SPECIAL REPAIR FOR REPLACEMENT OF BER DG SETS, TRANSFORMERS, SUBMERSIBLE PUMPS, PASSENGER LIFTS, SPLIT TYPE AC AND WATER COOLER AT TECHNICAL AREA, PUMP HOUSE ETC, AT DEAL COMPLEX, UNDER GE (I) RnD DEHRADUN

Amount

(a) Stops and Openings : 3 stops / 3 openings on the same side. (b) Type of lift: Traction passenger machine room lift (c) Travel height: Three floor (G+2) Official (technical) bldg height (d) Traction media: Belt with embedded stranded steel rope inside polyethylene coating/round stranded steel wire rope conforming to IS 14665-2000 with guards. (e) The integral dimension of the lift car shall be of suitable size for the specified load and as per IS 4666-2000 as amended to date. (f) The inside car measurement shall be based on existing lift well. 1. Lift shall be complete with and including following Technical Specifications:- (i) Lift car speed 1.5 m/s (ii) Machine: Gearless Machine (Permanent Magnet) with electric operated single speed motor on power supply 415 Volts, 3 Phase, 50 Hz. (iii) Car door:- 2 panel automatic centre opening door with ACVF drive in stainless steel (iv) Landing door:- 2 panel automatic centre opening door in stainless steel (v) Double button with 6 segment digital LED display at all floors. (vi) Car operating panel with micro stroke push button with 6 segment digital car position indicator, car direction indicator. (vii) The safety controls and indicator shall be as per standard practice and based on infra red sensors. (viii) The testing of lift with 25 % excess load shall be conducted as per para 25 of IS 4666-2000 as amended to date. The arrangement for testing load for testing and instrument required shall be arranged by contractor. (ix) Fireman’s switch provided at main lobby. (x) Battery operated alarm bell and emergency light with battery. (xi) Lift announcer. (xii) Adjustable door open time (xiii) Provision of cross flow rectangular (low noise/mildair flow) fan – 01 (xiv) S & F Decorative spot round shape LED light (xv) Door open and door close buttons in car operating panel

(xvi) Intercom (xvii) Jammed landing operating panel call button by-pass (xviii) Phase failure and phase reversal protection (xix) Motor overheat protection (xx) Overload function with audio-visual indication in car operating panel (xxii 5/15 A power socket & light point at every floor level in the hoist way. (xxii) MS Ladder (xxiii) 3 Phase supply & earthing from machine room to all equipment. (xxiv) Firemen emergeny return (xxv) The words "FIRE LIFT" and "IN CASE OF FIRE ONLY FIREMAN SHALL OPERATE THE FIRE LIFT" shall be pasted in bold letters on PVC sheets at all floor levels.

2. Other standerd safety device features required (a) Multi beam full length criss crossing each other infrared door sensor (minimum of 154) (b) Emergency landing device ELD (ARD) (c) Extra cores in travelling cable for customer smoke detectors.- 02 Cores (d) Background music speakers (e) Digital direction and position indicator in car and at all landings. (f) Emergency alarm at the main landing with alarm bell button in car (g) 2 Phase/ 2 way fire man drive, fire man switch at the main landing. (In case fire man drive is activated the lift will come to the main landing and open the door) (h) Advance door operation (To ensure smooth opening and closing of the doors at adjustable door speed) (j) Load weighing device (Audio visual overload indicator in the car for better safety) (k) Over speed governor (Electro mechanical device that prevent free fall in case the elevator is travelling at speed more than 10% of the rated speed in downward direction) (l) special car door lock, automatic dailly brake testing, latest technology motor-PMS touch panel with LED display (m) Mechanical rescue device with no dependence with battery (n) Door time protection with extra door time for lobby and parking, auto fan cut off (o) Controller shall be include protection against over current, over voltage, single phasing, phase reversal, earth leakage and interlocking with door opening, closing and moment of lift and any other operation required for the safety of passenger as per fire safety regulation pertaining to lift (p) Stainless steel hand rail all three walls of car (q) Key locking system D-type

Note:- (i) Contractor has to submit detailed construction drawings of lifts being provided with complete technical specifications as per IS:14665 before dispatch of material from OEM for approval of GE (ii) The lift shall be installed in replacement in existing lift well therefore contractor is advised to visit site for the size of car door, floor travelling height and left hand/right hand side wall space, existing head room height and pit size before quoting the rates. (iii) The scope of work also covered the civil work comprising cutting of holes and making good the surfaces, car and counter weight, guide rails and bracket , terminals buffers supports and sill angle, plates and any other items required for successful completion of lift with respect to safely required by the OEM, will be carried out by the contractor without any extra cost. (iv) The contractor shall be responsible for 2 years defect liability period from certified date of completion of GE. During the said defect liability period the lift shall be kept functional/serviceable all the time & all consumable items shall be provided by contractor for operation & maintenance of lift. All periodical maintenance regular check up/inspection should be carried out OEM during 02 years defect liability period in addition to regular checkups and periodical services special visit/inspection will also be carried to rectify defects by representative of OEM if any emergency / trouble developed. An agreement will be made between contractor & OEM and this shall be submitted to GE on the date of handing over to lift (date of completion) for the comprehensive maintenance of defect liability period. The cost of above shall be deemed to be included in the quoted rates. (v) The provision of suitable steel structure/platform for installation of lifts equipment is part of lift items and nothing extra shall be paid. (vi) If any clearance is required to seek from state Govt i.e. from lift inspector or electrical safety department or fire safety department is the constractor's responsibility & any expenditure on this account shall deemed to be included in the quoted unit rates.

Dismantling of Old unserviceable lift complete with panel board by disconnecting electrical connection etc including all accessories and depositing the same in MES store yard all as directed by Engineer-in-Charge.

Supply, installation, testing and commissioning Silent Diesel engine driven generating set complete with accoustic enclosure CPCB approved and control system for 62.5 KVA out put at site ie at MSL after de rating AC 415 Vollts, 50 C/S, 3 phase 4 wire directly coupled complete with self starting system with and including accessories, equipment control panel etc as detailed below:- (a) Diesel Engine :- Diesel engine water/coolent cooled and electric start suitable to drive mentioned alternator independently, coupled directly through coupling , four cylinder, 4 stroke, cold starting,1500 RPM industrial type as per BS:5514 or IS-10001/10002 and suitable to regulate speed of DG set from no load to full load complete with fuel tank of capacity as per manufacture's recommendations, fuel line exhaust pipe duly insulated with asbestos rope and with support and silencermufflers etc for continuous operation and standard accessories, sump pre heaters etc all as specified and directed. Air Intake System (i) Air intake mainfold, (ii) Dry type air cleaner, (iii) Vaccum indicator Exhaust System (i) Turbo charger, (ii) Flexible connection, (iii) Exhaust mainfold, (iv) Residential silencer Coolent System (i) Engine water pump, (ii) Radiator, (iii) Coolant additive concentrate Lubrication System (i) Oil pan, (ii) Engine mounted lube oil pump, (iii) Full flow spin-on lube oil filter Fuel System (i) Electronic Governor, (ii) 24 V DC Solenoid coil, (iii) Dual fuel filter system Starting System (i) 12 Volt DC electric starter (ii) 12 Volt DC battery charging alternator Make of Engine : Cummins/ Kirloskar/ Greaves.

Supply, installation, testing and commissioning Silent Diesel engine driven generating set complete with accoustic enclosure CPCB approved and control system for 125 KVA out put at site ie at MSL after de rating Ac 415 Volts, 50 C/S, 3 phase 4 wire directly coupled complete with self starting system with and including accessories, equipment control panel etc as detailed below:- (a) Diesel Engine :- Diesel engine water cooled and electric start suitable to drive mentioned alternator independently, coupled directly through coupling , four cylinder 4 stroke, cold starting,1500 RPM industrial type as per BS:5514 or IS-10001/10002 suitable to requlate speed of DG set from no load to full load complete with fuel tank of capacity as per manufacture's recommendations, fuel line exhaust pipe duly insulated with asbestos rope and with support and silencermufflers etc for continous operation and standard accessories, sump pre heaters etc all as specified and directed. Air Intake System (i) Air intake mainfold, (ii) Dry type air cleaner, (iii) Vaccum indicator Exhaust System (i) Turbo charger, (ii) Flexible connection, (iii) Exhaust mainfold, (iv) Residential silencer Coolent System (i) Engine water pump, (ii) Radiator, (iii) Coolant additive concentrate Lubrication System (i) Oil pan, (ii) Engine mounted lube oil pump, (iii) Full flow spin-on lube oil filter Fuel System (i) Electronic Governor, (ii) 24 V DC Solenoid coil, (iii) Dual fuel filter system Starting System (i) 12 Volt DC electric starter (ii) 12 Volt DC battery charging alternator Make of Engine : Cummins/ Kirloskar/ Greaves.

Supply, installation, testing and commissioning Silent Diesel engine driven generating set complete with accoustic enclosure CPCB approved and control system for 250 KVA out put at site ie at MSL after de rating AC 415 Volts, 50 Hz, 3 phase 4 wire directly coupled complete with self starting system with and including accessories, equipment control panel etc as detailed below:- (a) Diesel Engine :- Diesel engine water cooled and electric start suitable to drive mentioned alternator independently, coupled directly through coupling , six cylinder 4 stroke, cold starting,1500 RPM industrial type as per BS:5514 or IS-10001/10002 suitable to requlate speed of DG set from no load to full load complete with fuel tank of capacity as per manufacture's recommendations, fuel line exhaust pipe duly insulated with asbestos rope and with support and silencermufflers etc for contuious operation and standard accessories, sump pre heaters etc all as specified and directed. Air Intake System (i) Air intake mainfold, (ii) Dry type air cleaner, (iii) Vaccum indicator Exhaust System (i) Turbo charger, (ii) Flexible connection, (iii) Exhaust mainfold, (iv) Residential silencer Coolent System (i) Engine water pump, (ii) Radiator, (iii) Coolant additive concentrate Lubrication System (i) Oil pan, (ii) Engine mounted lube oil pump, (iii) Full flow spin-on lube oil filter Fuel System (i) Electronic Governor, (ii) 24 V DC Solenoid coil, (iii) Dual fuel filter system Starting System (i) 24 Volt DC electric starter (ii) 24 Volt DC battery charging alternator Make of Engine : Cummins/ Kirloskar/ Greaves.

Supply, installation, testing and commissioning Silent Diesel engine driven generating set complete with accoustic enclosure CPCB approved and control system for 320 KVA out put at site ie at MSL after de rating Ac 415 Vollts, 50 C/S, 3 phase 4 wire directly coupled complete with self starting system with and including accessories, equipment control panel etc as detailed below:- (a) Diesel Engine :- Diesel engine water cooled and electric start suitable to drive mentioned alternator independently, coupled directly through coupling , six cylinder 4 stroke, cold starting,1500 RPM industrial type as per BS:5514 or IS-10001/10002 suitable to requlate speed of DG set from no load to full load complete with fuel tank of capacity as per manufacture's recommendations, fuel line exhaust pipe duly insulated with asbestos rope and with support and silencermufflers etc for contuious operation and standard accessories, sump pre heaters etc all as specified and directed. Air Intake System (i) Air intake mainfold, (ii) Dry type air cleaner, (iii) Vaccum indicator Exhaust System (i) Turbo charger, (ii) Flexible connection, (iii) Exhaust mainfold, (iv) Residential silencer Coolent System (i) Engine water pump, (ii) Radiator, (iii) Coolant additive concentrate Lubrication System (i) Oil pan, (ii) Engine mounted lube oil pump, (iii) Full flow spin-on lube oil filter Fuel System (i) Electronic Governor, (ii) 24 V DC Solenoid coil, (iii) Dual fuel filter system Starting System (i) 24 Volt DC electric starter (ii) 24 Volt DC battery charging alternator Make of Engine : Cummins/ Kirloskar/ Greaves.

Supply, installation, testing and commissioning Silent Diesel engine driven trailer mounted generating set complete with accoustic enclosure CPCB approved and control system for 20 KVA output (mounted on suitable two wheeler trailer manufactured by OEM) at site ie at MSL after de rating Ac 415 Vollts, 50 C/S, 3 phase 4 wire directly coupled complete with self starting system with and including accessories, equipment control panel etc as detailed below:- (a) Diesel Engine :- Diesel engine water/coolent cooled and electric start suitable to drive mentioned alternator independently, coupled directly through coupling , two cylinder 4 stroke, cold starting,1500 RPM industrial type as per BS:5514 or IS-10001/10002 suitable to requlate speed of DG set from no load to full load complete with fuel tank of capacity as per manufacture's recommendations, fuel line exhaust pipe duly insulated with asbestos rope and with support and silencermufflers etc for contuious operation and standard accessories, sump pre heaters etc all as specified and directed. Air Intake System (i) Air intake mainfold, (ii) Dry type air cleaner, (iii) Vaccum indicator Exhaust System (i) Turbo charger, (ii) Flexible connection, (iii) Exhaust mainfold, (iv) Residential silencer Coolent System (i) Engine water pump, (ii) Radiator, (iii) Coolant additive concentrate Lubrication System (i) Oil pan, (ii) Engine mounted lube oil pump, (iii) Full flow spin-on lube oil filter Fuel System (i) Electronic Governor, (ii) 12 V DC Solenoid coil, (iii) Dual fuel filter system Starting System (i) 12 Volt DC electric starter (ii) 12 Volt DC battery charging alternator Make of Engine : Cummins/ Kirloskar/ Greaves.

Supply, installation, testing and commissioning Silent Diesel engine driven trailer mounted generating set complete with accoustic enclosure CPCB approved and control system for 12.5 KVA output (mounted on suitable two wheeler trailer manufactured by OEM) at site ie at MSL after de rating Ac 415 Vollts, 50 C/S, 3 phase 4 wire directly coupled complete with self starting system with and including accessories, equipment control panel etc as detailed below:- (a) Diesel Engine :- Diesel engine water/coolent cooled and electric start suitable to drive mentioned alternator independently, coupled directly through coupling , two cylinder 4 stroke, cold starting,1500 RPM industrial type as per BS:5514 or IS-10001/10002 suitable to requlate speed of DG set from no load to full load complete with fuel tank of capacity as per manufacture's recommendations, fuel line exhaust pipe duly insulated with asbestos rope and with support and silencermufflers etc for contuious operation and standard accessories, sump pre heaters etc all as specified and directed. Air Intake System (i) Air intake mainfold, (ii) Dry type air cleaner, (iii) Vaccum indicator Exhaust System (i) Turbo charger, (ii) Flexible connection, (iii) Exhaust mainfold, (iv) Residential silencer Coolent System (i) Engine water pump, (ii) Radiator, (iii) Coolant additive concentrate Lubrication System (i) Oil pan, (ii) Engine mounted lube oil pump, (iii) Full flow spin-on lube oil filter Fuel System (i) Electronic Governor, (ii) 12 V DC Solenoid coil, (iii) Dual fuel filter system Starting System (i) 12 Volt DC electric starter (ii) 12 Volt DC battery charging alternator Make of Engine : Cummins/ Kirloskar/ Greaves.

Supply , installed, testing and commissioning step down transformer, Copper wounded, Outdoor type complete with standard fittings HT 11 KV/433 Volts (at no load) 3 phase 4 wire, 50 Hz, 315 KVA capacity core type double copper wound, oil immersed. oil cooled, delta connected on primary side (HV) and star connected on secondary side (LV) in accordance with vector group DYN-11 with natural brought out on secondry side (LV side) and having tapping at + 7.5% in step of + 2.5% on HV side to be changed by means of hand operated off load tap changer gear. Oil temperature should not exceed 40 degree celsius above ambient temperature and HV/LV winding temperature should not exceed 45 degree Celsius when measured by resistance method after continous full load run on an ambient temperature of 50 degree Celsius. The Transformer shall be IS- 1180, level II marked and shall comprises of the following :- (a) Three Nos porceian bushing suitable for 11 KV on HV side complete with copper rods, nuts and washers. (b) LT side (Secondary side) consisting of four Nos porcelain bushing with copper rods, complete with nuts and washers with cable glands (c ) Oil conservator with filter type drain valve and oil level gauge (d) De- hydrating breather with first type fill of dehydrating agent (Silica Gel) (e) Explosive vent, thermometer pocket on tank cover, Oil level gauge , Oil drain filter valve, Lifting lugs, Oil filling hole with cap , plug with connection plate complete. Air release valve plug and four Nos plain solid cast steel detachable rollers. (f) One No 100 mm dia dial type thermometer vapour pressure type , having range 0-120 Degree Celsius with metal guard having mazimum perimeter temperature reading indicator with re- setting devices (g) Two earthing terminal on tank cover to facilitate fixing of 25x4 mm GI iron earth strip for earthing of body (h) Rating plate and terminal marking plate (j) First filling of new transformer oil, conforming to IS- 335, filtered and tested. (l)Transformer shall be painted two coat of epoxy paint all as specified.

Supply , installed, testing and commissioning step down transformer, Copper wounded, Indoor type complete with standard fittings HT 11 KV/433 Volts (at no load) 3 phase 4 wire, 50 Hz, 400 KVA capacity core type double copper wound, oil immersed. oil cooled, delta connected on primary side (HV) and star connected on secondary side (LV) in accordance with vector group DYN-11 with natural brought out on secondry side (LV side) and having tapping at + 7.5% in step of + 2.5% on HV side to be changed by means of hand operated off load tap changer gear. Oil temperature should not exceed 40 degree celsius above ambient temperature and HV/LV winding temperature should not exceed 45 degree Celsius when measured by resistance method after continous full load run on an ambient temperature of 50 degree Celsius. The Transformer shall be IS- 1180, level II marked and shall comprises of the following :- (a) Three Nos porceian bushing suitable for 11 KV on HV side complete with copper rods, nuts and washers. (b) One cable box on LT side (Secondary side) consisting of four Nos porcelain bushing with copper rods, complete with nuts and washers with cable glands (c ) Oil conservator with filter type drain valve and oil level gauge (d) De- hydrating breather with first type fill of dehydrating agent (Silica Gel) (e) Explosive vent, thermometer pocket on tank cover .Oil level gauge , Oil dgain filter valve, Lifting lugs, Oil filling hole with cap , plug with connection plate complete. Air release valve plug and four Nos plain solid cast steel detachable rollers. (f) One No 100 mm dia dial type thermometer vapour pressure type , having range 0-120 Degree Celsius with metal guard having mazimum perimeter temperature reading indicator with re- setting devices (g) Two earthing terminal on tank cover to facilitate fixing of 25x4 mm GI iron earth strip for earthing of body (h) Rating plate and terminal marking plate (j) Extra bushing for neutral, out side the cable box for providing independent set of earthing for neutral. (k) First filling of new transformer oil, conforming to IS- 335, filtered and tested. (l)Transformer shall be painted two coat of epoxy paint all as specified.

Supply , installed, testing and commissioning step down transformer, Copper wounded, Indoor type complete with standard fittings HT 11 KV/433 Volts (at no load) 3 phase 4 wire, 50 Hz, 500 KVA capacity core type double copper wound, oil immersed. oil cooled, delta connected on primary side (HV) and star connected on secondary side (LV) in accordance with vector group DYN-11 with natural brought out on secondry side (LV side) and having tapping at + 7.5% in step of + 2.5% on HV side to be changed by means of hand operated off load tap changer gear. Oil temperature should not exceed 40 degree celsius above ambient temperature and HV/LV winding temperature should not exceed 45 degree Celsius when measured by resistance method after continous full load run on an ambient temperature of 50 degree Celsius. The Transformer shall be IS- 1180, level II marked and shall comprises of the following :- (a) Three Nos porceian bushing suitable for 11 KV on HV side complete with copper rods, nuts and washers. (b) One cable box on LT side (Secondary side) consisting of four Nos porcelain bushing with copper rods, complete with nuts and washers with cable glands (c ) Oil conservator with filter type drain valve and oil level gauge (d) De- hydrating breather with first type fill of dehydrating agent (Silica Gel) (e) Explosive vent, thermometer pocket on tank cover .Oil level gauge , Oil dgain filter valve, Lifting lugs, Oil filling hole with cap , plug with connection plate complete. Air release valve plug and four Nos plain solid cast steel detachable rollers. (f) One No 100 mm dia dial type thermometer vapour pressure type , having range 0-120 Degree Celsius with metal guard having mazimum perimeter temperature reading indicator with re- setting devices (g) Two earthing terminal on tank cover to facilitate fixing of 25x4 mm GI iron earth strip for earthing of body (h) Rating plate and terminal marking plate (j) Extra bushing for neutral, out side the cable box for providing independent set of earthing for neutral. (k) First filling of new transformer oil, conforming to IS- 335, filtered and tested. (l) Transformer shall be painted two coat of epoxy paint all as specified.

Supply , installed, testing and commissioning step down transformer, Copper wounded, Indoor type complete with standard fittings HT 11 KV/433 Volts (at no load) 3 phase 4 wire, 50 Hz, 630 KVA capacity core type double copper wound, oil immersed. oil cooled, delta connected on primary side (HV) and star connected on secondary side (LV) in accordance with vector group DYN-11 with natural brought out on secondry side (LV side) and having tapping at + 7.5% in step of + 2.5% on HV side to be changed by means of hand operated off load tap changer gear. Oil temperature should not exceed 40 degree celsius above ambient temperature and HV/LV winding temperature should not exceed 45 degree Celsius when measured by resistance method after continous full load run on an ambient temperature of 50 degree Celsies. The Transformer shall be IS- 1180, level II marked and shall comprises of the following :- (a) Three Nos porceian bushing suitable for 11 KV on HV side complete with copper rods, nuts and washers. (b) One cable box on LT side (Secondary side) consisting of four Nos porcelain bushing with copper rods, complete with nuts and washers with cable glands (c ) Oil conservator with filter type drain valve and oil level gauge (d) De- hydrating breather with first type fill of dehydrating agent (Silica Gel) (e) Explosive vent, thermometer pocket on tank cover .Oil level gauge , Oil dgain filter valve, Lifting lugs, Oil filling hole with cap , plug with connection plate complete. Air release valve plug and four Nos plain solid cast steel detachable rollers. (f) One No 100 mm dia dial type thermometer vapour pressure type , having range 0-120 Degree Celsius with metal guard having mazimum perimeter temperature reading indicator with re- setting devices (g) Two earthing terminal on tank cover to facilitate fixing of 25x4 mm GI iron earth strip for earthing of body (h) Rating plate and terminal marking plate (j) Extra bushing for neutral, out side the cable box for providing independent set of earthing for neutral. (k) First filling of new transformer oil, conforming to IS- 335, filtered and tested. (l) Transformer shall be painted two coat of epoxy paint all as specified.

M&L for Earthing complete with Galvanised MS earth plate electrode 600 x 600 x 6 mm buired directly in the ground vertically to depth not less than 3 Mtr below the ground level with the top edge of earth plate depth not less than 2.25 Mtr below the ground level connected to GI earth sprip of 32 mm x 6 mm size by means of bolts , nuts and washers protected by GI tubing light grade 40 mm dia upto Test point 20 mm dia medium grade watering pipe with funnel & wire mesh , PCC pit in PCC 1:2:4 using 20 mm graded crushed stone aggregates chamber 40 mm thick RCC cover slab (1:2:4) type B-1 using 20 mm graded crushed stone aggregates complete all as specified and shown in electrical plate No. 3 of SSR Part-1 including earth work in any type of soil , removal of surplus soil to distance not exceeding 50 m and deposting where directed and providing charcol dust &salt layers all around the earth plate upto 15 cm all as required specified & as directed by Engr-in-Charge. ( Note: Up to 7.5 Mtr of pipe of 40 mm dia and GI strip shall be deemed to be included in unit rate quoted by tenderer)

M&L for Earthing complete with copper earth plate electrode 300 x300 x 3.15 mm buired directly in the ground vertically to depth not less than 3 Mtr below the ground level with the top edge of earth plate depth not less than 2.25 Mtr below the ground level connected to GI earth sprip of 20 mm x 3 mm size by means of bolts , nuts and washers protected by GI tubing light grade 40 mm dia upto Test point 20 mm dia medium grade watering pipe with funnel & wire mesh , PCC pit in PCC 1:2:4 using 20 mm graded crushed stone aggregates chamber 40 mm thick RCC cover slab (1:2:4) type B-1 using 20 mm graded crushed stone aggregates complete all as specified and shown in electrical plate No. 3 of SSR Part-1 including earth work in any type of soil , removal of surplus soil to distance not exceeding 50 m and deposting where directed and providing charcol dust &salt layers all around the earth plate upto 15 cm all as required specified & as directed by Engr-in-Charge. Notes for srl item No. 13 & 14 1.The rates for earthing under items includes the cost of followings: (a) Earth electrode. "(b) Main earthing lead from earth electrode to test point upto 7.5 metre" "(c) Material and labour for connecting earth electrode and earthing lead as specified." (d) Adequate quantity of charcoal dust and common salt. e) All labour involved including testing of earth net work. (f) Excavation and earth work or drilling hole for electrode. (g) P.C.C. pit and C.I. cover (h) Funnel with watering pipe, wire mesh and copper lugs etc. as specified. (j) G.I. protection pipe of size ordered specified for protection of earthing lead from mechanical injury or tempering. (k) Test point and extra length of main earthing lead beyond 7.5 metres (l) Connecting lead from test point to main switch or switch board or equipment to be earthed. 2.On testing after completion if the desired earth resistance is not obtained the earthing will be re-done at no extra cost."

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, LT 1100 volts grade heavy duty with aluminium stranded conductor of cross section area 500 Sqmm 3.5 core complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, LT 1100 volts grade heavy duty with aluminium stranded conductor of cross section area 400 Sqmm 3.5 core complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, LT 1100 volts grade heavy duty with aluminium stranded conductor of cross section area 300 Sqmm 3.5 core complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, LT 1100 volts grade heavy duty with aluminium stranded conductor of cross section area 240 Sqmm 3.5 core complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, LT 1100 volts grade heavy duty with aluminium stranded conductor of cross section area 185 Sqmm 3.5 core complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, LT 1100 volts grade heavy duty with aluminium stranded conductor of cross section area 150 Sqmm 3.5 core complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, LT 1100 volts grade heavy duty with aluminium stranded conductor of cross section area 120 Sqmm 3.5 core complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, LT 1100 volts grade heavy duty with aluminium stranded conductor of cross section area 95 Sqmm 3.5 core complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, LT 1100 volts grade heavy duty with aluminium stranded conductor of cross section area 50 Sqmm 3.5 core complete all as specified and directed.

Excavation in trenches not exc. 1.5 m wide and n. exc. 1.5m depth for laying of pipe / cable / foundation of poles & stays in any type of soft /loose soil and getting out etc complete all as specified and directed.

Supplying and laying reinforced precast concrete cable cover, class LV, type-2 with peak, size 300mm x 180mm x 40mm laid dry flat all as specified and directed.

M&L for Sand cushioning for under ground cable provided with a layers of 8 mm high before laying cable and 15 mm thick after laying and stretching the cable all as specified and directed. (Running thickness shall be measured)

M&L for returning filling in including, spreading, leveling and well ramming in layers not exceeds 25 cm thick in any type of soil all as specified and directed.

M&L for removing excavated material to a distance not exceed 50 m and depositing where directed at a level n.exc 1.5 m above the starting point all as specified and directed.

Supply and fix MCCB 400 Amp with rupturing capacity 35/36 KA, four pole, 50 Hz, 415 Volts Adjustable type.

Supply and fix MCCB 250 Amp with rupturing capacity 35/36 KA, four pole, 50 Hz, 415 Volts Adjustable type.

Shifting of transformer of capacity 200 KVA and 160 KVA from SATCOM to IAC Bldg and CAME wksp to SO block including opening of LT & HT connection and re-connect the LT & HT cable/conductor at shifting site as per Engr-in-charge.

Supply, installation, commissioning and testing of submersible copper wounded motor with pump set, water lubricated and water cooled with stream line non return valve suitable to discharge not less than 900 LPM and not less than 163 mtr head directly coupled with and including squerrel cage induction motor of capacity not less than 60 HP capacity suitable for three phase 415 + 7.5% volts, 50 Hz AC supply. Note:- (1) Contractor shall take proper precautions while lifting out and removing pump set and motor bore well so as to avoid any damage to column pipe and submersible cable. All necessary T&P and equipments required for lifting out pump set etc shall be arranged by the contractor at his own cost. (2) The cost of lowering of pump set and motor is deemed to be included in the quotated rate for the same. (3) Make and model/size of the pump and motor shall be as approved by the GE on production of the catalogue/literature of manufacturer by the contractor. Pump and motor should be of same make. (4) Pump set to be lowered to the min depth approx 100 mtr or as directed. (5) The quoted rate by the contractor for the above item shall be deemed inclusive cost of assembling & connecting the submersible motor pump set to column pipe and making necessary connection and testing including reconnecting water supply line connections. (6) Old materials retrived from site shall be deposited to MES store yard by contractor.

Supply, installation, commissioning and testing of submersible copper wounded motor with pump set, water lubricated and water cooled with stream line non return valve suitable to discharge not less than 750 LPM and not less than 163 mtr head directly coupled with and including squerrel cage induction motor of capacity not less than 40 HP capacity suitable for three phase 415 + 7.5% volts, 50 Hz AC supply. "Note:- (1) Contractor shall take proper precautions while lifting out and removing pump set and motor bore well so as to avoid any damage to column pipe and submersible cable. All necessary T&P and equipments required for lifting out pump set etc shall be arranged by the contractor at his own cost. (2) The cost of lowering of pump set and motor is deemed to be included in the quotated rate for the same. " "(3) Make and model/size of the pump and motor shall be as approved by the GE on production of the catalogue/literature of manufacturer by the contractor. Pump and motor should be of same make. (4) Pump set to be lowered to the min depth approx 100 mtr or as directed. (5) The quoted rate by the contractor for the above item shall be deemed inclusive the cost of assembling & connecting the submersible motor pump set to column pipe and making necessary connection and testing including reconnecting water supply line connections. (6) Old material retrived from site shall be deposited to MES store yard by contractor."

Supply, installation, commissioning and testing of submersible copper wounded motor with pump set, water lubricated and water cooled with stream line non return valve suitable to discharge not less than 750 LPM and not less than 150 mtr head directly coupled with and including squerrel cage induction motor of capacity not less than 35 HP capacity suitable for three phase 415 + 7.5% volts, 50 Hz AC supply. "Note:- (1) Contractor shall take proper precautions while lifting out and removing pump set and motor bore well so as to avoid any damage to column pipe and submersible cable. All necessary T&P and equipments required for lifting out pump set etc shall be arranged by the contractor at his own cost. (2) The cost of lowering of pump set and motor is deemed to be included in the quotated rate for the same. " "(3) Make and model/size of the pump and motor shall be as approved by the GE on production of the catalogue/literature of manufacturer by the contractor. Pump and motor should be of same make. (4) Pump set to be lowered to the min depth approx 100 mtr or as directed. (5) The quotated rate by the contractor for the above item shall deemed to be include the cost of assembling & connecting the submersible motor pump set to column pipe and making necessary connection and testing including reconnecting water supply line connections. (6) Old/BER retrive mterail from site to be deposited to MES store yard by contractor.

Supply only MS water tubing as in column pipe, 100 mm bore medium grade of thickness 4.5 mm, ISI marked, conforming to relevant IS for column pipe in required length but length not more than 3.00 mtr, both end flanged 8 mm thick flanged internally threaded and duly welded with pipe using 4 Nos MS strip of size 20x3 mm in triangular right angled shape with provision of 04 Nos holes and side slot for passing submersible cable on both flanged end, including painting with two coats of anti corrosive bituminous paint over a coat of red oxide primer complete all as specified and directed by GE.

Supply and fix multi cavity water sanitiser/conditioning station with proportional dosing arrangements at zero discharge of the power free automatic system 100 ltr tank, cavities are complete with lids with overflow valve, water inlet valve, outlet valve (for offline automated gravity flow), drain valve, PVC pipe etc alongwith set of 25 pcs chlorine tablets contained in plastic cylindrical sealed disposable sanitizer refill for disinfaction of drinking water with arrangement for controlled release of disinfectant in water suitable for operation through for recommended dosing system make and design as approved by GE before execution of work. Note:- (a) Replacement indication- visual & weight variation (b) Water contact orifice design sealed when dry exposed upon.

M&L for earthing complete with GI earth plate electrode of size 60cmX60cmX6 mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides by 15 cm thick and packed layer of charcoal dust and common salt filling in alternate layers etc and connected to and including GI strip of size 32x6 mm mm dia up to 7.5 mtr by means of bolts, nuts, check nuts and washers made of brass and protected by light grade 20mm dia upto 2.7 mtr long GI pipe connected to main control board and GI pipe light grade 20mm bore for watering and including funnel, wire mesh, RCC pit cover 50mm thick and PCC chamber pit with PCC 1:2:4 type C2 (including excavation and earth work disposal of surplus soil to a distance not exceeding 50 metre) and testing after completion all as specified complete. Notes for srl item No. 37 1.The rates for earthing under items includes the cost of followings: (a) Earth electrode. "(b) Main earthing lead from earth electrode to test point upto 7.5 metre" "(c) Material and labour for connecting earth electrode and earthing lead as specified." (d) Adequate quantity of charcoal dust and common salt. e) All labour involved including testing of earth net work. (f) Excavation and earth work or drilling hole for electrode. (g) P.C.C. pit and C.I. cover (h) Funnel with watering pipe, wire mesh and copper lugs etc. as specified. (j) G.I. protection pipe of size ordered specified for protection of earthing lead from mechanical injury or tempering. (k) Test point and extra length of main earthing lead beyond 7.5 metres (l) Connecting lead from test point to main switch or switch board or equipment to be earthed. 2.On testing after completion if the desired earth resistance is not obtained the earthing will be re-done at no extra cost."

Supply, installation, testing and commissioning of Water cooler fully stainless steel, electric driven single phase 230 Volts 50 Hz having approx storage capacity and nominal cooling capacity 80/40 litre including necessary connection conforming to IS : 1475 (part-1) :2001, complete all a s specified and directed.

Supply, installation, testing and commissioning of Water cooler fully stainless steel, electric driven single phase 230 Volts 50 Hz having approx storage capacity and nominal cooling capacity 120/60 litre including necessary connection conforming to IS : 1475 (part-1) :2001, complete all as specified and directed.

Supply, installation, testing and commissioning of Water cooler fully stainless steel, electric driven single phase 230 Volts 50 Hz having approx storage capacity and nominal cooling capacity 150/150 litre including necessary connection conforming to IS : 1475 (part-1) :2001, complete all as specified and directed.

Supply, installation, testing and commissioning of hot and cold hi wall split units air conditioner (indoor/outdoor) copper condensor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality, electrical driven, single phase with minimum 3 star rating and EER 3.2 of capacity 1.5 ton including necessary connection, stablizer free operation complete with PVC drain pipe of suitable dia, copper piping with insulation of suitable size from indoor unit to outdoor unit as per manufacturer's instruction, one pair of Mild Steel powder coated heavy duty standard bracket/stand including necessary dast fasterner and copper wire of size 2.5 sqmm 4 core PVC insulated unarmoured 1100 Voltall as specified and directed.

Supply, installation, testing and commissioning of hot and cold hi wall split units air conditioner (indoor/outdoor) copper condensor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality, electrical driven, single phase with minimum 3 star rating and EER 3.2 of capacity 2.0 ton including necessary connection, stablizer free operation complete with PVC drain pipe of suitable dia, copper piping with insulation of suitable size from indoor unit to outdoor unit as per manufacturer's instruction, one pair of Mild Steel powder coated heavy duty standard bracket/stand including necessary dast fasterner and copper wire of size 2.5 sqmm 4 core PVC insulated unarmoured 1100 Volt all as specified and directed.

Supply and fix voltage stabilizer for automatic operation copper wound, single phase naturally air cooled indoor type & designed for input variation between 160 to 250V with output valtage stabilized at 230 V with accuracy of ± 2.5% and of capacity 1.0 KVA conforming to IS:8448:1989 updated as on date complete all as specified and directed.

Supply and fix voltage stabilizer for automatic operation copper wound, single phase naturally air cooled indoor type & designed for input variation between 160 to 250V with output valtage stabilized at 230 V with accuracy of ± 2.5% and of capacity 2.0 KVA conforming to IS:8448:1989 updated as on date complete all as specified and directed.

SAGGI ELECTRIC COMPANY

N K BUILDERS

BRITE INDUSTRIES

Vijaypower Generators Limited

M P TYAGI ENGINEERS AND CONTRACTORS

Choice india

M K ENGINEERS CO.