PROVN OF INTERLOCKING TILES RAILLINGS AND KERB STONES NEAR DRILL SQUARE FALSE CEILING AND WALL PANELING IN COMDT FOYER AT FF OF TAB CONCRETE PAVEMENT FROM SALARIA SWIMMING POOL TO DRIL SQUARE NEAR SOMNATH STADIUM AND FLYPROOFING SWIMMING POOL AT

Amount

Surface excavation not exc 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

Excavating in trenches, not exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits manholes, pier holes, etc not exc 10sqm on plan and not exc 1.5m in depth and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level not exc1.5m above the starting point complete all as specified and directed.

PCC 1:4:8 type D-2, using 40 mm graded stone agg as in foundation, filling, mass concrete and sub base of floor complete all as specified and directed.

Brick work with sub class 'B' bricks (old size) straight or curved on plan exc 6.00m mean radius built in CM (1:6) complete all as specified and directed.

80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand complete, all as specified and directed.

Factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, coping, benching, kneelers, apex stone, bed plates, kerbs, etc. including weathering, slightly rounded or chamfered angles and throating, including necessary from work etc complete all as specifed and directed.

Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Mild steel TMT bars 8 mm dia cut to length, bent to shape required, including cranking , bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

Factory made decorative precast RCC M-20 balustered/ vertical post of 60cm height, sectional area not less than 225sqcm of required shape and size, medium duty of suitable thickness , ISI marked, set in cm 1:4 complete all as specified and directed.

Preparation of wall surfaces and finishing with Acrylic Smooth exterior paint of required shade with (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

Tongue & groove pine wood false ceiling using top quality pine planks with profile section 12x102mm fixed on pine wood grid of size 600mmx 600mm using section 40mmx65mm hanged with suspender from MS truss/RCC roof fixed in repair including finishing the ceiling with high gloss PU polish (Asian/berger/ICI) with gun spray after preparation of surface as per manufacturer’s specification and to the satisfaction of Engineer-in- charge. Note :- 1. MS truss & suspender shall be measured & paid in relevant item. 2. The work shall be carried out above 7.5m height. 3. Arrangements are to be made to accommodate light fixtures by forming recessed channel etc wherever directed.

Providing & fixing non anodised aluminium rectangular hollow sections size 50.8x 25.4mm x 1.16mm wall thickness for panelling, to be placed at 600mm apart in both vertical and horizontal directions. Extra members at corners/junctions are also to be provided. The frame shall be fabricated & installed in position firmly with the help of suitable aluminium cleats, screws, clamps, rawl plugs complete all as specified and directed.

12mm thick plywood grade BWR, type BB, fixed with screws to aluminium frame work as in wall panelling complete all as specified and directed.

4mm thick Veneered decorative plywood grade 1 (with BWR resin) with decorative face veneers on one face, fixed with nails to timber frame work complete all as specified and directed

1st class hard wood fillets bull Nosed, splayed, chamfered or rounded on one edge or face, sectional area exc 6sqcm and not exc 13 Sqcm fixed with nails complete all as specified & directed.

Preparation of new or previously untreated wooden surfaces of any description, over 10cm width or girth and apply two coats of synthetic varnishing over a coat of wood filler liquid transparent complete all as specifed and directed

Rolled structural mild steel work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates complete all as specified and directed.

Preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as directed.

Broken stone hard core of gauge n. exc. 63mm, deposited, spread and levelled in layer n. Exc 15 Cm thick watered & rammed to a true surface complete all as specified and directed.

100 mm thick PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in hard standing / path including spike rolling or making impression of expended metals while the concreate is green complete all as specified and directed.

Forming construction joint 30 mm deep x 10 mm wide and filled with sealing compound grade A complete all as specified and directed.

Use & waste for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter including fair finished surfaces complete all as specified and directed.

Use and waste of formwork to sides and soffits of arches including supports etc. and similar work of rough finished curved surface of concrete complete all as specified and directed.

Use and waste of formwork to sides and soffits of floors or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports etc. and similar work of fair finished flat surface of concrete complete all as specified and directed.

Use and waste of formwork to sides of concrete pillar, columns, posts strutts complete all as specified and directed.

RCC M -25 (Design Mix) using 20mm graded crushed stone aggregate as in foundations, including rafts, footing, foundation beams, plinth beams, bases for columns etc, basement slab, under-reamed piles and mass concrete etc complete all as specified and directed.

RCC M -25 (Design Mix) , type B-1using 20mm graded crushed stone aggregate as in beams, cantilever bressummers lintel over 1.5 m span etc complete all as specified and directed.

RCC M -25 (Design Mix) using using 20mm graded crushed stone aggregate as in arches supported on walls beams and columns in floor, roof, landing and in shelves and the like complete all as specified and directed.

RCC M -25 (Design Mix) using using 20mm graded crushed stone aggregate as in column ,pillars, piers,posts and struts complete all as specified and directed.

Rendering 10mm thick plaster on fair faces of brick work or concrete surface in CM 1:3 finished even and smooth without using extra cement, complete all as specified and directed

Extra over rendering or plastering for work in isolated widths or in widths and forming part of general plastering such as in bands,sunk panels, cornices, skirtings, drip moulds and similar work exc 15cm but n.exc 30cm in width including cutting to edges, all mitre and stopped ends etc complete all as specified & directed.

3mm thick wall care putty on wall, columns, arches including architrave complete all as specified and directed.

Mild steel framed work such as grills, grating etc with end of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing framed work of water tanks and similar work including pintal hinges, stops hand made sliding bolts etc complete all as specified and directed Note:- The work shall be carried out above 7.5m between roof and wall of swimming pool, scaffolding and other arrangement required to complete the work deemed to be included in the quoted rate.

Wire netting of galvanised steel wire cloth,1.4mm dia and mesh size 12mm fixed with tinned tacks, galvanized wire of staples complete all as specified & directed Note:- The work shall be carried out above 7.5m between roof and wall of swimming pool, scaffolding and other arrangement required to complete the work deemed to be included in the quoted rate.

M/s RK ENTERPRISES

M/s Varun Kumar Contractor