Supply and Installation of Tensile Fabric Car Parking Shade at New BDA Office Building.

Supply and Installation of Tensile Fabric Car shades in New BDA Building Car parking including design work all complete.(Minimum straight/ Horizontal width to be measured for payment) (i)Material Specifications: (A)Structural Steel: MS Structure Square & Circular Hollow Section as per the Structural Design. The MS Structures are painted with Duco Paints.(B)Tensile Fabrics: A Multi-Layer Composite material with densely woven low-wick yarn in the base fabric.(C)The surface lacquering is done with a new blend of highly concentrated (D)Type of coating: PVC (E)Finish: Nano polymerized fluorinated lacquer, Multi-composed PVDF-lacquer system on both sides, protected against microbial and fungal attack, UV-protected, low-wick, Titanium dioxide (TiO2) front side primer.(E)Total weight: 900 g/m² EN ISO 2286-2 (F)Tensile strength: warp/weft 3000/3000 daN/50mm EN ISO 1421/V1 (G)Tear strength: warp/weft 300/300 daN DIN 53363 (H)Adhesion: 10daN/5cm PA 09.03 (intern) (I)Cold resistance: -40 °C EN 1876-1 (J)High Temperature: +70 °C PA 07.04 (intern) (K)Crack resistance: no cracks 100000 x DIN 53359 A(L) Base Fabric: Material PES low-wick DIN EN ISO 2076 (II)Structure specification (A)Vertical pole - 165 mm OD x 4 mm (B)Rafter-90 mm OD x 3.2 mm (C)Purlin - 76 mm OD x 2.5 mm (D)Support-76 mm OD x 2.5 mm (E)Base plate - 12"x12" thickness- 10mm (F)Profile plates 6mm, 8mm. (G)Fabric-900 GSM, FR, B2 GRADE, PVDF Coated, UV Resistance 10 Year Warranty (H)Nut bolts- M 20,450 mm length foundation bolts (I)Paint - Duco Oil paint/Epoxy 90 micron / Powder coating. (III) Foundation: Civil Foundation as per the design requirement. (A)Steel - For Footing - 10 mm steel & for column - Vertical 12 mm & Stirrups - 8mm. (Make – (B)Reliable/MSP / Runguta/SMC/Titan/Vizag / SEL Tiger / JSW/SAIL/Equivalent) (C)Footing size - 1000 mm X 1000 mm X 450 mm. (D)Column size - 450 mm X 450 mm. (E)Cement - (Make - ACC / Ambuja / UltraTech / Dalmia). (IV) Effectiveness of Guarantee:(A) Compliance with specifications: The Products are in accordance with buyer published technical specifications and free from material defects in components and workmanship affecting performance and durability at the time of delivery and for the period of time and percentages hereinafter detailed. (B)Tensile strength: The Products will maintain at least 70% of their initial tensile strength according to EN ISO 1421 over a period of 10 years from date of invoice, provided that the Product has been designed and installed with an initial safety coefficient of minimum five. Tensile strength measurements will be performed in plain membrane panels, excluding areas where the Product could have been cut or damaged during the installation process or areas where the Product has not been under permanent tension. (C)Flame Retardance and water proofness: The Product shall remain Flame-retardant and waterproof for a period of 10 years from date of invoice. Note-1:- Design Standards: Wind Load:- Basic Wind Speed as per Wind Zones following IS 875 part #3. Seismic Load:- Earthquake resistant as per IS 1893 Note-2:- The above-mentioned cost includes: Loading of material at factory site. Transportation of Material. Steel Superstructure. Labour charges for Fabrication and installation work. Installation service. RCC Foundation as per drawing.