WBPWD/EE/PED/NIQ05 /2024-2025

Amount

Supply Installation, testing & Commissioning of floor-cum-wall mounted cubical of 1200x1350x300 mm type self supporting compartmentalized with separate bus & cable alleys made of 3mm thick CRCA sheet & angle iron having size of 40x40x5 mm frame supported incl. necy. interconnection by suitable size & grade copper cable / solid link/ flat bar of 25x5 mm incl. painting the panel board by powder coated paint as per direction of E.I.C and S & F of the following.

Incoming: 415V, 160A TPN SFU open execution in existing SS enclosure/cubical with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating.-01 No. ( Make - L& T, )

Incoming: 415V, 125A TPN on load front operated Changeover switch open execution type in SS enclosure/cubical with nuts bolts etc.-01 No. ( Make - L& T, )

Busbar:- 415v, 200 A four BAR CU bus bar [4 x 50 mm x 6mm]- 0.8 mtr length with heat shirnk PVC colour tube insulated with DMC bus support - 1 set

Out going :1. 415V, 100A TPN SFU open execution in existing SS enclosure/cubical with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating -1 nos, ( Make - L&T )

2. 415V, 63A TPN SFU open execution in existing SS enclosure/cubical with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating-3 Nos, ( Make - L&T,)

3. 3415V, 32A TPN SFU open execution in existing SS enclosure/cubical with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating-1 No ( Make - L& T,)

(iii) CT 160/5A ratio -3 Nos [Kappa]

(iv)2A SPMCB (C-curve, 10KA)-3Nos [L&T/LEGRAND/SIEMENS]

(v) LED type indicating lamp (Red, Yellow & Blue colour)-3 Nos [L&T/LEGRAND/SIEMENS]

(vi) Danger Notice Board (8" x 12")-1 No

Supplying and fixing 415V, 200 A TPN SFU with sheet steel enclosure on angle iron frame on wall with nuts bolts etc incl. S & F 3 nos. DIN type HRC fuse as per rating. (Make- L&T/ Havells/ Seimens/ABB)[D-1/1(b)]

Supplying and fixing double door Horizontal TPN MCB Distribution board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment [D-10/14] 4 way ((Make- Legrand /L&T/ Havells/ Seimens/ABB)

Supplying and fixing double-door SPN MCB Distribution Board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attachment. [D-9/13] 2+8 way (Make-Legrand/L&T/ Seimens/ABB)

Supplying and fixing 240/415 V MCB Isolator on din rail of existing DBs and necessary connection.63 A FP ( For TPNDB Incoming) [D-5/6](Make- Legrand/L&T/Seimens/ABB)

40 A DP Isolator( for SPNDB Incoming) [D-5/6](Make- Legrand/Seimens/Havells)

Supplying and fixing 240/415 V MCB of Breaking capacity 10kA & C characteristics on din rail of existing DBs and necessary connection 6-32 SPMCB [D-6/7](Make- Legrand/Seimens/Havells)

Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) partly in 20mm size PVC rigid conduit 'FR' (Precision make) [for ceiling portion only] and in 19mm bore, 3mm thick polythene pipe [for horizontal & vertical run embedded in wall], with 1x22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Modular type switch (Brand approved by EIC) fixed on Modular GI switch board complete with 2 no. suitable size “Ph & N” copper bar with top cover plate making earthing attachment fixed on wall incl. mending good damages to original finish. [only PVC Rigid Conduit on ceiling and remaining portion concealed] ] Average run 8 mtr [E-25/4]

Distribution wiring in 1.1 KV grade 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire (Brand approved by EIC) in 20mm size PVC rigid conduit 'FR' (Precision make), with 1.1 KV grade 1 x 22/0.3 (1.5 sqmm) single core stranded 'FR' PVC insulated & unsheathed copper wire as ECC, to 6A 3 pin Modular type plug socket & switch (Brand approved by EIC) on 4 Module GI switch board with 3/4 Module top cover plate on wall incl. necy. connection making earthing attachment, painting and mending good damages to building works.[E-24]

On Board [E-24/3(a)]

Supply & Fixing 240 V, 4 nos. 6 A, 3 pin Modular type plug socket with 4 nos. 6A Modular type switch (Brand approved by EIC), 16A Modular switch type MCB (C-Curve) and Indicator without plug top on 2 row 18 Module GI Modular type switch board with 2 row 18 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc.[E-18/12]

Supply & Fixing 240 V, 25 A, 3 pin Modular type plug socket (Brand approved by EIC), without plug top and switch with 2 Module GI Modular type switch board with top cover plate flushed in wall and making necy. connections with PVC Cu wire and earth continuity wire etc. [E-17/5(a)][ for AC and UPS]

Supply & Fixing 240 V,25 A, 3 pin Modular type plug top with indicator (Brand approved by EIC) & necy. Connections. [E-17/5(b)]

Supply & Fixing 240 V, 25 A, Modular type starter (Brand approved by EIC) with 25A Modular switch type DP MCB (CCurve) and 4 Module GI Modular type switch board with 4 Module top cover plate flushed in wall incl. S&F switch board and cover plate and making necy. connections with PVC Cu wire and earth continuity wire etc. [E-19/17]

Supply & Fixing 240V, Modular Socket (2 Module) type fan regulator (Step type) (Brand approved by EIC) on existing Modular GI switch board with top cover plate incl. making necy. connections etc. [E-18/10]

Supplying & Fixing 240 V AC/DC superior type Ding-Dong Call Bell (Anchor) on HW board incl. S&F HW board [D-13/20(a)]

Supplying and Drawing 1.1 KV single core stranded 'FR'PVC insulated & unsheathed single core stranded copper wire (Brand approved by EIC) of the following sizes in the prelaid polythene pipe and by the prelaid GI fish wire and making necy. connection as required .3x1.5 sqmm [E-9/1(a)][Make- Gloster/ Finolex/ Polycab/RR Kable/Havells]

2x36/0.3 (2.5 sqmm) + 1x22/0.3 (1.5 sqmm) as ECC [E-9/1(s)]

2x56/0.3 (4 sqmm) + 1x36/0.3 (2.5 sqmm) as ECC [E-9/1(v)]

2x84/0.3 (6 sqmm) + 1x56/0.3 (4 sqmm) as ECC [E-9/1(y)]

Cutting Channel of size (40 mm x 40 mm) on masonry wall by Electric operated cutting machine incl. supplying & fixing heavy gauge 19 mm, 3 mm thick Polythene pipe by means of anchoring chemical (Hilti/Sika) and GI 'U' hooks of 8 SWG incl. supplying and drawing 18 SWG GI wire as Fish wire and mending good damages to original finish by using own tools and tackles 19 mm dia 3 mm thick polythene pipe without earth continuity wire.[E-3/6] [E-3/6(a)]

Supplying and fixing polythene pipe complete with fittings as necy. under ceiling/beam, bound with 22 SWG GI binding wire incl. supplying and drawing 1x18 SWG GI Wire as fish wire inside the pipes and fittings and providing 50 mm dia disc of MS sheet (20 SWG) having colour paint at one face fastened at the load point end of the polythene pipe with fish wire (synchronizing with roof/beam casting work of building construction) [E-2/1]19mm dia 3mm thick Polythene Pipe [E-2/1(b)]

25 mm dia 3mm thick Polythene Pipe [E-2/1(c)]

Supplying and fixing PVC Rigid Conduit 'FR' [Precision Make] on wall, ceiling with saddles and other accessories as required and mending good damages to building works [E-16/7]20mm size [E-16/7(a)]

Supply of 4 Core 25 sqmm XLPE Insulated & Sheathed Armoured Aluminium Conductor cables for Working Voltage up to 1100 Volts of following sizes [ Make:- Gloster/ Nicco/KEI/Polycab/ Havells][Gloster Feb, 2023] 4 core 25 sqmm

Supply of 2 Core 6 sqmm XLPE Insulated & Sheathed Armoured Aluminium Conductor cables for Working Voltage up to 1100 Volts of following sizes [ Make:- Gloster/ Nicco/KEI/Polycab/ Havells][Gloster Feb, 2023] 2 core 6 sqmm [for campus light]

Laying of one No. cable upto 35 sqmm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed [F-2/1(a)]

Laying of cable upto 2 core 25 sqmm on wall/surface incl. S & F MS saddles with earthing attachment in 10 SWG GI (Hot Dip) Wire, making holes etc. as necy. mending good damages and painting as per GS.[F-1/2(a) ]

Laying of cable as below, after cutting floor/pavement/wall/ and making holes incl., embedding the cable at an average depth as below and mending good the damages to original finish incl. removing the rubbish From 2.5 sqmm to 35 sqmm at an average depth of 75 mm in floor/pavement/wall etc. [F-3/5(i)]

Supplying and fixing compression type gland and finishing those for following XLPE / PVC armoured cable (2/4 / 3.5)Core as per GS. 2 core 6 sqmm [F-4/7(a) & F-5/8(b-ii)]

4 Core 25 Sqmm [[F-5/8(b)(xiii)+ [F-4/7(c)]

Supply of BLDC type 1200 mm ceiling fans complete with all accessories with remote. ( Make - Crompton Model--1200 mm ENERGION HS (Remote)-35 W , 5 star)or equivalent model of Usha/Havells as approved by EIC) . [NS]

Supplying & Fixing MS fan clamp of two piece type for RCC as per approved specification as per GS. [ D-14/29 ]

Fixing only ceiling fan complete with blades, canopy, fork, rubber bush etc as per GS. [C-3/21(a)]

S & Delivery of single 4 ft., 22 watt LED light fitting complete with all accessories with tube lamps as follows:[Make -Philips cat no. TMC 502 P1 x T- LED 22 W P3241 including MAS LED TUBE 1200mm 18W 865 T 8 I- 2100lm ] or eqiv, make of Bajaj/ Crompton/Havells as per choice of EIC.[NS]

S & Delivery of double 4 ft., 22 watt LED light fitting complete with all accessories with tube lamps as follows:[Make -Philips cat no. TMC 502 P2 x T- LED 22 W P3241 including MAS LED TUBE 1200mm 18W 865 T 8 I- 2100lm ] or eqiv, make of Bajaj/ Crompton/Havells as per choice of EIC.[NS]

.Fixing only single/twin LED Batten light fitting complete with all accessories Directly on wall/ceiling as per GS[ C-2/14(d) ]

Supply & Fixing angular batten holder (Anchor) on 75mm dia PVCround block / round bakelite on wall/ceiling as per GS. [ D-13/22 ]

Supply and fixing 9W LED bulb (Bajaj/CG/Philips/wipro /Havells) on existing batten holder[NS]

Supply & fixing heavy duty Exhaust fan(Make-EPC or equivalent make as approved by E.I.C] of followinng sizes after making hole in wall and making good damages and smooth cement finish etc. as practicable as possible and providing necy. length of PVC insulated wire and making connection for exhaust as per G.S. .[EPC, January, 2022]

9"( 230mm ) Speed 1370 RPM [NS]

Supply & Fixing louver shutter on wall with necy. bolts & nuts (6 mm dia x 62 mm long) [D-14/32] (9")

Fixing only outdoor / street light type fluorescent light fitting or MV light fitting complete with all accessories to be fixed /projected from the wall of the building incl. making holes/providing clamping arrangement & necy. GI reducer as required. S&F 40 mm GI pipe (ISI-Medium) quality 1.5 mts. average length having suitable bend S&F necy. length of 1.5 sqmm PVC insulated single core stranded annealed copper wire and making connections as required and mending good damages to wall incl. painting etc. [C-3/18]

Supply & Fixing of 240V, 50 W LED flood light luminarie complete with all accessories and equipped with IP66 Protection (Make- Crompton Greaves-Cat no.- TFS-504-50-57-NL-SL-GL-NBK or equivalent make of Bajaj/ Havells/Philips/wipro/other equivalent make as approved by E.I.C) on existing MS Pipe/Mini Pole as per direction of E.I.C[NS] [ Crompton, Price list of January 2023]

Supply & Fixing of 240V, 50 W LED Street light luminarie complete with all accessories and equipped with IP66 Protection (Make- Crompton Greaves-Cat no.- CRP-409-60-57-SL-GL-NSG or equivalent make of Bajaj/ Havells/Philips/wipro/other equivalent make as approved by E.I.C) on existing MS Pipe/Mini Pole as per direction of E.I.C[NS] [ Crompton, Price list of January 2023]

S/F G. I. water proof looping cable box of size 200x150x100mm having hinged top Cover with rubber gasket lining, railway type mechanical locking anangement, earthing terminal with lug etc. of the following sizes as indicated below, Comprising of one 250 V, 15 A Kit-Kat fuse unit, one NL on porcelain insulator etc. and housing the same on pole above 5ft from ground level by necessary pole clamp . [I-2/16(a)]

S&F of 250V timer DB (equivalent to 8 way SPNDB in size) with double door sheet steel enclosure, neutral bar, din rail, with lP43 protection comprises with 20/25A DPMCB(C-curve 10ka) and 1 no 24 hr analog time switch and 1 no 18/25A power contactor complete with internal wiring with suitable size of copper wire including 1 no toggle switch and LED indicator and earthing attachment as per direction of EIC [NS]

S & F of MF 1 Starter (Make-L&T, ) starter on angle iron frame as to GS.[NS]

Earthing with 50 mm dia GI pipe 3.64 mm thick x 3.04 Mts. long and 1 x 4 SWG GI (Hot Dip) wire (4 Mts. long), 13 mm dia x 80 mm long GI bolts, double nuts, double washers incl. S & F 15 mm dia GI pipe protection (1 Mts. long) to be filled with bitumen partly under the ground level and partly above ground level driven to an average depth of 3.65 Mts. below the ground level as below By TATA-M GI pipe.[G-1/2(a)]

Excavation of soil for installation of Earth Electrode and filling & ramming. (For Morum Soil) [G-1/1(a)]

Extra of treatment of soil by using salt & charcoal for pipe electrode. [G-2/3(b)]

Connecting the equipments to earth busbar including S & F Solid GI (Hot Dip) wire of size as below as per GS No.-4 SWG [G-2/5(a)(i)]

supply and installation of Home UPS , Capacity 2 KVA, 24 Volt operated and output 230V 50HZ . Internal or external 1 KV surge protection device should be fitted. (Make EXIDE / Luminous / Sukam / Microtech (24 months warranty).

Supply and installation of EXIDE, INVATUBULAR batter, 12 Volt, 180 AH including necessary interconnection Model No: IT - 500+ (42 Months warranty).

Supply and installation of MS angle battery rack for keeping 2 nos battery and inverter on the top.

Supply & Fixing of IP 65 Rated 10 watt bollard light (Syrus) robust design and efficent light distribution.[Make-Crompton , LBLSR-10-WW/Phillips/Wipro/Magic/Simoco)

Supply & installation of MS Structure mounted rectengular type Metal Sign Board of stainless steel high glossy anodized lettering to be fixed by supply & fixing Alumium Composit Panel (ACP) 3.5mm thick base with steel letter identification board to be fixed on piller/wall at entrance gate/entrance of building of size 17ft X 7ft X 10 inch.

Metal Signage Board-1 at Main Gate or Roof Top

A. The total structure to be fabricated by 50X50X6mm MS Angle complete with 20SWG GI sheet on the back side of the structure as directed by EIC. The board will be fixed on a pre errected MS structure made by U-Chanel, Angle & 50X5 MS Flat incl. fixing 4 nos 50W LED flood light (Make- Crompton Geaves, Cat no.- CFS-504-CFS-504-50-57-60D-SL-GL-NSG or equivalent make of Havells/Philips/Bajaj//wipro/other equivalent make as approved by E.I.C) using 1.5m arm of holo bar of size 30x30x2mm

B. The high glossy lettering & National Emblem have to be fixed on ACP board over front fascia with 40mmX40mmX22SWG stainless steel angle with ss screw on each side of board structure. The Board (Individually hollow pipe & back cover) to be painted by two coats synthetic enamel paint over a coat of primer. The quality of letter is 22SWG 304 Grade. National Emblem should be fixed on the top of the board and lettering in English language to be fixed just below of it as per direction of EIC.

C. National Emblem at top

Biswabangla logo [approve by EIC]

GOVERNMENT OF WEST BENGAL DEPARTMENT OF FINANCE ( REVENUE) DIRECTORATE OF REGISTRATION AND STAMP REVENUE, WEST BENGAL OFFICE OF THE ADDITIONAL DISTRICT SUB-REGISTRAR BALARAMPUR P.O.- Rangadih, P.S- Balarampur, Dist- Purulia, PIN-723143

D. Letter size (approx.)

(i) Logo – 12’’+12’’ (ii) 1st Line- 6’’ (iii) 2nd Line- 12’’ (iv) 3rd Line- 8’’ (ii) 4th & 5th Line- 6’’

Carring Charges of the manufacturing LED board from co.'s work shop to work site.

M.S. structural work in column beam etc. with simple rolled structural members(e.g. joist, angle chanel,section)

i) For stuctural members of specified sections weighing not less than 22.5 kg per meter.( Page 99, item 1( I ) of PWD schedule)

Supplying M.S. angle (50 x 50 x 5 mm) 4.5 kg/mtr.

Supply of MS base plate (8mmx450mmx450mm) (12kg x4nos. =48 Kg )

Supply of MS base plate (7mmx150mmx150mm) (55kg/Sqmtr.x 0.0225sqmtr. =1.24 Kg )

Supply of MS Channel (150x75x6mm) 16.79 kg/ mtr.

Supplying M.S. flat (50 x 6 mm) (10 mtr.) 1.2 kg/mtr.

Transportation Charge of above materials without Sign board from Co's workshop to worksite. ( 2.5% of total of item no.-1&2)

Cutting and drilling holes on MS plate with grinding the plate. This plate is to be welded with the precutting roof with 4"x0.5" size fastner.

Fabrication charge of the iron structure incl. hiring of welding machine incl. making connection as required.

M/S JOGMAYA ENTERPRISE

MODERN ELECTRICALS

SANJIB GHOSH

MOON LIGHT HOUSE

RAHUL TRADERS

SREE LALJI

EFFORTECH