CERTAIN REPAIR SUCH AS JOINERY, SANITARY FITTING, FLOORING, PLASTERING ETC AND REPAIR TO ROOFING, ROLLING SHUTTER AND PERIODICAL SERVICES AND VARIOUS MISC WORK TO CERTAIN BUILDINGS IN TECH AREA AT AF STN HALWARA

Amount

Taking down chowkhats or frame of any description (without taking off shutter from the frame) area n. exc 1.5 sqm each compelte all as specified and directed. Note : The rates for cutting holes/demolition of hold fasts are deemed to be included in the quoted rates and nothing extra shall be admissible on this ground.

All as per Sl Item No 1 here-in-before but area exc 1.5 sqm and n. exc 4 Sqm each

Taking down shutter of any description of size exc 1 sqm but n. exc 2 sqm each leaf compelte all as specified and directed..

All as per Sl Item No 3 here-in-before but area not exc 1.00 sqm each

All as per Sl Item No 1 here-in-before but area exc 2.00 sqm each

S&F 105x60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling the hollow portion of frame with PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) complete all as specified and as directed.

All as per Sl Item No 6 here-in-before but 125x60mm pressed steel frame

S&F 30mm thick glazed or skelton shutters, open rebated prepare to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut or metered beads for securing glass etc, size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 of 2nd class hard wood factory made 30mm thick kiln seasoned and chemically pressued treated complete all as specified and as directed.

S&F 35mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I),Section 8, clause 8.24 of 2nd class hard wood factory made kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 40 mm thick flush shutters, solid core construction with block board core and plywood face panels, commercial type with lipping/frame to match complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing in opening as per specifiecation and drawing complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter with partical board core 28 to 30mm thick (stiles) with 2,4,or 6 raised panel desigen with 2mm moulded PVC sheet on the front face & 2mm plain colour plain PVC sheet on back face and fixing in frame complete all as specified and as directed.

Dismantling wrought iron work or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L framed work of Fe- 410W grade E-250 quality- B as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed.

S&F powder coated aluminium frame for doors, windows, ventilators or in partitions with one or more rebates including joining cleat for fixing etc (minimum thickness of powder coating 50 micron) complete all as specified and as directed.

S&F powder coated aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, zing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws (minimum thickness of powder coating 50 micron) complete all as specified and as directed.

S&F powder coating aluminium window and ventilator shutters, side hung/fixed type without sash bars, aluminium section weighing 0.55 kg/ m including necessary joining cleats, zing clips, ruber neoprene packing, anodised aluminium snap beading screws anodised aluminium fittings such as peg stay, Tower bolt 150mm long 1 No. hinge type B-21 100 mm long 2 Nos, suitable handle 1 No (minimum thickness of powder coating 50 micron) complete all as specified and as directed.

S&F powder coating aluminium grills of any pattern/design weight not less than 1.5kg per square meter complete all as specified and as directed.

S&F prelaminated particle board 12mm thick, interior grade, prelaminated both side with decorative choice lamination, fixed in aluminium door shutter/ Aluminium partition complete all as specified and as directed.

S&F factory made steel window/ventilator box type using ERW hollow 'P' section comprising single frame for and including glazed skelton shutter jointed internally with flat iron 40 x 4 mm complete including grill of 10 mm square bars, fixed horizontally @ 10 cm c/c, hinges, handle, tower bolts, stops, lugs etc, all as shown on drawing No TD - 219(c) sheet 1/3 to 3/3 as applicable complete including cutting holes and making good to dismantled portion with PCC 1:2:4 type B-1 using 20mmg graded stone aggregates for four Nos hold fasts for each window complete all as specified and as directed. . Make : Steel windows manufactured by M/S TEE PEE Enterprises, Amritsar (Pb)/ M/s PD Industries Panchkula (HR)/ M/S Laxmi welding works, Ambala Cantt. or equivalent as approved by GE. Note: (i) Unit rate quoted against this item shall also include the iron mongery and grills as shown on drawings. (ii) Glazing & Painting shall be measured & Paid for separately.

S&F factory made steel window 1.25mm thick sheet box type using ERW hollow 'P' section comprising single frame for and including glazed and gauged skeliton shutter jointed internally with flat iron 40 x 4 mm complete including grill of 10 mm square bars, fixed horizontally @ 10 cm c/c, hinges, handle, tower bolts, stops, lugs etc, all as shown on drawing No TD - 219(c) sheet 1/3 to 3/3 as applicable including cutting holes and making good to dismantled portion with PCC 1:2:4 type B-1 using 20mm graded stone aggregates for four Nos hold fasts for each window complete all as specified and as directed. . . Make : Steel windows manufactured by M/S TEE PEE Enterprises, Amritsar (Pb)/ M/s PD Industries Panchkula (HR)/ M/S Laxmi welding works, Ambala Cantt. or equivalent as approved by GE. Note: (i) Unit rate quoted against this item shall also include the iron mongery and grills as shown on drawings. (ii) Glazing,wire gauged & Painting shall be measured & Paid for separately.

S&F 150mm long aluminium anodised, barrel tower bolt of extruded section and fixed complete all as specified and as directed.

S&F aluminium anodised, barrel tower bolt of extruded section and fixed to 200 mm each

S&F 150mm size extruded section aluminium alloy handles, fabricated type anodised complete all as specified and as directed.

S&F 300mm long alumunium alloy sliding door bolt with hasp & staple and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and as directed.

S&F 100mm long mild steel butt hinges cold rolled medium weight complete all as specified and as directed.

S&F 300 mm long ordinary rat tail rod pattern spring (mild steel) including roller and roller platecomplete all as specified and as directed.

S&F door closer Cast iron body hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed

All as per Item Ser No. 29 above but fixed in repairs

S&F brass Mortice lock vertical type 75mm 4 Levers complete all as specified and as directed.

M&L in repair 40mm wast fittings, brass chromium plated for sink, basins and urinals etc with long screwed shanks and fly-nut flange end beddedin red lead cement and other end fixed complete all as specified and as directed.

Hacking out broken glass (any size shape, thickness, quality or description) from wooden/metal frame glazed with putty or fixed with beads having area not exc 0.50 sqm in each pane complete all as specified

S&F 4 mm thick sheet glass ordinary quality and fixing in frame with glass putty or fixed with wooden beads having area not exc 0.50 sqm in each pane complete all as specified

S&F stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinnd tacks or glvanised wire staples complete all as specified and as directed.

S&F in repair stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and as directed.

S &F in repairs MS coloured hollow curtain rod 19/20 mm dia with two Nos decorative type brackets knobs for each rod of length not exceeding 1.80 mtr including fixing with suitable arrangements complete all as specified and directed.

S&F in repair steel rolling shutters without ball bearing , guide channel as specified including top covers anchoring rod, hasp and staple and one shop coat of primer erect in position as indicated complete push or pull or manual type having thickness of laths 1.00 mm complete all as specified and as directed.,including taking down old rolling shutter etc complete.

All as per Sl item No 40 here-in-before but gear oprated type with bevel gear box and crank handle etc complete.

Supply ball bearing for rolling shutter any suitable size etc complete all as specified and as directed.

Taking down complete rolling shutter any size and refixing in same opening after oil, greasing and making it fully functional and making good the disturbed surfaces area of rolling shutter manual operated each complete all as specified and as directed. Note:- If ball bearing, spring, shaft are unserviceable the same shall be paid seperately undre respective items of this BOQ..

All as per item No 43 here-in-before but of Gear operated

Supply shaft for rolling shutter any suitable size etc complete.

Supply spring for rolling shutter any suitable size etc complete.

M&L for repairing/greasing etc for making sliding door shutter of hangers functional, the area of each door shutter exc 20 Sqm but n. exc 35 Sqm each complete all as specified and as directed.

S&F safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed.

S&F in repair Rorational moulded polythylene water storage tank (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 500 ltrs complete all as spcified as directed. including dismantling old exsiting tank complete all as specified and as directed.

S&F 20mm dia ball brass valves, high pressure,with polythene float and flynut complete screwsed for iron pipe for brass ferrule and fixed etc complete.

S&F in repair wash down water closet (Pedestal pattern) including seat cover and stainless steel water jet including connection to drain pipe (outgoing pipe) and to flush pipe, antisyphonage pipe etc complete all as specified.

S&F in repair vitreous china urinal flat back, size 465mm x 355mmx 265mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern and flush pipe and waste pipe) but including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screwes pointing around urinal back including waste coupling and discharge pipe complete all as specified.

S&F in repair vitreous china squatting pan Orissa pattern of size 580x440mm white with integral foot rest excluding flishing cistern and flush pipe complete including provision of cement concrete bedding in PCC 1:5:10 type E-2 complete all as specified and as directed.

S&F in repair vitreous china wash hand basin white flat back size 550mmx400m excluding taps waste and plug and porcelain stopper but including brackets including cutting for and pinning in ends of brackets or erecting stand but including waste coupling and waste pipe complete all as specified.

S&F in repairs 15mm bore pillar taps cast copper alloy screwed down high pressure with crutch or butterfly handle complete all as specified and as directed.

S&F in repair 15mm bore stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle complete all as specified and as directed.

S&F in repair 15mm bore bib tap cast copper alloy screwed down high pressure with crutch or butterfly handle for iron pipe or brass ferrule and fixing complete all as specified and as directed.

Taking up or down 15mm bore steel water tubing and connection including cleaning for re fixing or removal to store complete all as specified and as directed.

All as per item No 58 above but 20mm bore

M&L for 15mm bore GI tubing medium grade with all fittings complete fixed to wall, ceiling or laid in floors complete all as specified.

All as per item No 60 above but 20mm bore

Fixing only 15mm bore GI tubing of any grade with all fittings complete fixed to walls, ceilings or laid in floors in old or new position complete all as specified. Note : Serviceable tubes obtained from dismantling shall be reused in the work after cleaning.

All as per item No 62 above but 20mm bore

S&F in repair kitchen sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm bowel size 410mm x330mm x 160mm complete all as specified.

S&F in repairs stainless steel towel rail, 20mm dia, D type, 60cm long fixed with and including chromium plated brass screw and wooden /plastic cleat etc complete all as specified and as directed.

S&F in repairs 10 ltrs capacity, PVC valve less, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F in replcement PVC connection pipe 15mm dia with PTMT nut for length 450mm complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and paving’s n exc 15cm thickness below or above ground level complete all as specified and as directed.

Dismantling floor hearth or wall tiles including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for 15mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and as directed.

M&L for rendering 10mm thick on brick work or concrete surfaces in cement mortar 1:4 for rough finished surfaces complete all as specified and as directed.

M&L for 25mm thick cement concrete type B-0 using 12.5mm graded crushed stone aggregate as in sub base finished even and fair surfaces without using extra cement complete all as specified and as directed.

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed. .

All as per Sl item No. 74 above but in vertical surfaces as Dado/Skirting

M&L for vitrified ceramic tiles light shade matt finish 9 to10mm thick (Square/Rectangular) polished area of each tiles n. exc 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles complete all as specified and as directed.

All as per Sl item No.76 Above but as in skirting, dados/Vertical surfaces

M&L for coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles 450X350X7mm or any other size as directed. by GE in vertical surfaces etc set and jointed in neat cement slurry and pointed in white or coloured cement to match.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc, laid bedded and pointed in mortar.

M&L for 75mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in sub base all as specified and as directed.

M&L for 20mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for Machine cut kota stone slab 16-18 mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick cement screed in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for chequered cement concrete tiles 300x300x25 mm thick, with grey cement and no pigment, set and jointed and pointed in neat cement slurry in floors complete all as specified and as directed.

M&L for 16 to 18 mm thick Granite (of any type) machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness including cover fillets of any description all as specified and as directed.

S&F in repairs Anodised aluminium snap grid frame work for false ceiling, size of grid 605x605mm including hangers, cleats, fastenerscomplete all as specified and as directed.

S&F Providing and fixing Gypsum Board 8mm thick in ceiling fixed with screw as per manufacturers instructions, 60x60cm in size all as specified and as directed.

S&F 6 to 8mm thick prelam PVC hollow sheet as in panelling in strip & channel feathered at the edge for fixing on fixed to walls, vertical surfaces of any pattern, complete all as specified and as directed.

Dismantling of AC/fibre glass translucent corrugated or semi corrugated sheet including ridges, hips, valley etc of any description and thickness in roof coverings all as specified and as directed.

Dismantling of plain or corrugated steel sheets of any gauge, thickness in any position all as specified and as directed.

M&L for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe-410 (Gde E-250) complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixing with self taping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixing with self taping screws complete all as specified and as directed.

S&F 2 mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations sid lap fixed with coach screw and washer in roof, wall etc complete all as specified and as directed.

M&L for cement concrete 1:2:4 type B-1 (using 20mm graded aggregate) in hold fasts, roof kerbs or mud stops, rounded or chamfered on edges and similar work etc complete all as specified and as directed.

Dismantling brick tiles or terracing tiles single layer on roof slab.

Demolition of lime concrete of any description and in any position not other wise spacifically provided for roof.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with 3.0 kg of cement per square metre.

M&L 40 mm thick (average thickness) cement concrete type B-1, 1:2:4 (20 mm graded aggregates) as in PCC padding in roofslaid to maintain slope complete all as specified and as directed.

M&L for 15mm thick screed bed in cement mortar 1:4 mixed with proofing compound as per manufacture, finished even and fair complete all as specified and as directed Note water proofing compound will measured and paid separately as supply only.

Supply only Integral waterproofing compound

M&L preparation of roof top surfaces, providing and applying single component elastic cold applied polyurethene modified acrylic roofing system,co elastic technology (CET) based on polyurethene and fully fiber reinforced,having sun reflectivity index (SR) of 106 on top of concrete roof surfaces,All cracks up to 3mm at corner joints,channel and parapets should be treated with crack seal.Aapplying three coat including one coat of primer of Shali Urethne BTD/ Sikalastic 560/smart care damp Proof Ultra having coverage @.75kg/sqm and dilution up to 10% and laying reinforced fiber net and applying two coat of shaliurethene BTD/Sikalastic 560/smart care damp proof ultra @total consuption 2Kg/Sqm in two coat of maintaining minimum dry film thickness 1.5mm and elongation at break of free film of approx 350%.The materials shell be applied with brush or roller , complete in all respect as per the direction of Engineer-in-charge/Consultant (Note :6 Hrs interval between two coat will be mantain) All auxilary and accessories involved during application should be supplied by single manufacturer as a part of system. Make: STP, Sikka ,Asian paint or equvalent as approved by GE. (i).The water proofing treatment shall be carried out by the manufacturer and their authorised applicater duly approved by GE in writing. (ii) 5% amount of the total amount of water proofing treatment shall be retained as a guarntee and shall be released after 10 years.however contractor may doposit the FDR of same amount in favor of GE.If contractor fail the rectify the defects point out during this period in writing,the defect shall be got rectified at contractore risk and cost and the pyment shall be made from the amount kept reserved or by encashing the FDR deposited by the contractor as guarantee.The contractor quoted rates for this item shall deemed to inclusive of this aspect.

Taking down cement plastered including racking out joints hacking for key scrubbing down with water etc complete all as specified.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc complete all as specified.

M & L for brick works with sub class 'B' bricks straight or curved on plan exc 6m mean radious, built in CM 1:6 complete all as specified and as directed.

All as per item No 107 above but except bricks . Note : Serviceable bricks obtained from Sl item No 106 above shall be reused in the work after cleaning.

M&L for 12mm thick plaster in CM (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished surfaces fair and even without using extra cement complete all as specified and as directed.

M&L for rendering 5mm thick on fair faces of ceiling in CM 1:3 finished surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of new plaster surfaces of wall and applying two coats of synthetic enamel paint over a coat of primer in camouflage pattern, using minimum 3 different approved tint/ colour as approved by GE complete all as specified.

M&L for preparation of new plastered surfaces,of wall and applying two coats of distemper oil emulsion, over a coat of primer over a layer of birla putty, complete all as specified and as directed.

M&L for preparation of new plaster surfaces of wall and applying three coats of white wash complete all as specified and as directed.

M&L preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new wooden surfaces and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

M&L for preparation of old decorated plastered & unplastered surfaces of walls by brooming down or steel wire brushing, scrapping down smoke soot mould moss and efforescent salts trading oil and greasy spots, filling holes cracks with wall care putty all and applying two coat of white wash complete all as specified and directed.

All as per Srl item No. 118 above but two coats of white wash on ceiling surfaces.

All as per Srl item No. 118 above but one coat of oil bound distemper on wall.

All as per Srl item No. 118 above but two coat of oil bound distemper on wall.

M&L for preparation of old painted wood or wooden based surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified

All as per Srl item No. 122 above but on steel and iron surfaces

Demolition and breaking up rain water pipe in any description and any position.including all accessories complete all as specified and as directed.

S&F stack clamps for 100mm dia pipe made of 50 x 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

S&F PVC (SWR)110mm dia pipes double socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S$F 110mm dia PVC (SWR) bends any radius complete all as specified and as directed.

Preparation of old plaster surfaces of wall and applying two coats of synthetic enamel paint in camouflage pattern, using minimum 3 different approved tint/ colour as approved by GE complete all as specified.

M/S SANGA SINGH AND CO

CHOUDHARY ENTERPRISES

BEHL AND COMPANY