BUDGETTED

No. Figure Amount

Civil works items

1 Excavation for foundation upto 1.50 mt depth including sorting out and 811.00 Cum 117.08

stacking of useful materials and disposing the excavated stuff for all lead

and lift for loose or soft soil.

2 Excavation for foundation depth from 1.5 mt. to 3.0 mt. including sorting 430.00 Cum 162.38

out and stacking of useful materials and disposing the excavated stuff for

all lead and lift for all sorts of soil.

3 Filling in foundation and plinth with sand in layers of 20 cm. thickness 94.00 Cum 460.19

including watering ramming and consolidating etc. complete.

cm thickness including watering, ramming and consolidation etc.

5 Applying general insecticide pest control treatment to floors, cupboards 345.00 Sq.m. 50.59

etc including labour material etc. complete. Using Imidacloprid 30.5 SC.

As Per 6113 Part -II (0.075% concentration by mass) is recommended

10.5ml chemical diluted with 5 liters of water application 0.5 liters

chemical/ sqm of surface is recommended as per I.S.

6 Providing and laying controlled cement concrete M-150 and curing 136.43 Cum 3784.60

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Foundations and plinth

7 Providing and laying controlled cement concrete M-250 and curing 209.50 Cum 4358.76

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Foundations, footings and

Mass concrete. Footing

8 Providing and laying controlled cement concrete M-250 and curing etc. 23.00 Cum 7362.90

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Columns upto plinth level.

9 Providing and laying cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 17.00 Cum 3195.28

machine cut stone aggregate 20 mm nominal size) and curing complete

excluding cost of form work in foundation and plinth.

10 Providing and laying controlled cement concrete M-200 and curing etc. 43.00 Cum 7327.55

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Columns for Ground floor.

11 Providing and laying controlled cement concrete M-200 and curing etc. 19.00 Cum 7366.94

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Columns for First floor.

12 Providing and laying controlled cement concrete M-250 and curing etc. 72.00 Cum 5819.62

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Ground and plinth beams.

13 Providing and laying controlled cement concrete M-150 and curing etc. 53.00 Cum 5064.14

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in plinth slab.

14 Providing and laying controlled cement concrete M-200 and curing etc. 49.00 Cum 6029.70

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Ground floor beams.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

15 Providing and laying controlled cement concrete M-200 and curing etc. 18.00 Cum 6069.09

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in First floor beams.

16 Providing and laying controlled cement concrete M-200 and curing etc. 51.50 Cum 6422.59

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Ground floor slab.

17 Providing and laying controlled cement concrete M-200 and curing etc. 12.00 Cum 6460.97

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in First floor slab.

18 Providing and laying controlled cement concrete M-200 and curing etc. 6.00 Cum 6620.55

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Chhajja for Ground floor.

19 Providing and laying controlled cement concrete M-200 and curing etc. 2.00 Cum 6659.94

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Chhajja for First floor.

20 Providing and laying controlled cement concrete M-200 and curing etc. 3.00 Cum 7416.43

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Lintel for Ground floor.

21 Providing and laying controlled cement concrete M-200 and curing etc. 1.00 Cum 7455.82

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Lintel for First floor.

22 Providing and laying controlled cement concrete M-200 and curing 6.00 Cum 6896.28

complete including the cost of form work but excluding cost of

reinforcement for reinforced concrete work in Staircase for Ground floor to

First floor.

23 Providing and fixing 90 cm high Stainless steel railing made from 10.00 Rmt. 5652.97

anticorrosive 304 grade S.S. pipe of 50 mm dia as hand rail with S.S.

grade baluster of 38 mm dia as a vertical support fixed in RCC slab at

1.2m c/c including three horizontal S.S. pipes of 25 mm dia at equal

distance fixed by 18.75 mm dia (16 gauge) S.S. pipe with baluster and

with 12 mm thick decorative toughen glass placed in between horizontal

support S.S. pipe including accessories as per detailed drawing as

directed etc. complete.

24 Providing I.S.I. Mark T.M.T. bar Fe-500D reinforcement for R.C.C. work 67955.00 Kg. 76.76

including bending, binding and placing in position upto all floor two level

for all floors.

25 Providing and laying brick work using common burnt clay building 82.00 Cum 4021.02

conventional type bricks having crushing strength not less than

Kg./Sq.cm. in foundation and plinth in cement mortar 1:6 (1 cement :

fine sand) including the cost of all materials and labour charges etc.

26 Providing and laying brick work using common burnt clay building 216.00 Cum 4289.33

conventional type bricks having crushing strength not less than

Kg/sq.cm. in super structure above plinth level upto floor two level in

cement mortar 1:6 (1 cement : 6 fine sand) for Ground Floor including the

cost of all materials and labour charges etc. complete.

27 Providing and laying brick work using common burnt clay building 92.00 Cum 4329.52

conventional type bricks having crushing strength not less than

Kg/sq.cm. in super structure above plinth level in cement mortar 1:6 (1

cement : 6 fine sand) for First Floor including the cost of all materials and

labour charges etc. complete.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

28 Providing and laying half brick work using common burnt clay building 35.00 Sq.m. 651.67

conventional type bricks having crushing strength not less than

Kg/Sq.cm in cement mortar 1:4 (1 cement : 4 coarse sand) in super

structure for Ground floor including the cost of all materials and labour

charges etc. complete.

29 Providing and laying half brick work using common burnt clay building 12.00 Sq.m. 657.67

conventional type bricks having crushing strength not less than

Kg/Sq.cm in cement mortar 1:4 (1 cement : 4 coarse sand) in super

structure for First floor including the cost of all materials and labour

charges etc. complete.

30 Providing 20 mm thick double coat mala cement plaster on interior brick / 852.00 Sq.m. 270.43

concrete work for plastering comprising of base coat of 12 mm thick

cement plaster in cement mortar 1:4 (1 cement : 4 coarse sand) in rough

finishing and 8 mm thick top coat of cement mortar 1:2 (1 cement :

coarse sand) finished with trowel including scaffolding, curing etc.

complete for Ground floor.

31 Providing 20 mm thick double coat mala cement plaster on interior brick / 428.00 Sq.m. 296.36

concrete work for plastering comprising of base coat of 12 mm thick

cement plaster in cement mortar 1:4 (1 cement : 4 coarse sand) in rough

finishing and 8 mm thick top coat of cement mortar 1:2 (1 cement :

coarse sand) finished with trowel including scaffolding curing etc.

complete for First floor.

32 Providing 10 mm thick smooth cement plaster in single coat for interior 395.00 Sq.m. 150.80

plastering on ceiling and soffits of stairs and finished even and smooth in

cement mortar 1:4 (1 cement : 4 sand) etc. complete for Ground floor.

33 Providing 10 mm thick smooth cement plaster in single coat for interior 196.00 Sq.m. 173.56

plastering on ceiling and soffits of stairs and finished even and smooth in

cement mortar 1:4 (1 cement : 4 sand) etc. complete for First floor.

34 Providing 20 mm thick double coat sand faced cement gutka plaster on 2026.00 Sq.m. 329.29

walls upto height 10 metres above ground level consisting of 12mm thick

backing coat of C.M. 1:3 (1-cement : 3 sand) and 8mm thick finishing coat

of C.M. 1:1 (1 cement : 1-sand) including 1cm x 1cm grooves etc.

35 Providing throating or plaster drip and moulding to R.C.C. Chhajja. 75.00 Rmt. 41.00

36 Applying two coats (white cement based) or acrylic lapy- putty & two coats 1831.00 Sq.m. 40.59

of primer of approved brand and manufacture on new wall surface to give

an even shade including thoroughly brushing the surface free from mortar

dropping and other foreign matter and sand papered smooth for all floors.

37 Wall painting (three coats) with plastic emulsion paint of approved brand 1242.00 Sq.m. 119.42

and manufacture on undecorated wall surface to give an even shade

including throughly brushing the surface free from mortar droppings and

other foreign matter and sand papered smooth.

38 Wall painting (three coats) with luxury plastic emulsion paint (Asian Royal 589.00 Sq.m. 124.68

or equivalent) of approved brand and manufacture approved by Engineer-

in-charge on undecorated Ceiling surface to give an even shade including

thoroughly brushing the surface free from mortar droppings and other

foreign matter and sand papered smooth.

39 Finishing wall with weather proof exterior acrylic emulsion paint with one 2024.00 Sq.m. 114.53

coat of primer on wall surface to give an required shape even shade after

thoroughly brushing the surface to remove all dirt, dust and remains of

loose powdered materials etc. complete for all floors.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

40 Providing and filling with good quality cinder (steam coal) as directed by 14.00 Cum 579.74

engineer in charge in sunks in layers of 15 cm thick including watering,

placing, ramming well etc. as directed for all floor.

41 Providing and laying controlled cement concrete M-200 for R.C.C. work 12.00 Cum 5705.49

and curing etc. complete including the cost of form work but excluding

cost of reinforcement for reinforced concrete work in Coping for Ground

42 Providing and laying controlled cement concrete M-200 for R.C.C. work 8.00 Cum 5744.88

and curing etc. complete including the cost of form work but excluding

cost of reinforcement for reinforced concrete work in Coping for First floor.

43 Providing and fixing FOUR TRACK SLIDING WINDOW having standard 24.00 Sq.m. 5946.88

extruded colour anodized aluminum Domal section of premium quality

(Jindal or equivalent) of frame size 136.00 mm x 50.00 mm x 1.5 mm and

shutters of size 65 mm x 27 mm x 1.5 mm with Interlock patti of size

mm x 29.25 mm x 1.4 mm with 5 mm thick transparent sun glass in

shutter with rubber gasket, one shutter with S.S Mosquito net jali with air

lock strip and end lock and finishing joints with silicon sealant, with

standard extruded colour anodized aluminum coated fittings & fixtures as

per details etc. complete for all floors.

44 Providing and fixing THREE TRACK SLIDING WINDOW having standard 4.00 Sq.m. 5651.96

extruded colour anodized aluminum Domal section of premium quality

(Jindal or equivalent) of frame size 80.00 mm x 45.00 mm x 1.5 mm and

shutters of size 65 mm x 27 mm x 1.5 mm with Interlock patti of size

mm x 29.25 mm x 1.4 mm with 5 mm thick transparent sun glass in

shutter with rubber gasket, one shutter with S.S. Mosquito net jali with air

lock strip and end lock and finishing joints with silicon sealant, with

standard extruded colour anodized aluminum coated fittings & fixtures as

per details etc. complete for all floors.

45 Providing and fixing TWO TRACK SLIDING WINDOW having standard 10.00 Sq.m. 4932.84

extruded colour anodized aluminum Domal section of premium quality

(Jindal or equivalent) of frame size 45mm x 45mm x 1.5 mm and shutters

of size 65 mm x 27 mm x 1.5 mm with interlock patti of size 36 mm x

29.25 mm x 1.4 mm with 5 mm thick transparent sun glass in shutter with

rubber gasket, one shutter with S.S. Mosquito net jali with air lock strip

and end lock and finishing joints with silicon sealant, with standard

extruded colour anodized aluminum coated fittings & fixtures as per

details etc. complete for all floors.

46 Providing and fixing standard extruded of alluminium section of size 63.50 8.00 Sq.m. 1525.00

x 38.10 x 1.95 mm, @ Wt 1.094Kg / Rmt with colour anodized alluminium

frame with 5 mm thick transparent bronze colour tinted float glass as

details etc. complete for fix window and Ventilation.

47 Providing & fixing in position standard extruded approved colour anodised 5.00 Sq.m. 2852.24

Aluminum Ventilator with outer frame 63.50 x 38.10 x 1.95 mm (@ Wt

1.094 kg/Rmt) with 3mm thick Bajari figure adjustable tinted louvers glass

fixed to alluminium strip blade including fixtures, fastening, labours and

equipments as per detailed drawing as directed. For Ventilators

48 Providing and fixing 50mm thick wooden door specially designed hollow 4.00 Sq.m. 6044.85

two flush door shutter made from teak wood frame of size 7.5cm x 3.8cm

with top, middle, bottom rails & vertical two styles & both side water proof

ply wood of 6 mm thick. Pivoted the double shutter with requires teakwood

batten with 1mm thick Premium Decorative lamination on both side, one

coat of primer & two coats of enamel paints on frame & edges, design of

which is to be approved by the architect. Door shall be providing with floor

spring and 60cm long stainless steel handle and necessary locking

system of Godrej, fixtures & fastenings etc. directed by engineer in

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

49 Providing and fixing 35 mm thick Flush door Single shutters, solid core 44.00 Sq.m. 5278.26

finished with requires teakwood batten around door including premium

Decorative 1mm thick lamination on both side, one coat of primer & two

coats of enamel paints on frame & edges, design of which is to be

approved by the architect. Door shall be providing with S.S. Aldrop,

hinges, stainless steel handle 15cm long, stopper and necessary locking

system of Godrej, fixtures & fastenings etc. directed by engineer in

50 Providing and fixing 15mm thick quartz white artificial marble counter for 6.00 Sq.m. 2831.03

basin including making necessary grooves in walls and jointing with

cement mortar 1:3 and adhesive of approved quality and full moulding the

edges with necessary labour & material etc. complete.

51 Providing and laying 32" x 32" Anti skid Glossy vitrified 8 mm thick tiles 219.00 Sq.m. 1640.24

flooring over 20 mm (average) base of cement mortar 1:6 (1 cement :

coarse sand) on new surface or fixing on existing flooring by adhesive

material including 4 mm thick groove and filling with colour epoxy groove

filling materials including finished with flush pointing & cleaning the

surface etc. complete as approved by Engineer in charge.

52 Providing and laying 32" x 32" vitrified 8 mm thick tiles in skirting, risers of 49.00 Sq.m. 1431.17

steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse

sand) by adhesive material including 4 mm thick groove and filling with

colour epoxy groove filling materials including finished with flush pointing

& cleaning the surface etc. complete as approved by Engineer in charge.

53 Providing and laying polished Kota stone slab flooring over 20mm 54.00 Sq.m. 976.72

(average) thick base of cement mortar 1:6 (1-cement : 6-coarse sand) or

L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and jointed with grey

cement slurry mixed with pigment to match the shade of slab including

rubbing and polishing etc. complete. (A) 25mm thick

54 Providing and laying polished kota stone slab 25mm thick in risers of 6.00 Sq.m. 1121.48

steps, skirting, dedo and pillars laid on 10mm thick cement mortar 1:3 (1

cement : 3 coarse sand) and jointed with gray cement slurry mixed with

pigment to match the shade of slab including rubbing and polishing etc.

complete. (A) 25mm thick

55 Providing & laying 600 mm x 600 mm Anti skid Matt finished tiles flooring 40.00 Sq.m. 1485.71

over 20 mm (average) base of cement mortar 1:6 (1 cement : 6 coarse

sand) on new surface and jointed with color cement slurry including finised

with flush pointing & cleaning the surface etc. complete for antiskit.

56 Providing & laying 1200 mm x 600 mm G.V.T. glazed / glossy tiles 8 to 10 224.00 Sq.m. 1609.94

mm thick in skirting, risers of steps and dedo on 10mm thick cement

plaster 1:3 (1-cement : 3 coarse sand) on new surface with 4 mm spacer

and epoxy filling & cleaning the surface complete as per detail approved

by Architect/ Engineer in charge.

57 Providing and laying machine cut free edge machine polished Granite 16 13.00 Sq.m. 2657.31

to 18 mm thick finished treads and risers 1cm projecting, nozing rounded

moulding in tread laid over 12 mm (av.) thick bases of cement mortar 1:3

(1-cement : 3-coarse sand) jointed with grey or colour cement slurry

including rubbing and polishing including making three Nos. of grooves of

size 3mm x 3mm along the length of treads etc. complete

58 Providing and fixing precast rubber Dye / steel Dye inter locking concrete 909.00 Sq.m. 686.90

block 60mm thick with grade of concrete M-300 pneumatic compressed /

vibrated mechanically and as per approved design confirming to IS

: 2006 including 35 mm sand layer for levelling and filling the joint with

sand in proper line and level as per guidlines of IRC : SP 63-2018 etc.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

59 Providing and laying broken china mosaic flooring for terrace using 12 mm 387.00 Sq.m. 747.29

to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3

to plain or slope and to be tempered to bring mortar creme out upto

surface using white cement including rounding off junctions and extending

them upto 15 cm along the wall, clearing with water and oxalic acid etc. as

60 Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-coarse 426.00 Sq.m. 330.88

sand : 4-graded stone aggregate 20mm nominal size) laid in one layer

and finished with a floating coat of neat cement. (B) 50mm thick.

61 Providing and fixing mirror polished 16 to 18 mm thick Granite stone with 108.26 Sq.m. 2477.53

full round edge and polished of approved quality in cladding on sill and

around the doors / windows / ventilation with 20 mm thick cement plaster

C.M. (1:4) and fixing with cement slurry & adhesive including moulding of

exposed edges as directed by engineering in charge etc. complete.

62 Providing and fixing Safety grills of required pattern for windows / Door 1520.00 Kg. 106.05

using necessary 16mm dia. M.S. pipe, M.S. flats and other structural steel

at required spacing including cutting, welding and fabrication etc. including

one coat of primer of approved quality and two coats of oil painting as per

detail drawing etc. complete.

63 Providing, erecting and fixing double coated PVC (I.S.I.) water tank of 7000.00 Litre 3.95

required capacity each with all necessary fittings and connection etc.

complete on terrace as directed.

64 Providing, laying and jointing in true line and level I.S.I. mark 50mm dia. 80.00 Rmt. 195.67

U.P.V.C. Pipe (SCH- 40) for cold water including fittings as approved by

Engineer in charge. Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concealed as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

65 Providing, laying and jointing in true line and level I.S.I. mark 40mm dia. 60.00 Rmt. 148.12

U.P.V.C. Pipe (SCH- 40) for cold water including fittings as approved by

Engineer in charge. Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concealed as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

66 Providing laying and jointing in true line and level I.S.I. mark 25mm dia. 60.00 Rmt. 91.84

U.P.V.C. Pipe (SCH- 40) for cold water including fittings as approved by

Engineer in charge. Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concealed as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

67 Providing laying and jointing in true line and level I.S.I. mark 15mm dia. 42.00 Rmt. 72.65

U.P.V.C. Pipe (SCH- 40) for cold water including fittings as approved by

Engineer in charge. Pipe shall be fixed on the wall with the help of clamp

at every two metre C/C or shall be concealed as directed including

necessary fittings etc. including testing of pipe and joints and fixing the

same with adhesive solvent, including cost of all materials.

68 Providing, laying and jointing in true line and level I.S.I. mark 160mm 45.00 Rmt. 831.22

diametre U.P.V.C (Type B) conforming to IS 13592-1992 with one end

plain and other end socketed with rubber ring, & fittings conforming to ISI

14735-1999 of approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 160 mm diametre x 210 mm length x

mm heigh at every 2000 mm center to center or shall be concealed in

walls as directed including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

69 Providing, laying (to level or slopes) and jointing reinforced concrete Light 35.00 Rmt. 665.48

duty non-pressure pipes I.S. class NP2 of the following internal diameter

with collars and butt ends prepared for collar joints including testing of

joints complete. (D) 300mm

70 Providing, laying and jointing in true line and level I.S.I. mark 110mm 70.00 Rmt. 835.15

diametre U.P.V.C. (Type B) conforming to IS 13592-1992 with one end

plain and other end socketed with rubber ring & fittings conforming to ISI

14735-1999 of approved make for drainage system pipe line, pipe shall

be jointed with each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 110 mm diametre x 149 mm length x

mm heigh at every 2000 mm center to center or shall be concealed in

walls as directed including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

71 Providing, laying and jointing in true line and level I.S.I. mark 75mm dia. 36.00 Rmt. 315.12

U.P.V.C. SWR Type-B conforming to IS 13592-1992 with one end plain

and other end socketed with rubbering and fitting conforming to ISI 14735-

1999 of approved make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant, pipe shall be fixed on wall

using of PVC clamp at every 2000 mm c/c or shall be concealed in walls

as directed including necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed with adhesive solvent

cement including cost of all materials.

72 Providing and fixing in PVC SWR cowel went to pipes. (B) 75mm dia. as 3.00 No. 15.66

73 Providing and fixing in PVC SWR cowel went to pipes. (C) 110mm dia. as 10.00 No. 28.79

74 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm 12.00 No. 558.36

diameter with jali of the following nominal diameter of self cleansing

design with C.I. screwed down or hinged grating including the cost of

cutting and making good the walls.

75 Providing and fixing white vitreous china Wall hung water closet of size 4.00 No. 26471.09

360 x 490 x 330 mm of approved shape (Premium quality) including

Metropole flush system including UF soft close slim seat cover, hinges,

hand shower (Health Faucet) with 1 meter long easy flex tube in chrome

finish & Wall hook, Paper holder with flap recessed type, fixing

accessories, accessories set and cistern fittings, with specials of standard

make and mosquito proof coupling of approved design complete, cutting

and making good the floors wherever required including jet spray as

directed by EIC.

76 Providing and fixing water closet squatting pan (Indian type W.C. Pan) 1.00 No. 1541.26

size 580mm with P or S trap including jointing the trap with soil pipe in

cement mortar 1:1 (1 cement : 1 fine sand) with connection pipe, flush

cock with wall flange with all fitting inlet and outlet connection etc.

completed as per directed engineer in-charge.

77 Providing and fixing ball cock of approved quality as directed. (A) Copper 2.00 No. 189.84

Metal (ii) 50mm dia.

78 Providing and fixing of first quality white vitreous china Table Top Basin, 5.00 No. 8514.30

type wash basin as per product detail,including filling gap between counter

and wash basin with approved sanitary grade material, cutting and making

good the walls where required to the complete satisfaction of the Engineer

in charge including Oval Wash basin, Rag Bolts for Wash Basins, Bottle

Trap, Waste Coupling, Prismatic Pillar cock. Size 550 x 440 x 155mm

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

79 Providing and fixing 6 mm thick decorative mirror including machine 3.00 No. 2525.00

polishing glass all over and fixed with S.S. studs etc complete with all

required fittings & fixtures.

80 Providing and fixing towel rack of 600mm length, in polished chrome with 5.00 No. 2923.95

concealed type brackets, fixed to the wall with C.P. brass screw etc.

complete with all fittings as per specification of approved make and

conforming to manufacturers standards as directed by EIC.

81 Providing and fixing 2 Way Bib Cock (premium quality) with wall flange in 8.00 No. 3127.97

polished chrome of approved quality and conforming to manufacturers

standards as directed by EIC.

82 Providing and fixing Towel Ring Square with round flange - polished 8.00 No. 1472.58

chrome (premium quality) with concealed type brackets, fixed to the wall

with C.P. screws etc. complete with all fitting as per specifications of

approved make and conforming to manufacturers standards as directed

83 Providing and fixing in position 300 mm high, 150 mm wide English letters 30.00 No. 707.00

made from 1.0 mm thick stainless steel sheet as directed by Engineer in

charge with all necessary tools & plants etc. complete.

84 Providing and fixing single lever high flow bath mixer with concealed body 5.00 No. 12279.58

diverter (premium quality) with wall flange in polished chrome of approved

quality and conforming to manufacturers standards as directed by EIC.

85 Providing and fixing Angle Cock (premium quality) with wall flange in 17.00 No. 1390.77

polished chrome of approved quality and conforming to manufacturers

standards as directed by EIC.

86 Providing and fixing S.W. Gully trap with C.I. grating brick masonry 5.00 No. 1246.92

chamber and water tight C.I. cover with frame of 300 mm x 300 mm size

(inside) with standard weight. [i] square mouth trap (B) 150 mm x 100 mm

size P or R type

87 Constructing brick masonry chamber for underground C.I. Inspection 16.00 No. 3172.41

chamber and bends with bricks having crushing strength not less than

Kg./Cm2 in C.M. 1:5 precast RCC cover 455mm x 610mm internal

dimensions with frame (R.C.C. top slab with 1:2:4 mix (1-cement :

coarse sand : 4 graded stone aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed concrete etc.

complete (i) Inside dimensions 455mm x 610mm and 450mm deep for

single pipe line.

88 Constructing brick masonry chamber for underground C.I. Inspection 16.00 No. 3883.45

chamber and bends with bricks having crushing strength not less than

Kg/Cm2 in C.M. 1:5 precast RCC cover 500mm x 700mm internal

dimensions with frame (R.C.C. top slab with 1:2:4 mix (1-cement :

coarse sand : 4 graded stone aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement mortar 1:3 finished smooth

with a floating coat of neat cement on walls and bed concrete etc.

complete (i) Inside dimensions 500mm x 700mm and 450mm deep for

single pipe line.

89 Extra over items for every additional depth of 0.1M. of part thereof beyond 15.00 No. 242.39

450mm depth for brick masonry chamber. (i) for 455mm x 610mm size.

90 Extra over items for every additional depth of 0.1M. of part thereof beyond 15.00 No. 264.86

450mm depth for brick masonry chamber. (ii) for 500mm x 700mm size.

91 Providing cement vata (10 cm x 10 cm size) quarter round in cement 44.00 Rmt. 23.68

mortar 1:1 including neat cement finishing, watering etc. complete.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

92 Providing and fixing MS Ladder of required pattern with MS flats (30 x 400.00 Rmt. 112.11

3mm) or round or square bars (12mm) at required spacing & with round

headed bolts and nuts or screws or welding including primer coat of

approved quality and two coats of oil paint as directed by engineer in

93 Providing and fixing Soap Dish Holder - Chrome (premium quality) with 5.00 No. 1210.99

wall flange in polished chrome of approved quality and conforming to

manufacturers standards as directed by EIC.

94 Providing and fixing stainless steel kitchen sink of Glossy ASIS 304 grade 2.00 No. 7493.19

x 1mm thick with over all size 485 x 410 mm and bowl size 410 x 365 x

165 of approved make with M.S. or C.I. brackets painted white including

Single Lever Sink Mixer (premium quality) cutting holes and making good

the walls and floors wherever required with 32 mm dia. C.P. brass waste

coupling, single lever sink mixer and M.I. fisher union etc. complete as

directed by engineer incharge.

95 Constructing Sandwitch Platform of 16 mm-18 mm thick Polished Black 8.00 Sq.m. 5373.05

Granite at top and 25 mm thick Kota stone slab one side polished at

bottom with cementing materials / adhesives including making necessary

grooves in walls with vertical sandwich two Kota stone 25 mm support

every 60 cm centre to centre covered with granite patti or as required

including all labour material of approved quality including full moulded

round front edge granite strip of one side polished and jointed with grey

cement slurry including rubbing and polishing etc. complete for all floors.

96 Steel work, welded in built up sections framed work including cutting, 62.86 Qtl. 9047.86

hoisting, fixing in position and applying a priming coat of red lead paint

and two coats oil paint. (A) In beams and joists, channels angles Tees,

flats, with connecting plates or angle cleats as in main and cross beams.

Hip and jack rafters, purlins connected to common rafters and the like.

97 Providing and fixing Overhead slim Shower Square Shape Single Flow 5.00 No. 5246.95

(premium quality) of approved quality and conforming to manufacturers

standards as directed by EIC. 150 x 150 mm

98 Providing and fixing push button Soap Dispensers (premium quality) of 6.00 No. 1356.43

approved quality and conforming to manufacturers standards as directed

99 Providing and fixing Tumbler Holder - Chrome (premium quality) of 7.00 No. 1240.28

approved quality and conforming to manufacturers standards as directed

100 Providing and fixing Tile Insert waste water floor drain with Anti cockroach 4.00 No. 1270.58

trap of approved quality and conforming to manufacturers standards as

directed by EIC. Size 5 x 5 inch (premium quality).

101 Providing and fixing premium quality Tile Insert waste water floor drain 4.00 No. 4638.93

(premium quality) with Anti cockroach trap of approved quality and

conforming to manufacturers standards as directed by EIC. Size 24 x

102 Providing and fixing 6 mm thick Lexan Polycarbonate multi wall roofing 59.00 Sq.m. 1441.90

sheet fixed with hilti screw and rubber silicon sealer and alluminium strip

of size 50 x 3 mm etc. complete as directed by Engineer in charge.

103 Providing and fixing Sliding Pleated Mosquito net having standard 8.00 Sq.m. 2869.41

extruded colour anodized aluminum section of premium quality of section

size top and bottom of 50.8 mm x 25.4 mm x 2.0 mm and both side

section of 63.50 mm x 25.4 mm x 2.00 mm with collapsible Mosquito net

with magnet locking system etc complete as directed by EIC.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

104 Excavation for foundation for depth from 3.0 mt. to 5.0 mt. including 9.00 Cum 174.23

sorting out and stacking of useful materials and disposing off the

excavated stuff upto 50 Meter lead. (B) Dense or Hard soil.

105 Providing and laying controlled cement concrete M-200 and curing 13.00 Cum 6611.46

complete including the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in (B) Walls, from top of

foundation level upto floor two level.

106 Providing and laying white glazed tiles 6mm thick in skirting, risers of 87.00 Sq.m. 946.50

steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3 coarse

sand) and jointed with white cement slurry.

107 Providing and fixing C.I. Manhole cover 0.60 M. x 0.45M. size having 1.00 No. 958.17

weight not less than 35 Kg.

108 Providing and fixing rolling shutters of approved make made of 80 mm 5.00 Sq.m. 3503.41

wide M.S. laths inter-locked together through heir entire length and jointed

together at the ends by end locks mounted on specially designed pipe

shaft with bracket plates, guide channels and arrangement for inside and

outside locking with push-pull operation including the cost of hood cover

and sprig etc.complete (A) Shutters having width below 3.5 mt.

109 Providing and fixing to wall, ceiling and floor 10.0 Kg. F/Cm2 working 90.00 Rmt. 336.24

pressure polythene pipes of the following outside dia. Low density,

complete with special flange compression type fittings, wall clips etc.

including making good the wall ceiling and floor. (G) 110 mm dia.

110 Providing and fixing to wall, ceiling and floor 10.0 Kg. F/Cm2 working 10.00 Rmt. 696.90

pressure polythene pipes of the following outside dia. Low density,

complete with special flange compression type fittings, wall clips etc.

including making good the wall ceiling and floor. (H) 160 mm dia.

111 Providing junction for rain water junction chamber of size 0.60 x 0.60 x 1.00 No. 8734.48

0.75m with excavation of size 1.96 x 1.96 m & 0.15m thick C.C. 1:2:4 bed

concrete including brick masonary wall in C.M. 1:6 of 0.75m height &

0.23m thick with 15mm thick cement plaster inside & outside & 1.06 x

RCC (1:2:4) slab of thickness 0.15m with CRS steel and 0.60m x 0.45m

cast iron manhole cover with frame weight not less than 35 kg as per

directed by Engineer-in-charge

112 Providing filter chamber of brick work in C:M 1:6 of size 2.06m x 1.20m 1.00 No. 15478.25

x1.20m & excavation dimension of 2.66m x 1.81 x 1.35m including C.C

1:2:4 bed concrete of 0.15m thick including brick work in C.M. 1:6 for

23cm thick wall including 15mm thick cement plaster inside & outside with

cement slurry & 10cm thick RCC 1:2:4 top cover with frame of minimum

weight of 35 kg & filling filter material kapchi in layers (25-40mm & 10-

20mm) & B.T. metal 40mm & sand as per directed by Engineer-in-charge.

113 Providing Recharging pit of size 2.0m dia. & 2.0m depth of water logging 1.00 No. 93591.65

with excavation filling the pit with gravel & sand in layers including making

200 mm dia. bore depth of 80.0 mt & above concrete with kapchi in layers

(20-40mm & 10-20mm) & BT metal 40mm & filling brick as directed by

Engineer-in-charge.

114 Providing and laying cement concrete 1:3:6 (1-Cement : 3 Coarse sand : 56.40 Cum 3168.26

6 graded B.T. stone aggregate 40 mm normal size) and curing complete

including cost of formwork in foundation and plinth.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

115 Providing and fixing of Ridge flashing for roof panel shall be made out of 54.00 Sq.m. 858.67

0.5 mm thick precoated G.I. sheet. The Precoated sheet shall be of

minimum 240 mpa steel grade confirming to IS 14246:1995 and shall

have zinc coating of minimum 120 gsm as per IS:277:1992, 5-7 microns

epoxy primer on both side of the sheet and polyester top coat 15-18

micron. The PPGI sheet shall have plastic protective guard film of

minimum 25 microns to avoid scratches during transportation. The ridge

shall be fixed to the steel members by pop rivet or self drilling/self stitching

fasteners @ maximum 450 mm c/c along length of capping / flashing etc.

116 Design, Supply and installation of Safety Signage made of Zinc Sulphilde 1.35 Sq.m. 3787.50

based glow in dark, Rigid sheet with High Luminous property enclosed in

a transparent weather proof UV stabilized plastic pasted on 3 mm thick

clear acrylic sheet such as EXITS, EMERGENCY EXIT, DO NOT USE

LIFT DURING FIRE, FLOOR MARKINGS, FIRE LIFT, STAIRCASE EXIT,

FIRE ALARM CALL POINT, FIRE HOSE REEL, FIRE HYDRANT POINT

etc. complete.

117 Supply, filling and fixing of approved make ABC type fire extinguisher - 6 2.00 No. 2828.00

Kg. capacity as per IS:15683 & IS :

118 Supply, filling and fixing of approved make CO2 type fire extinguisher. 2.00 No. 6716.50

Capacity 4.5 Kg. (conforming to IS-15683)

119 Drilling of 165 mm dia. bore in over burden strata and further drilling of 80.00 Rmt. 313.10

165mm dia bore in all types of strata with DTH ring including lowering of

casing pipe up to required length and testing etc. including testing with

ben meter.

120 Providing and lowering of 165mm FVPVC pipe zero to overburden strata. 65.00 Rmt. 536.57

121 Providing and lowering 165 mm dia. PVC pipe etc. complete. 15.00 Rmt. 252.50

122 Providing and fixing M.S. cap plug hinge type with frame of required 1.00 No. 165.64

design for 150mm dia. bore casing pipe.

123 Supplying and installing submersible pumping set 7.50 HP manufactured 2.00 Set 26300.40

as per IS standard including non return valve sluice valve flexible cable

(as required 70 mtr length) volt meter, panel board, capacitor, starter,

switch, pressure guage with accessories of approved manufacture tools of

50 Hours power capacity.

124 Providing and fixing check or non return fully wheel valve of 50 mm 2.00 No. 1111.00

125 Providing and fixing to wall, ceiling and floor galvanized mild steel tubes 100.00 Rmt. 787.40

(medium grade) of the following nominal bore, tube, fittings and clamps

included making good the wall, ceiling and floor (F) 50 mm

126 Providing 15mm thick cement plaster in single coat on rough (similar) side 121.00 Sq.m. 215.24

of single or half brick walls / concrete wall for interior plastering and

finished even and smooth in C.M. 1:4 (1 cement : 4 coarse sand) with

floating coat of neat cement slurry etc. complete for Ground floor.

127 Constructing brick masonry chamber for underground C.I. Inspection 10.00 No. 7180.44

chamber and bends with bricks having crushing strength not less than

Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light duty) 455mm x 610mm

internal dimensions, total weight of cover with frame to be not less than

38Kg. (Wt. of cover 23 Kg.) and Wt. of frame 15 Kg.) (R.C.C. top slab with

1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm

size) foundation concrete 1:5:10 inside plaster 15mm thick with cement

mortar 1:3 finished smooth with a floating coat of neat cement on walls

and bed concrete etc. complete. (iii) Inside dimensions 600mm x 850 mm

and 450mm deep for pipe lines with three or more inlets.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

128 Providing, laying (to level or slopes) and jointing reinforced concrete Light 30.00 Rmt. 1060.59

duty non-pressure pipes I.S. class NP2 of the following internal diameter

with collars and butt ends prepared for collar joints including testing of

joints complete. (E) 450mm

129 Constructing Manhole with R.C.C. top slab in 1:2:4 mix (1 cement : 2- 5.00 No. 11029.97

coarse sand : 4-graded stone aggregate 20mm nominal size) foundation

concrete 1:3:6 mix (1-cement : 3- coarse sand : 6 Brick bats 40 + 50mm

size) inside plastering 15mm thick with Cement Mortar 1:3 (1-Cement : 3-

coarse sand) finished with a floating coat of neat cement and making

channels in cement concrete 1:2:4 mix (1-Cement : 2-Coarse sand :4-

stone aggregate 20mm nominal size) finished smooth complete including

curing and fasting (i) Inside size 900mm x 1200mm and 1.5M. deep

including C.I. cover with frame size 560mm diameter total weight of cover

and frame to be not less than 128 kgs. (Wt. of cover 64 Kg. and Wt. of

frame 64 Kg.) (A) With 230mm thick walls of brick masonry using brick

having crushing strength not less than 35Kg. / Sq.cm. in Cement Mortar

1:5 (1 cement : 5 coarse sand) (1) A type depth 0.90 Metre for 150mm

diameter sewer.

130 Box cutting the road surface to proper slope and camber for making a 367.00 Cum 104.20

base for road work including removing the excavated stuff and depositing

on the road side slope as directed upto 50 Mt.lead.

131 Construction of 150 mm thick compacted granular sub base (Grade-V, 187.00 Cum 1003.94

Crushed B.T. materials of 53 mm to 26.5 mm @ 35%, 26.5 mm to

mm @ 50%, below 2.36 mm @ 15%) by providing close graded material,

mixing in a mechanical mix plant at OMC, carriage of a mix material to

work site, spreading uniform layers with motor grader on prepared

surface and compacting with vibratory power roller to achieve desire

density, complete clause as per

132 Providing, laying, spreading and compacting graded stone aggregate to 54.00 Cum 1059.49

wet mix macadam specification including premixing the material with water

at OMC in mechanical mix plant carriage of mixed material by tipper to

site, laying in uniform layers with paver in sub-base / base course on well

prepared surface and compacting with vibratory roller to achieve the

desired density.

133 Compaction and finishing of cement concrete road by Trimix M-250 450.00 Sq.m. 63.63

process providing extra labour charges for the trimix vacume dewatering

service process on cement concrete road surface by using vacuum

dewatering pump floater surface vibrator including making grooves and

rough finish to surface including leveling etc. complete.

134 Providing and laying homogeneous grey cement based concrete kerbing 620.00 Rmt. 361.64

of size 30 cm x 30 cm x 10 cm size as per detailed drawing having grade

of concrete M-25 grade, including necessary excavation, BBCC 1:5:10,

7.5 cm as per detailed drawing fixing in line and level, filling joints in C.M.

1:3 with smooth finished, white washing three coats etc. complete as

directed by Engineer in charge.

135 Constructing providing and fabricating cattle guard using channel section 8.00 Sq.m. 4785.38

frame of size ISMC series 100 mm x 50 mm (Weight 9.20 kg/Rmt) and

ISMC section 100 mm x 75mm (weight 11.50 kg/Rmt) intermediate

support for welding G.I.pipe at 12 Cm C/C of size 50 mm in a frame made

of channel section size 100 mm x 50 mm all round including fixing the unit

on prepared chamber of masonary wall using MS hold fast embeded in

masonary wall top as directed by Engineer in charge and as per drawing

and necessary required arrangement etc complete.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

136 Providing and fixing decorative entrance gate made out of cast iron and 1688.00 Kg. 165.64

various mild steel tabular section combination, the ornamental entrance

gate should be fixed at compound wall including pattern and die making,

cutting, welding, grinding, fabrication, fixing in position at compound wall

with necessary pedestal, bearing block and other locking arrangement.

The entrance gate should be painted with two coats of priming coat of

paint and two coat of oil paint etc. complete as per detail design and

instruction of architect.

137 Providing and fixing concertina coil fencing with punched tape concertina 205.00 Rmt. 460.56

coil 600 mm dia 10 mt openable length having 50 no rounds per 6 mt

length, upto 3mt height of wall with existing angle iron (50mm x 50mm x

5mm) required shaped as per directed Engineer in charge. placed 2.4mt

or 3.00mt a part and with 4 horizontal R.B.T. reinforced barbed wire (3

mm), stud tied with G.I. staples and G.I. clips to retain horizontal, including

necessary bolts or G.I. barbed wire tied to angle iron, all complete as per

direction of Engineer-in-charge, with reinforced barbed tape (R.B.T.) /

Spring core (2.5 mm thick) and weight 43.478 gm/meter at compound wall

for ESR M4/ intakewell.

138 Applying priming coat over new steel and other metal surface after and 23.00 Sq.m. 98.72

including preparing the surface by throughly cleaning, oil, grease, dirt and

other foreign matter and scoured with brushes fine steel wood, scrapers

and sand paper with ready mixed priming paint brushing red lead and

painting two coats on new steel and other metal surface with synthetic

enamel paint, brushing to give an even shade including cleaning the

surface of all dirt, dust and other foreign matter.

139 Dismentaling doors, windows, ventilators etc. (wood or steel) shutters 41.00 No. 182.94

including chowkhats architraves, holdfasts and other attachment etc.

complete and stacking them within all lead and lift. (i) Not exceeding

Sq.m. in area.

140 Dismantling tiled of stone floors laid in mortar including stacking of 514.77 Sq.m. 46.77

serviceable materials and disposal of unserviceable materials with all lead

141 Demolition including stacking of serviceable materials and disposal of 129.58 Cum 1030.81

unserviceable materials with all lead and lift (i) R.C.C. work.

142 Demolition of brick work and stone masonary including stacking of 354.30 Cum 536.09

serviceable materials and disposal of unservieable materials with all lead

and lift. (ii) in cement mortar

143 Dismentaling steel work including distempering and stacking the materials 10951.20 Kg. 3.67

with all lead and lift.

144 Dismentling C.I. pipes, G.S.W. pipes and A.C. rain water pipes with fittings 69.90 Rmt. 73.02

and clamps including stacking the materials with all lead and lift.

145 Dismentling sanitary fittings like wash basin, W.C. pan Indian and 11.00 No. 394.51

European type, flushing tank etc. including stacking the materials with all

lead and lift.

146 Dismentling wood work, wrought framed and fixed in frames trusses 0.34 Cum 1711.65

including stacking the materials with all lead and lift.

Electrical Items

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

147 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm 107.00 Pt. 485.81

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in below type of pipe erected with

6A Modular type switch / bell push & accessories and earth continuity of

following type, erected on PVC / Metallic / Wooden box, single mounting

base frame covered with textured / metallic / white front plate modules

erected on / in wall / ceiling as per pipe erected, with necessary Lamp

holder / ceiling rose / H.D. Connector as directed. (f) with medium class

Rigid PVC pipe and accessories erected concealed in wall / ceiling

complete. Cat-III

Point wiring for Light Point in Bath & W/C .Cat-III 15.00 Pt. 242.91

148 Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) 28.00 Pt. 674.68

both are of ISI marked 1.1 KV Grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type electronic fan regulator

mounted and accessories with earth continuity of following type erected

on PVC / Metallic/Wooden box, single mounting base frame covered with

textured / metallic / white front plate modules erected on / in wall / ceiling

as per pipe erected. with necessary ceiling rose / H.D. Connector as

directed. (f) with medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat-III

149 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin 29.00 Pt. 257.55

socket erected on PVC / Metallic/Wooden box, single mounting base

frame covered with textured / metallic / white front plate modules erected

on / in wall / ceiling with following type accessories. Cat-III

150 Providing following type of Modular Type Accessories mounted with PVC / 17.00 Nos. 151.50

metallic / Wooden box, single mounting base frame covered with textured

/ metallic / white front plate, modules erected with necessary connections

as per site situation directed by Engineer In charge. (1) One No. SP

Amp. Cat-III

(2) One No 5 pin plug.Cat-III 17.00 Nos. 151.50

(4) TV Co-axial Socket outlet .Cat-III 2.00 Nos. 160.59

(7) Blank Plate Single.Cat-III 1.00 Nos. 25.25

(8) Computer RJ-45 socket Cat-III 14.00 Nos. 160.59

(9) 16 Amp. SP one way switch.Cat-III 13.00 Nos. 180.79

(10) 6/16Amp. Universal socket Cat-III 21.00 Nos. 199.98

(14) 6A/ 10A/ 16A/ 20A/ 25A/ 32A Double Pole Modular MCB Switch Cat- 8.00 Nos. 410.06

151 Providing and erecting ISI mark Medium class RIGID PVC PIPES of 470.00 Mtr. 33.33

following size complete to be erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed with adhesive solution &

clamps with following dia of pipes, in approved manner as directed. (b)

152 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 255.00 Mtr. 62.62

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in / flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size. (a) with medium class Rigid PVC pipe and

accessories.(a) 2 wire 1.5 sq.mm

(b) 2 wire 2.5 sq. mm 645.00 Mtr. 82.82

153 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI 160.00 Mtr. 112.11

marked stranded Copper conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth continuity of following

size (a) with medium class Rigid PVC pipe and accessories (a) 2 wire

(b) 2 wire 6 sq. mm 30.00 Mtr. 147.46

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

(h) 4 wire 6 sq. mm 145.00 Mtr. 260.58

154 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 250.00 Mtr. 46.46

kv grade ISI marked copper wires of following size to be erected as

directed.(e) 1.50 Sq.mm 3 core round PVC sheathed.

155 Providing & erecting approved make following size of TV Co-axial flexible 120.00 Mtr. 39.39

cable comprising inner conductor of solid bare copper insulated with

Foam PE & Secondary conductor made of poly - Aluminium film bonded

Al. Braids @ suitable coverage overall sheathed with black PVC

insulation. (b) RG-6

156 Supplying & erecting approved make Telephone Cable electrolytic copper 200.00 Mtr. 20.20

conductor PE insulation twisted in two pairs & wrapped with FRLS PVC

tape & sheathed with FRLS PVC or HFFR outer Jacket suitable for

telephone wiring & confirming to C-DOT erected in existing pipe of

following size of conductors & nos.of pairs with necessary connections. [A]

Conductor Size 0.5 mm.(a) Unarmoured. (2) Two Pairs

157 Supplying & erecting approved make LAN cable of following size in 350.00 Mtr. 47.47

existing pipe as per direction. [C] CAT -

158 Providing & erecting Switch board for Computer or electric apparatus 14.00 Nos. 1133.22

consisting of following modular type accessories mounted with PVC /

Metallic concealed/open box with single mounting base frame covered

with textured / metallic / white front plate, modules erected with necessary

connections as directed. 1 no. 6A/16A universal plug-switch combined.

nos. 6A Switch, 3 nos. 6A 5 pin Plug [B] For Modular Type Accessories

159 Decorative call bell Ting-tong box type 250 volts complete erected. 2.00 Nos. 71.71

160 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt Nos.

to 0.5 Watt assembled on single MCPCB, with housing used as a heat

sink shall be made of thick sheet steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high U.V. & corrosion resistance

with diffuser with company mark/name 160V to 270V, Power Factor more

than 0.95, THD < 15%, CCT 3000 K to 6500K, Luminaire efficacy>

lumens/watt, LED driver efficiency > 85% (fitting required LM-79 & LM-80

Certificates) (NOTE: Below description have shown ranges of Wattage

capacity between the ranges shown) (A) Tube Light with integral driver.

(iv) 22-24 Watts, Surge - 2KV, IP-20, conventional 4 feet Cat-III

(v) 36 Watts, Surge-2 KV, IP-20, conventional 4 feet Cat-III (Contractor 13.00 Nos. 535.30

will have to bound for the replacment warranty for 3 years incase of any

deffect. There has been also special condition provided in the tender

form in this regard)

161 Supplying and erecting led lamps with following wattage capacity of 220 to 4.00 Nos. 112.11

240 voltage, minimum 15000 burning hours life, 500 V in built,

surge,protection,Polycarbonate diffuser, mounting suitable for E14 / E27 /

B22 lamp holders, pf >= 0.5 (A) LED Lamps integral type, with PC diffuser

suitable LAMP holder. (ii) 8 watts Cat-III (Contractor will have to bound for

the replacment warranty for 3 years incase of any deffect There has been

also special condition provided in the tender form in this regard).

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

162 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt 90.00 Nos. 758.51

to 0.5 Watt assembled on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast powder coated and high U.V. &

corrosion resistance with diffuser housed in aluminium casted body with

company mark/name 160V to 270V, Power Factor more than 0.95, THD <

15%, CCT 3000 K to 6500K, Luminaire efficacy> 85 lumens / watt, LED

driver efficiency > 85% (fitting required LM-79 & LM-80 Certificates)

(NOTE: Below description have shown ranges of Wattage capacity of LED

the ranges shown) (A) Square/ Circular shaped Surface / Recessed

Mount Downlight with provision for spring loaded mounting clips complete.

IP20. (iv) 22-24 watts, Surge-2 KV Cat-III (Contractor will have to bound

for the replacment warranty for 3 years incase of any deffect. There has

been also special condition provided in the tender form in this regard).

(B) LED Panel Light with provision for Plane front frame with translucent 5.00 Nos. 1794.77

cover fixed to housing complete.IP20 (vi) 36 watts, 24" x 24", Surge-

2KV.Cat-III (Contractor will have to bound for the replacment warranty for

3 years incase of any deffect There has been also special condition

provided in the tender form in this regard).

163 Supplying and erecting LED street light / Flood light fittings with High 40.00 Nos. 4997.48

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder coated and heat

sink extruded aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or embossed

160 to 270 V, Power Factor more than 0.95, THD < 10%, CCT 3000 K to

5700K, Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt. LED

driver efficiency > 85%. (fittings required LM-79 & LM-80 certificates)

(NOTE: Below description have shown ranges of Wattage capacity of LED

the ranges shown) (A) Street Light (IP-65), Surge protection -4KV integral

and ,Light must have 440VAC line supply with over-voltage protection. (ii)

above 48 to 60 Watts Cat-III (Contractor will have to bound for the

replacment warranty for 3 years incase of any deffect. There has been

also special condition provided in the tender form in this regard).

(B) Flood Light (IP-65), Surge protection -4KV integral and Light must 10.00 Nos. 9647.52

have 440VAC line supply with over-voltage protection.(vi) above 160 to

200 watts.Cat-III (Contractor will have to bound for the replacment

warranty for 3 years incase of any deffect There has been also special

condition provided in the tender form in this regard).

(C) Post Top Lantern LED fitting comprises of finish cast aluminum spigot 4.00 Nos. 4819.72

and spun aluminum canopy fixed with opal polycarbonate, pipe

arrangement for vertical mounting driver and accessories wired upto

terminal block. IP 65 (b) 40 W Cat-III (Contractor will have to bound for

the replacment warranty for 3 years incase of any deffect. There has been

also special condition provided in the tender form in this regard).

164 (c) LED Bollard fittings of minimum height 1000 mm & dia.100mm having 25.00 Nos. 4461.17

polycarbonate clear / milky diffuser mounted on 3mm thick aluminium

finished powder coated pipe with base plate 160 x 160mm with erection by

M8 x 75mm fastner with required RCC foundation. IP65 for 9 to 20 watt

and above, surge-4kv Cat-III (Contractor will have to bound for the

replacment warranty for 3 years incase of any deffect. There has been

also special condition provided in the tender form in this regard).

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

165 Providing and erecting Approved make Four pole moulded case circuit 3.00 Nos. 6790.43

breaker having breaking capacity ICU of 25 KA. at 415 V,having normal

current rating up to 25 A to 100A. with fixed thermal & magnetic release

suitable to work on A.C. supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in existing 16 G.M.S.

housing.ICS=100% of ICU only.Cat III with Enclosure.

166 Providing and erecting busbar chamber confirming to IS-375 fabricated 0.50 Rn.Mtr 4421.78

from 16 G.M.S. sheet, dust & vermin proof having hinged door with rubber

gasket and necessary busbar supports with COPPER busbar having

current density not more than 1.6 Amp. / sq.mm (Rated current / cross

section area) duly wrapped with colour insulation tape for phase

sequence, three phase & neutral each suitable for following current

capacity with necessary painting mounted on wall or pedestal frame of

required size with necessary connections. (A) Suitable for 63/100 Amp.

167 Supplying and erecting triple pole & neutral 440V / 500V panel mounting 0.70 Rn.Mtr 1961.42

Copper Busbars with four equal Nos. of electrolyte bus having current

density not more than 1.6 Amp. / sq.mm (Rated current / cross section

area) duly wrapped with colour insulating tape for phase sequence of

following current carrying capacity, erected with necessary bus bar

supports /insulators, main cable socket to each bar, erected in existing

cubical panel with necessary connections.(A) Suitable for 100 Amp.

168 Providing and erecting Miniature circuit breaker single pole 0.5A to 2A 54.00 Nos. 270.68

system and having breaking capacity 10 KA to be erected in existing box

confirming to IS 8828/1996 with ISI Mark.Cat-III

169 Providing and erecting Miniature circuit breaker single pole 6A to 25A 80.00 Nos. 112.11

suitable to operate on 240 V A.C. system and having breaking capacity

KA to be erected in existing box confirming to IS 8828/1996 with ISI Mark

170 Providing & erecting 240 V MCB double pole switch for lighting Load (B 4.00 Nos. 278.76

Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing

box having following capacity. (A) 6 to 32 Amp.Cat-III

(B) 40 Amp. Cat-III 3.00 Nos. 295.93

171 Providing & erecting 415V MCB Four Pole Switch for Lighting Load (B 7.00 Nos. 578.73

curve) having 10KA breaking capacity & confirms to IS :8828 in existing

box having following capacity. (a) 6 to 32 Amp. Cat-III

(b) 40 Amp. Cat-III 10.00 Nos. 638.32

172 Plastic enclosure fitted with DIN rail suitable for incorporating Three /Four 6.00 Nos. 108.07

173 Sheets steel powder coated enclosure suitable for incorporating One/Two 9.00 Nos. 176.75

174 Providing and erecting Sheet Steel powder coated MCB distribution board 1.00 Nos. 1492.78

- flush / surface mounted fitted with busbar, neutral link, earth bar and DIN

rail, Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same company of

MCB to be used) suitable for (A) single phase incoming and horizontal

single phase outgoing. (b) sheet steel double door (IP-43) (iv) 12 way

(B) three phase incoming and single phase horizontal type outgoing per 4.00 Nos. 2913.85

phase isolation type (PPI) (b) sheet steel double door (ii) 6 way

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

175 Providing and erecting Approved make RCCBs conforming to IS: 12640 6.00 Nos. 1969.50

and having sensitivity of 30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max. rating erected

as directed. (i) 25 Amps. DP.Cat-III

(ii) 40 Amps. DP Cat-III 12.00 Nos. 2235.13

176 Providing and erecting HOT deep Galvanised iron strip wire 8 to 16 SWG. 20.00 Kg 77.77

177 Pipe type earthing having 150 cms.long and 2.5 cms. dia. galvanised iron 40.00 Nos. 368.65

pipe with coupling and buch buried in specially prepared earth pit

complete with necessary 8 SWG earth wire.

178 For using salt and charcoal / coke as required for pipe type earthing. 40.00 Nos. 171.70

179 Supplying & erecting earth pit of minimum bore dia.150mm size approved 2.00 Nos. 4591.46

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS

3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe

dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm

having 200-250 Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive compound with

high charge dissipation suitable for following type of applications with

chamber and heavy duty cover.(approved make OEM has to submit test

certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2% (C)

Back fill Compound :- Earthing compound should be capable to retain

moisture for long time Necessary test report must be submitted. (a) For

Electrical Installation up to 440V in normal soil Length of pipe - 1 Mtr Back

filling compound - 1 Nos Bag of 15 Kg.

180 Providing & erecting weather proof, dust & vermin proof, floor mounted 1.00 Sq. 10468.65

front operated indoor type cubical panel board necessary IP-42 and above Mtr

protection as per approval from engineer incharge made from 14 SWG

thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC

M.S.sheet for internal partitions with necessary accesories , supporting

angles / flats channel including cutting, bending, drilling, welding, riveting

with internal partitions & cable alley as per requirements & instruction of

engineer-in-charge with erection of supplied switch gears, BUSBARS,

suitable size of inter connecting PVC copper wire / copper-aluminium

strips, rubber grommets, rib, bakelite control fuses / MCB for measuring

instruments, earth bus & earth bolts, foundation flange - bolts-base Plates,

sufficient nos. of hinged doors, handles with locking arrangement and

rubber gasket, heavy duty end terminal connection, danger notice board,

necessary ventilation, earthing strip complete.

The Panel shall be painted with epoxy powder coating. (The rates

excludes the cost of switchgears, bus bars, inter connecting mains &

Copper Aluminium strips, meters, fuses etc. The dimension shall be

measured excluding base beams) The panel shall be supplied with

following approved manufacturers with following size. (A) locally fabricated

panel board.(i) with 350 mm depth

181 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 375.00 Mtr. 92.92

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps

or in existing trench / pipe of following size of cables. (B) 2 core 6 Sq.mm

182 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable 100.00 Mtr. 220.18

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables.

(B) 3 1/2 core 35 Sq. mm (16 Sq.mm 1/2 core)

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

183 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable 1100.00 Mtr. 126.25

multistrand / Solid Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables (b)

4 core 6 Sq.mm

(C) 4 core 10 Sq.mm 300.00 Mtr. 140.39

184 Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable 50.00 Mtr. 153.52

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables.(A)

4 core 16 Sq.mm

185 Making trench in soft soil of suitable width of 90 cm deep for laying cable 1400.00 Mtr. 55.55

or locating the fault all over the run and back filling the same and making

the surface as normal ground.

186 Providing & laying approved make Double walled corrugated pipes (DWC) 1420.00 Mtr. 62.62

of polyethylene (conforming to IS 14930 II) with necessary connecting

accessories of same material at required depth in existing trench for

laying of cable below ground / road surface for enclosing cable (A) 50 mm

outer dia.

187 Providing and fixing heavy duty flange type brass cable gland with rubber 176.00 Nos. 38.38

ring for PVC insulated armoured cable complete with out going tails,

insulating tape etc. for following size of cables. (c) 2 to 4 core 6 Sq.mm

(C) 2 to 4 core 10 Sq. mm 20.00 Nos. 38.38

(D) 2 to 4 core 16 Sq. mm 6.00 Nos. 47.47

188 Providing and fixing heavy duty flange type brass double compression 2.00 Nos. 75.75

type cable gland with rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc. for following size of

cables. (B) 3 & 1/2 core 35/50 Sq. mm

189 Solder less crimping type Aluminium lugs conforming to IS suitable for 352.00 Nos. 6.06

cable of following size evenly crimped with high pressure tool & connected

to switchgear terminals with brass / cadmium plated nut bolts in an

approved manner. (A) 1.5/ 2.5/4/6 Sq.mm

(B) 10 Sq.mm 80.00 Nos. 13.13

(C) 16/25 Sq.mm. 26.00 Nos. 15.15

(D) 35/50 Sq.mm. 6.00 Nos. 20.20

190 Providing & erecting Approved make Power Saving 50 Watt Ceiling Fan 28.00 Nos. 1948.29

with double ball bearing ISI mark with Condenser 230 volt A.C. 50 Hz

1200 mm sweep complete having 3 blades with aluminium blades with,

canopy & 30 cm. down rod erected with earthing. (Make shall be approved

by Engineer in charge)

191 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. 28.00 Mtr. 108.07

Pipe down rod erected duly painted for fan complete with proper insulation

without leakage and earthing.

192 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to 28.00 Nos. 108.07

the RCC bars up to 50mm length each side and pierced through a

Gauge M.S. box / Heavy Duty PVC box complete erected concealed in

Ceiling with necessary finishing.

193 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or 28.00 Nos. 18.18

194 Supplying & erecting approved make low noise decorative exhaust fan 5.00 Nos. 1366.53

having square frame ABS body with inbuilt lowers & square frame.

250mm with 1350 RPM Cat.II

195 Providing recess in wall or window frame suitable for erection of Exhaust 5.00 Nos. 189.88

fan complete with plastering and colour washing to match the colour of the

wall or window complete with expanded metal in order to render the fitting

in accessible and the room water-proof.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

196 Supplying and erecting approved make Octagonal pole made from HR 29.00 Nos. 6874.06

sheet steel. The pole should be made as per IS and shall be coated with

hot dip galvanizing as per IS 2629/2633/4759, suitable suspend local wind

speed with integral Junction box consist of terminal plate of min 6mm

Hylam sheet, standard profile 35mm x 7.5mm Din-Rail for MCB Mounting,

stud type terminal and arrangement for cable termination to be erected

with suitable foundation (Included) as per details given by manufacturer

considering site requirement. (C) 5 Mtr. Long 70 mm top x 130 mm

bottom dia, 3 mm thickness with 200mm x 200mm x 12mm base plate, 4-

M16 bolts and 600mm long with necessary G.I. J bolts. Approx Pole

weight 46 kg

197 Supplying & erecting approved make SMC press moulded composite FRP 14.00 Nos. 476.72

loop-in, loop-out approx. 2mm thick box complete with Bakelite connector

strip 5way (3P+N+E), DIN rail for mounting mob & hinged doors as per

requirement having locking arrangements with mounting clamp with nuts,

bolts & washers suitable for erection on pole with cable clamps& earth bolt

of following size of box. (c) 150mm x 125mm x 100mm [deep]

198 Supplying and erecting Street light pole bracket comprising main B Class 18.00 Nos. 491.87

GI pipe of 4.2 cm/require outside dia. complete with suitable B Class G.I.

sleeve tubing of approx. 45cms. length and suitable for 76.5mm / 80mm /

require size of pole top having nuts and bolts for fixing the brackets and

having spread of 0.5 mtr. Length with 110 deg.with vertical plane and

suitable welded stiffener reducer and nipple with check nut complete

painted with one coat.of Red oxide / PU base primer and two coats of

Aluminium / PU paint. paint with following nos of arms. [A] Single Arm

bracket 0.5 Mtr

[B] Double Arm Bracket 0.5 Mtr 11.00 Nos. 622.16

199 Supplying & erecting approved make IP 55 grade Company fabricated 1.00 Nos. 12399.77

Timer Panel of following capacity for switch On-Off street lights on time

scheduling basis made from 16G CRCA sheet duly epoxy power painted

inside and outside with hinged doors and locking arrangement consisting

of suitable size of 4 Pole MCB and 4 pole contactor (Cat-III) with analog

time switch, auto manual switch of same make and suitable input and

output Bakelite terminals and with door earthing approved by Engineer in

charge. (A) 32 Amp

200 Supplying and erecting horizontal / vertical mounting type storage water 5.00 Nos. 8373.91

heater with copper container housed in M.S./S.S./ABS body insulated with

glass wool/puff complete with heating elements,adjustable thermostats

300C to 850C, indicating lamp, safety valve, fusible plug, etc. complete

erected with coach bolts, nuts. washers & cementation (A) 10 Ltr. with

KW. heating element Premium Category

201 Supplying and erecting approved make panel mounting type Digital 1.00 Nos. 1275.63

Voltmeter having 3 digits LED display, 0 to 750 AC Volts range erected

on existing panel board with all connection, wiring etc. with manufacturers

calibration certificate.

202 Supplying and erecting approved make panel mounting type Digital 1.00 Nos. 1558.43

Ammeter having 3 digits LED display, external CT operated, calibrated

for 0 to 1000 Amps suitable to operate on 500 Volt AC, erected on

existing panel board with all connection, wiring etc .with manufacturers

calibration certificate.

AC Supply 500 V on existing panel board with necessary connections.

204 Providing & erecting L.T. Current Transformer with bar primary 50/5 to 3.00 Nos. 274.72

1000/5 ratio 15 VA burden erected in existing CRCA box duly secured

with insulating materials connected to the meter.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

205 Supplying and erecting approved make suitable panel indicator LED type 3.00 Nos. 43.43

lamp, lens cover, complete erected with necessary connections.

206 Providing & erecting open well horizontal mono block pump set with cast 2.00 Nos. 18746.61

iron body, complete for three phase submersible motor having. [D] For

HP 3 phase open well horizontal mono block pump set suitable for

LPM to 310 LPM @ 10 to 42 Mtr head suitable for 50/65 mm dia. delivery

pipe. Cat.II

207 Supplying & erecting approved make motor control cubical panel [Star 2.00 Nos. 7250.79

delta] made from 16G CRCA sheet duly epoxy powder painted inside and

outside with hinged doors and locking with suitable size of ON - OFF

isolator (AC 3 / 23 duty) main fuses. Digital volt and current meter (in a

single unit) with micro controller based control unit and current sensing

single phasing preventer electronic overload protection, over voltage

(Programmable) protection and under voltage (Programmable) protection,

prod less dry run protection programming facility for setting of all

parameter like overload current, high voltage limit, low voltage limit, dry

run limit with digital indication on seven segment LED display for any fault

like over load, high voltage, low voltage, dry running single crimped,

electronic star delta timer, feather touch start / stop push buttons to be

erected on angle iron frame. Grouted on wall the contactors will be of L&

T, Siemens, BCH make only) (A) DOL up to 5.0 H.P.

208 Lowering of submersible motor pump set at the depth of following, 2.00 Nos. 856.48

complete with required. Nos. and size of casing pipes erected by means

of proper chain pulley block & pipe wrenches after checking of threads of

each pipe with coupling to take the load of the pump set and pipe

assembly filled up with water (D) For Open well horizontal submersible

pump set for sump well (i) 1 HP to 5 HP

209 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat 50.00 Mtr. 104.03

flexible Submersible copper cable approved make of following size. (B)

Core x 2.5 Sq.mm.

210 Supplying of following size of HEAVY UPVC column pipe with coupler and 30.00 RMT. 359.56

wire lock. [B] 50 mm dia.

Total Rs.

i.e. Rs. Two Crore Fourteen lacs Seventy thousand Eight hundred Fifty Four and Thirty Five paisa only.

I/We am/are willing to carry out the work @ ______________ % above/below percent (Should be written

in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

Net Rs. ___________________________ Total Rs. ________________________

In words ____________________ In words ____________________

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-In-

Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where there

is a change as per actual mix design the cost of difference of cement consumption have been deducted from the

rate of original item at the rate of input rate mentioned in all the tender.

It. Rates in Total

Description of Item Qty. Unit

No. Figure Amount

5. The Contractor will have to submit the all required mix design at his own cost before execution as

directed and to be approved from the Engineer in charge.

6. Credit for dismantalled materials of amount of Rs. 7,60,422.00 must be recovered from 1st R.A. bill of

Contractor's.

Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me and

Executive Engineer

R & B Division,