SPL REPAIR TO BLDG NO P 05 OF HQ 39 MTN ARTY BDE AT ALHILAL MIL STN

Amount

Taking down existing water proofing treatment (if any) including cleaning with wire brushes roughening the surface and hacking out dirt, where directed and disposal of rubbish not exc 500m distance from the starting point complete all as specified and directed.

M&L 15mm thick (average) plaster in CM 1:3 in order to maintain proper slope and base over existing roof surface for laying APP based polymeric membrane, mixed with water proofing compound as per manufacturer's instructions finished even and smooth without using extra cement complete all as specified and directed. Note: WPC and polymeric membrane shall be measured and paid separately.

M&L PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in roof kerbs, mud tops, roof padding etc complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L APP (Atactic Poly-propylene polymer) modified membranes, five layered, 3mm thick weighing not less than 3.6 kg/sqm, having a centre core of polyester non-woven mat (FP) reinforcement dipped into APP modified mix and sealing all the over laps 75mm on length side and 100mm on width side of membranes by torching as per manufacturer's instructions by authorised applicator only after applying evenly a coat of bitumen VG-10 grade @ 1.20 kg per sqm on the bottom of APP and on top of joints of APP complete all as specified and directed.

M&L rendering 15mm thick plaster in CM 1:4 on fair faces of brick work/stone masonry finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10mm thick plaster in CM 1:6 on fair faces of brick work/stone masonry finished the surface even and smooth without using extra cement complete all as specified and directed.

Rendering 5mm thick plaster on ceiling in CM 1:3 finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L repairing the edges/corner of chajja/roof projection and similar work by removing the plaster width/girth exceeding 15cm & not exc 30cm making good with 15mm thick rendering in CM 1:3 to match with including chicken wiremesh netting on existing surface complete all as specified and directed.

M&L preparation of newly plastered or unplastered surfaces of walls and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/ltr, of approved manufacturer, of required shade and colour complete as per manufacturer's specification. Two or more coats on new work, over a coat of wall care putty 2mm thick, complete all as specified and directed.

M&L preparation of old plastered or unplastered surfaces of walls and applying two coats of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/ltr, of approved manufacturer, of required shade and colour complete as per manufacturer's specification. Two or more coats over a coat of wall care putty 1mm thick, including complete removal of existing treatment of wall surfaces complete all as specified and directed.

M&L applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces of wall complete including preparation of surfaces of walls complete all as specified and directed.

M&L applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over old surfaces of wall complete including preparation of surfaces of walls by complete removal of existing treatment complete all as specified and directed.

M&L preparing newly plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

M&L preparing old plastered surface of ceiling and applying two coats of white wash complete all as specified and directed.

Demolition of cement concrete unreinforced in ground floors, kota stone, granite flooring, tiles flooring and paving's not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L Glazed ceramic coloured tiles in vertical surface 350mm x 250mm x 7mm/450mm x 350mm x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match as in skirting/dado etc. laid over and including 10mm thick backing coat in cement mortar 1:4, set and jointed in neat cement slurry and pointed with coloured to match the tiles complete all as specified and directed.

M&L Non-skid, coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 sqm but not exc 0.11 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:4, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed.

M&L Non-skid, coloured/digital ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.18 sqm but not exc 0.38 sqm as in floors etc laid over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointed with white or coloured cement to match the colour of tiles complete all as specified and directed.

M&L 18 to 20mm thick granite (of any type) tiles, bedded and jointed with grey cement slurry and pointed with white cement (1:2) with admixture of pigment to match the shade of granite stone incl grinding and polishing complete over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 25 mm thick PCC 1:2:4 type B-0 (12.50mm graded stone aggregate) as in leveling course of flooring or roof complete all as specified and directed

M&L 50mm thick PCC 1:3:6 type B-1 (using 20mm graded crushed stone aggregate) as in plinth protection/footh path finished the surface even and smooth without using extra cement complete all as specified and directed.

M&L coloured chequered cement concrete tiles, machine pressed, factory made of size 200x200x25mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and incl 15mm thick screed bed in CM 1:6 complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) n. exc. 1.5 sq.m each complete all as specified and directed.

Taking down chowkats or frames but with shutters (with out taking off shutter from the frames) exc 1.5 sq.m but n. exc 4 sq.m each, complete all as specified and directed.

Taking down shutter of any description exc 1 sq.m but n. exc 2 sq.m each. complete all as specified and directed.

S&F pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and tarring back side of frame, complete all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates,rails, braces, etc., complete,drilling for fixing of steel sheeting or other covering. doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rail and guides) and hanging;also fastening and fixing conform to Fe-410-W Gde E-250 complete all as specified & directed.

S&F, solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. square tube, supplying and fixing in opening as per specifications & directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat molded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement complete all as specified & directed.

S&F 100 mm size aluminium butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin ,anodised, type B-21 complete all as specified and directed.

S&F 100 mm size (length of bolt) aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size (length of bolt) aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 300 mm size (length of bolt) aluminium alloy, anodised, sliding door bolt with hasp and staple ,(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F 100mm size aluminium locking bolts, anodised with bolt less than 10mm dia complete all as specified and directed.

S&F 35mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides with both face covered with decorative face veneer with lipping/frame to match complete all as specified and directed.

S&F aluminium anodised powder coated door/window shutter of aluminium coating 50 micron and aluminium section weighing 0.55 Kg/m including necessary joining cleats, glazing clips, rubber neoprane packing, handles 2 Nos in each door, hinges, door stopper, anodised aluminium snap beading screws etc complete all as specified and directed.

S&F anodised aluminium frame for doors, windows, ventilators with minimum thickness of powder coating 50 micron with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F 6mm thick PVC decorative sheet, white/coloured for aluminium door shutter complete all as specified and directed.

S&F 10mm thick toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required complete all as specified and directed.

S&F 18/19mm thick veneered particle board, solid core, interior grade, with decorative face veneers one face complete all as specified and directed.

M & L second class soft-wood plain fillets square/rectangular, wrought face of sectional area exc. 13 sq.cm but not exc. 25 sq.cm securing with screw complete all as specified & directed.

S&F aluminium (extruded section body) door closer hydraulically regulated, designation No. 3 universal type suitable for door shutter of 851 to 1000mm in width and of weight between 61 to 80 Kg complete all as specified and directed.

S&F box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick MS tube factory made with double side shutters wire gauged shutters & glass glazed shutter(wire and glass panes shall be measured and paid separately) with side hung shutters with steel handles and steel peg stay doytailed at welded incl 2 Nos tower bolts 150 mm long for each leaf and 8 mm square bar grills at spacing as shown on drg welded to FI frame work,incl other fittings,hinges,handles tarred hold fast PCC blocks etc. all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 ,complete all as specified.

M&L preparing new surface of steel of any description, over 10cm width or girth not other wise described and appliying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames,metal frames including punching or drilling out old glazing pins/spring clips , or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc. 0.5 sq.m in each pane complete all as specified and as directed.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Dismantling of old rested plain or corrugated steel sheeting, any gauge, thickness,including Nainital or similar pattern roof covering etc. complete all as specified and as directed.

M&L pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, facia and fixed with self tapping screws as specified. (Colour as approved by GE)

S&F mild steel joist, channel, angle or tee sections, fixed independently, without connecting plates etc. gde Fe 410-W (Grade E-250) quality B complete all as specified and directed

S&F rolled mild steel bands,straps,supports or stays for rainwater,ventilating pipes,including bolts,if required; hooks(stays),heavy,for large gates,hook and pintle hinges;large hasps and staples;chains;hand made sliding bolts;clamps;hold fasts;wall ties;hooks for hanging fans;plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way adn three way straps, plate washers and similar small articles conforming to Fe-290 Gde E-165 complete all as specified & directed.

S&F cutting holes into or through cement concrete slabs, chajjas etc reinforced or otherwise not exc 100 sqcm complete all as specified and directed.

S&F plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,without any attachment complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc but excluding ashlar facing, dressed stone work precast concrete articles complete all as specified and directed.

M&L brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6, complete all as specified and directed.

All as per item No. 59 here-in-above but except brick.

M&L walling of random rubble, un-courses, well bonded bedded & solidly hearted built in cement mortar 1:6, complete all as specified and directed.

All as per item No. 59 here-in-above but except stone.

S&F fancy type, chromium plated, bib tap, cast copper alloy with crutch or butterfly handle, screwed down, screwed for 15 mm bore iron pipe or for brass ferrule complete all as specified & directed.

S&F CP swan neck type pillar taps fancy type 15mm bore cast alloy with capasten head screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and flynuts screwed complete all as specified and directed.

S&F 15mm bore CP stop valve/angle cock cast copper alloy with screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F 15mm bore fancy type chromium plated stop valve/angle cock (concealed type) with long shank and cup cast copper alloy with screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F vitreous china wash down Europian water closet pan (Padestal Pattern), including connection to flush pipe, 'P' or 'S' trap, with fixing bolts PVC seat cover with chromium plated mild steel hinges device and making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing including taking down the existing old one complete all as specified and directed.

S&F vitreous China squatting pan orissa pattern size 580mm x 440mm white with integral foot rest (including making good the disturbed portion as per surrounding areas excluding flushing cistern and flush pipe) including PVC (SWR) 'S'trap, provn of lime concrete and jointing to flush pipe (fixed in repair) all as specified.

S&F 10 litres capacity PVC valve less symphonic action type flushing cistern (ISI Marked) low level with inlet ball valve, float and handle including brackets & 32 mm size PVC flush pipe, complete all as specified and directed.

S&F vitreous china urinals, half stall type, complete including providing and fixing plugs, bedding urinal against wall in CM 1:2, securing urinal including water spider to plugs with and including 60mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush type, grating and union for discharge pipe complete all as specified and directed. (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)

S&F oval (of any colour as directed) counter wash basin of size 560x470x205mm including CP coupling and waste pipe complete all as specified and directed.

S&F PVC connection 15mm size, 450 mm long with PTMT nuts complete all as specified and directed.

S&F aluminium anodised tubular towel rail, 20mm dia, 60cm long, CP with a pair of brackets, fixed to wall with CP brass screw and PVC rawl plugs complete all as specified and directed.

S&F PVC coated mild steel conduit pipe 25mm dia (Drapery rod) with PVC coated MS clamps to hold drapary rod and decorative attachment at one or both ends of drapary rod, fixed to opening of door/windows, each opening n exc 1.50 mtr, contained with a pair of clamps and ap pair of side ornamental attachments complete all as specified & directed.

S&F 140mm long floor door stopper of aluminium alloy body and tongue,anodised, with hard drawn steel spring complete all as specified and directed.

Taking up or down 15mm bore steel water tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20mm bore steel water tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

S&F steel water tubing, 15 mm bore, galvanised , "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work in required etc, complete all as specified and directed.

S&F steel water tubing, 20 mm bore, galvanised , "medium grade" with all fittings and fixtures and short lengths, fixed to wall and ceiling or laid in floor including cutting chases for concealed work in required etc, complete all as specified and directed.

Cutting chase, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing,steps, cills, sunshades, shelves,lintels,etc and cutting chase for concealed water tubing or concealed conduit wiring etc and making good, cutting exc. 10cm but not exc 20cm girth complete all as specified and directed.

S&F GI spout pipe 40mm dia long medium grade incl making holes in walls & making good disturbed surfaces complete all as specified and directed.

Dismantling 75/100mm dia cast/PVC drain pipe, jointed in cement mortar fixed in trenches and taking out of trenches removing where directed complete all as specified and directedd.

S&F 75mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints fixed to walls/ laid in trenches or in floors, complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joints fixed to walls/ laid in trenches or in floors, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends complete all as specified and directed.

S&F 110mm bore PVC (SWR) branch piece (Single Y) equal or unequal complete all as specified and directed.

S&F 75mm bore PVC (SWR) multi floor trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 with grating complete all as specified and directed.

S&F 110mm dia PVC (SWR) vent cowl complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L RCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in cover slab, slabs supported on walls/baffle wall, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to rough finished surfaces of concrete for soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc. complete all as specified and directed.(inner girth only measured)

M&L PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in surface channel and drains complete all as specified and directed.

S&F CP jet spray hygenic spray set (health faucet) with 15mm bore 1m long tube acrylic type complete all as specified and directed.

Prepartion of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Prepartion of old wooden surfaces of any description exc 10 cm width or girth and applying two coats of synthetic enamel paint, complete all as specified and directed.

M&L brick work with sub class 'B' bricks in half brick thick walling built in CM 1:4 complete all as specified and directed.

S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including fixing fittings such as GI nipple for inlet, outlet, washout and overflow etc, including 25mm size ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe including dismantling old cemented/asbestos water/PVC storage tank complete all as specified and directed.

Taking down carefully existing aluminum / copper point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, ceiling fan with regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed.

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

Taking down unserviceable Sheet metal box & MCB DB SPN with MCB's of any make/capacity, complete, all as specified and directed by Engr-In-Charge.

Taking down unserviceable TPN DB with MCB's of any make/capacity, complete, all as specified and directed by Engr-In-Charge.

M&L, concealed point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed non metallic rigid PVC conduit medium grade( ISI marked with valid CML No) not less than 20 mm dia confirming to IS 14930 (Part-I) 2001, with all fitting and fixing accessories and 1.5 Sqmm FRLSH PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes factory made for mounting switch, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches. sockets etc complete for the following:- NOTE:- All point wiring considered for high buildings. Bidders must visit in work side before quoting the rates

One light point controlled by one switch.

One Ceiling fan point controlled by one switch.

One Exhaust fan/ wall mounted fan point controlled by one switch.

One 5 pin multipurpose socket out let 5/6 Amps on the same board with other switch.

One 3 pin/5 pin switch socket outlet, 5 Amps on independent board.

One Bell/Buzzer point controlled by one way 5 Amp push button switch.

Description all as per item No 105 here in before but point wiring with 2.5 sqmm FRLSH confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire.

S&F switch piano, PVC/Polycarbonate, flush button single pole one way 5 Amp complete all as specified and directed.

S&F socket out let, multipurpose, PVC/Polycarbonate, 2 in 1 5 pin, 5 Amp complete all as specified and directed.

S&F switch piano, PVC/Polycarbonate, flush button single pole one way 15 Amp complete all as specified and directed.

S&F bell push flush type, 5 Amps complete all as specified and directed.

S&F of buzzer Ding Dong, AC, 230 Volts, single pole complete all as specified and directed.

S&F socket out let multipurpose PVC/Polycarbonate, flush type, 2 in 1 6 Pin 5/15 amps complete all as specified and directed.

S&F electronic step rotary type fan regulator of two module capacity 80 to 100 Watt, 240 volts, AC 50Hz complete all as specified and directed.

S&F ceiling rose, PVC/Polycarbonate, surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

S&F Lamp holder with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings non ISI Marked complete all as specified and directed.

S&F LED Bulb 09/10 watt with provision of fixed in Lamp holder complete all as specified and directed.

S&F Decorative ultra slim LED Tubelight fitting of LED with extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt, 6500K fitting, incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor for electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed.

S & F security light fittings better optics for uniform distribution IP 65 protection LED of 30 watt, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mtr fixed to wall with 02 Nos FI clamps made of 40 x 5 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including reqd length of 1.5 Sqmm PVC multistranded BIS marked, 03 core copper conductor for connection from ceiling rose to light fittings incl testing on completion all as specified and directed.

Supply & fix BEE 5 star rating energy efficient ceiling fans 1200 mm sweep (BLDC) with minimum air delivery 210 cum/min, down rod all accessories required including regd length of 3 core 1.0 sqmm PVC multistranded copper conductor, PVC connector for proper hanging of fan and testing complete all as specified and directed.

Supply & fix Exhaust fans made of sturdy Engineering plastic complete with louvers shutter, 230 Volt, 50 Hz, RPM 1200, copper winding of sweep 300 mm, incl all fixing accessories required including making hole & regd length of 3 core 1.0 sqmm PVC multistranded copper conductor, and testing complete all as specified and directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia confirming to IS 14930 (Part-I) 2001, with all fitting & fixing accessories including one run single core PVC insulated unsheathed 6 Sqmm FRLSH copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. (NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

S&F sheet metal enclosure double door distribution board factory made for MCB DB load link VTPN 4 way suitable for MCCB as incomer, 100 Amp,4 pole & Including MCCB 100 amps 4 pole 16 KA complete. (when MCB's are to be used) with suitable size of busbar complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down all as directed by Engr-in-Charge at site.

S&F MCB DB, sheet metal enclosures double door SPN 8 way with bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F, MCB SPN 63 Amps, 240 volts 'C' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SP 240 volts, 6 to 40 Amps, 'C' series 10 KA including connection with suitable size copper lugs. complete all as specified and directed.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area 35 Sqmm 3.5 Core complete all as specified and directed.

Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete.

Bricks, old size sub class `B' laid in trenches with width wise along the alignment of the cable as protection complete.

S&F tube 'Light' grade galvanised Pipe of 50 mm dia with all fitting for cable protection, laid in trenches, fixed to wall and floor by MS shaddle & fixed with pole, 02 position by MS clamp made of 40x5 mm MS flat, complete all as specified and directed.

Excavation in trenches n exc. 1.5 m wide and n' exc. 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling of excavated soil, including spreading leveling, watering and well ramming in layers, not exceeding 25cm complete all as specified and directed.

Removing of surplus soil to a distance n exc 50 m and depositing where directed at a level n exc 1.5m above the starting point complete.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in 'D' shape 500 mm legth grouted in wall complete 01 x 6 mm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed.

M/S Bharmouri Construction (BID ID -3283134)

M/S ER CONSTRUCTIONS (BID ID -3283457)

somyaenterprises (BID ID -3276706)

VIVEKA ENTERPRISES (BID ID -3279676)