Loading…
Loading…
Tender Value
₹2.2 Cr
EMD Value
₹2.2 L
Closing Date
1 Jul 2026, 6:00 pm2d left
Similar tender results from the same govt authority in the past 3 years.
Chief Engineer (Operation)
Extension of Third floor of New R & C office for Conference Room, Record Room and Other Misc. Works at UGVCL, Mehsana campus
312808
UGVCL/Civil/328/2026-27
Open
Civil Works - Buildings
Mehsana
18 documents required · 18 mandatory
₹8,850
Uttar Gujarat Vij Company Limited
₹2.2 L
11 Jun 2026
11 Jun 2026
11 Jun 2026
1 Jul 2026
11 Jun 2026
Name of work: Extension of Third floor of New R & C office for Conference Room, Record Room and Other Misc. Works at UGVCL, Mehsana campus.
Sr. No. Description Qty. Unit Rate Amount
1 Dismentalling tiled of stone floors laid in moter including stacking of serviceable 905.00 SMT 48.69 ₹
materials & dispossal of unserviceable materials with all lead & lift
2 Demolition of brick work & stone masonary including stacking of serviceable 55.00 CMT. 557.27 ₹
materials & disposal of unserviceable materials with all lead & lift. (ii) In cement
3 Demolition including stacking of serviceable materilas and disposal of unserviceable 18.00 CMT. 1071.12 ₹
materials with all lead and lift. (i) R.C.C. work
4 Removing and scraping of old deteriorated plaster of any thickness fromm wall / 90.00 SMT 19.72 ₹
R.C.C member including stacking of serviceable material and disposal of
unserviceable from site of work with all lead and lift
5 Dismentalling doors, windows, ventilators, etc. (Wood or steel shutters including 18.00 Each 189.95 ₹
chowkhars, Architraves, Holdfasts and other attachment etc. complete and stacking
them within all lead and lift. i) Not exceeding 3 Sq.M. in area
6 Dismentling C.I. pipes G.S.W.pipes abd A.C. rain water pipes with fittings and 190.00 RMT 75.97 ₹
clamps including stacking the materials with all lead and lift ( for any dia, of pipe)
7 Excavation for foundation upto 1.5 m depth including sorting out and stacking of 12.00 CMT. 269.87 ₹
useful materials and disposing off the excavated stuff upto 50 Meter lead.(B) Dense
or Hard soil, Manual Labour
8 Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and 8.00 CMT. 292.18 ₹
stacking of useful materials and disposing off the excavated stuff upto 50 Meter
lead.(B) Dense or Hard soil, Manual Labour
9 Providing and laying cement concrete 1:4:8 (1-Cement:4-coarse sand:8-machine 2.00 CMT. 2733.19 ₹
crushed stone aggregates 40 mm nominal size) and curing complete excluding cost
of formwork in (A) Foundation and Plinth
10 Filling available excavated earth (excluding rock) in trenches, plinth, sides of 20.00 CMT. 135.56 ₹
foundations etc. in layers not exceeding 20 cm. In depth consolidating each
deposited layer by ramming and watering.
11 Providing and laying Controlled cement concrete work M250 (1- Cement : 1- 4.00 cu.m 4141.73 ₹
Coarse sand : 2- graded stone aggregates 20 mm nominal size) and curing complete
excluding cost of formwork and reinforcement for reinforced concrete work in (A)
Foundations, footings, Base or columns and Mass concrete
12 Providing and laying controlled cement concrete M.250 and curing complete 10.50 cu.m 4448.86 ₹
excluding the cost of formwork and reinforcement for reinforced concrete work in
(B) Walls, from top of foundation level upto floor two level
13 Providing and laying controlled cement concrete M.250 and curing complete 5.80 cu.m 4487.88 ₹
excluding the cost of formwork and reinforcement for reinforced concrete work in
(B) Walls, from top of foundation level Upto floor two to three level
14 Providing and laying controlled cement concrete M.250and curing complete 6.00 cu.m 4526.90 ₹
excluding the cost of formwork andreinforcement for reinforced concrete work in
(B) Walls, Upto floor three to four level
15 Providing and laying controlled cement concrete M.250 and curing complete 9.00 cu.m 4565.92 ₹
excluding the cost of formwork and reinforcement for reinforced concrete work in
(B) Walls Upto floor four to five level
16 Providing and laying controlled cement concrete M.250 and curing complete 84.00 CMT. 6292.70 ₹
including the cost of formwork and excluding the cost of reinforcement for
reinforced concrete work in (C) , Slab upto floor four to five level.
17 Providing and laying controlled cement concrete M.250 exposed work with curing 38.00 CMT. 8089.04 ₹
etc. complete including the cost of formwork but excluding the cost of
reinforcement for R.C.C. work in Beams
(A) Having cross sectional area more than 0.12 Sq. M. and up to 0.18 Sq.M.
(Above floor four to five level)
18 Providing and laying controlled cement concrete M.250 exposed work with curing 3.10 CMT. 9570.09 ₹
etc. complete including the cost of formwork but excluding the cost of
reinforcement for R.C.C. work inBeams Having cross sectional area 0.08 Sq. M.
to 0.12 Sq.M. (Above floor four to five level)
19 Providing and laying controlled cement concrete M.250 exposed work with curing 33.00 CMT. 10280.73 ₹
etc. complete including the cost of formwork but excluding the cost of
reinforcement for R.C.C. work in(B) COLUMNS: (iii) Having cross-sectional area more
than 0.12Sq.M and upto 0.18 Sq.M (above four to mumty level )
20 Providing and laying controlled cement concrete M.250 and curing complete 11.00 CMT. 6315.79 ₹
including the cost of formwork and excluding the cost of reinforcement for
reinforced concrete work in (C) , Lintels up to floor four to five level.
21 Providing and laying controlled cement concrete M.250 and curing complete 13.00 CMT. 6165.26 ₹
including the cost of formwork and excluding the cost of reinforcement for
reinforced concrete work in (C) Chajja up to floor four to five level.
22 Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding 2200.00 KG 76.52 ₹
and placing in position complete upto floor two level
23 Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding 800.00 KG 77.56 ₹
and placing in position complete upto floor two to three level
24 Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding 850.00 KG 78.60 ₹
and placing in position complete upto floor three to four level
Sr. No. Description Qty. Unit Rate Amount
25 Providing TMT Bar FE 500D reinforcement for R.C.C. work including bending, binding 26750.00 KG 79.64 ₹
and placing in position complete upto floor four to Five level
26 Providing formwork of ordinary timber planking so as to give a rough finish including 5.00 SMT 180.05 ₹
centering shuttering strutting and propping etc. Height of propping and centering
below supporting floor to ceiling not exceeding 4 M. and removal of the same for in
situ reinforced concrete and plain concrete work in. (A) Foundations Footings Bases
of Columns etc. and Mass concrete.
27 Providing formwork of ordinary timber planking so as to give a rough finish including 360.00 SMT 255.72 ₹
centering shuttering strutting and propping etc. height of propping and centering
below supporting floor to ceiling not exceeding 4 M. and removal of the same for in
situ reinforced concrete and plain concrete work in. (C) Vertical surface such as
walls (any thickness) partitions and the like including attached buttresses & string
course & the like
28 Brick work using common burnt clay building bricks having crushing strength not less 240.00 CMT. 3772.05 ₹
than 35 Kg./ sq.cm. in Super structure (Above floor Four to five level) in cement
mortar 1:6 ( 1 cement : 6 Fine sand ) (B) Conventional
29 Half brick masonary in common burnt clay building bricks having crushing strength 60.00 SMT 600.30 ₹
not less than 35 Kg./Sq.cm. in cement mortar 1:4 (1cement :4 coarse sand) in super
structure (above floor Three to four level). With CONVENTIONAL BRICKS
30 Providing fitting & fixing fully glazed/ partly glazed double leaf anodised 5.00 SMT 11150.00 ₹
aluminium entrance door using extruded section fabricated by standard
manufactures with framing 10.15cm x4.45cm rectangular section & door shutter
made from 10.15 cm x 4.45cm aluminium bottom section top & vertical section
6.35x3.80cm size using 5.5mm thick "Triveni"or HB4 smoke glass with glazing deep
rubber gasket with locking arrangement(Godrej type) with all fixtures & fastenings
of anodised section with aluminium bedding floor spring mounted double door
closer with all labours & materials etc. Complete as per drawing and as directed by
E.I.C..Item also includes powder coating to alluminium sections of approved colour /
shade incl. all materials,labour,tools & tackles etc. complete.
31 Providing and fixing FRP frame size 100x50 mm and 28mm thick FRP depress panel 20.00 SMT 2354.22 ₹
shutter having extra reinforcement on sides & edges in Gel coat finish. The core of
the shutter & frame is to be filed up with injected fire retardant grade polyurethene
foam done in situ alongwith embedded wooden pieces for stiffening & also taking
hinges & fintures. The whole FRP frame & shutter is to be water proof weather
proof, termite proof & resistance to mild acid/alkali. Rates are to be inclusive of S.S
hinges with necessary screws & alluminium fixtures & fastenings & fastener sleeve.
32 Providing and fixing 35 mm thick shutters for Doors, windows and clerestory 2.50 SMT 5285.45 ₹
windows including Indian teak wood frames 10 cm x 7 cm. size including black
enamelled iron oxidixed fixtures and fastenings including primer coat of approved
quality and two coats of oil painting etc, complete. (ii) Fully Panelled.
33 Providing and fixing window having extruded alluminum colour anodized section 75.00 SMT 1696.73 ₹
frame main outer size 63.5 x 38.10 x 1.95mm (of Jindal Section no4605,@ wt
Kg/Rmt), horizantal two track member size 61.85mm x 31.75 mm x 1.20mm (of
Jindal section no 8687 @ wt of 0.695kg/Rmt), vertical memberof size 61.85mm x
31.75mm x 1.30mm (of jindal section no 8758 @ wt of 0.659kg/mt) with sliding
shutter of horizantal member size 40mm x 18mm x 1.29mm (of jindal section no
8949 @ wt of 0.456kg/Rmt), vertical member of size 40mm x 18mm x 1.29mm (of
jindal section of 8947 @ wt of 0.456kg/mt, section 8948 @ wt of 0.457kg/mt) with
5mm thick transparent bronze colour tinted float glass with powder coated
alluminum fittings and fixtures and transparent silicon sealant glass fixing to frame
as per details etc complete (For two track window).
34 Providing and fixing standared extruded of alluminium section of size 63mm x 2.60 SMT 1163.92 ₹
38.10mm x 1.2mm (Jindal Section :2434, @ Wt. 0.643 Kg/mt) with colour anodized
alluminium frame for ventilation with 5 mm thick frosted glass as details etc
complete for Ventilation
35 Providing 20mm. Thick double coat mala cement plaster on interior brick / concrate 1750.00 SMT 362.51 ₹
work for plastering comprising of base coat of 12mm thick cement plaster in (i)
Cement mortar 1:4 ( 1 cement :4 coarse sand)in rough finishing and 8mm thick top
coat of cement mortar 1:2 (1 cement :2 coarse sand) finished with trovel incl.
scafolding, curing etc complete.up to floor four to five level.
36 20mm. Thick sand faced cement plaster (Tipani with Gutka) on walls up to height 10 690.00 SMT 317.92 ₹
meters above ground level consisting of 12mm. Thick backing coat of C.M. 1:3 (
cement : 3 sand ) and 8 mm. thick finishing coat of C.M. 1:1 ( 1 Cement :1 sand)
etc.. Complete.
37 Providing and laying polished Kota stone slab flooring over 20mm (Average) thick 180.00 sqm 1008.91 ₹
base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 laid over and
jointed with grey cement slurry including rubbing and polishing etc. complete. (B)
25mm. Thick ( 600 X 450mm. Size )
38 Providing & laying POLISHED KOTAH STONE slab 25mm. Thick in risers of steps dado 20.00 sqm 1155.38 ₹
and pillars laid on 10mm. thick cement mortar 1:3 ( 1 cement : 3 coarse sand) and
jointed with grey cement slurry including rubbing & polishing etc.. Complete.
39 Providing and laying Vitrified tiles 8 to 10 mm thick , 36'' x 36'' in flooring treads of 435.00 SMT 1516.65 ₹
steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-
coarse sand) finishing with flush pointing in white cement.
40 Providing & laying 20 to 25mm thick, both faces polished kotah stone with all edges 0.00 sqm 1008.91 ₹
machine cut up to 450mm width and of required length (only one piece to be used
) of approved quality for cupboard shelves including fixing the same in masonry
wall/ RCC work.
41 Providing and laying granite for entrance steps,water counter etc. flooring over 20 130.00 Sqm 4454.67 ₹
mm. (average) base of cement mortar 1:6 (1 cement : 6 coarse sand) or L.M. 1:1.5
and jointed with grey cement slurry including rubbing and polishing complete.
Sr. No. Description Qty. Unit Rate Amount
42 Labour charges for making moulding edge to granite incl. all tools,tackles etc. 785.00 RMT. 85.00 ₹
complete as directed.
43 Labour charges for making moulding edge to Kota incl. all tools,tackles etc. 60.00 RMT. 51.00 ₹
complete as directed.
44 Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in skrting risers of 120.00 SMT 1130.15 ₹
steps and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and
jointed with white cement slurry
45 P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of 420.00 SMT 1383.99 ₹
cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on existing
flooring by adhesive material including dismentaling of existing flooring and jointed
with color cement slurry including finised with flush pointing & cleaning the surface
etc. complete for antiskit
46 Providing & fixing of first quality white/coloured vitereous china table top type 12.00 Nos 6039.00 ₹
wash basin as per product detail, including 300 mm Bottale Trap, 32mm CP brass
full thred waste coupling as per product detail, PVC pipe for waste connection,
12mm dia & 450 mm length nominal bore heavy rating CP brass inlet connection
with unions at end for connection of angular valve to basin as per product
detail complete including fixing wash basin with counter top by approved type poly
sulphide sealent, and making good the walls where required. The scope includes the
items as per specifications and product details as per under. Table top wash basin.
CERA CAT NO: Cat. No. S2020137 (CALBURT-Snow White) , Bottle Trap Cera Cat No.
F8060401, Connection Pipe Cera Cat No: F8070403, WASTE COUPLING 32mm with
125 mm length : CERA ALD-F8050301 OR EQU.
47 Providing & fixing C.P. brass pillar tap with all nuts, washer and brass flange etc 12.00 Nos. 2035.00 ₹
complete as per specifications and product detail as under: Cera Cat No : F1005101
48 Providing & fixing brass screw down stop tap (A) 15mm. Dia. 20.00 Each 203.79 ₹
49 Providing and fixing valve.(A) 25mm dia. Controll Valve 20.00 No 1710.00 ₹
50 Providing & fixing of box rim pattern wall mounted cantilever type white/coloured 12.00 Nos 19043.00 ₹
vitreous china Wall Mounted water closet including flushing cistern with C.P bolts,
nuts, CI chair (painted with two coats of enamel paint over a coat of primer) or
other hanging arrangements, bakelite / poly propylene soft closing seat cover with
C.P. hinges & rubber buffers, connector pipe from P/S trap to drainage pipe, brided
hose pipe complete with all accessories. Including cutting & making good the walls
& floors wherever required. The scope include the items as per specifications and
product details as under: EWC-P:- WALL MOUNTED CERA CAT NO: S1044147
(CARLTON with Duroplast slim soft close seat cover)+ Rug Bolts B2040101 + Cistern
Half Frame Cat No. B1110112 (CHEVRON) + Knob Cat No B1120105 OR EQ
51 Providing & fixing Health faucet with 1.0mtr flexible Health faucet brass body with 12.00 Nos 1973.00 ₹
wall hook and 1 metre SS braided rubber hose pipe Tube, wall hook, CP wall bracket
for hanging the hand faucet, connecting CP angular stop cock with wall flange etc.
complete as per specification and product detail as under: Cera Cat No : F8030301
52 Providing & fixing 6mm thick, copper back finish, looking mirror of required size, 1.00 Nos. 2718.25 ₹
made of float sheet glass of best quality & approved make, over 12 mm thick marine
board fixed to rawl plug with round head screws and washers including teak wood
beading with melamine polish all around, complete in all respects inclusive of cost
of all materials, labour, tools, tackles etc. as per specifications and direction of EIC.
53 Providing and fixing 600mm x 450mm bevelled edge 11.00 NO. 850.90 ₹
mirrror of superior glass mounted on 6mm thick A.C.
sheet or plywood sheet and fixing to wooden pluge with
C.P. brass screws and washers.
54 Providing & Fixing C.P. Brass towel rail complete with C.P. brass brackets fixed to 12.00 NO. 610.32 ₹
wooden plugs with C.P. brass screws. (B) 600mm x 20mm Size
55 Providing & Fixing white / coloured porcelain flat back wall type URINAL PAN of 8.00 Nos. 3913.91 ₹
CERA make with integrated EFS having size 320 * 300 *525 mm of approved quality
& make including waste coupling (Full Threded) bends & necessary outlet of
25mm.dia. G.I. Pipe connections including providing Bottle Tarp,PVC
connection,spreader & spreader pipes,brackets etc., completed as directed by
E.I.C.As per RA attached.
Cera Cat No : Cat. No. S4020104, P.86 (CARYS Urinal) + Connection Pipe Cera
Cat No: F8070403, P.170 + F8070201 Urinal spreader + WASTE COUPLING: CERA
ALD-F8050101 Page no. 170 or EQ
56 Providing & fixing PVC SWR Nahani trap IS 14735 for drain - 100 mm diameter with 20.00 Each 580.79 ₹
jali of the following nominal diameter of self cleansing design with C.I. screw down
or hinged grating including cost of cutting & making good the walls and floor (
100mm. Inlet and 50mm. Outlet)
57 Providing & Fixing PVC Gully trap with C.I. grating brick masonary chamber & water 16.00 Each 1466.77 ₹
tight C.I. cover with frame of 300mm X 300mm.size inside with standard weight.
(i) Square mouth trap (B) 160mm. X 110mm. size P or
58 Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure 40.00 RMT. 172.26 ₹
poluthene pipes of the following outside Dia. Low densidy, complete with special
falnge compression type fittings, wall clipsetc. including making good the wall
ceiling and floor.(E) 50mm
59 Providing and fixing to wall ceiling and floor 10.0 kg. F/cm2 working pressure 25.00 RMT. 277.46 ₹
polythylene pipes of the following outside dia. special density, complete with
special flange compression type fittings, wall clips etc. including making good the
wall ceiling and floor. (a) 75mm. dia.pipe.
Sr. No. Description Qty. Unit Rate Amount
60 b) 110mm.dia.pipe. (Rain water Pipe) 210.00 RMT. 335.69 ₹
61 Providing Laying and jointing in true line & level 15 mm dia. U.P.V.C. pipe (Sch 20.00 RMT 71.93 ₹
40) for cold water including fittings of make PRINCE/SUPREME/ASTRAL/FINOLEX or
equivalent as approved by EIC. pipe shall be fixed on the wall with the help of clamp
at every two meter C/C or shall be concelled as directed including necessary fittings
etc and fixing the same with adhesive solvent including cost of all materials etc
62 Providing Laying and jointing in true line & level 25 mm dia. U.P.V.C. pipe (Sch 130.00 RMT 90.93 ₹
40) for cold water including fittings of make PRINCE/SUPREME/ASTRAL/FINOLEX or
equivalent as approved by EIC. pipe shall be fixed on the wall with the help of clamp
at every two meter C/C or shall be concelled as directed including necessary fittings
etc and fixing the same with adhesive solvent including cost of all materials etc
63 Providing, Laying and jointing in true line & level 50mm dia. U-PVC pipe ( SCH-40) 100.00 RMT. 193.73 ₹
line including fittings of make as approved by EIC. Pipe shall be fixed on the wall
with the help of clamp at every two meter C/C OR shall be concealed as directed
including necessary fittings etc including testing of pipe and joints and fixing the
same with adhesive solvent including cost of all materials and labour etc complete.
64 Providing and fixing Gun metal check or non-return fullway wheel valve.(A) 15mm 10.00 Nos. 184.98 ₹
65 Providing & Fixing & functioning of PVC ball Valve as approved make as directed by 5.00 No 349 ₹
EIC, b) 25mm.dia. valve.
66 Providing & Fixing 50 mm.dia. UPVC valve. 10.00 NO. 779.00 ₹
67 Providing & fixing approved and tested quality bib cock with all fittings complete as 5.00 Nos 1645.00 ₹
per specifications and product detail as under: Cera Cat No : F1005151 or EQ
68 Providing, Erecting & Fixing ready made double coated sintex P.V.C. (ISI) or 10000.00 litre 3.91 ₹
equivalent ISI water storage tank of required capacity each with cover including
providing & fixing one 20mm.dia. float valve ball‑cock , one 20mm dia. G.I. Waste
pipe with plug, one 25mm dia. G.I. over flow pipe of length up to 0.30mt. including
making all connection for inlet/outlet supply with necessary fittings etc. complete
on terrace. (A) 1000 Liter capacity
69 Providing cement vata (10cm X 10cm. Size) quarter round in cement mortar 1:1 60.00 RMT. 24.04 ₹
including neat cement finishing, watering etc.. Complete.
70 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC 30 Ea. 125.00 ₹
bars up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy
Duty PVC box complete erected concealed in Ceiling with necessary finishing.
71 Providing & fixing china mosaic tiles flooring as water proofing treatment including 580.00 Sqm 771.98 ₹
(a ) Applying cement slurry of cement admixed with water proofing compound after
cleaning the surface properly. (b) Cracks in slab shall be open in ' V ' groove & all
loose materials shall be removed & crack filling shall be done with special &
approved type of expanding crack fillet material . ( c ) Depressions in slab if any be
filled up with C.C.(1:2:4 ) I.P.S.flooring. ( d ) P / L 20 mm thick plaster layer in C.M.
( 1:4 ) with cement admixed with water proofing compound including rounding of
junction of walls and slab by making cement vata. ( e ) Finishing the surface with
china mosaic tiles (pieces ) flooring incl.fixing the same in cement mortar (1:2)
setting with ready made tile adhesive as recommended by manufacturer’s including
fillings of joints mixed with pigmented white cement slurry of matching shade &
finally finishing the surface with trowel with white cement slurry etc., complete ( f
) After finishing, the whole terrace shall be flooded with water to check the
performence of work.
72 Providing and fixing single layer waterproof gypusm board 12.5 mm thick sections 165.00 Sqm 600.94 ₹
using waterproof board of size 1220 mm x 1830 mm x 8.0 mm suspended by G.I
suapender of size 25 mm x 3 mm with intermediate channel of size 18 mm x 40 mm
x 0.80 mm at 1220 mm center to center ceiling section of size 40 mm x 35 mm x
0.55 mm at 457 mm center to center and perimetre chanel A of size 20 mm x
mm x 30 mm x 0.50 mm at edges & drops including paper tap sand sofit cleat,
anchor fastener, scoch bolt connecting cleat joining compound top coat on ceiling
including making necessary opening for light fitting, diffuser etc. complete as per
detail drawing as directed.
73 Providing & fixing stainless steel sink with drain board of approved make & size of 4.00 No 1732.50 ₹
1'-6" *1'-5" * 0'-7" incl. Waste couplin & waste pipe for water stand as directed.
74 Removing dry or oil bound distemper by a washing and scraping and sand papering 5200.00 SMT 11.39 ₹
the wall surface smooth including necessary repairs to scratches complete.
75 Wall painting (two coats) with plastic emulsion paint of approved brand and 7200.00 SMT. 82.15 ₹
manufacture on undecorated wall surface to give an even shade including throughly
brushing the surface free from mortar droppings and
other foreign matter and sand papered smooth.
76 Applying one coats of Birla Or Asian acrylic lapi (putty) & two coats of primer 3500.00 SMT 40.19 ₹
approved brand and manufacture on new wall surface to give an even shade
including throughly brushing the surface free from mortar dropping and other
foreign matter and sand papered smooth
77 Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) 2200 SMT 73.02 ₹
to give an required shape even shade after thoroughly brushing the surface to
remove all dirt, and remains of loose powdered materials.etc complete
Sr. No. Description Qty. Unit Rate Amount
78 Providing & fixing steel cupboard shutter of 18 gauge with steel frame and fixing the 15.00 SMT. 2854.50 ₹
frame with brick masonry including locking arrangement with 3 coats of approved oil
paint etc., complete.
79 Providing & Fixing curtains for window with S.S. curtain rod and bracket/clamp 70.00 SMT 1996.00 ₹
/ring with complete accessories incl powder coating of approved shade & make. for
fixing the same in line & level with premium quality and elegant style Main Cloth +
blackout curtain fabric incl.stiching charges for curtain and labour charges for fixing
brackets/clamps & Power track channel/curtain rod etc.complete as directed by
E.I.C. NOTES : Measurements will be paid in sq. mt.for the area of
window opening.
80 Providing and fixing in position S.S. hand rail in main stair case, landing ,balconies 15.00 RMT 2625.00 ₹
etc. inHorizontal 2"(50mm) dia S.S. pipe & Four horizontal 3/4"( 20 mm) S.S.
pipesize S.S.Resting by Round bars 1.5" dia of clear height 90cms placed at 3feet
c/c including making necessary hold fast fixture taircase concrete for resting the S.S
304 grade . vertical posts with holding etc. as per approved design and as required
for the work including bending hand rail pipe to proper shape in curves with
specials etc. complete . Railing height is 0.9M.
81 Providing & Laying Water Proofing Treatment in Sunken Portion of W.C., Bathroom, 115.00 Smt 395.00 ₹
Terrace etc. by applying Cement Slurry mixed with water proofing chemical ,as per
manufacturer's specifications of approved make as under.
82 Providing & applying Dr.fixit( pidilite)LW+ OR equivalent, In RCC Work using 200ml 205.00 Ltr 78.00 ₹
per bag as directed & instructed by E.I.C
83 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) 100 Pt. 495.00 ₹
both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up
to 5 mtr length , in below type of pipe erected with 6A Modular type switch / bell
push & accessories and earth continuity of following type, erected on PVC /
Metallic/Wooden box, single mounting base frame covered with
textured/metallic/white front plate modules erected on / in wall / ceiling as per
pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as
directed.(f) with medium class Rigid PVC pipe and accessories erected concealed in
wall/ceiling completeCat. III
84 Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) 60 Pt. 695.00 ₹
both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up
to 10 mtr length , in below type of pipe erected with 6A Modular type switch / bell
push & accessories and earth continuity of following type, erected on PVC /
Metallic/Wooden box, single mounting base frame covered with
textured/metallic/white front plate modules erected on / in wall / ceiling as per
pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as
directed.(f) with medium class Rigid PVC pipe and accessories erected concealed in
wall/ceiling completeCat. III
85 Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of 15 Pt. 523.00 ₹
ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 20 mtr
length, in below type of pipe erected complete with Modular type switch & 5 pin
Plug erected on PVC / Metallic/Wooden box covered with appropriate front plate
modules erected on / in wall / ceiling as per pipe erected with following type of
accessories.[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby
switchboard/mcb db board(f) with medium class Rigid PVC pipe and accessories
erected concealed in wall/ceiling completeCat. III
86 Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket 60 Pt. 266.00 ₹
erected on PVC / Metallic/Wooden box, single mounting base frame covered with
textured / metallic/white front plate modules erected on / in wall / ceiling with
following type accessoriesCat. III
87 [III] For 16A Plug and 16 amp switch with 2-4 sq.mm Cu. Wire with 2.5 sq.mm ( 25 Pt. 906.00 ₹
green) earthing wire from mcb d b board.(f) with medium class Rigid PVC pipe and
accessories erected concealed in wall/ceiling completeCat. III
88 Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size 400 Mtr. 36.00 ₹
complete to be erected on/in wall or ceiling erected with necessary PVC fittings &
Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, in
approved manner as directed (b) 25 mm
89 Providing & erecting PVC Corrugated Flexible Conduit with required nos. of coupling, 60 Mtr. 23.00 ₹
PVC bushes, Check-nuts etc. complete of following (2) 25 mmsizes.
90 Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked 400 Mtr. 68.00 ₹
stranded Copper conductor wire in following type of pipe to be erected concealed
in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC insulated
stranded wire of green colour for earth continuity of following size (A) With medium
class Rigid PVC pipe and accessories(a) 2 wire 1.5 sq. mm Cat.III
92 providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked 500 Mtr. 123.00 ₹
stranded Copper conductor wire in following type of pipe to be erected in / on wall
/ ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire of
green colour for earth continuity of following size(A) with medium class Rigid PVC
pipe and accessories(a) 2 wire 4 sq. mm
93 (b) 2 wire 6 sq. mm 30 Mtr. 162.00 ₹
94 (h) 4 wire 6 sq. mm 50 Mtr. 289.00 ₹
95 (i) 4 wire 10 sq. mm 50 Mtr. 472.00 ₹
(use earth wire of 4 sq.mm )
Sr. No. Description Qty. Unit Rate Amount
96 providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi 30 Mtr. 29.00 ₹
stranded, annealed copper conductor with heat resistant PVC insulated conforms to
IS 694, IEC - 227 erected in existing pipe of following size (Specifically for control
panel, relays, power switchgears, motor starters & control wiring) with required size
of copper lugs, nuts and bolts if required.(c) One wire 2.50 sq. mm
97 (e) One wire 6.00 sq. mm 20 Mtr. 62.00 ₹
98 (f) One wire 10.00 sq. mm 20 Mtr. 101.00 ₹
99 Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv grade 30 Mtr. 51.00 ₹
ISI marked copper wires of following size to be erected as directed.(e) 1.50 Sq.mm
core round PVC sheathed
100 Supplying & erecting approved make LAN cable of following size in existing pipe as 150 Mtr. 51.00 ₹
per direction[C] CAT -
101 Supplying & erecting M.S. Box having 16 Gauge painted with red oxide or Heavy 10 Ea. 122.00 ₹
duty PVC box erected flushed on wall or concealed in wall with necessary plastering
& finishing as directed of following size.(d) 250 mm x 300 mm x 75 mm(d)
102 Providing & Erecting 3mm thick Polycarbonate (PC) sheet with grooving as directed 1.5 Sq. Mtr 4648.32 ₹
103 Providing & erecting Switch board for Computer or electric apparatus consisting of 30 Ea. 1262.00 ₹
following modular type accessories mounted with PVC / Metallic concealed/open
box with single mounting base frame covered with textured/metallic /white front
plate,modules erected with necessary connections as directed
1 no. 6A/16A universal plug-switch combined.
3 nos. 6A Switch
3 nos. 6A 5 pin Plug For Modular Type AccessoriesCat. III
104 Supplying and erecting approved make of tube fitting with One no T-5 tube 24/ 28 5 Ea. 560.00 ₹
W with Electronic ballast with each tube separately THD less than 10 & built in
adaptors, GI / PVC housing & mirror optic reflector, suitable to work on 120V -
300V, A.C. supply with connector and adapter if required. [Make of fitting & tube
may be differ& fitting shall be providing with tube]
105 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt 10 Ea. 480.00 ₹
assembled on single MCPCB, with housing used as a heat sink shall be made of thick
sheet Steel conforming to IS: 513/CRCA/ aluminium die cast powder coated and
high U.V. & corrosion resistance with diffuser with company mark/name 160V to
270V, Power Factor more than 0.9, THD < 15%,
CCT 3000 K to 6500K,
Luminaire efficacy> 85 lumens/watt ,LED
LED driver efficiency > 85 %
( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown
ranges of Wattage capacity of LED fittings.The Engineer incharge may select any
wattage capacity between the ranges shown.)(A) Tube Light with integral driver(iv)
22-24 Watts, Surge - 2KV,IP-20, conventional 4 feetCat.III
106 Supplying and erecting led lamps with following wattage capacity of 220 to 240 5 Ea. 145.00 ₹
voltage, minimum 15000 burning hours life, 500 V in built-surge
protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp
(A) LED Lamps integral type, with PC diffuser suitable LAMP holder (ii) 5 to 8 watts
107 Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt 75 Ea. 760.00 ₹
assembled on single MCPCB, with housing used as a heat sink shall be made of thick
sheet Steel conforming to IS: 513/CRCA/aluminium pressure die cast powder coated
and high U.V. & corrosion resistance with diffuser housed in aluminium casted body
with company mark/name
160V to 270V,Power Factor more than 0.9, THD < 15 %,
CCT 3000 K to 6500K,
Luminaire efficacy> 85 lumens/watt
LED driver efficiency > 85 %
( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown
ranges of Wattage capacity of LED fittings.The Engineer incharge may select any
wattage capacity between the ranges shown.)(A) Square/ Circular shaped
Surface/Recessed Mount Downlight with provision for spring loaded mounting clips
complete.IP20(iii) 16-20 watts, Surge-2 KVCat-lll
108 Supplying and erecting LED street light / Flood light fittings with High power White 4 Ea. 7880.00 ₹
LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency more than
130 lm/w and corrosion free High pressure die cast aluminum housing with smooth
finish powder coated and heat sink extruded aluminium with diffuser and
Polycarbonate optics/ lenses, with toughened glass with company mark/name
engraved or embossed 160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT
3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED
driver efficiency > 85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below
description have shown ranges of Wattage capacity of LED fittings.The Engineer
incharge may select any wattage capacity between the ranges shown.)(B) Flood
Light (IP-65), Surge protection -4KV integral and ,Light must have 440VAC line
supply with over-voltage protection.(iii) Above 60 to 90 watts Cat-lll
109 Operational Handle Assembly Complete for(ii) 200 / 250 / 320 / 400 / 630 / 800 1 Ea. 880.00 ₹
110 Operating Shaft (Extensible) for (ii) 200 / 250 / 320 / 400 / 630 / 800 Amps 1 Ea. 180.00 ₹
111 Cable Terminal ( ‘Plain" Type)Set of Four for(i) 32 / 63 Amps 2 Ea. 450.00 ₹
112 Cable Terminal ( ‘Plain" Type)Set of Four for(ii) 125 / 200 Amps 1 Ea. 950.00 ₹
113 providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to 50 Ea. 130.00 ₹
operate on 240 V A.C. system and having breaking capacity 10 KA to be erected in
existing box. confirming to IS 8828/1996 with ISI Mark Cat.III
Sr. No. Description Qty. Unit Rate Amount
114 Providing & erecting 240 V MCB double pole switch for motor & inductive load (C 4 Ea. 385.00 ₹
Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box having
following capacity (B) 40 Amp. Cat.III
115 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) 2 Ea 780.00 ₹
having 10KA breaking capacity & confirms to IS :8828 in existing box having
following capacity (b)40 Amp. (CAT -III)
116 (b)63 Amp. (CAT -III) 5 Ea 860.00 ₹
117 Providing and erecting Sheet Steel powder coated MCB distribution board - flush / 4 Ea. 2732.00 ₹
surface mounted fitted with busbar, neutral link, earth bar and DIN rail, Conforms to
IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate nos. of MCBs.(The
DBs should be used of same company of MCB to be used) suitable for(A) single phase
incoming and horizontal single phase outgoing(b) sheet steel double door (IP-43) (i)4
120 Supplying & erecting Sheet Steel powder coated Cable end termination Box to be 4 Ea. 580.00 ₹
mounted on Top or Bottom of the MCB Distribution Box for housing/covering Extra
wires & Cables, suitable for following size of MCB DB Box. (E) Three Phase 4 Way
121 Providing and erecting Approved make RCCBs conforming to IS: 12640 and having 1 Ea. 3080.00 ₹
sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for
operation on 3 phase and neutral 415V,50Hz. having characteristic of quick action &
tripping with all advance feature & do not incorporate any electronic component for
following Max. rating erected as directed.(ii) 40Amps. FP Cat. III
122 (iii) 63 Amps. FP Cat. III 3 Ea. 3550.00 ₹
123 Providing and erecting Annealed bare Copper wire 8 to 16 SWG. 15 Kg. 928.00 ₹
124 Supplying & erecting earth pit of minimum bore dia.150mm size approved make 2 Ea. 5363.00 ₹
Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of
corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200
Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising,
connection terminal dia of 12mm with constant ohmic value surrounded by highly
conductive compound with high charge dissipation suitable for following type of
applications with chamber and heavy duty cover.(approved make OEM has to submit
test certificate) & having back filling compound of (B) Inner chemical (CCM
Compound)- Resistivity:- 0.2 / meter testing as per IEC 62561-2017, Voltage drop:-
< 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :-
Earthing compound should be capable to retain moisture for long time Necessary
test report must be submitted. (a) For Electrical Installation up to 440V in normal soil
Length of pipe - 1 Mtr
Back filling compound - 1 Nos Bag of 15 Kg.
125 Providing & erecting weather proof, dust & vermin proof, floor mounted front 2 Sq.Mtr 17410.00 ₹
operated indoor type cubical panel board necessary IP-42 and above protection as
per approval from engineer incharge made from 14 SWG thick CRC M.S. sheet for
outer body & doors, 16 SWG thick CRC M.S.sheet for internal partitions with
necessary accesories , supporting angles/ flats channel including cutting, bending,
drilling, welding, riveting with internal partitions & cable alley as per requirements
& instruction of engineer-in-charge with erection
126 Providing and erecting Approved make Four pole moulded case circuit breaker 1 Ea. 18950.00 ₹
having breaking capacity ICU of 35 KA. at 415 V. having Normal current rating
200A.with variable Thermal & magnetic release suitable to work on A.C.supply
c/s. with all internal connections, spreader tinned copper & complete erected in
existing 16 G.M.S.housing ICS=100% of ICU only Cat III
127 Supplying and erecting triple pole & neutral 440V / 500V panel mounting Copper 1 Rn.Mtr 3740.00 ₹
Busbars with four equal Nos. of electrolyte bus having current density not more than
1.6 Amp. / sq.mm (Rated current / cross section area) duly wrapped with colour
insulating tape for phase sequence of following current carrying capacity, erected
with necessary bus bar supports /insulators, main cable socket to each bar, erected
in existing cubical panel with necessary connections.(B) Suitable for 200 Amp.
128 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) 4 Ea. 780.00 ₹
having 10KA breaking capacity & confirms to IS :8828 in existing box having
following capacity (b)40 Amp. Cat.III
129 Providing & erecting 415 V MCB Four Pole for Motor & Inductive Load (C Curve) 3 Ea. 860.00 ₹
having 10KA breaking capacity & confirms to IS :8828 in existing box having
following capacity (c)63 Amp. Cat.III
130 Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase AC Supply 3 Ea. 370.00 ₹
500 V on existing panel board with necessary connections.
131 Supplying and erecting approved make suitable panel indicator LED type lamp, lens 6 Ea. 50.00 ₹
cover, complete erected with necessary connections.
132 Supplying and erecting approved make panel mounting type Digital Voltmeter 2 Ea. 1490.00 ₹
having 3 digits LED display, 0 to 750 AC Volts range erected on existing panel board
with all connection, wiring etc .with manufacturers calibration certificate.
133 Supplying and erecting approved make panel mounting type Digital Ammeter having 2 Ea. 1820.00 ₹
3 digits LED display, external CT operated, calibrated for 0 to 1000 Amps suitable to
operate on 500 Volt AC , erected on existing panel board with all connection, wiring
etc .with manufacturers calibration certificate.
Sr. No. Description Qty. Unit Rate Amount
134 Providing and erecting Approved make Ceiling fan with double ball bearing ISI mark 25 Ea. 1700.00 ₹
with condenser A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy erected on
existing hook or clamp with earthing. [Make shall be approved by Engineer in charge]
135 Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down rod 25 Mtr. 125.00 ₹
erected duly painted for fan complete with proper insulation without leakage and
136 Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the RCC 25 Ea. 125.00 ₹
bars up to 50mm length each side and pierced through a 16 Gauge M.S. box / Heavy
Duty PVC box complete erected concealed in Ceiling with necessary finishing.
137 Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. 25 Ea. 20.00 ₹
138 Supplying & erecting approved make low noise decorative exhaust fan having square 14 Ea. 1990.00 ₹
frame ABS body with inbuilt lowers & square frame.200mm with 1350RPM Cat.II
139 (8) Computer RJ-45 socket Cat.III 30 Ea. 178.00 ₹
140 Providing & fixing concealed wiring for WAN line (internal) with 6 CAT ISI Computer 20.00 Pt. 1374 ₹
cable with separate 1.5 mm thick 1/2" dia. PVC pipe including relevent materials as
per drawing & specification & direction with I/O Socket with box RJ-45 &
labour,wire & Pipe ( Aprox length up to 10mtr) as per instruction of E.I.C etc.
141 Providing & fixing concealed wiring for WAN line (internal) with 6 CAT ISI Computer 15.00 Pt. 2329 ₹
cable with separate 1.5 mm thick 1/2" dia. PVC pipe including relevent materials as
per drawing & specification & direction with I/O Socket with box RJ-45 &
labour,wire & Pipe ( Aprox length up to 10mtr to 20mtr) as per instruction of E.I.C
142 Supplying, Erecting, Testing & Commissioning the passenger / stretcher lift having 1.00 Each 1036486 ₹
following main features: [1] GEAR LESS LIFT DRIVE comprising of High Starting
torque Lift 3 phase 440 V A. C. Permanent Magnet Synchronous motor of proper
rating with high efficiency shall be used. [2] Micro processor based / PLC,
ACVVVF, vector control drive with encoder feedback closed loop system shall be
used for lift car and door operation which shall be full collective selective operation
hall call demand response, UP/DOWN hall stops, Main, Up/ Down Contactor with
overload and phase reversal relay and safety controls.
[3] Car with M S platform with bracings of adequate size and to sustain the impact
load cabin + passenger with safety factor of fire for steel and side panels of Stainless
steel of sheet of grade 304 duty. Car ceiling will be S.S. finishes with aesthetic
appearance with LED ceiling lights. Car flooring shall be of anti skid PVC with choice
of colour of engineer in charge. Car doors shall be of stainless steel grade
hairline finish with centre opening / telescopic automatic doors. Car panel will also
be S.S. 304 finished with emergency stop device, mechanical door safety device,
facility of auto/ attended mode. All car panel buttons and all floor switches must be
with brail language as per lift act. [4] All landing doors must be fire rated for 2 hour
shall be fully automatic centre opening/ telescopic opening made of hairline finish
steel grade of 304 with key holes and infrared curtains with Unlocking facility from
[5] Appropriate battery operated emergency light in the car along with alarm switch
shall be provided. Also, Emergency Light & Fan should start immediately without any
Time Delay as soon as power fails.
[6] Digital scrolling indicator system for up-down arrow along with floor position
indicator shall be provided inside the car and at all floors.
[7] Full height infra red curtain with multiple cross / crossing light beams shall be
[8] Automatic Rescue Device (ARD) shall be provided accordingly of passenger
capacity with Manual Rescue Operation ( Manual Cranking Facility).
[9] Audio visual indication in the lift car showing over loading shall be provided such
that doors kept open till excess load is removed.[10] Spring buffers/PU Buffers shall
[11] Car fan as per passenger capacity with automatic sleep timer shall be provided.
[12] Voice annunciator with suitable music shall be provided in lift car.
[13] Self diagnostics system for operational and safety parameters shall be provided
in control panel.
[14] Mechanical over speed governor with governor calibration as per actual site
parameters and submission of calibration certificate submission, door key holes in
the floor doors, fireman switch shall be provided.
[15] Lift machine hoisting arrangement in the lift machine room and monkey ladder
for lift pit should be provided by the lift agency, along with the other steel structure
works, foundations for the machine etc…
[16] In the hoist way fascia plate shall be provided without any extra cost, where
ever required as / if directed by engineer in charge. [17] Permanent wiring with
necessary safety devices like RCCB in all circuit, Over Voltage Under Voltage
protection and THD eliminator in circuit for lift machine room and lift well with
proper numbers of light points, with fixtures, exhaust fan and plug points shall be
provided by the agency. Only 3 phase Power Supply shall be made available by
department in lift machine room. Necessary Earthing as per Lift Act/Rules shall be
arranged by Lift Agency.
Sr. No. Description Qty. Unit Rate Amount
[18] Any civil/ electrical works for additional and alteration in lift shaft and machine
room related to erection of lift shall be made by lift agency without any extra cost.
(granite/marble fixing around all landing door openings are not in lift agency’s
[19] Agency has to provide all working drawings and documents and liaison services
for obtaining all necessary permission from lift inspector and other authorities.
[20] acrylic transparent licence/display A4 size holder in lift car
[20A] As per statutory requirement of Govt. Of Gujarat lift & escalator act 2000, lift
agency has to provide
1. Car top safety barricade
2. Push & talk communication system.
3. Fireman's switch operation at Ground Floor.
4.carrying out third party lift inspection during/after lift erection and provide
report by third party authorized by concern licensing authority 5.agency has to
provide third party insurance upto completion of free maintenance period and
submit the document for the same.[21] Car Panel Operating Buttons with floor
position indicator/buttons must be of Auto Glow type clearly visible when view from
[22] For Physically Handicapped person Full Length Handrails of hairline finish steel
grade of 304 should be provided at appropriate height on the Rear & Side Wall
Panels in Lift Car.
4/5/6 Passengers, Ground plus 3 upper floors with Rated Speed of 1.0 m/sec.
(B) With General Specification attached herewith. Cat.III
143 Supplying & erecting approved make Lift Announcing solid state system in the 1.00 Each 16950 ₹
Passenger/ Stretcher lifts having AC2/ACVV/ACVF drives & automatic doors only.
The system comprising following features & facilities. (i) Announcing floor message,
message to close period.(ii) Announcing ‘Emergency Message’ when lift is stuck
between floors due to power failure or any other reason. (iii) Instrumental Music
between floor announcing.(iv) Announcement in English / Hindi & Gujarati
Languages. (v) Flexible to accommodate special per programmed message such as
name of the building/office.(vi)Volume adjustment control.
144 Providing & erecting approved make overload non-start feature & overload warning 1.00 Each 32205 ₹
Indicator system in the lift with making use of sound isolated floating platform &
micro switches on SI frame to get sensation of live load inside lift cage at any given
moment, with provides new fixtures of overload warning inside lift cage with new
relay in the existing control panel to activate ‘Overload Non-Start Function with
carrying out additional wiring including laying of new travelling cable, include minor
civil work & without changing the existing capacity speed stops, travel & operation
of the desired lift
145 Providing and erecting Inverter based approved make split air-conditioning unit 6.00 No 63134.00 ₹
consisting of condensing unit with variable speed fan motor, inverter type
hermetically sealed rotary compressor with accessories etc. duly connected
separately erected evaporating unit and blower motor with its accessories by means
of extra supplied proper insulated copper tubing,drain PVC pipes suitable for (Cost
includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS
Stand) with necessary core cutting. (1)For For ISEER Range (KWH/KWH)(4.0 to 4.49)
(C) for 1.7 to 2 ton capacity - Premium Cat.
146 Providing and erecting Inverter based approved make split air-conditioning unit 0.00 No 47780.00 ₹
consisting of condensing unit with variable speed fan motor, inverter type
hermetically sealed rotary compressor with accessories etc. duly connected
separately erected evaporating unit and blower motor with its accessories by means
of extra supplied proper insulated copper tubing,drain PVC pipes suitable for (Cost
includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS
Stand) with necessary core cutting. (1)For 3 Star Rating of current year (B) for
ton capacity - Premium Cat.
147 P/F Mechanical double face movable unit of size 900mm x 2200mm including all 50.00 SQ. Mtr 17662.00 ₹
materials by using 22 SWG mm thick C.R.C.A. steel sheet, 30mm solid round guide
channel press fit in to cold formed 'U' channel made from 14G Thick material, 4 nos.
of C.I. wheels 128mm dia x 35mm, traction chain of 1/2" size, Anti tilt arrangement
on rear side of unit, driving wheel of 3 inseratble arms with central hub, 10 lever
central locking arrangement, Individual unit lock system & stoppers, Indexing
arrangement made of acrylic sheet for numbering and naming.
Powder coating on metal sheet for anti-rust treatment & finishing.
148 P/F Mechanical single faced fixed unit of size 450mm x 2200mm including all 5.00 SQ. Mtr 10093.00 ₹
materials by using 22 SWG mm thick C.R.C.A. steel sheet, 30mm solid round guide
channel press fit in to cold formed 'U' channel made from 14G Thick material, 4 nos.
of C.I. wheels 128mm dia x 35mm, traction chain of 1/2" size, Anti tilt arrangement
on rear side of unit, driving wheel of 3 inseratble arms with central hub, 10 lever
central locking arrangement, Individual unit lock system & stoppers, Indexing
arrangement made of acrylic sheet for numbering and naming.
Powder coating on metal sheet for anti-rust treatment & finishing.
149 P/F Mechanical single face mechanical unit of size 450mm x 2200mm including all 5.00 SQ. Mtr 12061.00 ₹
materials by using 22 SWG mm thick C.R.C.A. steel sheet, 30mm solid round guide
channel press fit in to cold formed 'U' channel made from 14G Thick material, 4 nos.
of C.I. wheels 128mm dia x 35mm, traction chain of 1/2" size, Anti tilt arrangement
on rear side of unit, driving wheel of 3 inseratble arms with central hub, 10 lever
central locking arrangement, Individual unit lock system & stoppers, Indexing
arrangement made of acrylic sheet for numbering and naming.
Powder coating on metal sheet for anti-rust treatment & finishing.
Sr. No. Description Qty. Unit Rate Amount
150 Providing fitting & fixing fully glazed/ partly glazed double leaf anodised 10.00 SMT 7800.00 ₹
aluminium entrance door using extruded section fabricated by standard
manufactures with framing 10.15cm x4.45cm rectangular section with minimum
Thickness 1.95mm & door shutter made from 10.15 cm x 4.45cm aluminium top /
bottom section,Lock rail mimimum 15.0cmx4.45cm & vertical section 4.70 x
cm size with minimum Thickness 1.95mm using 5.5mm thick "Triveni"or HB4 smoke
glass with glazing deep rubber gasket with locking arrangement(Godrej type) with
all fixtures & fastenings of anodised section with aluminium bedding, hydraulic
door closer with all labours & materials etc. Complete as per drawing and as
directed by E.I.C..Item also includes powder coating to alluminium sections of
approved colour / shade incl. all materials,labour,tools & tackles etc. complete.
Supplying, Providing and fixing in position standard table having top surface of
minimum 25mm thick Pre-Laminated MDF Board with one side Pre-lamination and on
other side 0.7mm thick lamination as per specification & as directed by E-I-C, having
necessary provision for wire management data / computer / telephone cabling.
Table having drawer unit of size 400 x 450 X 600mm as per the specification and
design approved by Engineer-in-charge. All supporting system should be matching
with modular partition framing & final finish. Rate is inclusive of KeyBoard tray &
CPU trolley as required.
152 Supplying, Providing & fixing side & back Storage cabinet having Clear inside 5.00 SMT 6956.40 ₹
storable space minimum of 380mm depth. It Should be made from 18mm Pre-
Laminated MDF Board with one side Pre-lamination and on other side 0.7mm thick
Laminate as per specification and as directed by the E-I-C.
153 HIGH BACK CHAIR Providing & Fixing High Back Chair of Overall size- 2.00 Nos. 15000.00 ₹
761W*761D*1127-1302H*431-531SH mm SYNTHETIC LEATHER SEAT/BACK
ASSEMBLY:The Cushioned seat is made of Injection molded Plastic outer & inner.
Plastic Inner is upholstered with leatherette and moulded High Resilience (HR)
Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per
IS:7888 for 25% compression. *Seat SIZE : 47.0 cm. (W) x 48.0 cm. The Cushioned
back is made of PU Foam with insitu molded MS E.R.W Round Tube of size
1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette.*HIGH BACK SIZE:
47.7 cm. (W) x 76.4 cm. The armrest top is moulded from polyurethane(PU) and
mounted on to a drop lift adjustable type tubular armrest support made of
03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish.The
armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO
MECHANISM: The adjustable tilting mechanism is designed with the following
features:• 360' revolving type. • Front-pivot for tilt with feet resting on ground and
continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be
operated in seating position. • 5-position Tilt limiter giving option of variable tilt
angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing is
made up of HPDC Aluminium black powder coated. Seat depth adjustment is
integrated in the seat through a sliding mechanism. Seat depth adjustment range is
of 6.0±0.5 cm. Back Frame is connected to the Up/Dn mechanism housed in Plastic
T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back
support to suit individual need. The pneumatic ht adjustment has an adjustment
stroke of 10.0±0.3 cm. The pedestal is High Pressure Die cast polished Aluminium
and fitted with 5 nos. twin wheel castors. Twin wheel castors are injection
moulded in plastic having 6.0±0.1 cm wheel Diameter and assembled to
pedestal.The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With
castors.)Twin wheel castors are injection moulded in plastic having 6.0±0.1 cm
wheel Diameter and assembled to pedestal.The rate shall include all materials,
hardware and labour etc. complete as per instruction of engineer-in charge and
consultant. Approved Make: Godrej / Herman Miller / Haworth / Knoll.
154 MEDIUM BACK CHAIR Providing & Fixing Mid Back Chair of Overall size- 35.00 Nos. 10000.00 ₹
761W*761D*965-1140H*431-531SH mm SYNTHETIC LEATHER SEAT/BACK
ASSEMBLY:The Cushioned seat is made of Injection molded Plastic outer & inner.
Plastic Inner is upholstered with leatherette and moulded High Resilience (HR)
Polyurethane foam of Density 45±2 kg/m3,and hardness load 16 ± 2 kgf as per
IS:7888 for 25% compression. *Seat SIZE : 47.0 cm. (W) x 48.0 cm. The Cushioned
back is made of PU Foam with insitu molded MS E.R.W Round Tube of size
1.9±0.03cm x 0.16 ±0.0128cm. It upholstered with Leatherette.MID BACK SIZE:
47.7 cm. (W) x 60.1 cm. (D) The armrest top is moulded from polyurethane(PU) and
mounted on to a drop lift adjustable type tubular armrest support made of
03.81±0.03 cm x 0.2±0.01 cm thk M.S. E.R.W tube having chrome plated finish.The
armrest height adjustable up to 6.5±0.5cm in 5 steps. ACTIVE BIO-SYNCHRO
MECHANISM: The adjustable tilting mechanism is designed with the following
features:• 360' revolving type. • Front-pivot for tilt with feet resting on ground and
continuous lumbar support ensuring more comfort. • Tilt tension adjustment can be
operated in seating position. • 5-position Tilt limiter giving option of variable tilt
angle to the chair. • Seat/back tilting ratio of 1: 2 • The mechanism housing is
made up of HPDC Aluminium black powder coated. Seat depth adjustment is
integrated in the seat through a sliding mechanism. Seat depth adjustment range is
of 6.0±0.5 cm. Back Frame is connected to the Up/Dn mechanism housed in Plastic
T spine. It can be adjusted in the range of 7.42±0.5 cm for the comfortable back
support to suit individual need. The pneumatic ht adjustment has an adjustment
Sr. No. Description Qty. Unit Rate Amount
support to suit individual need. The pneumatic ht adjustment has an adjustment
stroke of 10.0±0.3 cm. The pedestal is High Pressure Die cast polished Aluminium
and fitted with 5 nos. twin wheel castors. Twin wheel castors are injection
moulded in plastic having 6.0±0.1 cm wheel Diameter and assembled to
pedestal.The pedestal is 65.0 ± 0.5cm. pitch-center dia.(75.0 ± 1.0cm. With
castors.)Twin wheel castors are injection moulded in plastic having 6.0±0.1 cm
wheel Diameter and assembled to pedestal.The rate shall include all materials,
hardware and labour etc. complete as per instruction of engineer-in charge and
consultant. Approved Make: Godrej / Herman Miller / Haworth / Knoll. Synchro
mechanism with single,position locking arrangement,Adjustable arms with PP pad,
Powder coated black sigma metal base.
155 LAW BACK CHAIR/NON REVOLVING VISITOR CHAIR. Providing & Fixing Visitor Back 65.00 Nos. 6000.00 ₹
Chair of Overall size- 550W*580D*840H*450SH mm Cushion Chair :The seat and back
are made up of 1.2 ±0.1em. thick hot pressed plywood measured as per QA method
described in OCP-QLTA-P14-18 and upholstered with fabric and moulded
Polyurethane foam with PVC lipping all around. The back foam is designed with
contoured lumbar support for extra comfort..(LOW BACK) SIZE: 49.5cm. (W) X
45.5cm. (H)*SEATSIZE: 49.5cm.(W)X 43.0cm. (D) The HR polyurethane foam is
moulded with density =4S+/-2 kg/m3and hardness load 16 ± 2 kgf as per IS:7888 for
2S% compression.The one-piece armrests made of black integral skin polyurethane
with SO-70Shore Hardness and reinforced with M.S. insert. The armrests are scratch
and weather resistant. The armrests are fitted to the seat with seat armrest
connecting bracket made of 0.3 ±0.022cm. thk. HR steel.The understructure is
±0;03cm. x 0.2 ±0.016cm.thk., M.S;E.R.W. tube and black powder coated ( DFT 40-
60 microns).The rate shall include all materials, hardware and labour etc. complete
as per instruction of engineer-in charge and consultant.
156 Supplying,providing and arranging in posiotion wooden sofa made with minimum 5.00 Nos. 17400.00 ₹
19mm.ply structure and internal frame work made of C.P teak/marandi wood seat
made with minimum 19 mm ply and cushion made with foam 100mm.thick,32
density on seat covered with 14mm.thick 18 density form,back made with wooden
frame of minimum 50mm*40mm with 4mm ply and covered with foam 150mm,32
density with 18 density 14 mm thick foam for back extra support to the shape all
foam of seat and back covered with tapestry etc.as per specic ao n and as approved
by E-I-Charge.clear inside length of 6.0 running feet for three seater sofa.
157 Conference room 36 seater table----Providing and Placing in position Conference 1.00 No 442483.00 ₹
table for 36 persons of overall size : 10800mm (W) x 1800mm (D) x 750mm (H) and
having One 3 Seater Head Module of size 1800mm x 850mm x 750mm and 8 Nos
Seater Modules of size 1350mm x 710mm x 750mm. The worksurface shall be 36mm
thick MDF board with one side pre-laminated board conforming to IS:14587 and
0.4mm thick PVC membrane pressed on the top and having chamfered edges. Full
length access panel is provided with soft closing hinges inline with worktop edge.
The understructure and modesty consists of mixture of 18mm and 25mm thick pre-
laminate twin board of E1-P2 grade and conforming to IS: and 25mm thick pre-
laminate twin board of E1-P2 grade and conforming to IS: and 25mm thick pre-
laminate twin board of E1-P2 grade and conforming to IS: 12823, edge banded with
2mm thick pvc lipping. Aluminium alloy of grade 63400 WP is used for connecting
panels together. An array of panels made of 0.8mm and 1.2 mm thick CRCA MS
sheet as per IS:513, epoxy powder coated (DFT 40-60 microns) is used for flow of
wires and cables. The table shall have provision to mount AV/HDMI/VGA cables and
shall come with cable retractors.Additional wire cover made of 0.8mm thick CRCA
MS sheet as per IS:513 shall be provided below the worktop to conceal microphone
wires running from table top to wire tray. Company is ISO-9001:2015,ISO-
14001:2015,ISO-45001:2018,Greenguard(UL), BIFMA and AIOTA certified.Product
Certificates:GRIHA, Greenguard (UL), GreenPro, SCS Global IAQ - Gold.Completa all
as per the Direction of Engineer in Charge.
158 Providing and Placing in Position High Back Chair. The cushioned seats shall be made 1 No 62950.00 ₹
of injection moulded plastic outer and inner. Plastic inner shall be upholstered with
pure leather and moulded high resiliance polyurethane foamof Density = 45±2
kg/m³, and hardness load 16±2 kgf as per IS:7888 for 25% of compression. Seat size
shall be 47.6 cm W x 49.2 cm D. The back shall be cushioned and shall be made up
of PU foam with insitu moulded MS ERW round tube of size 1.9±0.03 cm x
0.16±0.0128 cm, upholstered with pure leather. Back size shall be 47.5 cm W x
cm D. The armrest top shall be moulded from polurethane, and shall be upholstered
with pure leather and mounted on ot a drop lift adjustable type tubular armrest
support made up of Ø3.81±0.03 cm x 0.2±0.01 cm thick MS ERW tube having chrome
plated finish. The armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. The
adjustable tilting mechanism shall be designed with the following features : 360°
revolving type, front-pivot for tilt with feet resting on ground and contionuous
lumbar support ensuring more comfort, Tilt tension adjustment can be operated in
seating position, 5-position tilt limiter giving options of variable tilt angle to the
chair, seat/backtilting ratio 1:2, the mechanism housing is made up of HPDC
aluminium black powder coated. Seat depth adjustment shall be integrated in the
seat through a sliding mechanism. Seat depth adjustment range shall be 6.0±0.5 cm.
Back frame shall be connected to the up/down mechanism housed in plastic T spine.
It can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to
suit individual need. the pneumatic height adjustment shall have an adjustment
stroke of 10±0.3 cm. The pedestal shall be high pressure die cast polished
aluminium and fitted with 5 nos. of twin wheel castors. The pedestal shall be
65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection
moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal.
Sr. No. Description Qty. Unit Rate Amount
159 Providing and erecting Inverter based approved make split air-conditioning unit 0.00 No 47780.00 ₹
consisting of condensing unit with variable speed fan motor, inverter type
hermetically sealed rotary compressor with accessories etc. duly connected
separately erected evaporating unit and blower motor with its accessories by means
of extra supplied proper insulated copper tubing,drain PVC pipes suitable for ( cost
includes Eco Friendly green gas charging and 15A plug top & Remote Control & MS
Stand) with necessary core cutting. (C) for 1.7 to 2 ton capacity - Premium Cat.
160 Hiring of Architech Agency for Structural Design of working plan, check stability of 1.00 Job 95000.00 ₹
structure according to submit for approval to UGVCL. Also submit Provide AutoCAD &
PDF drawings, structural design of extended 3rd floor, Bar bending schedule with
detail specifications.
161 Full HEIGHT PARTITIONS OF 2100MM HEIGHT. Providing and fixing Aluminum 35.00 SMT 3682.92 ₹
partitions of minimum 60 to 70 mm thickness having framework of 1.2 mm thick
aluminium extruded section and removable tile base system including necessary
wire management system as per specification & as directed by E-I-C.
162 2 mm Aluminium/4mm ACP sheeting fixed with type-4 class-B High intensity grade 110.00 SMT 3955.08 ₹
sheeting as per IRC 67:2012 reflective sheeting of size including lettering and signs
163 Providing and fixing 12 mm thick fully toughened glass door shutter (full glass door), 65.00 SMT 17005.48 ₹
comprising clear toughened glass of approved make, machine polished edges, with
approved quality frosted film and required symbol/design as directed by Engineer-in-
Charge, complete.
The glass door shall be fixed with suitable heavy duty SS patch fittings / top &
bottom pivot arrangement / floor spring (as required), including necessary gaskets,
bushes and all fixing accessories complete.
Providing and fixing 18 mm thick plywood frame cladding, extended on wall from
door opening on all sides, including necessary wooden support members, adhesives,
screws and anchoring arrangements. The plywood surface shall be finished with
matching natural veneer and PU polish complete.
Including providing and fixing:
• Heavy duty SS patch fittings / pivot set suitable for 12 mm toughened glass door
• SS D-type handle / glass door handle (both sides)
• Floor spring / heavy duty hydraulic door closer (ISI marked) suitable for glass door
• All necessary holdfasts, screws, sealant, adhesives
• Cutting and making good the walls
Complete in all respects as directed by the Engineer-in-Charge
164 Providing and fixing 35 mm thick factory made solid core flush door shutter finished 25.00 SMT 12053.38 ₹
on both faces with 0.6 mm thick natural decorative veneer of approved shade and
make, including necessary hardwood edge lipping and finished with PU polish
The door shall be provided with vertical vision panel fitted with 5 mm thick frosted
/ etched toughened glass including wooden beading and rubber gasket complete.
Providing and fixing 18 mm thick plywood frame cladding, extended on wall from
door opening on all sides, including necessary wooden support members, adhesives,
screws and anchoring arrangements. The plywood surface shall be finished with
matching natural veneer and PU polish to match the door shutter, complete in all
Including providing and fixing:
• 3 Nos. heavy duty SS butt hinges
• Mortise lock with handles
• Heavy duty hydraulic door closer (ISI marked) suitable for 35 mm thick wooden
• All necessary holdfasts, screws, adhesives
• Cutting and making good the walls
Complete in all respects as directed by Engineer-in-Charge.
165 Dismentling doors, windows, ventilators etc. (wood or steel) shutters including 3.00 Each 254.93 ₹
chowkhats architraves, holdfasts and other attachment etc. complete and stacking
them within all lead and lift.(ii) Exceeding 3 Sq.M. in area.
166 ACOUSTIC WALL PANELLING: Providing & fixing of panels - 95.00 SMT 5300.00 ₹
1200mmx2400mmx15mm thickness, NRC = 0.90, Resistance to fire : REI 90 made out
of mineral fibre. Panels to be fixed on framework made out GI (0.60mm thick &
60mm width) sections to form a section of 600mm x 600mm. Panels to be
fixed on the Slabs with a minimum of 50mm to 100mm void or gap with
Galvanized screws of length 50 mm & Dia 4.5 mm.In case of islands - vertical
shall be provided with metal section all 4 sides. In case of wall to wall, wall angle
shall be provided towards the wall or UD section shall be provided which shall
be concealled as per the architects design.
A ESTIMATED COST - RS = ₹
B Bidder’s Offer (+ / -) in % ------------- [B]
C Grand Total C = A +/- (A*B)]
C Grand Total C = A +/- (A*B)]
D Add 1% Welfare cess on C
E Total including Welfare Cess ----- D = C + D -------------------------------
F Goods & Service Tax F = E x GST% i.e. 18%as applicable on the date of tender in amount Rs.
G Grand Total including Welfare Cess & GST ---- G = E + F ----------
G Grand Total including Welfare Cess & GST ---- G = E + F ----------
Final Offer (in Rs.)
Final Offer (Rs. In Words)
We have read and clearly understood the terms, conditions, Schedule ‘B’ and Technical specifications put up by UGVCL on WEB site.
I/We hereby accept all the conditions and specifications of this tender document, and accordingly, I/We am/are willing to carry out the work at
quated rate as above.
SIGNATURE OF CONTRACTOR Chief Engineer (Operation)
(With rubber stamp/seal of the company) UGVCL R.O. MEHSANA
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
RAW_HTML
3rd Floor ugvcl.pdf
Price Bid Extension R and C Office.pdf
Draft Tender Notice- Extension.pdf
Tender Notice Extension R and C Office.pdf
Download all tender documents and submit your bid