SE(GRWW,PH-I)/T-02 of 2019-20(2nd Call)

Amount

DESIGN , DRAWING AND CONSTRUCTION and COMMISSIONING OF INTAKE JETTY AND JETTY MOUNTED PUMP HOUSE OF 185 MLD CAPACITY AND SUBSTATION BUILDING , BANK PROTECTION WORK AND ANCILLARY WORKS WITH LANDSCAPING, ROAD ETC. ALL COMPLETE.

Hydraulic, Marine and Soil Investigation Survey

River Bank Protection Work

Civil Works including piling works

Erection & Commissioning

Landscaping and Boundary Wall with Gate

Laying of 1600 mm dia, 12 mm thick M.S Raw water rising main from Raw water pump house upto 400 Mtr battery Limit with Road Restoration and 5 yrs Operation & maintenance

Supply of MS Pipes

Road Profile Survey work

Laying of pipe, all Civil Works and temporary road restoration work all complete

Permanent Road Restoration Work

Supply, delivery at site and installation of vertical turbine pump motor set complete having the following head discharge characteristics , capable to discharge raw water ,having SS(CF8M) impeller, CI casing , dischagre head ,motor stool along with other standard accessories with CACA/ TEFC , 8 pole, 3 Phase, 11 KV ± 10% AC. Insulation class F , IP 55 , Squirrel Cage Induction motor of suitable ratings as required and as per technical specification and direction of EIC and as per CPHEEO standard . Motor shall have a margin of 1.2 over the pump BKW at duty point. Pumps shall be installed on suitable RCC foundation within SS 316L caission pipe ,adhering to all the technical requirements of the pump manufacturer. Make : Pump :WPIL / Mather & Platt / KBL . Motor :CGL/Marathon/Siemens/ABB 2250 m³/hr against a tentative head of 70 MWC ( 4 nos working + 3no. Standby ) (Finally actual TDH to be determined by the tenderer at the time of detailed engineering after consultation with the concerned divisions dealing with the WTP , pipe laying and constructing the intake jetty)

Supply, delivery at site, installation and commissioning of HT soft starter for individual motor feeder along with all acessories , cables , kits, etc.

Supply, delivery at site, installation of 17-Panel HT Switch Board of 500 MVA, 11 KV ,25 KA , 800 Amps , VCB complete in all respect with all other accessories as per technical specification and direction of EIC. ( 2no incomer, 1 no bus coupler, 7 nos motor feeder, 4nos. capacitor feeder , 2 nos transformer feeder,1 no. spare motor feeder) Make : Schneider/ Siemens / CGL / ABB

Supply, delivery at site, installation of minimum 150 KVA, 11 /0.433KV as required (To be finalised during detail Engineering ), ONAN outdoor Transformer complete in all respect with all other accessories as per technical specification and direction of EIC conforming to IS :1180 , Level-II ( 1no. Working + 1no. Standby) Make : KEC / Schneider / CGL / ABB

Supply , delivery at site and instalation commissioning of 12 KV grade Capacitor Reactor of suitable rating with RVT in all respect as per technical spesification and direction of EIC

Supply, delivery at site, installation of LT. P.D.B. complete in all respect with 1400 VA , 2 nos inverter with battery along with all other accessories as per technical specification and direction of EIC. . ( 2 nos. incomer ACB , 1 no. bus coupler , Lighting feeders, Valve actuator feeder , EOT crane feeder, and other auxiliary loads as required as per technical specification and direction of EIC . Make : Sellwin Electricals Pvt. Ltd. / PCE Project Pvt. ltd / Hindustan Control / Sunshine Control / Industrial Switch Gear.

Supply, delivery at site, installation of central control desk complete in all respect with all other accessories as per technical specification and direction of EIC. Make : Sellwin Electricals Pvt. Ltd. / PCE Project Pvt. ltd / Hindustan Control / Sunshine Control / Industrial Switch Gear

Supply, delivery at site, installation of 110Volt DC Battery Charger with maintenance free battery complete in all respect with all other accessories as per technical specification and direction of EIC.(capacity to be determined during detailed engineering.) Make : Electro Service /Dekem/Caldyne

Supply, delivery at site , fitting and fixing of electro-magnetic flow meter of following sizes , comprising of flow sensor and transmitter, signal conditioner if required, flow indicator, flow totaliser(controller unit ) and all other accessories complete as per specification and direction of EIC. Make : Endress& Hauser / Chrone Marshall / Emerson 1400 mm

Supply, delivery at site fitting and fixing of following MS pipe including fabrication of all necessary accessories special viz dismantling joints, Puddle plates(20mm), Bell Mouth, bends, tees, enlarger/reducer, R.C.C. pedestal for common manifold , etc including cutting walls, pipes, making flanged & welded joints as required, fitting fixing complete in all respect including cost of all fitings, sundry and jointing materials as required for laying of pipe with anti-corrosive treatment of all pipe surface complete as per technical specification and direction of EIC.

Dia -600 mm. of 12mm thick (For individual delivery piping)

Dia 600mm , DF Metallic dismantling joint with split flange, long stud, bolts, nuts etc.

1600 mm , 16mm thick (For common manifold piping)

1400 mm , 12mm thick (For flowmeter piping)

Supply, delivery at site, lowering, fitting and fixing of DIDF non return valve (PN-1.6 ) with suitable damping arrangement , of following size in proper position and alignment by providing permanent support as required including cost of all sundry materials such as gaskets, nuts, bolts etc. all complete as required to complete the job in all respect as per technical specification and direction of EIC.

600mm Dia

Supply, delivery at site, lowering, fitting and fixing of DIDF butterfly valve (PN-1.6) alongwith suitable rated motorised actuator of following size in proper position and alignment by providing permanent support as required including cost of all sundry materials such as gaskets, nuts, bolts etc all complete as required to complete the job in all respect as per technical specification and direction of EIC.

Dia : 600mm ( for individual delivery)

1400 mm dia (after flowmeter )

Supply, delivery at site, fitting and fixing of submersible pump, starter panel , including deep tubewell , piping , gun metal gate/globe / check valve/OHR for drinking water lines complete with accessories including cost of all sundry materials and fitting fixing charges as required as per technical specification and direction of EIC.

50mm dia Gate / Globe Valve

32mm dia Gate / Globe Valve

50mm dia Check Valve

Supply, delivery at site, fitting and fixing of single orifice type air release valve with isolation valve of adequate size for individual pump (4 inch) and manifold pipe line (8 inch) complete with all other standard accessories including cost of all sundry materials and fitting fixing charges as required as per technical specification and direction of EIC.

Supply, delivery at site, fitting and fixing of dust & damp proof following field instruments complete with all valves, cocks and other fixtures including cost of all sundry materials as required as per technical specification and direction of EIC.

0-15 kgf/cm² (6" dial bourdon type for individual delivery line,accuracy ± 1%)

0-15 kgf/cm² (8" dial bourdon type for common delivery manifold,accuracy ± 1%)

Pressure transmitter including cabling (For individual delivery line )

Pressure transmitter including cabling (For common delivery manifold )

Supply, delivery at site fitting and fixing of the ultra sonic water level sensor with indicator including transmitter / transducer / stilling pipe and all other accessories including all cabling connections all complete as per specification and direction of EIC.

Supply ,delivery at site and laying of 11 KV grade XLPE insulated, PVC outer sheathed, armoured, aluminium conductor cable of following size either through cable duct or through cable trays or through protection pipes as per technical specification and direction of EIC.

3 core x 300 (or as required )mm² ( CESC room to KMDA HT panel to transformer yard ) .

Supply, delivery at site and laying of 1.1KV / 11 KV grade XLPE / PVC insulated, PVC outer sheathed, armoured, aluminium conductor cable of following size either through cable duct or through cable trays or burried underground through brick protection or through protection pipes as per technical specification and direction of EIC.

3 core x As required mm² HT motor feeder to motor terminal & capacitor bank

3.5 core x As required mm² TXR(LT) to LT panel.

Supply, delivery at site and laying of 1.1KV grade XLPE insulated, PVC outer sheathed, armoured, stranded copper /aluminium (as applicable) conductor auxiliary power and control cable of following size either through cable duct or through cable trays or through protection pipes as per technical specification and direction of EIC.(minimum 2.5 mm² ) Including signal cable.

Making end termination of 11KV grade 3 core x 300 (as required )mm² XLPE insulated, PVC outer sheathed, armoured, aluminium conductor cable with push on type premoulded cable jointing kit indoor/ outdoor type as required complete with gland and other hardwares as per direction of EIC.

Making end termination of 1.1KV grade XLPE/PVC insulated armoured Al./Cu. conductor cable with gland and other hardwares of following sizes as per direction of EIC

Earthing the whole installation as per IE Rules & Acts, specifications, complete in all respect including supply,installation of all required earthing materials,flats,earth electrodes and all other sundries, including lighting arrestor ,fitting,fixtures including making proper earth stations as per technical specification and direction of EIC.

Providing fencing with structural gates around the periphery of the transformer (11 /0.433KV )yard as per I.E. rules including supply and fixing of necessary M.S. angles, flates G.I. mesh etc. as required to complete the job as per specification and direction of EIC.

Supply and fixing of E.I. Danger board on wall & fencing as per direction of EIC

Supply and providing 11KV grade rubber mat as per direction of EIC.

Supply and fixing on wall a shock treatment chart duly framed by polished wood and the glass fitted in front complete as per direction of EIC.

Display of back lit & non lit sign board of various sizes on the pump house wall fascia or elsewhere as per direction of EIC.

Supply ,installation & commissioning, of 15 MT double girder capacity EOT crane complete in all respect including testing , certification by inspector, as per technical specification , rules and direction of EIC.

Painting the whole installation as per technical specifcation and direction of EIC.

Carrying out high pressure test of the HT installation by approved agency and obtaining necessary clearance fron Directorate of Electricity as per direction of EIC.

Supplying ,fitting , fixing & commissioning of all the entire indoor and out door illumination , earthing, glow sign , indications ets as per IS standard and as per satisfaction of the EIC. Ratings and price breakup to be finalised during detailed engineering and approval .

Supply of drawings for approval and finally as-built drawings in 6sets and CDs .

Supply ,fitting, fixing of MS walkways, stairs, tray covers, cable trays, etc as required with proper epoxy paint as per direction of EIC.

Supply, delivery at site & laying of MS pipe including fabrication of all necessary accessories special ,enlarger, ,R.C.C. / fabricated pedestal , thrust blocks , etc including cutting pipes, making flanged & welded joints as required, for joining the common delivery manifolds with the existing prelaid rising main pipes complete as per technical specification and direction of EIC. Note : Any mechanical or electrical or civil , parts/spare/equipment not included in the BOQ but required to complete the project is to be supplied by the agency at free of cost .

Trial run 3 months and commissioning of the entire installation as per specification and direction of EIC.

Operation and maintenance of the entire RWPS for a period of five(5) year along with supply of trained staffs , consumables and spares, as required to run the plant to its desired capacity.

G B CONSTRUCTION