Reconductoring 11KV OH line with HT ABC(3 x 120) from Uchakada to Punnavila under Electrical Section, Kottukal of Electrical Division, Neyyattinkara under Electrical Circle, Kattakada

Fitting and providing one HT Stay for 11kV pole, including digging and back filling pit in ordinary soil.

Renewal of existing damaged/broken old 11kV Stay to the existing stay rod.

Fitting and erecting one HT PSC Single Pole in position, including fitting cross arm, digging and back filling pit in ordinary soil (as per standards), drawing sufficient length of GI earthing leads from F clamp through V cross arm to the ground for earthing (excluding provision of earthing).

Labour charges for loading HT PSC pole from the stacking place and unloading the same at work site (transportation by any vehicle).

Additional rate for refitting/redoing one Shackle Set, including reshacling one span, while renewing any type of LT pole.

Transferring LT three phase 4/5 wire OH line to newly erected HT/LT pole including dismantling existing cross arm and insulators, refitting the same on the new pole, binding etc. complete.

Dismantling one ordinary street light/CFL/LED fitting from existing pole and refitting the same on newly erected pole including disconnecting and reconnecting wires.

Dismantling one 2x40W fluorescent tube fitting from the existing pole and refitting the same on newly erected pole including disconnecting and reconnecting wires.

Disconnecting and lowering down the single phase WP service connection with guy wire from the OH line and reconnecting the same after completing the line work.

Dismantling (without damage) one HT stay including digging pit in all classes of soil and backfilling, and bringing back to section store.

Dismantling (without damage) LT stay including digging pit in all classes of soil and backfilling.

Transporting poles by hired vehicle to a distance upto 5km and carrying upto 4 numbers of poles excluding loading& unloading charges.

Fitting and erecting one HT A type Single Pole in position, including fitting cross arm, digging and back filling pit in ordinary soil (as per standards), drawing sufficient length of GI earthing leads from F clamp through V cross arm to the ground for earthing (excluding provision of earthing).

Labour charges for loading HT A type pole from the stacking place and unloading the same at work site (transportation by any vehicle).

Providing concrete muffing of size 0.45x0. 45x1.5m (0.5m above GL and 1m below GL). Excavation 0.45x0.45x1m, concrete (1:3:6, 20mm) 0.45x0.45x1.5m, Plastering (1:3) 12mm 0.45x0.45mx5sides.

Pole numbering using printed Aluminium sheets of 22 SWG having size 20 x 12 cm or Painting the surface of line supports where numbers are to be inscribed, Pole numbers shall be painted in circular / rectangular background, using approved quality anti algal yellow paint in two coat after scraping and cleaning the surface at a height of 2.5 metre above ground level. The number and letters should be in black synthetic enamel paint. The size of the number should be at least 2cm in height x 1.5cm in width. including cost of paint.

Fitting one Additional 75x40mm, 1.8m Channel cross arm in existing single pole including conveyance of materials.

Fitting one LT 2 line cross arm on HT or LT existing poles including fitting insulators and binding the same with LT Line.

Fitting one LT 4 line cross arm on HT or LT existing poles including fitting insulators and binding the same with LT Line.

Disconnecting and lowering down the three phase WP service connection with guy wire from the OH line and reconnecting the same after completing the line work.

Erection of Anchor clamp / dead end clamp for 11kV ABC of any size

Stringing of 11 kV Aerial bunched cable of size 3 x 120 + 1 x 95 sqmm with bare/insulated Messenger through existing poles

Providing one Coil Earth using No.8 GI-earth wire (50mm dia, 115 turns) including digging separate pit (0.45x0.45x1.5m) at standard distance away from the pole/structure in ordinary soil & backfilling.

Providing one Earth using GI earth pipe of size 38.1mm dia, 2.5m length including digging separate pit (0.45x0.45x2.5m) at a minimum distance of 1.5m away from the pole/structure and maintaining standard distance between different earth pipes in ordinary soil & backfilling.

Fiting One no MVT on existing cross arm including 2 nos end termination (for One phase) of any rating for 11 kV AB Cable

Fitting one No. LT lightning arrestor in LT OH line and giving connections excluding earthing.

Erection of suspension clamp for 11KV ABC of any size

Dismantling (without damage) one km 11kV line (three conductors) including dismantling cross arm, insulators, disc, disconnecting jumper connection, rolling the conductor and stacking the materials.

Dismantling (without damage) one 11kV PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling (without damage) one LT PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling one damaged LT PSC/RCC pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling one damaged LT TW/RSJ/Rail pole after disconnecting stays, strut etc. attached thereon and stacking the same.

Dismantling (without damage) one V cross arm/Channel cross arm from existing Pole and bringing back to section store.

Dismantling (without damage) one LT PSC/RCC Strut pole including removal of clamps and stacking.