SPECIAL REPAIR INCLUDING ROOF TREATMENT OF BLDG NO P-90 AT CERTAIN MILITARY UNIT, PROVN OF HARD STANDING AT MEAS AREA AND PROVISION OF RAIN WATER DRAINAGE SYSTEM FROM P-08 (ADM BLOCK) TO MAIN DRAINAGE LINE AT BINNAGURI MIL STN UNDER GE (S) BINNAGURI

Amount

Taking down chowkats or frames exc 1.5 Sqm and n.exc 4 Sqm (without taking off shutter from the frames) and removal from site complete all as specified.

All as item No 1 here-in before but n.exc 1.5 Sqm each complete all as specified.

Dismantling floor hearth or wall tiling including cement mortar bedding (incl backing) removing serviceable tiles to store and rubbish off the premises complete all as specified.

Taking down cement plaster any description on brick or stone wall etc including racking out joints hacking for key scrubbing down with water etc complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for grils.rails etc complete all as specified.

Demolition of brick work or stone /boulder masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified.

Demolition of PCC of any description and in any position not otherwise specially provided for and removal of rubbish off the site all as specified.

Taking down tarfelt with cement plaster from roof surfaces and lowering and removing the same to a distance exc. 500m and n. exc. 900m incl roughening of old concrete suirface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified.

Demolition of reinforced cement concrete in any description and in any position (reinforcement cut as required to facilitate demolition) complete all as specified.

M&L for glazed coloured ceramic tiles (450x350x7mm thick) on vertical surfaces such as skirting/dado set and jointed in neat cement slurry pointed in white or coloured cement to match over 15mm thick rendering in CM(1:4) all as specified.

M&L for non-skid ceramic coloured (400x400x7 to 8 mm thick) tiles set and jointed in neat cement slurry pointed in white or coloured cement to match in floor over 15mm thick screed bed in CM(1:6) all as specified.

M&L stepping stone 15 mm thick of colour as approved as in riser/vertical surface of stair case set and jointed in neat cement slurry over and including 10 mm thick rendering/back coat in cement mortar 1:4 complete all as specified.

M&L 75mm thick PCC (1:3:6) type C2 as in plinth protection/footpath using 40mm graded stone aggregate finishing cement concrete surface even & smooth without using extra cement including bitumen filling in panel etc complete all as specified

M&L for 25 mm thick PCC (1:2:4) type B1 ( 20mm graded stone aggregate) , finished concrete surfaces even and rough to receive floor finishes complete all as specified.

M & L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, Copping, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified.

M&L for providing cement concrete type B-0 (1:2:4)(using 12.5 mm size graded aggregate) in coping set incl weathering, slightly rounded or chamfered angles & thickness complete all as specified.

M & L PCC (1:2:4) type B1 (20mm graded aggregate) as in roof kerbs, slightly rounded or chamfered on edges, mixed with water proofing compound @200 ml per bag of cement or as per manufacturer instructions finished even and smooth on exposed concrete surface without using extra cement all complete as specified and as directed. Note: Water proofing compound shall be measured and paid perarately under relevant item of schedule 'A'.

Materials & labour for reinforced cement Concrete 1:1.5:3 type A1 (using 20 mm graded aggregates), nominal mix, as in chajjas and similar work complete all as specified. Note: Reinforcement and formwork shall be measured and paid for separately.

Use and waste of formwork to sides and soffits of beam, chajja, lintle etc for rough finished flat surfaces of concrete all as specified.

Dismantling water tanks and removing to store of capacity exc 250 & n.exc 500 ltrs complete all as specified.

Material and labour for hoisting and fixing rotational moulded polyethylene(double layer) LLDPE water storage tanks 500 lit capacity (Cylinderical vertical with polythene foam insulation as intermediate layer), ISI marked(IS-12701:1996) hoisted and fixed in position including inlet, oulet and over flow connection etc complete all as specified.

Disconnecting existing tanks of capacity exc 250 Ltrs and n. exc 500 Ltrs, setting aside (or lowering if required) for repairs with all necessary fitting as required , cleaning, etc. and hoisting if required reconnecting and re-fixing in same position after cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified.

S&F 20 mm dia PVC ball cock (PVC float valves) complete high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut complete all as specified.

S&F for pressed steel frames for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete, as specified, size of frame 125 x60 mm complete all as specified and directed

M&L for plain, framed, factory made panelled shutters 35 mm thick (any number of panels) , with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers; supplied and fitted to chowkats complete all as specified.

S&F second class hardwood, factory made glazed and skelton shutters 35 mm thick open rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I Section8, Clause 8.20 (a) supplied and fitted to chowkats complete all as specified.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing on SI page No 156 of SSR Part-II complete all as specified.

S&F Solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specification and drawing on SI page No.160 of SSR Part-II complete all as specified and directedd.

S&F Powder coated aluminium louvered ventilators of size n exc 0.50 Sqm area with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing , anodised aluminium snap beading,screws, anodised aluminium fittings and 5.5mm thick tinted glass fixed in panels with suitable locking arrangements including taking down of old existing steel ventilator and making good disturbed surface of wall complete all as specified.

S&F of factory made steel windows with side hung shutters openable type including friction/projected type hinges steel handle and peg stay complete without glazing bars fixed to existiog opening and making to match as per existing surfaces complete all as specified.

S&F of factory made steel windows with side hung shutters openable type including friction/box type hinges steel handle and peg stay complete with glazing bars fixed to existiog opening and making good to match as per existing surfaces including taking out old/unserviceable steel windows complete all as specified.

S&F Framed work such as grills,gratings, etc with ends of bars shouldered and/or riveted,or forged into spikes; framedguard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

M&L brickwork with sub class B bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete all as specified.

M&L for brickwork with sub-class 'B' brick, straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified.

M&L for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar (1:6) finished even & fair complete all as specified.

Material and labour rendering 20 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete work surfaces in two layers 10mm each layer and top 10mm layer mixed with integral water proofing compound all as per manufacturer's instruction and as specified. Make: 'Plastocrete Plus' of Sika/ 'Pidiproof LW' of Pidilite for water proofing compound. Note: WPC shall be measured and paid for separately as 'Supply only'.

Supply only liquid water proofing compound complete all as specified.

M&L for 5mm thick in CM 1:3 in ceiling finishing the surfaces even and smooth without using extra cement complete all as specified.

M& l for two coat of acrylic distemper on new wall surface including preperation of the surface all as directed and specified.

M&L for applying 1.5mm thick wall care putty on new or old wall surface all as directed and specified complete all as specified.

M&L applying two coats of weather proof exterior emulsion paint of standard quality and make ,over a coat of white primer including preparation of new /old wall surfaces complete all as specified.

M&L for two coats of synthetic enamel painting to new wooden surfaces over a coat of pink primer including preparation of surfaces area exc 10cm width & girth complete all as specified.

Material & labour for preparation of old painted surfaces of wood & wood based materials over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or girth complete all as specified.

Material and labour for applying one coat of synthetic enamel paint on old painted steel and iron surfaces of any description over 10 cm in width or girth including necessary preparation of surfaces complete all as specified.

Complete removal of existing treatment from plastered or unplastered surfaces of walls including cleaning with scrapers, any number of coats and any width or girth etc and applying two coats of acrylic distemper over a coat of primer over super fine wall putty 1.00 thick (average thickness) finish as required and complete all as specified.

Material and labour for preparation of old plastered ceiling surfaces by brooming down or steel wire brushing: scrapping down smoke soot, mould, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified.

M&L for applying three coat of white washing including preparation of new or previously untreated surface of ceiling complete all as specified.

M&L applying three coat of white wash including preparation of new wall surfaces complete all as specified.

M& L for form work to chajjas and similar items including edges ,rough finished surfaces of concrete flat complete all as specified.

M&L for mild steel TMT bars,10mm dia and over cut to length, bent to shape required including cranking ,bending spirally, hooping for columns, hookings/ends and binding with and including MS wire not less than 0.9 mm dia or securing with clips complete all as specified.

M&L for mild steel TMT bars 6mm to 8mm dia cut to length , bent to shape required, including cranking , bending and binding with MS wire , not less than 0.9 mm dia or securing with clip complete all as specified.

M&L for MS flat iron bent to shape, holes drilled etc complete as in hold fast & wind ties etc including one coat of red oxide paint complete all as specified.

M&L for 10mm thick screed bed or bedding layers in cement mortar (1:4) in order to maintain proper slope over existing roof surfaces for applying single component acrylic polymer modified, finished even and smooth without using extra cement complete all as specified. (NOTE : Polymeric membrane shall be measured and paid separately under relevant item of this Schedule 'A').

M & L water proofing treatment to RCC roof slab including parapet comprising of the following course of treatement / specified from bottom to top (a) Applying Bituminous primer @ 0.40 Ltr per Sqm over plastered surfaces of roof including parpet surfaces. Bituminious primer shall be 'Tar Mastic' manufactured by M/S STP LTD or 'EMW FLATE' manufactured by M/S Texsa India Ltd. (b) Over the priming coat laying one layer APP based polymeric membrance of approved manufacturer, 3 mm thick of weight not less than 3.60 Kgs/Sqm reinforced with non woven polyester fabric weight not less than 160 gms per Sqm. Polymeric members shall be taken to a height of 60cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrance flashing.

-----Contd Ser No 56--- (c) Application of two coat of bituminous aluminium paint over the polymeric membrane after necessary preparation and cleaning. Note :- (i) Laying APP based polymeric membrance shall be done by torch on method or as per manufacturers instructions. (ii) A minimum overlap of 100mm shall be made at the end and 75mm shall be made at the sides of the polymeric membrance respectively and sealed all ovelaps and joints as per Manufacturers instructions. (iii) APP based polymeric membrance shall be "SUPER THERMOLAY" manufactured by M/S STP LTD or MOPLY FP manufactured by M/S Texsa India Ltd complete all as specified.

M&L for cutting out cracks to 'V' section (shape) in existing roof slab terracing cleaning out and filling solidely with cement and sand mortar (1:1) complete all as specified.

M&L 25 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) as in floors as levelling course for roof treatment complete all as specified.

S&F of stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with tinned tacks,or galvanised wire staples.or wooden beadings for doors complete all as specified.

S&F of in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4mm and fixed with tinned tacks,or galvanised wire staples.or wooden beadings for doors complete all as specified.

Taking up or down steel water tubings bore 15mm dia and fittings etc complete and making good disturbed surfaces of walls/ceilings etc complete all as specified.

ALL as per item no. 61 but bore tubing 20mm dia complete all as specified.

ALL as per item no. 61 but bore tubing 25mm dia complete all as specified.

M & L for steel tubing 15mm bore dia medium grade,galvanised fitting fixed complete to walls and ceiling or floor complete all as specified.

ALL as per item no. 64 but bore tubing 20mm dia complete all as specified.

All as per item No 64 here-in-above but fixing only complete all as specified.

Al as per item No 64 here-in-above but fixing only complete all as specified.

S&F in repairs of PVC low level flushing cistern, 10 ltr capacity, syphonic action type white body with inlet ball valve, float , handle, bracket, long flush pipe of PVC to suit flushing cistern ( long bend) etc complete & connecting to WC Make : Sleek of Hindware, Slimline of Parryware or equivalent as in the list of makes.

S&F in repair Vitreous china wash down water closet pan (pedesatal pattern) (EWC) white including plastic water closet seat cover closed pattern with flat bottom, and cover and mild steel chromium plated hinging divice etc complete fixed in repairs complete all as specified.

S&F in repair PVC seat cover for pedestal pan, white closed pattern with flat bottom and cover and mild steel chromium plated or aluminiumised hanging device complete all as specified.

Supply and fix in repair CP Health Faucet of premium quality and make Jaquar or equivalent including two way bib cock and PVC telephonic flexible tube fixed to 15mm bore pipe.

S&F in repair Water Closet (squatt pattern) of vitruous china squatting pan of pattern "ORRISA" pattern size 580 x 440 mm white with integral foot rests (excluding flushing cirstern and flush pipe) including connection to trap and flushing pipe anti syphon pipe etc complete including trap set in and incl concrete complete all as specified.

Supply and fix in repair for vitreous China flat back urinals(white) of size 440mm x 315mm x 265mm, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including waste pipe, 15mm dia PVC connector pipe , CP urinal spreader complete all as specified. Make: Hindware Cat No 60001 or equivalent as in the list of makes.

Supply and fix in repair for vitreous China wash basin white, flat back, size 550 x 400 mm with CP brackets (02 Nos) including cutting for pinning in ends of brackets and making good disturbed surfaces with CM (1:4) complete all as specified. Make:-HINDWARE Cat No 10054 (Mini Regal) or equivalent as in the list of makes.

S&F of PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified.

S&F in repair 15 mm bore two way bib cock CP with flage complete all as specified and direcrted.

S&F in repairs bib taps 15mm bore fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S&F in repairs for 15 mm bore stop cocks fancy type, chromium plated reduce body, long shank, cap (concealed type) screwed down high pressure screwed both ends for iron pipe or for union etc as in repair complete all as specified.

S&F in repairs angle valve, fancy type chromium plated, brass, 15mm bore complete all as specified.

S&F in repair Brass CP mixer for mixing hot & cold water screweddown for iron pipeand fixed complete all as specified.

S&F in repair central hole basin mixer for WHB complete all as specified.

S &F in repair stainless steel curtain rods 20 -25 mm dia 1.00mm thick with fixing brackets, stops and complete fitments all as specified.

Supply and fix PVC (SWR) pipes 110mm dia type 'A', single socketed, conforming to IS-13592:1992 in any length with rubber ring joints laid in trenches or in floors complete all as specified.

S&F for PVC (SWR) bends any radius fixed to PVC Pipes/Steel Gutters etc complete all as directed. (Bore of pipe 110mm)

S&F 110mm dia PVC (SWR) branch piece single (single 'Y'/T) equal or unequal with acess door complete all as specified.

S&F 110mm dia PVC SWR vent cowl complete all as specified.

M&L in repairs for CI Nahani trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1(diameter of outlet 75 mm) as in repair complete all as specified.

ALL as per item no. 87 but 50mm dia complete all as specified.

M&L for 150 mm size aluminium anodised cast type handles complete all as specified.

S&F of 200mm long aluminium anodised,barrel tower bolt of extruded section complete all as specified.

S&F 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

S& F of 140 mm Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified.

S&F 100mm size mild steel butt hinges medium weight complete all as specified.

M&L for pre polished coloured chequered cement concrete tiles made with grey cement and pig-ments of size 30 cm x 30 cm x 25 mm thick, set, jointed and pointed in neat cement slurry over in pavement / footpath / floors over incl 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified.

Material and labour for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in surface channels and drains complete all as specified.

M & L for cement concrete 1:3:6 type C2 using (40mm graded stone aggregate) as in foundation filling mass concerete complete all as specified

M&L for Plain Cement concrete (1:4:8) type D2 (Using 40 mm graded stone agg) in foundations,filling and mass concrete complete all as specifide as directed.

M & L for brick work with sub class B bricks laid on edge on vertical inclined sides of drain, bedded and jointed in CM (1:6) and pointed in CM (1:3) complete all as specified.

M & L for brick work with sub class B bricks laid flat on vertical inclined sides of drain, bedded and jointed in CM (1:6) and pointed in CM (1:3) complete all as specified.

M & L for hard core of gauge not exc. 63 mm, deposited, spread and leveled in layers not exc. 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified.

Material & labour for providing precast cement concrete 1:1.5:3 type A1 in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry),stringcourses, copings kneelers, apex stones, pier caps,columns, posts, boundary pillars,bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin).corbels, brackets, etc. (of any section indicated), withplain fair faces,including chamfers,weatherings,throating etc. and setting in mortar 1:4 including necessary formwork complete with joints to match complete all as specified. Note: Reinforcement shall be measured and paid for separately.

Surface excavation n.exc (not exceeding) 30 cm deep and avg 15 cm deep and getting out in soft / loose soil complete all as specified.

M & L 60 mm thick M-35 grade factory made vibratory compacted cement concrete rubber moulded, interlocking paver block any shape and size confiroming to IS 15658-2006 with grey cement and pigment as approved laid over and incl 25 mm thick consolidated sand cushion and joints filled with sand complete all as specified.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified.

M&L for point wiring complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LS cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LS (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sundn terminal box made out of GI sheet steel not less than 1.22 mm thick for boxes upto a size of 200 x 300mm and above this size not less than 1.63 mm thick duly painted with aluminum inside and anticorrosive paint outside,

-----Contd Ser No 105 ---- concealed in walls, with 3mm thick bakelite/plastic laminated sheet top cover fixed with cadmium plated iron screws for housing switches, socket outlets, fan regulators etc duly earthed including cutting chases of existing wall for conduits and sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. Connections of cable with MCBs or bus bar shall be sone through proper size copper/brass thimbles. Where concealing of conduit is not feasible ie on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost, One light point controlled by one way switch 5/6 amps all as specified and as directed.

ALL as per item no. 105 but One ceiling fan/Exhaut fan point controlled by one way switch 5/6 amps complete all as specified.

ALL as per item no. 105 but One socket out let 5/6 amps point on the same board complete all as specified.

ALL as per item no. 105 but One socket out let 5/6 amps point on the independent board complete all as specified.

ALL as per item no. 105 but One light point controlled by two way switch 5/6 amps complete all as specified.

All as per item No 105 above but wiring with 4.00 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board complete all as specified.

S&F switch piano flush type 5/6 amps single pole one way complete all as specified.

S&F switch piano flush type 2 way 5/6 amps,230 volt single pole two way complete all as specified.

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified.

S&F of socket outlet 2 in 1, 5 Pin, 5/15 amp, multipurpose 230 volt flash type complete all as specified.

S&F switch piano flush type 15/16 amps single pole one way complete all as specified.

S&F Ceiling rose, surface type with back plate, three terminal /PVC/ polycarbonate, isolated body complete all as specified.

S & F lamp holder, isolated body, with back plate suitable for batten/angle fittings complete all as specified.

S & F deluxe fan electronic regulator 230 volts AC 50 Hzs rotary step white/ivory finish complete all as specified.

S&F, IP 20, class I, LED tube light fittings 18 W (or nearest next higher wattage) (4feet), wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified.

S & F in repair LED 10 W light fitting bulkhead with aluminium alloy grey cast iron powder coated housing, heat resistant prismatic glass cover with EPDM rubber lining including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as spedified and as directed.

S & F LED street light fittings 35 Watt ,230 VAC outdoor type with high pressure die cast aluminium housing, heat resistant, toughned glass cover with IP66 protection complete all as spedified and as directed.

S&F Sheet metal enclosure for vertical type TPN DB 4 way, double door incl hinged shutter and locking arrangemant for fixing for fixing DBs, flushed/ semi flushed/grouting on wall as per site requirement including DIN rail channel to mount MCBs with TPN bUs bar channel of rating 200 Amps and neytral link duly mounted on F class insulator with with colour coded heat shrinkable sleeves and powder coated paint after preparation of surfaces panel , including four pole MCCB 125 Amps (or higher) with blanking plates including provision of blanking plates as required and taking down the old one complete all as specified.

S&F Sheet metal enclosure for 8 way Distribution Boards (DB’s), double door, single pole & neutral with 200 amps rated bus bar, IP-20 protection suitable for fixing MCB"S/lsolators complete including provision of blanking plates as required and taking down the old one complete all as specified.

S&F MCB, Single pole & neutral 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

S&F MCB, Single pole, 6 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete including taking down the old one complete all as specified.

M &L for Earthing complete with GI earth plate electrode 600x600x6mm thick buried directly in ground (Earth pit not less than 2.25M deep below normal ground level) with top edge of the plate not less than 1.5m below normal GL. Connected to galvanized earth lead wire 4mm dia by means of nut, bolt, check nut and washers including necessary excavation and earth work in soft/loose soil, GI protection pipe light grade 15mm bore for protecting the GI wire mesh funnel alternate layer of charcoal dust, and salt PCC pit 1:3:6 type C1 using 20mm graded stone aggregate and 50mm thick RCC 1:2:4 type BO using 20mm graded stone aggregate cover re-inforced with 8 mm dia MS TMT bars 80mm C/C both ways complete all as specified and shown in Electrical plate No.3 SSR part-1 and connected to the earth point and testing complete including taking out the old one complete all as specified.

M&L for street light bracket made out of GI pipe light grade 32 MM dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling hole, fixing with runts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer complete all as specified.

Material and labour for concealed sub-main wiring alongwith earth wire of size of 2 x 4.0 sq. mm + 1 x 4.0 sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of of size not less than 25 mm with all fittings and accessories ISI marked including cutting chases for conduits & making good to walls, floors etc complete, including taking down old unsv aluminium submain wiring all as specified. NOTE : Two runs of 4 sqmm conductor for main and one run of 4 sqmm conductor as earth wire with proper colour coding including one run of PVC conduit shall be measured as one unit length. Connections of cables wit MCBs or bus bar shall be done through appropriate size brass/ copper thimbles complete all as specified.

Taking down ceiling fan/ exhaust fan sealing cable end, dismantling blades and removing fan blades to store complete all as specified.

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified.

Fixing only exhaust fan and connecting up including provision of cable from ceiling rose/connector to fan complete all as specified.

Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified.

Supply and lay in trenches/wall pipe galvanized, “Medium class”, including fittings 25 mm directed.

ALL as per item no. 133 but 40mm dia complete all as specified.

Supply and fix Gun metal gate Valves with iron wheel head of 25 mm dia bore complete with all accessories all as specified.

Excavation in trenches in soft/loose soil not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out for taking up / laying under ground electric cable complete with all accessories all as specified.

Returning, filling in, including spreading levelling watering and well rammming in layers not exceeding 25 cms in depth complete with all accessories all as specified.

Removing excavated materials n.exc 50m and depositing were directed at a level n.exc. 1.5m abive the starting level complete all as specified.

Removing Excavated soils exceeding 250 M but not exceeding 500 M and depositing complete all as specified.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 4 core all fixing and connecting accessories such as cable lugs, cable glands, nut, bolts, complete incl necessary taking out old unsv cable all as specified.

M&L for sand cushioning in cable trenches over & under the cable, with river washed coarse sand, as per standard practice with proper compaction complete all as specified. (Punned thickness 18 cm shall be considered for payment as per para 19.75 of SSR Part-I)

Supply and laying for brick protection for protection of cable over sand cushioning cables inside the trench by using common brunt clay building bricks sub-class “B” old size brick and flat and width wise along the axis of the trench complete all as specified.

M/S PLABAN KUMAR GOPE (BID ID -3118026)

Shri Amarnath Sah (BID ID -3123076)

R K AGARWAL (BID ID -3118065)

M/S S.K.DAS (BID ID -3118841)

M/S East India Traders (BID ID -3123142)

M/s. RAMPHAL GARG (BID ID -3120634)