Special repair to Bldg no P101 1 to 4 Type II MD Accn at MES Colony at Ahmedabad cantt

Amount

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.,) or insulation boards/slabs/blankets, any thickness, including cover fillets

S&F mild steel rolled sections as in framing for fixing AC boards in ceiling and the like fixed with angle cleats and connecting plates of grade Fe-410-W (Gde-E-2500 quality-A-.

S&F Tee grid suspension system of size 600 mm x 600 mm type-1 made out of roll framed hot dipped galvanised steel zince coated of not less than 120 gm/Sqm, main runner 0.3 mm thick of section 24 mm x 33 mm crross runner 0.30 mm thick of section 24 mm x 25 mm, wall angle shall be 0.63 mm thick of section 24 mm x 24 mm grid shall be suspended by 4 mm dia adjustable quick fit hanger rod, system exposed portion shall be pre painted polyester coated in off whitee/white in colour complete with material, fixing, jointing etc., with Coloured textured designer ceiling board (Everest)/Asbestos Cement white fiber Board 4mm thick of size 595 x 595 mm fixing with screws/clips complete all as per manufacturers instructions and direction.

Dismantling asbestos cement (corrugated or semi corrugated, etc)sheets in roof covering complete all as specified.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of colour as approved by GE and having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified specified

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of colour as approved and having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified specified

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise as dircetd and as specified.

Roughening the surfaces of old concrete floor by picking, sweeping, cleaning and washing down with water to remove dust and brushing neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and directed

M&L for 25 mm thick PCC type B-0 (1:2:4) using 12.5 mm aggreage as in floor finished even and rough to received top layer or tiling complete all as specified.

M & L for non skid ceramic (colored), 7 to 8 mm thick as in floor area of each tile exceeding 0.6 Sqm but n exceeding 0 .11 Sqm , set and jointed in neat cement slurry and pointed in white or colored cement to match incl and over screed bed or beeding layers of mortar 15mm thick in CM 1:4 in floors, complete all as specified and directed. complete all as specified and directed.

M&L for Glazed ceramic tiles coloured (300x450mm) x 7mm thick, in wall/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick backing coat of tiles in CM (1:3) complete all as specified

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 15mm thick in CM 1:4 screed bed all as specified.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match incl 10mm thick backing coat of tiles in CM (1:3) complete all as specified

M&L machine cut Kota stone slab 20-25 mm thick as in flooring or trades of step incl half round moulding over and including screed bed 20 mm thick in CM (1:3) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified.

M&L machine cut Kota stone slab 20-25 mm thick as in riser to step including 10 mm thick rendring in CM (1:3) laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete all as specified.

Demolition of stone slab and tiles of any description or thickness as in floors, apron etc laid, bedded and pointe in any mortar complete all as directed.

M&L Udaipur Green marble 18-20 mm thick laid and jointed with grey cement slurry over and including 20 mm thick CM 1:3 screed bed complete all as specified and directed.(Note: All exposed side of stone slab to be rounding)

Removing of existing unserviceable water proofing treatment with PCC padding, taking down cement plaster etc of any description and cleaning of top surfaces of cement concrete flushing out junction of parapet walls and washing down with water complete.

M&L for water proofing treatment to non assessible RCC roofs by providing 10mm thick screed in CM 1:3 mixed with water proofing compound @3% by weight of cement & applying one coat of bitumenous primer @ 0.30 kg/sqm & laying APP based polymeric modifed membrane with polyster non woven reinforced of weight not less than 3kg/Sqm of 3 mm thick with polythene finished sealing with side overlaps of 75mm & 100 mm laps at the ends of membrane by torch application method & applying two coats of aluminium paint 0.2 litre /sqm as per the makes approved by the Engr-in-Charge. Note: WPC shall be measured and paid sepratly

Supply only integral water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed

M&L for pre Polished Chequered cement concrete tiles 30cm x 30cm x25mm thick on horizontal surfaces,set, jointed and pointed in neat cement slurry in floors incl 15mm thick screed bed CM 1:6.

Dismantling water tanks and removing to store of capacity exc 250 & n.exc 500 ltrs.

S & F 500 ltrs rotational moulded polyethelene water storage tanks (cyclindrical vertical with closed top) incl connecting up pipes securing access covers etc as specified and as directed(Make : Sintex or Polycon).

M&L for PCC (1:3:6) Type C-2 with using 40mm graded stone aggregates as in platform for PVC tank all complete as specified and as directed.

S&F 20 mm dia PVC ball cock (PVC float valves) complete high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exc 10 cm girth complete all as specified and directed

Taking up or down GI tubing 15mm bore pipe and connection including cleaning for refixing or removal from site as directed

S&F 15mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed.

Taking up or down GI tubing 20mm bore pipe and connection including cleaning for refixing or removal from site as directed

S&F 20mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed.

S&F Butt hinges, Medium weight, cold rolled mild steel, and fixed 100mm size

M&L for PCC 1:2:4 type B0 using 12.50mm graded stone aggregate in roof etc. as levelling coarse etc. all as specified and as directed by Engineer-in-Charge

Taking down cement plaster on wall of any description including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed.

M&L for rendering on fair faces of brick work in two layers i.e., 15 mm thick in CM 1:4 mixed finishing the surface fair and even without using extra cement complete all as specified and as directed.

M&L for preparation of new plastered surfaces on walls and applying two coats of cement based paint over one coat of Primer on walls complete all as specified and directed.

Complete removal of existing treatment of old plastered surfaces of walls and applying two coats of cement based paintover one coat of Primer on walls complete all as specified and directed.

M&L 10mm thick rendering in cement mortar 1:6 on other than fair face of brick work or concrete surface complete all as specified and directed.

M&L newly plastered or un plastered surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and directed

Complete removal of existing treatment of old plastered surfaces of walls and applying two coats of oil bound distemper over and incl one coat of wall care putty on wall surface complete all as specified and directed..

M&L for rendering 5mm thick plastering in CM (1:3) on ceiling, soffits of slabs, chajjas, columns and beams etc and finished the plastered surface even and smooth without using extra cement.

M&L preparing newly plastered or unplastered surface of ceiling and applying three coats of white washing complete all as specified and directed.

M&L complete removal of existing treatment of ceiling and applying three coats of white washing complete all as specified and directed.

Demolition of brick work built in cement mortar of any description.

M & L for brick work with sub class ‘B’ old size bricks, straight or curved on plan and any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

M&L brickwork with sub class B bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 by using old size bricks complete.

S&F in repairs vitreous china wash basin, white, flat back, size 550x400m excluding taps, waste , chain & plug & porcelain stopper including brackets incl cutting for pinning in ends of bracketes or erecting stand and fixing and supply and waste pipe complete all as specified and directed

S&F in repair 10 ltr capacity PVC flushing cistern low level white colour incl PVC connection PVC flush pipe of reqd length complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580x440mm white with integral foot rest complete incl provision of lime concrete bedding.

S&F in repair 15 mm bore angle cock with flage complete all as specified and direcrted.

S&F in repair CP towel rail complete all as specified and directed.(Cat part No BA-40 of Make-Prayag or its equivalent make).

S & F in repairs chromium plated soap dish complete all as specified.(Cat part No BA-45 of Make-Prayag or its equivalent make

S & F in repairs corner glass shelf 300mm complete all as specified (Cat part No BEA-46 of Make-Prayag or its equivalent make

S&F 0.63 mm thick stainless steel plate rack of size 31"x36"x10" complete all as specified and directed.(Cat part No 348 of Make-Prayag or its equivalent make

S&F in repairs Bib taps (long body )fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified and as dierected.

S & F in repair 15mm bore PVC Connection with PTMT nut of length 450 mm complete all as specified and directed

Supply only pillar taps, cast copper alloy with capston heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore.

M & L 75mm thick plain cement concrete type D-2 1:4:8 (40 mm graded stone aggregate) as in sub base complete all as specified and directed.

S&F in repair brass CP shower rose 125 mm size with or without swivel joint and fixing to steel pipe

S&F in repairs stop valves fancy type cast copper alloy, chromium plated with long shank and cup (concealed type) for 15mm bore pipe, screwed both ends including necessary fittings such as sockets for pipe or for union all complete as specified and as directed. .

S & F in repair Grating doom 125 mm dia with waste hole of PTMT (Minimum weight 40gms)

S& F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed.

Supply and fixed in repairs sinks with drainage board made of stainless steel 1mm thick sheet plugs, washers and waste pipe, including a pair of cantilever brackets embedded in wall with suitable size of PCC (1:3:6) type C-1 blocks and connecting union to pipe of overall size 915mm x 460mm & bowl size 410mm x 330mm x 160mm all complete as specified and as directed.

Dismaintling of 75mm to 100mm bore cast iron pipe jointed in cement mortar and taking out of trenches or any description and any position as required complete all as specified and directed.

S&F of 100mm bore cast iron soil , waste and vent pipe, sand cast, in any length , with or without ears , with cement joints in cement sand mortar 1:1 with spun yarn fixed to wall complete all as specified and directed.

S & F cast iron soil, waste and vent pipe, sand cast 75mm bore in any length, with or without ears, with cement joints in CM 1:1 with spun yarn fixed to over septic tank or soakage well complete all as specified and directed

S&F PVC(SWR) 75 mm dia soil waste and rainwater drainage pipes (6 kgf / sqcm) single socketed in any length with rubber ring joint laid in floor or fixed on wall all as spd & directed.

S & F PVC (SWR) bends any radius 75mm with access door

S&F of 100 mm bore cast iron bend/TEE (any Radius) diminishing pieces or tapers (Large bore measured) complete all as specifed and directed.

S&F of 100 mm bore cast iron branch pipe , single (equal or unequal), ordinary or inverted (Spigot or Socket type ) or with parallel branches complete alla specied and directed.

S&F of 75 mm bore cast iron bend (any Radius) diminishing pieces or tapers (Large bore measured) complete all as specifed and directed.

S&F of 75 mm bore cast iron cast iron cowls complete all as specifed and directed.

Taking down chowkat with shutter exc 1.5 sqm and n. exc. 4.00sqm each and removing from site.

Taking down chowkat with shutter n. exc. 1.5sqm each (without taking off shutter from the Frame).

S&F mild steel angle iron work as in doors frames, chajja hollow square sections conforming to 410W(Gde E-250) quality-B including fixing of holdfast and hinges complete all as specified

S&F factory made 35 mm flush shutter, solid coare construction, with block board core and plywood face panel, commercial type on both side etc complete all as specified and directed.

S&F factory made 35 mm thick 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated sash members, any numbers and mited beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.20(a) supplied and fitted to chowkats

S & F stainless steel wire cloth 0.36 nominal dia wire & average width of aperature 1.40 mm fixed with stainless steel wire staples complete all as specified and directed

S&F 200 mm long Aluminium anodised barrel tower bolts.

S&F 150 mm size aluminium anodised door handles.

M&L for sliding door bolt of 300mm long plate Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F 300 mm ordinary mild steel rat tail rod pattern spring incl roller and roller plate complete all as specified and directed

M&L for preparation of new wooden surface of any description n. exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of primer.

S&F Factory made solid panel pace door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

Solid PVC door frame of size 50x47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, supplied and fixed in repair in opening as per specification and drawing complete as directed.

S&F in repairs 18 mm (+ 0.7 mm) thick, solid PVC sheet one side prelam sheet for cupboard shutter of density 600 Kg/Cbm bent 900 and finish at all edges at level for making egdes at level for making edge lipping/bending or 0.5 mm thick PVC sheet lipping at 4 edges using bonding tape etc complete all as per direction of Engineer-in-Charge and manufacturer specification.

S&F stainless steel butt hinges medium weight 100 mm long complete all as specified and directed

S&F 125 mm long Aluminium anodised barrel tower bolts complete all as specified and directed.

S & F powder coated anodised Aluminium alloy sections sliding windows with frames Series-B (18 mm) and , 3 track sliding shutters duly fitted with neoprene beading, glazing clips, two shutters tinted glass panes 4.80 mm nominal thickness one shutter with stainless steel wire cloth 0.36mm dia and average width of aperture 1.4mm , aluminium alloy handles etc. complete all as specified and directed. Note :Rates include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, handle with or without opeing for AC as directed by EIC etc

S&F aluminium anodised ventilator with fixed aluminium frame of size 65 x 40 x 1.98mm thick fixed in vertical position with aluminium vertical members and half portion to be provided with 4mm thick pin head glass and remaining portion to be louvered using 4mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm incl necessary channel frame work, including rubber gasket and aluminium beading complete all as specified.

S & F of mild steel work such as window guard bars and similar work conforming to Fe – 290 Grade – E 165 complete all as specified and directed.

S&F in repair repair 25 mm dia drapery rod fancy powder coated fixed to wall with bracket & knobs complete.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth not otherwise described applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

S&F 100 mm size aluminium anodised door handles.

M&L 75mm thick PCC (1:3:6) type C2 as in plinth protection/footpath using 40mm graded stone aggregate finishing cement concrete surface even & smooth without using extra cement including impression and glass strip or bitumen filling in two panel etc complete all as specified and as directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including reinforcement cut as required to facilitate demolition complete all as specified and directed

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe-290 (Gde E- 165)complete all as specified and directed.

S&F 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed

S&F of 75 mm bore cast iron branch pipe , single (equal or unequal), ordinary or inverted (Spigot or Socket type ) or with parallel branches complete alla specied and directed.

S & F Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4)

Treating the soil under plinth protection/floor at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed

Taking down carefully surface aluminium or copper point wiring with PVC casing-caping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete.

Point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for mounting switches, sockets, fan regulators complete for the following :-

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One socket outlet 6 amp controlled by one switch on the same board with other switches.

(d) One socket outlet 6 amp controlled by one switch on indepdendent board.

Point wiring with 1100 volts grade PVC insulated FRLSH multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 2.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal box of thickness not less than 1.2 mm covered with 3 mm thick phenolic laminated white sheet cover for one 16 amp socket outlet controlled by one switch on independent board complete.

S&F switch piano flush button single pole one way 6 amp complete.

S&F switch piano flush button single pole one way 16 amp complete.

S&F socket outlet 2 in 1, 3 pin 6 & 16 amp flush type complete.

S&F socket outlet 2 in 1, 2 & 3 pin, 6 amp, flush type complete.

S&F hum free electronic step fan regulator 120 - 280 volts of 100 watt capacity including connecting up complete.

S&F ceiling rose 6 amp, 3 plates polycarbonate body complete.

S&F LED batten (1.2 m) made of PVC housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficacy of 100+ lumens per watt and total power consumption not less than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD < 10% and PF > 0.95 complete. Make : Philips cat ref no. ENDURALED BATTEN " BN 108C LED 20S PSU CDL WH " or Havells Lumiline plus as approved.

S&F LED bulkhead fitting 9 watt IP 66 & IK 09 with pressure diecast aluminum housing & polycarbonate diffuser duly prewired for connection with flexible multi stranded copper conductor cable as required all as per Philips cat ref no. WT202W LED6S CW PSU S1 PC or equivalent in Wipro or Bajaj or Havells as approved.

S&F air ventilation fan 250 mm in toilet in rectangular in shape, PVC body, white colour 230V including louber shutter complete all as specified and directed.

S & F LED fixtures 10 watt including connection aving a nominal system lumen output of 1200 lumens at a minimum system efficacy of 100+ lumens per watt and it should have a color temperature of 6500K, CRI>80, THD < 10% ,PF > 0.95 and surge protection upto 4 kV complete.

S&F ceiling fans complete with blades,down rods,electronic regulator and accessories, , 230 volts, 1200 mm sweep,min air delivery 210 CFM with service value 6.00 BEE,five star rated with brushless direct current motor (BLDC) complete all as specified and directed

Supply & fix exhaust fans AC single Phase 230/240 V of size 300 mm sweep with louver, metal body.

GIRNAR CONSTRUCTION

TECH SERVE SOLUTIONS

SNEH TRADERS

Shreeganesh Construction

SANVI ASSOCIATES