Providing and Fixing to LED Street Fittings of Main Gate to Left Side Security Cabin at Juj Dam.

Name of work:- Providing and Erecting to LED Street Light Fittings of Main Gate to Left Side Security Cabin at Juj Dam

Qty Description Item Rate Per Amount

Replacing Old and u/s by Supplying and erecting Flexible PVC

Rupees FourtySix Paise

1 520.00 insulated multi strand multi core 1.1 kv grade ISI marked copper 46.46 Mtr.

wires of following size to be erected as directed. FourtySix Only

(e) 1.50 Sq.mm 3 core round PVC sheathed

Replacing Old and u/s bySupplying and erecting LED street light

/ Flood light fittings with High power White LEDs wattage of

Watt and above assembled on single MCPCB, efficiency more

than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat

sink extruded aluminium with diffuser and Polycarbonate optics/

lenses, with toughened glass with company mark/name

2 engraved or embossed 160 to 270 V,Power Factor more than

0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio

>0.45, Luminaire efficacy> 100 lumens/watt . LED driver

efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and

Rupees Five Thousand

,Light must have 440VAC line supply with over-voltage

70 5976.17 Nine Hundred SeventySix Ea.

Paise Seventeen Only

(ii) above 48 to 60 Watts Cat-lll

Replacing Old and u/s by providing and erecting Miniature

circuit breaker single pole 6A to 25A suitable to operate on

V A.C. system and having breaking capacity 10 KA to be Rupees One Hundred

erected in existing box. confirming to IS 8828/1996 with ISI Mark Twelve Paise Eleven Only

Replacing Old and u/s by Providing & erecting 415 V MCB Four

Rupees Seven Hundred

Pole for Motor & Inductive Load (C Curve) having 10KA

4 1 737.30 ThirtySeven Paise Thirty Ea.

breaking capacity & confirms to IS :8828 in existing box having

following capacity

(c)63 Amp. cat- iii

Replacing Old and u/s by Providing and erecting XLPE

(IS:7098)(I)-88 ISI armoured cable multistrand Aluminium Rupees One Hundred

5 760.00 conductor for 1.1 KV. to be laid on wall with necessary clamps 153.52 FiftyThree Paise FiftyTwo Mtr

or in existing trench / pipe of following size of cables Only

(A) 4 core 16 Sq. mm

Making trench in soft soil of suitable width of 90 cm deep for

Rupees FiftyFive Paise

6 410.00 laying cable or locating the fault all over the run and back filling 55.55 Mtr

the same and making the surface as normal ground. FiftyFive Only

Making trench in Hard Murrum / Tar Road of suitable width of

cm or required depth for laying any size of cable or locating the Rupees SeventyFour

7 275.00 fault all over the run and back filling the same and making the 74.74

Paise SeventyFour Only

surface as normal ground.

Replacing Old and u/s by Providing & laying approved make

Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary Rupees SixtyTwo Paise

connecting accessories of same material at required depth in SixtyTwo Only

existing trench for laying of cable. below ground / road surface

for enclosing cable

(A)50 mm outer dia

Replacing Old and u/s by Providing & laying approved make

Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary Rupees Fifteen Paise

9 288 connecting accessories of same material at required depth in 15.15 Ea.

existing trench for laying of cable. below ground / road surface

for enclosing cable

Replacing Old and u/s by Supplying and erecting approved

make Octagonal pole made from HR sheet steel. The pole

should be made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable suspend local

wind speed with integral Junction box consist of terminal plate of

10 min 6mm Hylam sheet, standard profile 35mmX7.5mm Din-Rail

for MCB Mounting, stud type terminal and arrangement for cable

termination to be erected With Suitable foundation (Included)

as per details given by manufacturer considering site

(D) 6 Mtr. Long 70 mm Top X 135 mm bottom dia, 3 mm

thickness with 200mmX200mmX12mm base plate, 4-M20 Bolts Rupees Eight Thousand

35 and 600mm long with necessary G.I. J Bolts .Approx Pole 8192.11 One Hundred NinetyTwo Nos.

weight 59 kg Paise Eleven Only

Replacing Old and u/s by Supplying and erecting Street light

pole bracket comprising main B Class GI pipe of 4.2 cm/require

outside dia. complete with suitable B Class G.I. sleeve tubing of

approx. 45cms.length and suitable for 76.5mm/80mm/require

size of pole top having nuts and bolts for fixing the brackets and Rupees Six Hundred

11 35 having spread of 0.5 mtr. Length with 110 deg.with vertical 622.16 TwentyTwo Paise Sixteen Nos.

plane and suitable welded stiffener reducer and nipple with Only

check nut complete painted with one coat.of Red oxide / PU

base primer and two coats of Aluminium / PU paint. paint with

following nos of arms.

[B] Double Arm Bracket 0.5 Mtr

Replacing Old and u/s by Supplying & erecting approved make

IP 55 grade Company fabricated Timer Panel of following

capacity for switch On-Off street lights on time scheduling basis

made from 16G CRCA sheet duly epoxy power painted inside

and outside with hinged doors and locking arrangement Rupees Seventeen

12 1 consisting of suitable size of 4 Pole MCB and 4 pole contactor 17059.91 Thousand FiftyNine Paise Ea.

(cat-III)with analog time switch, auto manual switch of same NinetyOne Only

make and suitable input and output Bakelite terminals and with

door earthing approved by Engineer in charge.

(C) 63 Amp 1% LC

Supplying & erecting earth pit of minimum bore dia.150mm size

approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 50mm having 80-

200 Micron galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive

compound with high charge dissipation suitable for following

type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including Rupees Four Thousand

13 5 value of earth resistance of installation duly stamped and signed 4591.46 Five Hundred NinetyOne Ea.

by agency and officer Incharge has to ensure the value of Paise FourtySix Only

earthing resistane mentioned in test Certificate) & having back

filling compound of (B) Inner chemical (CCM Compound)-

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing compound should be

capable to retain moisture for long time Necessary test report

must be submitted by Agency.

(a) For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting HOT deep Galvanised iron strip wire 8 to Rupees SeventySeven

Paise SeventySeven Only

I/We am/are willing to carry out the work at ……………………………………………% above/below percent (shouldbe written in figured and

words) of the estimated rates mentioned above. Amount of my/our tender works out as under.

Estimated amount Estimated amount

Put to tender Rs______________ Put to tender Rs______________

Deduct : ___________ % Above RS__________ Deduct : ___________ % Below RS__________

*(Please strike out whitchever is not applicable).

Note 1 – All work shall be carried out as per public works department handbook and other specification of Division ot as directed.

Note 2 – All the columns is schedule should be filled in ink and the total of the entries in the last column should be struck by the

contractor under his signature.

Note 3 – Rates quoted include clearance of site (prior commencement of work and at its close ) in all respects and hold good for work

under all conditions, site, moisture,weather etc.

Note 4 – To be continued on additional sheets, if found necessary.

Note 5 - The rates quoted by the Contractor must be inclusive of all taxes prevailing on due date of bid submission except GST. However,

any subsequent changes in the tax structure by Government after due date of bid submission will be compensated (+/-) on availability or

submission of actual documentation. Contractor will have to intimate Engineer regarding changes occurred in the tax structure after bid

submission. If the contractor fails to provide such information and if any financial obligation may arise due to change in tax structure,

same will be recovered from the contractor. GST will be paid separately on the bills. Hence, it is the responsibility of the contractor to pay

the GST to the concerned Authority.

Deputy Executive Engineer Executive Engineer

Electrical Sub Division Ukai Division No