 17.00 Sqm 5596.41

normal lettering with additional raised tactile and

graphical symbols, height 15 mm to 55 mm Brailled text

and Braille locator made of zink sulphide based glow in

the dark rigid sheet with high luminous property

enclosed in a transperent weather proof U/V stabilised

plastic pasted on 3 mm thick clear acrylic sheet sheet.

92 Providing and fixing MS ladder of required pattern with 250.00 Kg 113.12

MS flats (30 X 3 mm) or round or square bars (12 mm) at

required spacing and with round headed bolts and nuts

or screws or welding including primer coat of approved

quality and two coats of oil paints as directed by engineer

in charge.

93 Providing and Fixing 15 mm thick 300 mm x 300 mm 66.00 Sqm 1121.71

Tactile Warning Tiles (Attention Tiles i.e. Tactile Warning

Surface Indicator {TWSI}) of Johnsan Endura Tac Button

Yellow Plus or equvqlent make in flooring laid on 20 mm

thick cement mortar 1:6 (1 cement : 6 coarse sand) on

new surface and jointed with cement slurry including

finished with flush pointing & cleaning the surface for all

floors as per detailed drawing etc. complete as directed

by Architect or Engineer in charge. Thse tiles shall be

Anti Skid, Chemical Resistant, Fade Proof, Frost - Heat &

Weather Proof, High Flexural Strength, Highly Durable,

Stain Resistance . All Tactile Warning Tiles meet the

specific size and dimension standards as required by

ISO/FDIS

94 Providing and Fixing a set of wall mounted horizontal 2.00 set 3110.80

stainless steel collapsible grab bar and vertical stainless

steel fixed grab rail of grade SS 304 from round pipe

supported with 75 mm dia 8 mm thick SS 304 base flange

on wall including anchor fasteners, nuts, accessories as

per detailed drawing etc. complete as directed by

Architect or Engineer in charge.

95 Providing and fixing chicken mesh jali with square of 25 205.00 Sqm 218.16

gauge at junction the masonary and RCC member

including necessary scafolding, labour etc.complete for

all floors.

Item Rate In

Description of Item Quantity Unit Amount

No figures

96 Providing and fixing acrylic multilingual Braille (raised 0.45 Sqmt 16797.91

dots) DIRECTIONAL SIGNBOARDS of size 225 x 150mm

designed as per accessibility standards and having

3.5mm thick acrylic base plate with Upper Case San Serif

words made of white acrylic non glare cut out letters of

height 15mm raised not less than 0.8mm above base

plate and the equivalent word written in Hindi with

Devanagari non glare acrylic letters of height 15mm

raised not less than 0.8mm above base plate and having a

non-glare acrylic cut arrow pointing in the required

direction. Each signboard to be fixed as per

manufacturers specifications on the wall at the approved

location and at a height of 1200mm from FFL complete

as per design / specifications and guidelines as per the

entire satisfaction of the Engineer-in-charge

97 P & F BRAILE INDICATOR OF SIZE 200 MM X 50 MM 50.00 Rmt 771.74

FOR HANDRAILS OF THE APPROVED DESIGN AND

MAKE HAVE BRAILE DOTS RAISED 0.5 MM ABOVE BASE

PLATE TO BE INSTALLED AT SPECIFIC LOCATIONS AS

PER DIRECTION OF ENGINEER IN CHARGE

98 Providing and fixing of conspectus tape 50mm width on 50.00 Rmt 115.14

of treads in staircase including cutting pasting etc. As per

harmonised guidelines complete in all respect to the

entire satisfaction of engineer in charge.

99 Providing and laying Plinth protection 0.40m depth and 153.00 Sqm 2054.34

1.5m wide having 0.2m morrum +0.2m gravel filling

including watering, ramming and consolidating etc.with

bounded buy 0.23m thick brick work (1 sand :6

Aggregate). The top layer shall be 0.10m thick 1:2:4 PCC

and 0.1m thick M150 Concrete work and above

providing and fixing pre-cast Rubber Dye / steel Dye

inter locking concrete block 60mm thick with grade of

concrete M300 pnumatic compressed / vibrated

mechanically and as per approved design Confiraming to

IS 15658 : 2006 including 35 mm Sand layer for levelling

and filling the joint with sand in proper line and level as

per guidlines of IRC : SP 63-2018 etc. Complete.All work

shall be done as per drawing and Directed Engineer

Item Rate In

Description of Item Quantity Unit Amount

No figures

100 Providing and fixing pre-cast Rubber Dye / steel Dye 972.00 Sqmt 686.90

inter locking concrete block 60mm thick with grade of

concrete M300 pnumatic compressed / vibrated

mechanically and as per approved design Confirming to

IS 15658 : 2006 including 35 mm Sand layer for levelling

and filling the joint with sand in proper line and level as

per guidlines of IRC : SP 63-2018 etc. Complete.

101 Providing throating or plaster drip and moulding to 71.00 Rmt 42.17

R.C.C. Chhajja.

102 Providing and fixing 18 mm thick high-density Cement 24.00 Sqmt 2146.25

Fibre Sheet of approved make and as per relevant IS

standards, including CNC cutting in required shapes,

patterns, perforations, and grooves as per approved

architectural drawings, complete with all necessary

fabrication, edge finishing, sanding, and smoothening to

achieve a uniform and neat appearance; the work

includes fixing the sheets on a suitable

MS/Aluminium/wooden framework (as specified) using

approved fasteners, screws, anchor bolts, and adhesives,

making required cut-outs for services, filling joints with

sealant/putty, proper alignment, leveling, and finishing

of exposed edges, along with all handling, lifting,

scaffolding, wastage, and incidental charges, complete in

all respects as directed by the Engineer-in-Charge,

103 Providing and fixing name plate above the entry gate, 2.00 Sqmt 7575.00

made of 304-grade stainless steel with engraved or

embossed letters, including fixing with stainless steel

screws, bolts, and necessary accessories, complete as per

the direction of the Engineer-in-charge.

104 Providing and fixing concealed center point to wall 60.00 Rmt 166.86

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc.

complete.[A] 15 mm.

105 Providing and fixing concealed center point to wall 60.00 Rmt 249.72

ceiling & floor CPVC (SDR 13.5) PIPE having National

Sanitation Foundation (NSF) seal for potable water of

following dia. nominal bore tube fittings and clamps

including making good the wall, ceiling and floor etc.

complete. [C] 25 mm.

106 Excavation for foundation for depth from 3.0 m to 5.0 m 13.00 Cumt 287.48

including sorting out and stacking of useful materials and

disposing of the excavated stuff upto 50 Meter lead.(C)

Hard Murrum

107 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. 1.00 Nos 958.17

size having weight not less than 35Kg.

Item Rate In

Description of Item Quantity Unit Amount

No figures

108 Providing & erecting open well horizontal mono block 1.00 Nos 57686.15

pump set with cast iron body, complete for three phase

submersible motor having

[H]For 15 H.P,3 phase open well horizontal mono block

pump set suitable for 1600 LPM to 1025 LPM @ 33 to

MTR head suitable for 65/80 mm dia delivery pipe Cat-II

109 Supplying & erecting approvedmake 3 phase motor 2.00 Nos 15331.80

control cubicalpanel (Star-Delta) made from 16G.CRCA

sheet duty painted with epoxy powder painted inside

and outside with hinged doors and locking arrangement,

consisting suitable size of ON-OFF isolator (AC-

3/23duty) main fuses,single phasing preventer cum

water level, Guard(Compe unit), Toggle switch to by pass

Single phase preventercum WLG,indicating lamps forR-Y-

Bphases, over load relay.Automatic water level

controller, Ammeter &Voltmeter each with two way

Crimped,Panel to be erected on angle iron frame grouted

on wall as overload relay,thermal/Electronics star delta

cutoff timer,start-stop push buttons.The isolator

overload relay &cntractors ofL&T,Siemens or Cuttler

Hamer make only.Panel to be erected on angle iron frame

ground on wall (e)S/D upto 7.5 H.P.

110 Providing and fixing rolling shutters of approved make 5.00 Sqmt 3503.41

made of 80 mm wide M.S laths inter-locked together

through heir entire length and jointed together at the

ends by end locks mounted on specially designed pipe

shaft with bracket plates,guide channels and

arrangement for inside and outside locking with push-

pull operation including the cost of hood cover and sprig

etc.complete(A) Shutters having width below 3.5M

111 Steel work, welded in built up sections framed work 10314.00 kg 90.48

including cutting, hoisting, fixing in position and applying

a priming coat of read lead paint & two coat oil paint.

(A)In beams and joists, channels angles Tees, flats, with

connecting plates or angle cleats as in main and cross

beams. Hip and jack rafters, purlins conneted to common

rafters and the like..

Item Rate In

Description of Item Quantity Unit Amount

No figures

112 Providing and fixing of Ridge flashing for roof panel shall 414.00 kg 858.67

be made out of 0.5 mm thick pre coated GI sheet . The

Precoated sheet shall be of minimum 240 mpa steel

grade confirming to IS 14246:1995 and shall have zinc

coating of minimum 120 gsm as per IS:277:1992 , 5-7

microns epoxy primer on both side of the sheet and

polyester top coat 15-18 micron. The PPGI Sheet shall

have plastic protective guard film of minimum

microns to avoid scratches during transportation. The

ridge shall be fixed to the steel members by pop rivet or

self drilling/self stitching fastners @ maximum 450 mm

c/c along length of capping/flashing etc complete .

113 Drilling of min. 250 mm dia. bore hole in all strata 150.00 Rmt 1240.28

including dualover burden strata by combination

DR/DTH rig including lowering 200 mm dia MS ERW

pipes in bore hole and testing etc.all work as per directed

engineer incharge.

114 Supplying slotted PVC pipes of approved quality at site of 150.00 Rmt 555.50

work confirming to IS. 1239/1974 180mm dia.

115 Bore plug having 100 mm height made from M.S. plate 100.00 Nos 1161.62

with 3 holes at equal distance on circumference for nut-

bolts type, locking arrangement with nuts-bolts & lock

nuts of std. Make complete. For 250mm dia

116 Providing PVC insulated flat submersible cable as per 110.00 rmt 180.79

detailed technical specifications of R/C of GWSSB

conforming to IS 694, IEC 60227 / 60228.d)1 R x 3 C x

117 Suppling and installing 3 Phase Borewell 3.0 HP 1.00 Set 37130.63

Submersible Pump Sets Electric motor driven

conforming to I.S. 8034 and motor conforms to IS-9283

working at 3 phase 400/440 volt 50 C/S A.C. supply &

2900 R.P.M. cat

118 Providing and fixing check or non return pully wheel 1.00 Nos 1111.00

valve of 50 mm diameter.

119 Manufacture, supply and delivery of following ISI marked 110.00 rmt 152.51

HDPE pipes (IS:4984/1985 with latest amendment)

having material Grade PE-80 in approximate 100 meter

coil length or as per GWSSB requirement with SS

nipple at both ends having 11 TPI threads as per

specifications, press fitted and bolted having nominal

diameter as under as per detailed technical

specifications.

Item Rate In

Description of Item Quantity Unit Amount

No figures

120 Providing and laying (two level or slopes) and jointing 40.00 Rmt. 518.84

with stiff mixture of Cement Mortar in proportion 1:1,

Salt glazed stone ware pipes of pipes 150mm laying lime

concrete 1:2:4 (1-Lime putty :2-Fine samd : 4-Graded

brick aggregates 40mm nominal size) bedding for

stoneware pipes of following internal diameters with

necessary formwork and curing complete.

121 Providing and fixing decorative entrance gate made out 1175.00 kg 172.71

of cast iron and various mild steel tabular section

combination , the Ornamental entrance gate should be

fixed at compound wall including pattern and die making

, cutting , welding , grinding, fabrication , fixing in

position at compound wall with necessary pedestal,

bearing block and other locking arrangement. The

entrance gate should be painted with two coats of

priming coat of paint, and two coat of oil paint etc

complete. As per detail design and instruction of

architect.

122 Providing and fixing concertina coil fencing with 361.00 Rmt 516.11

punched tape concertina coil 600 mm dia 10 mt openable

length having 50 no rounds per 6 mt length, upto 3mt

height of wall with existing angle iron (50mm x50mm

x5mm )requird shaped As per Directed Engeenier in

charge. placed 2.4mt or 3.00mt apart and with

horizontal R.B.T. reinforced barbed wire(3 mm) , stud

tied with G.I. staples and G.I. clips to retain horizontal,

including necessary bolts or G.I.barbed wire tied to angle

iron, all complete as per direction of Engineer-in-charge,

with reinforced barbed tape (R.B.T.)/Spring core (2.5

mm thick) and weight 43.478 gm/meter at compound

wall for ESR M4/ intakewell.

123 Constructing providing and fabricating cattle guard using 9.00 sqmt 5143.93

channel section frame of size ISMC series 100 mm x

mm (Weight 9.20 kg/Rmt) and ISMC section 100 mm x

75mm (weight 11.50 kg/Rmt) intermediate support for

welding G.I.pipe at 12 Cm C/C of size 50 mm in a frame

made of Channel section size 100 mm x 50 mm all round

including fixing the unit on prepared chamber of

masonary wall using MS hold fast embeded in masonary

wall top as directed by Engineer in charge and as per

drawing and necessary required arrangement etc

124 Box cutting the road surface to proper slope and camber 641.00 Cum. 104.04

for making a base for road work including removing the

excavated stuff and depositing on the road side slope as

directed upto 50Mt.lead.

Item Rate In

Description of Item Quantity Unit Amount

No figures

125 Construction of granular sub-base 150 mm thick by 175.00 Cum. 1057.87

providing coarse graded machine crushed B.T. material

satisfying MOST specification of grading I (B.T. stone

aggregate 53 mm to 26.5 mm 35 %, 26.5 to 4.75 mm -

% and 2.36 mm below - 20 % )including spreading in

uniform layer with motor grader on prepared surface,

mixing by mix in place method with rotavator at OMC

and compacting with vibratory roller to achieve the

desired density etc. complete.

126 Providing and laying wet mix macadam base course 250 116.00 Cum. 1094.84

mm (125 + 125)thick using machine crushed B.T. chips

as per required gradation mixing with required optimum

quantity of water, conveying the mix to site of work,

spreading in to grade and camber with mechanical paver

and consolidation each layer with vibratory roller

including cost of material labour plant and equipment

etc. complete.

127 Compaction and finishing of cement concrete road by 927.00 Sqm 63.63

trimix M.250 process providing extra Labour charges for

the trimix vacume dewatering service process on cement

concrete road sutface by using vacuum dewatering pump

floater surface vibrator including making groves and

rough finish to surface including leveling etc complete.

128 Providing and Laying homoginious Grey cement based 342.00 Rmt 361.64

concrete kerbing of size 30 cm x 30 cm x 10 cm size as

per detailed drawing having grade of concrete M25

grade, including necessary excavation, BBCC 1:5:10

cm as per ddetailed drawing fixing in line and level,

filling joints in CM 1:3 with smooth finished, white

washing three coats etc. complete as directed by

Engineer in charge.

129 Providing and fixing and floor 10.0 Kg. F/Cm2 working 141.00 Rmt 336.24

pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression

type fittings, wall clipsetc. including making good the

wall ceiling and floor.(G)110 mm

130 Providing and fixing and floor 10.0 Kg. F/Cm2 working 80.00 Rmt 696.90

pressure poluthene pipes of the following outside Dia.

Low densidy, complete with special falnge compression

type fittings, wall clipsetc. including making good the

wall ceiling and floor.(G)180 mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

131 Providing junction for rain water juncton chamber of size 1.00 Nos. 8603.18

0.60x0.60x0.75m with excavation of size 1.96x1.96 m &

0.15m thick c.c.1:2:4 bed concrete including brick

masonary wall in CM 1:6 of 0.75m height & 0.23m thick

with 15mm thick cement plaster inside & outside &

1.06x1.06 RCC (1:2:4) slab of thickness 0.15m with CRS

steel and 0.60mx0.45m cast iron manhole cover with

frame weight not less than 35 kg as per directed by

Engineer-in-charge

132 Providing and installation Recharge pit of “RAIWOHA” 1.00 Nos. 109645.60

Make 3 layer RCC Precast Injection well system of size

1.5 meter Dia. X 3.4 Meter Height rein forced concrete

precast three layer module with 6” dia x 12” dia. V wire

screen of 0.75mm x 1.0 mm Slot size in SS 304 material

and 1.0 meter height with MS Top cover and required Air

vent including all necessary excavation and

transportation at site including required filter media for

the recharge system as per site requirement.

133 Supplying of well rotted FYM manure with all lead and 57.00 Cum. 378.75

Lift including spreading mixing dressing and rolling with

hand roller etc. complete.

134 Scarifying the surface of Soil including spreading of DAP 2249.00 Sqm 26.26

fertilizer mixing with Soil properly levelling gand

dressing of the plot

135 Supplying and planting Dibbing semi carpet lawn at 2249.00 Sqm 20.20

distance of abour 15 cm x 15 cm after proper anti termite

teratment amd rolling the seme by hand roller amd

wetering etc complete.

136 Bowing and developing flowering plants grown in nusery 25.00 No. 30.30

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith of soil packed in

polithyline bag or Earthern pot. Including organic &

chemical fertilizer Pesticides, fungicides, hormones &

maintaining the plants up to three months as deserted.

Bottol palm.

137 Bowing and developing flowering plants grown in nusery 20.00 No. 60.60

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as deserted Trinagle Plan.

Item Rate In

Description of Item Quantity Unit Amount

No figures

138 Bowing and developing flowering plants grown in nusery 10.00 No. 60.60

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as Jasud

139 Bowing and developing flowering plants grown in nusery 15.00 No. 75.75

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as Croton

140 Bowing and developing flowering plants grown in nusery 10.00 No. 10.10

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as deserted green mahindi

141 Bowing and developing flowering plants grown in nusery 10.00 No. 15.15

having approximate height 4 to 5 ft or Height ad per

Landscaps Plan with natural growith and nature colour

planted in alump of soil packed in polithyline bag or

Earthern pot. Including organic & chemical fertilizer

pesticides, fungicides hormones & maintaining the plants

uo to three months as deserted New block ficus.

142 Labour charges for planting various plantsafter proper 90.00 No. 40.40

anti termite treatment in pits including placing property

and filling the pit with requred prepared mix soil and

wetering and dispporting etc complete.

143 Maintance of the garder for 60 days after Complition of 3 1.00 Job. 10100.00

month stipulated period is completed for plantation o

lawn and plants including applying second round of

proper antitermite tretment.

144 Providing and fixing brass screw doen stop cock (A) 15 1.00 Rmt 287.85

145 Rubber Hose pope 15 mm dia of approved brand and 100.00 Rmt 80.80

146 Providnig and fixing G I Nipple as directed. 1.00 No. 20.20

Item Rate In

Description of Item Quantity Unit Amount

No figures

147 Supplying FIRE bucket round bottom of 9 litres capacity 20.00 No 1212.00

made out of 24 gauge G.I Sheet with extra handle at

bottom duly painted white inside and Red out side with

FIRE mark. Filled with dry-sand and kept on existing

stand provided or hung on wall hook.

148 Supplying and erecting floor mounting Stand for keeping 5.00 No 6565.00

four nos. of FIRE buckets comprising 1500 mm in length,

900 mm height frame made out of 30mm x 30 mm x

mm angle iron with cross suports legs, welded with

hooks and duly painted with one coat of red lead and two

coats of approved enamelled silver paint.

149 Design , Supply and installation of Safety Signage made of 9.00 sqmt 17220.53

Zinc Sulphilde based glow in dark , Rigid sheet with High

Luminous property enclosed in a transperent weather

proof UV stabilized plastic pasted on 3 mm thick clear

acrylic sheet such as EXITS, EMERGENCY EXIT, DO NOT

USE LIFT DURING FIRE, FLOOR MARKINGS, FIRE LIFT,

STAIRCASE EXIT, FIRE ALARM CALL POINT, FIRE HOSE

REEL, FIRE HYDRANT POINT etc.

150 Supply, Filling and Fixing of approved make ABC type 15.00 No. 2323.00

fire extinguisher - 6 Kg. Capacity as per IS:15683 & IS :

151 Supply, Filling and Fixing of approved make CO2 type 15.00 No. 6514.50

fire extinguisher. Capacity 4.5 Kg. (conforming to IS-

152 Submitting the application to obtain Fire NOC for one 1.00 No. 60600.00

year to SMC Department,Providing complete practical

demonstration of fire system in presence of fire officer

and Submitting the photographs of demonstration,

refilling and testing certificates of fire

extinguisher,Obtaining and providing certificate of

FPCOR, Payment of NOC Fees to SMC Department,

Preparing the documents of Affidavit and AMC with

Notorization And Submitting to Department, follow up to

receive NOC And Providing to R & B Including all above

expenditure.

Item Rate In

Description of Item Quantity Unit Amount

No figures

153 Point wiring for Light / Bell with 2-1.5 sq.mm & earth 136.00 Pt. 485.81

wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up

to 10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe

erected, with necessary Lamp holder/ceiling rose /

H.D.Connector as directed. (f) with medium class Rigid

PVC pipe and accessories erected concealed in

wall/ceiling complete Cat. III

154 Point wiring for Modular secondary light point with 2- 38.00 Pt. 167.66

1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of

ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires, in below type of pipe to be erected

complete with earth continuity and necessary connection

with primary light with accessories erected on Metal /

PVC / wooden box covered with 3 mm thick

PC(Polycarbonate) / Acrylic sheet for open / concealed

wiring. with necessary Lamp holder / ceiling rose /

H.D.Connector as directed.Note:- Maximum up to 6 mtrs

length, excess will be considered as Mains for Secondary

Point. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete

155 Point wiring for Two Way Controlled Light Point with 2- 14.00 Pt. 603.98

1.5 sq.mm & earth wire of 1.5 sq.mm (green) both are of

.ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires erected in below type of pipe with

6A Modular type switches and following type of

accessories erected on PVC / Metallic/Wooden box,

single mounting base frame covered with textured /

metallic/white front plate modules erected on / in wall /

ceiling as per pipe erected. with necessary batten/angle

holder or ceiling rose or H.D.Connector as directed. (f)

with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat III

Item Rate In

Description of Item Quantity Unit Amount

No figures

156 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 24.00 Pt. 674.68

1.5 sq.mm (Green) both are of .ISI marked 1.1 KV Grade

FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate

modules erected on / in wall / ceiling as per pipe erected.

with necessary ceiling rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete Cat. III

157 Point wiring for on board Looped Plug with 6A Modular 43.00 Pt. 257.55

type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured / metallic/white front plate

modules erected on / in wall / ceiling with following

type accessories Cat. III

158 Providing following type of Modular Type Accessories 42.00 Ea. 151.50

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (1)One No. SP 6 Amp. Cat.III

159 Providing following type of Modular Type Accessories 42.00 Ea. 151.50

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (2) One No 5 pin plug Cat.III

160 Providing following type of Modular Type Accessories 9.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (3) Two Pin/RJ-11 Telephone Socket.

[A] For One Gang Cat.III

161 Providing following type of Modular Type Accessories 73.00 Ea. 25.25

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (7) Blank Plate Single Cat.III

Item Rate In

Description of Item Quantity Unit Amount

No figures

162 Providing following type of Modular Type Accessories 10.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (8) Computer RJ-45 socket Cat.III

163 Providing following type of Modular Type Accessories 6.00 Ea. 160.59

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (4) TV Co-axial Socket outlet

164 Providing following type of Modular Type Accessories 17.00 Ea. 180.79

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (9) 16 Amp. SP one way switch

165 Providing following type of Modular Type Accessories 38.00 Ea. 199.98

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (10) 6/16Amp. Universal socket

166 Providing following type of Modular Type Accessories 21.00 Ea. 410.06

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (14) 16A Double Pole Modular MCB

Switch Cat.III

167 Providing following type of Modular Type Accessories 5.00 Ea. 360.57

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (16) 32 Amp. DP Main Switch

Operating with Energy Key Tag Cat.III

168 Providing following type of Modular Type Accessories 7.00 Ea. 329.26

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (19) Modular Indicating Call Bell

Item Rate In

Description of Item Quantity Unit Amount

No figures

169 Providing following type of Modular Type Accessories 5.00 Ea. 494.90

mounted with PVC / metallic/Wooden box, single

mounting base frame covered with textured /

metallic/white front plate , modules erected with

necessary connections as per site situation directed by

Engineer In charge. (21) Foot Light as per colour

requirement with concealed box, modular accessories,

acrylic glass cover with suitable LED watt with all

accessories as per following module (b) Four modules

170 Providing and erecting ISI mark Medium class RIGID PVC 655.00 Mtr. 24.24

PIPES of following size complete to be erected on/in wall

or ceiling erected with necessary PVC fittings & Junction

boxes fixed with adhesive solution & Clamps with

following dia of pipes, in approved manner as directed

171 Supplying and laying UPVC cable trunking system 10.00 Mtr. 277.75

comprising unplasticised polyvinyl, chloride rigid

material with ignition free and flame proof confirming BS

with necessary end caps Internal and external bend, flat

bends, coupler, tee etc..All necessary accessories and

measuring of following sizes (1) 75 mm x 50 mm

172 Providing and fixing approved make Perforated C type 5.00 Rmt. 622.16

cable tray. Made from sheet steel. The cable tray should

be single or double bended as per required and as per IS

2062/1079 and shall be coated with hot dip galvanizing

as per IS 2629/4759. with max 17.5% perforation with

coupler plate / Fish plate and GI hardware like nut - bolt

and washers etc. erection with necessary support(

included) as per Specification and as per instruction of

engineer in charge.. (5) 300 X 50 X 2.0 mm Thick

173 Providing and erecting Mains with 1.1 KV grade FRLS 1504.00 Mtr. 82.82

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green

colour for earth continuity of following size (A) With

medium class Rigid PVC pipe and accessories (b) 2 wire

174 providing and erecting Mains with 1.1 KV grade FRLS 425.00 Mtr. 112.11

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class Rigid

PVC pipe and accessories (a) 2 wire 4 sq. mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

175 providing and erecting Mains with 1.1 KV grade FRLS 90.00 Mtr. 147.46

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class Rigid

PVC pipe and accessories (b) 2 wire 6 sq. mm

176 providing and erecting Mains with 1.1 KV grade FRLS 90.00 Mtr. 260.58

PVC insulated ISI marked stranded Copper conductor

wire in following type of pipe to be erected in / on wall /

ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) with medium class Rigid

PVC pipe and accessories (h) 4 wire 6 sq. mm

177 providing and erecting Mains with ISI marked, 1.5KV 35.00 Mtr. 56.56

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required.

(e) One wire 6.00 sq. mm

178 providing and erecting Mains with ISI marked, 1.5KV 12.00 Mtr. 236.34

grade electrolyte multi stranded, annealed copper

conductor with heat resistant PVC insulated conforms to

IS 694, IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with

required size of copper lugs, nuts and bolts if required.

(h) One wire 25.00 sq. mm

179 Supplying and erecting Flexible PVC insulated multi 108.00 Mtr. 22.22

strand multi core 1.1 kv grade ISI marked copper wires

of following size to be erected as directed. (c) 1.00 Sq.mm

2 core round/ flat PVC sheathed

180 Supplying and erecting Flexible PVC insulated multi 54.00 Mtr. 46.46

strand multi core 1.1 kv grade ISI marked copper wires

of following size to be erected as directed. (e)

Sq.mm 3 core round PVC sheathed

181 Providing & Erecting approved make following size of TV 160.00 Mtr. 39.39

Co-axial flexible cable comprising inner conductor of

solid bare copper insulated with Foam PE & Secondary

conductor made of poly - Aluminium film bonded Al.

Braids @ suitable coverage overall sheathed with black

PVC insulation. (b) RG-6

Item Rate In

Description of Item Quantity Unit Amount

No figures

182 Supplying & erecting approved make Telephone Cable 40.00 Mtr. 199.98

electrolytic copper conductor PE insulation twisted in

two pairs, & wrapped with FRLS PVC tape & sheathed

with FRLS PVC or HFFR outer Jacket suitable for

telephone wiring & confirming to C-DOT erected in

existing pipe. of following size of conductors & nos.of

pairs. With necessary connections. (b) Armoured [Jelly

Filled] (2) Twenty Pairs

183 Supplying & erecting approved make LAN cable of 520.00 Mtr 76.76

following size in existing pipe as per direction [D] CAT -

184 Providing & erecting main Distribution (MDF) indoor 1.00 Ea. 1368.55

type, back mounted frame as per DoT standard approved

with krone strips (b) Suitable for 20 pair

185 Providing & erecting Switch board for Computer or 10.00 Ea. 1133.22

electric apparatus consisting of following modular type

accessories mounted with PVC / Metallic

concealed/open box with single mounting base frame

covered with textured/metallic /white front

plate,modules erected with necessary connections as

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories Cat.

186 Decorative call bell Ting-tong box type 250 volts 9.00 Ea. 71.71

complete erected

187 Supply & fixing decorative Hanging light with glass 10.00 Ea. 1797.80

having cylindrical or square shape having length not less

than 10" & width not less 3.5" with holder, lead wire as

per required length but not more than 1mm & base plate

for fixing the fitting with ceiling.[a] suitable for led lamp

Item Rate In

Description of Item Quantity Unit Amount

No figures

188 Supplying and erecting LED indoor fittings with LEDs of 8.00 Ea. 535.30

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/ aluminium die

cast powder coated and high U.V. & corrosion resistance

with diffuser with company mark/name 160V to 270V,

Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage

any wattage capacity between the ranges shown.) (A)

Tube Light with integral driver (v) 36-40 Watts, Surge-2

KV, IP-20, conventional 4 feet Cat-lll

189 Supplying and erecting LED indoor fittings with LEDs of 99.00 Ea. 758.51

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. &

corrosion resistance with diffuser housed in aluminium

casted body with company mark/name 160V to

270V,Power Factor more than 0.95, THD < 15 %,CCT

3000 K to 6500K, Luminaire efficacy> 85 lumens/watt

,LED driver efficiency > 85 %( fitting required LM-79 &

LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

between the ranges shown.) (A) Square/ Circular shaped

Surface/Recessed Mount Downlight with provision for

spring loaded mounting clips complete.IP20 (iv) 22-24

watts, Surge-2 KV Cat-lll

Item Rate In

Description of Item Quantity Unit Amount

No figures

190 Supplying and erecting LED indoor fittings with LEDs of 13.00 Ea. 312.09

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. &

corrosion resistance with diffuser housed in aluminium

casted body with company mark/name 160V to

270V,Power Factor more than 0.95, THD < 15 %,CCT

3000 K to 6500K, Luminaire efficacy> 85 lumens/watt

,LED driver efficiency > 85 %( fitting required LM-79 &

LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The

between the ranges shown.) (H) Mirror Light 9 Watts,

wall mounted minimum 1 feet long

191 Supplying and erecting led lamps with following wattage 3.00 Ea. 112.11

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 / B22 lamp

holders, pf >= 0.5 (A) LED Lamps integral type, with PC

diffuser suitable LAMP holder (ii) 5 to 8 watts Cat-III

192 Supplying & erecting approved make low noise 8.00 Ea. 1703.87

decorative exhaust fan having square frame ABS body

with inbuilt lowers & square frame. 200mm with

1350RPM Cat.II

193 Providing and erecting decorative wall bracket fittings 33.00 Ea. 1712.96

complete with LED lamp and rust free fittings

components mounted in chrome finish housing with

holder ,clear/opaque glass diffuser complete erected

with lead wires with minimum 15 wattage capacity as

per instruction engineer incharge/architect/authority

Item Rate In

Description of Item Quantity Unit Amount

No figures

194 Supplying and erecting LED street light / Flood light 9.00 Ea. 5976.17

fittings with High power White LEDs wattage of 3 Watt

and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated

and heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened glass with

company mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %, CCT

K to 5700K,Uniformity ratio >0.45, Luminaire efficacy>

100 lumens/watt . LED driver efficiency > 85 %.( fittings

required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of

wattage capacity between the ranges shown.) (A) Street

Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage

protection. (iii) Above 60 to 90 watts Cat-lll

195 (C) Post Top Lantern LED fitting comprises of finish cast 2.00 Ea. 4819.72

aluminum spigot and spun aluminum canopy fixed with

opal polycarbonate, pipe arrangement for vertical

mounting driver and accessories wired upto terminal

block.IP 65(ii)32-40W Cat-lll

196 Providing & erecting Approved make Ceiling Fan with 12.00 Ea. 2311.89

double ball bearing ISI mark with Condenser 230 volt

A.C.50 Hz 1200 mm sweep complete having 3 blades

aluminium body and blade sets having ornamental

design shanks , canopy erected with earthing. [ Make

shall be approved by Engineer in Charge]

197 Providing & erecting Approved make Ceiling Fan with 5.00 Ea. 1982.63

double ball bearing with Condenser 230 volt A.C.50 Hz.

900 mm sweep complete having 3 Aluminium blades,

canopy erected complete. [ Make shall be approved by

Engineer in Charge]

198 Providing & erecting Approved make Power Saving 50 7.00 Ea. 1948.29

Watt Ceiling Fan with double ball bearing ISI mark with

Condenser 230 volt A.C. 50 Hz 1200 mm sweep

complete having 3blades with aluminium blades with

canopy & 30 cm. down rod erected with earthing.(Make

shall be approved by Engineer in charge))

199 Supplying and erecting 19 / 20 mm. nominal bore 24.00 Mtr. 108.07

Medium Class M.S. Pipe down rod erected duly painted

for fan complete with proper insulation without leakage

and earthing.

Item Rate In

Description of Item Quantity Unit Amount

No figures

200 Supplying & erecting fan hook box of 10 mm M.S. round 24.00 Ea. 108.07

bar bounded to the RCC bars up to 50mm length each

side and pierced through a 16 Gauge M.S. box / Heavy

Duty PVC box complete erected concealed in Ceiling with

necessary finishing.

201 Providing 2.5mm.thick laminated acrylic sheet to cover 24.00 Ea. 18.18

the fan hook or Fan box.

202 Providing and erecting XLPE(IS:7098)(I)-88 ISI 140.00 Mtr. 540.35

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (F)

1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core)

203 Providing and erecting XLPE (IS:7098)(I)-88 ISI 276.00 Mtr. 126.25

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with necessary

clamps or in existing trench / pipe of following size of

cables (B) 4 core 6 Sq. mm

204 Making trench in soft soil of suitable width of 90 cm deep 351.00 Mtr. 55.55

for laying cable or locating the fault all over the run and

back filling the same and making the surface as normal

205 Providing & laying. R.C.C. Hume pipe for cable to be laid 10.00 Mtr. 226.24

90 cm. below ground across the road crossing or on floor

with necessary material in an approved manner and

making the ground as per original. (F) 100 mm dia.

206 Providing & laying approved make Double walled 221.00 Mtr. 62.62

corrugated pipes (DWC) of polyethylene(conforming to

IS 14930 II )with necessary connecting accessories of

same material at required depth in existing trench for

laying of cable. below ground / road surface for

enclosing cable (A)50 mm outer dia

207 Providing & laying approved make Double walled 80.00 Mtr. 137.36

corrugated pipes (DWC) of polyethylene(conforming to

IS 14930 II )with necessary connecting accessories of

same material at required depth in existing trench for

laying of cable. below ground / road surface for

enclosing cable (D)120 mm outer dia.

208 Providing and, fixing heavy duty flange type brass cable 5.00 Ea. 38.38

gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc for

following size of cables. (B) 2 to 4 core 6 Sq. mm

Item Rate In

Description of Item Quantity Unit Amount

No figures

209 Providing and, fixing heavy duty flange type brass double 8.00 Ea. 140.39

compression type cable gland with rubber ring for PVC

insulated armoured cable complete with out going tails,

insulating tape etc for following size of cables. (E) 3 &

1/2 core 120 Sq. mm

210 Solder less crimping type Aluminium lugs conforming to 28.00 Ea. 6.06

IS suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (A) 6 Sq.mm

211 Solder less crimping type Aluminium lugs conforming to 4.00 Ea. 25.25

IS suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (E) 70 Sq.mm.

212 Solder less crimping type Aluminium lugs conforming to 12.00 Ea. 45.45

IS suitable for cable of following size evenly crimped with

high pressure tool & connected to switchgear terminals

with brass/cadmium plated nut bolts in an approved

manner. (G) 120 Sq.mm.

213 Providing and erecting Approved make Four pole 2.00 Ea. 6173.12

moulded case circuit breaker having breaking capacity

ICU of 25 KA. at 415 V,having normal current rating up to

25 A to 100A. with Fixed thermal & magnetic release

suitable to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected

in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III

214 Providing and erecting Approved make Four pole 3.00 Ea. 16221.61

moulded case circuit breaker having breaking capacity

ICU of 35 KA. at 415 V. having Normal current rating

200A.with variable Thermal & magnetic release suitable

to work on A.C.supply 50 c/s. with all internal

connections, spreader tinned copper & complete erected

in existing 16 G.M.S.housing ICS=100% of ICU only

215 Supplying & erecting approved make Four Pole 415V 1.00 Ea. 12241.20

change over switch interior for panel mounting with

operating mechanism A.C.23 duty confirming to IS for

(D)200A Cat-lll

Item Rate In

Description of Item Quantity Unit Amount

No figures

216 Supplying and erecting triple pole & neutral 440V / 500V 2.00 Rn.Mtr 3202.71

panel mounting Copper Busbars with four equal Nos. of

electrolyte bus having current density not more than

Amp. / sq.mm (Rated current / cross section area) duly

wrapped with colour insulating tape for phase sequence

of following current carrying capacity, erected with

necessary bus bar supports /insulators, main cable

socket to each bar, erected in existing cubical panel with

necessary connections. (B) Suitable for 200 Amp.

217 providing and erecting Miniature circuit breaker single 71.00 Ea. 112.11

pole 6A to 25A suitable to operate on 240 V A.C. system

and having breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with ISI Mark

218 Providing & erecting 240 V MCB double pole switch for 3.00 Ea. 278.76

lighting Load (B Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following

capacity (A) 6 to 32 Amp. Cat.III

219 Providing & erecting 240 V MCB double pole switch for 7.00 Ea. 295.93

lighting Load (B Curve) having 10 KA breaking capacity &

confirms to IS : 8828 in existing box having following

capacity (B) 40 Amp. Cat.III

220 providing and erecting Approved make RCCBs 5.00 Ea. 1969.50

conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz.

having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed

(i) 25 Amps.DP Cat. III

221 providing and erecting Approved make RCCBs 12.00 Ea. 2235.13

conforming to IS: 12640 and having sensitivity of 30 mA

and Short Circuit withstand capacity of 10 KA and

suitable for operation on single phase 240 V,50Hz.

having characteristic of quick action & tripping with all

advance feature & do not incorporate any electronic

component. for following Max. rating erected as directed

(ii) 40Amps. DP Cat. III

222 Providing & erecting 415V MCB Four Pole Switch for 4.00 Ea. 638.32

Lighting Load (B curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following

capacity (b)40 Amp. Cat.III

223 Providing & erecting 415 V MCB Four Pole for Motor & 8.00 Ea. 737.30

Inductive Load (C Curve) having 10KA breaking capacity

& confirms to IS :8828 in existing box having following

capacity (c)63 Amp. Cat.III

Item Rate In

Description of Item Quantity Unit Amount

No figures

224 Sheets steel powder coated enclosure suitable for 5.00 Ea. 176.75

incorporating One/Two nos. MCB.

225 Providing and erecting Sheet Steel powder coated MCB 3.00 Ea. 1492.78

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to

IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for (A) single

phase incoming and horizontal single phase outgoing (b)

sheet steel double door (IP-43) (iv)12 way

226 Providing and erecting Sheet Steel powder coated MCB 3.00 Ea. 2339.16

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to

IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of

same company of MCB to be used) suitable for (B) three

phase incoming and single phase horizontal type

outgoing Per phase isolation type (PPI) (b) sheet steel

double door (i)4 way

227 Providing and erecting Annealed bare Copper wire 8 to 4.00 Kg. 794.87

228 Providing and erecting HOT deep Galvanised iron strip 5.00 Kg. 77.77

wire 8 to 16 SWG.

229 Providing and erecting Pipe type earthing having 150 4.00 Ea. 368.65

cms.long and 2.5 cms. dia. galvanised iron pipe with

coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

230 For using salt and charcoal / coke as required for pipe 4.00 Ea. 171.70

type earthing.

Item Rate In

Description of Item Quantity Unit Amount

No figures

231 Supplying & erecting earth pit of minimum bore 2.00 Ea. 4591.46

dia.150mm size approved make Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer

pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for

following type of applications with chamber and heavy

duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of

installation duly stamped and signed by agency and

officer Incharge has to ensure the value of earthing

resistane mentioned in test Certificate) & having back

filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-

2017, Voltage drop:- < 1 volt at no load & dry form,

Sulphar content:- <2%(C) Back fill Compound :- Earthing

compound should be capable to retain moisture for long

time Necessary test report must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Item Rate In

Description of Item Quantity Unit Amount

No figures

232 Providing & erecting weather proof, dust & vermin proof, 2.40 Sq.Mtr 14902.55

floor mounted front operated indoor type cubical panel

board necessary IP-42 and above protection as per

approval from engineer incharge made from 14 SWG

thick CRC M.S. sheet for outer body & doors, 16 SWG

thick CRC M.S.sheet for internal partitions with necessary

accesories , supporting angles/ flats channel including

cutting, bending, drilling, welding, riveting with internal

partitions & cable alley as per requirements & instruction

of engineer-in-charge with erection of supplied switch

gears, BUSBARS, suitable size of inter connecting PVC

copper wire / copper-aluminium strips, rubber

grommets, rib, bakelite control fuses/MCB for measuring

instruments, earth bus & earth bolts, foundation flange -

bolts-base Plates, sufficient nos. of hinged doors, handles

with locking arrangement and rubber gasket,heavy duty

end terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be

painted with epoxy powder coating. (The rates excludes

the cost of switchgears, bus bars, inter connecting mains

& Copper Aluminium strips, meters, Fuses etc. The

dimension shall be measured excluding base beams) The

panel shall be supplied with following approved

manufacturers with following size. (B) The standard

companies switch gear shall be used and only

manufacturers at CPRI approved factory (i) with 350mm

233 Providing , erecting , fabricating the M.S. structure as per 40.00 Kg. 77.77

requirement on site incorporating proper size of M.S.

angles,square,round, flats, bars, channels, sections

complete with cutting, welding, grinding & finishing duly

painted with one coat of red oxide with erection on site

as per direction of engineer in charge with necessary

grouting, cementing, plastering & finishing complete.

Item Rate In

Description of Item Quantity Unit Amount

No figures

234 Supplying and erecting approved make Octagonal pole 9.00 Ea. 8192.11

made from HR sheet steel. The pole should be made as

per IS. and shall be coated with hot dip galvanizing as per

IS 2629/2633/4759, suitable suspend local wind speed

with integral Junction box consist of terminal plate of min

6mm Hylam sheet, standard profile 35mmX7.5mm Din-

Rail for MCB Mounting, stud type terminal and

arrangement for cable termination to be erected With

Suitable foundation (Included) as per details given by

manufacturer considering site requirement. (D) 6 Mtr.

Long 70 mm Top X 135 mm bottom dia, 3 mm thickness

with 200mmX200mmX12mm base plate, 4-M20 Bolts

and 600mm long with necessary G.I. J Bolts .Approx Pole

weight 59 kg

235 Supplying & erecting approved make SMC press 2.00 Ea. 515.10

moulded composite FRP. loop-in, loop-out approx. 2mm

thick box complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged

doors as per requirement having locking arrangements

with mounting clamp with nuts, bolts & washers suitable

for erection on pole with cable clamps& earth bolt of

following size of box. (B) 250mm x 200mm x 100mm

236 Supplying and erecting Street light pole bracket 9.00 Ea 491.87

comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I. sleeve

tubing of approx. 45cms.length and suitable for

76.5mm/80mm/require size of pole top having nuts and

bolts for fixing the brackets and having spread of 0.5 mtr.

Length with 110 deg.with vertical plane and suitable

welded stiffener reducer and nipple with check nut

complete painted with one coat.of Red oxide / PU base

primer and two coats of Aluminium / PU paint. paint

with following nos of arms. [A] Single Arm bracket

Item Rate In

Description of Item Quantity Unit Amount

No figures

237 SITC of Digital / PCM / TDM EPABX System having SMT 1.00 Ea. 45398.49

design, system with flexible universal slots. Inbuilt Auto

attendant facility, Minimum 15 Nos. conference, Analog

extension line, Calling GSM, E&M line, PRI / EI & VOIP

program me through Analog telephone digital key from

Ethernet, public address cord, shall have unrestricted

simultaneous dialing facility,

QSIG protocol on PRI, 95 / STD / ISD / Local-Locking,

Class of Service, Quick Dial-Single Digit dialing of any two

external number, Once only ring device, Chairman /

Secretary - Do not disturb Facility, Power Down Mode,

Hot Line, Hot Outward Dialing, Day Night Mode, Auto Call

Back, Barge-in, Call Pick Up & Call Transfer, Call transfer

while Ringing with Voice Guide System, (DISA), Caller ID

(CLI), CLI Base ECF, CLI Base routing Internet Ready Port,

External Music Port, Call Budgeting, Call Most Calculation

(ASMDR), DID Direct Inverse Dialing, External Music

Input, Fax Homing, Global Directory Printing with

following capacities [[Approved by Competent Authority

i.e. not Below the rank of Executive Engineer ] [A] No of

Extension 16, No of Junctions 6, 8 Port IP Resource in-

built, 4 Port Web base Video Conferencing, No of

expandable ports : 48, Operators Console -

Compatible : ISDN

238 Supplying & erecting push button type telephone 9.00 Ea. 898.90

instrument having speaker phone Caller ID & speaker

phone with one touch memory (min.6 nos.)&

memories with display system Single line [[Approved by

Competent Authority i.e. not Below the rank of Executive

Engineer ]

239 Providing & erecting water cooler having storage 1.00 Ea. 55893.40

capacity 150 Ltr. & cooling capacity 150 Ltr.per hour @

an ambient temp of 45˚ C. The outlet temp. of the water

should drop by 15˚C within a hour, The water cooler

should be comprising of hermetically sealed compressor,

fan motor, condensing unit, water tank surrounded by

evaporating, coil, thermostats, relay etc.complete with

necessary inlet & outlet connection. The body of water

cooler will be made from Stainless Steel.

Item Rate In

Description of Item Quantity Unit Amount

No figures

240 Supplying & erecting 5 stage single reverse osmosis 1.00 Ea. 29187.99

water purification system with M.S. powder coated

frame, prefilter housing with 'O' ring presediment filter

GAC filter, carbon filter suitable buster DC pump capacity

80 psi, mention with 40 psi inline type post carbon filter

auto low & high pressure switches with following size of

storage tank & LPH capacity & erected as directed [C]

Ltr / Hr with 150 psi 2 nos booster pump

241 Providing and erecting Inverter based approved make 2.00 Ea. 48257.80

split air-conditioning unit consisting of condensing unit

with variable speed fan motor, inverter type hermetically

sealed rotary compressor with accessories etc. duly

connected separately erected evaporating unit and

blower motor with its accessories by means of extra

supplied proper insulated copper tubing,drain PVC pipes

suitable for ( cost includes Eco Friendly green gas

charging and 15A plug top & Remote Control & MS

Stand) with necessary core cutting. (1)For ISEER Range

(KWH/KWH)(3.1 to 3.99) (B) for 1.5 ton capacity-

Premium Cat.

242 Providing and erecting Inverter based approved make 7.00 Ea. 56353.96

split air-conditioning unit consisting of condensing unit

with variable speed fan motor, inverter type hermetically

sealed rotary compressor with accessories etc. duly

connected separately erected evaporating unit and

blower motor with its accessories by means of extra

supplied proper insulated copper tubing,drain PVC pipes

suitable for ( cost includes Eco Friendly green gas

charging and 15A plug top & Remote Control & MS

Stand) with necessary core cutting. (1)For ISEER Range

(KWH/KWH)(3.1 to 3.99) (C) for 1.7 to 2 ton capacity-

Premium Cat.

243 Supplying and erecting insulated pair of soft copper 63.00 Ea. 965.56

tubing open or concealed including power and control

cable,necessary PVC drain pipes for Split AC machine up

to 4 TR capacity

244 Supplying and erecting approved make Single phase 9.00 Ea. 3232.00

power conditioners suitable for input voltage 180V /

280V, output voltage 220V (+ / - 10%) AC 50 ‘Hz with

electronic relays & component of housed in sheet metal

cabinet ‘with epoxy powder coated, with high - low cut-

universal socket with range off (D) 4 KVA

Item Rate In

Description of Item Quantity Unit Amount

No figures

245 Supplying and erecting horizontal / vertical mounting 5.00 Ea. 9513.19

type storage water heater with copper container housed

in M.S./S.S./ABS body insulated with glass wool/puff

complete with heating elements,adjustable thermostats

300C to 850C, indicating lamp, safety valve, fusible plug,

etc.complete erected with coach bolts, nuts. washers &

cementation (B)15 Ltr-.with 2 /3K.W. heating element

Premium Category

246 Supplying and erecting approved make panel mounting 2.00 Ea. 1275.63

type Digital Voltmeter having 3 digits LED display, 0 to

750 AC Volts range erected on existing panel board with

all connection, wiring etc .with manufacturers calibration

certificate.

247 Supplying and erecting approved make panel mounting 2.00 Ea. 1558.43

type Digital Ammeter having 3 digits LED display,

external CT operated, calibrated for 0 to 1000 Amps

suitable to operate on 500 Volt AC , erected on existing

panel board with all connection, wiring etc .with

manufacturers calibration certificate.

switch for 3 phase AC Supply 500 V on existing panel

board with necessary connections.

249 Providing & erecting L.T. Current Transformer with bar 6.00 Ea. 274.72

primary 50/5 to 1000/5 ratio 15 VA burden erected in

existing CRCA box duly secured with insulating materials

connected to the meter

250 Supplying and erecting approved make suitable panel 6.00 Ea. 43.43

indicator LED type lamp, lens cover, complete erected

with necessary connections.

Total Rs.

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and

words) of the estimated rate mentioned above. Amount of my /our

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

Item Rate In

Description of Item Quantity Unit Amount

No figures

The Contractor shall exhibit a board with detailed specification and details of work as directed by the

1 Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

4 there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

Deputy Executive Engineer Executive Engineer

Dharampur ( R & B ) Sub Division Valsad ( R & B ) Division

Dharampur Valsad