Civil works for the construction of sewage treatment plant

Amount

Construction of Treatment Plant Units

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap). 500 mm dia piles. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Vertical load testing of piles in accordance with IS 2911( Part IV) including installation of loading platform and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of engineer -in-Charge.Single pile upto 50 tonne capacity.Routine test. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed: All Kinds of soil. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed. All kinds of soil. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m to 3 m, disposed earth to be levelled and neatly dressed. All kinds of soil. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 3 m to 4.5 m, disposed earth to be levelled and neatly dressed. All kinds of soil. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete (Measurements to be taken of the face area timbered). Depth not exceeding 1.5m. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete (Measurements to be taken of the face area timbered).Depth exceeding 1.5 m but not exceeding 3 m. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Close timbering in trenches including strutting, shoring and packing cavities (wherever required) complete (Measurements to be taken of the face area timbered).Depth exceeding 3 m but not exceeding 4.5m. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Bailing out water Using 5HP Pump- Bailing out water with 5HP engine and pump set including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:3:6 (1 cement:3 coarse sand:6 graded stone aggregate 20 mm nominal size). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S (non modular) bricks of class designation 7.5. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Centering and shuttering including strutting, etc. and removal of form for: Foundations,footings,bases of coumnns,etc or mass concrete. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Centering and shuttering including strutting, etc. and removal of form for: Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level: 1:1.5:3 (1 cement:1.5 coarse sand:3 graded stone aggregate 20 mm nominal size). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing, hoisting and fixing up to floor five level precast reinforced cement concrete in shelves including setting in cement mortar 1:3 ( 1 cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (Zone - III) : 3 graded stone aggregate 20 mm nominal size). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanicaly Treated bars of grade Fe-500D or more. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and injecting approved grout in proportion recommended by the manufacturer into cracks/honey-comb area of concrete/masonry by suitablegun/pump at required pressure including cutting of nipples after curing etc.complete as per directions of Engineer-in-Charge. (The payment shall be made on the basis of actual weight of approved grout injected.) Stirrer mixed SBR Polymer (of approved make) modified Cement slurry made with Shrinkage Compensating Cement in concrete/RCC work. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

2 mm cement plaster finished with a floating coat of neat cement of mix: 1:3 (1 cement: 3 fine sand). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

12 mm cement plaster of mix:1:4 (cement:4 coarse sand). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing in position Pre-cast R.C.C. manhole cover and frame of required shape and approved quality.LD-2.5, Rectangular shape 600x450 mm internal dimensions. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete: Serrated with central bulb(225mm wide,8-11 mm thick). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Drilling holes in RCC wall / slab etc for providing and fixing PVC pipe in between trenches. Job includes labour charges, hire charges for core cutting machines, transporting to site and making the holes in. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Supplying, providing and fixing FRP cover 1100mmx1100mm size, 10mm thick with lock for screen chamber. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer. M.S.tube. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Applying 2 component epoxy coating Dr.Fixit Epoxy,VOC free,100% solids seamless brush/roller applied water proof coating system (Dr.Fixit) approved as per UE305/2011 for contact with water,with tensile strength of 6-8 Mpa and eongation>100% temperature resistance between 40 degC to 80 deg.C,The application includes priming the surfacewith PU/Epoxy based primer and applying in 2 coats through rolller/brush at 1.5kg/sqm. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Construction of Operators cum store room

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement:3coarse sand:6 stone aggregate 20 mm nominal size). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6(1 cement:6 coarse sand). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Centering and shuttering including strutting, etc. and removal of form for: Lintels,beams,plinth beams,girders bressumers and cantilevers. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Centering and shuttering including strutting, etc. and removal of form for: Suspended floors,roofs,landings,balconies and access platform. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3 ( 1 cement:1.5 coarse sand:3 graded stone aggregate 20 mm nominal size). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanicay Treated bars of grade Fe-500D or more. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

12 mm cement plaster of mix:1:4 (1 cement:4 fine sand). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

6 mm cement plaster of mix:1:3 (1 cement:3 fine sand). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately) :Flat surfaces. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portion,Powder coated aluminium(minium thickness of powder coating 50 micron). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminum (minimum thickness of powder coating 50 micron). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Supplying godrej make 6 lever pad locksincluding 3 nos key all as per manufacture and direction by engineer-in-charge. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angles 40x40x6 mm for diagonal braces. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by weiding. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with :4.0 mm thick glass panes. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing angle iron frames for doors, windows and ventilators of mildsteel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall withdash fastener, including fixing of necessary butt hinges and screws and applying apriming coat of approved steel primer, all complete as per the direction of Engineer In charge. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.20 mm M.S laths with 1.20 mm thick top cover. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing ball bearing for rolling shutters. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coated applied @1.67ltr/10sqm over and including priming coat of exterior primer applied @2.20 kg/10 sqm). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10 Kgf/cm2- External work - Exposed on wall. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge 20 mm dia 10 Kgf/cm2- Internal work - Exposed on wall. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate)finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Cement plaster askirting upto 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement .18 mm thick. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Extra for making chequers of approved pattern on cement concrete floors, steps, landing, pavements etc. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and placing on terrace (at all floor levels) PVC water storage tank, ISI marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes with. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing uplasticised PVC connection pipe with brass unions:45 cm length 15mm nominal bore. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete:15 mm nominal bore. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Supply and providing particle board make office table with drawer of size 1200x600x750mm including cost of all materias,cinveyance,GST etc. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Supply and providing pastic office chair Nilkama,Chairman or any approved item icuding cost,conveyance,GST etc complete. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Floor painting with floor enamel paint of approved brand and manufacture of required colour to give an even shade: Two or more on new work. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Item Shifted to Sub head 14 as item 14.73 Item Shifted to head 14 as item 14.74 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads,landings etc. of stair cases, including use of chequered plate wherever required, all complete. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total coated thickness, zinc coating 120 grams per sqm as per IS:mm(+0.05%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws complete:Ridges plain (500-600 mm). The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Waste Water Conveyance Arrangements

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:Pipes,cables etc.exceeding 80 mm dia but not exceeding 300 mm dia. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Constructing masonry chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I surface box 350x350 mm top and 165 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 grades stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design:With common burnt clay F.P.S (non modular) bricks of class designation 7.5. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing PVC pipes includings jointing of pipes with one step pvc solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm dia 6 Kgf/cm2. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 50 mm dia 6 Kgf/cm2. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. 63 mm dia 6Kgf/cm2. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm dia 6 Kgf/ cm2. The rate inclusive of all material charge, labour, transportation, scaffolding (if needed) loading / unloading at the work space etc complete as per the direction of engineer in chrge.

RUBICON PROJECT MANAGEMENT P LTD

TELCON Infrastructures

U.R.RAJEEV

BREC PROJECTS PRIVATE LIMITED