CO LIS for village Haleen and Balinda in GP Lambathach and Rod Tehsil Thunag Distt. Mandi (HP)

Amount

Excavation in foundation and trenches etc.in earth work in all kind of soil such as pick work, jumper work, saturated soil including bailing or pumping out water, blasting soft./hard rock, chiselling soft/.hard rock where blasting is prohibited in all lifts including trimming and dressing of sides, levelling of bed, stacking the excavated soil clear from the edge of excavation and then returning the excavated soil in 15cm. layers including consolidating each deposited layer by ramming , watering and then disposing of all surplus excavated soil as directed in all leads/lifts and shoring, strutting, timbering and dewatering where ever required as complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift.

Providing and laying cement concrete 1:6:12 ( 1cement:6 sand: 12 crushed stone aggregate 40 mm nominal size) and curing complete excluding the cost of form work in foundation and plinth complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and laying cement concrete 1:4:8 (1cement:4 sand:8 crushed stone agg.40mm nominal size) and curing complete excluding cost of form work in foundation and plinth complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift.

Providing and laying cement concrete 1:3:6 (1cement:3sand:6 crushed stone agg. 40mm nominal size)and curing complete excluding cost of form work in foundation and plinth complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and laying cement concrete 1:5:10 (1 cement:5 sand: 10 graded stone aggregate 40mm nominal size ) in plinth and foundation complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and laying cement concrete 1:1.5:3(1cement:1.5 sand:3 crushed stone agg.20mm nominal size ) & curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:-

In foundation and plinth complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Walls ( any thickness but not less than 0.1 m thickness) attached pillasters, buttresses, plinth and string courses, etc. from top of foundation level upto floor two level complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Suspended floors, roofs, landing and shelves and their support balconies, beams, girders, bressumers, and cantilivers upto floor two level complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift.

Providing & Laying No Fine concrete1:6 (1Cement : 6 Graded stone aggregate 40 mm nominal size) and curing complete :- in walls (any thickness but not less than 0.1 mtr thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level up to floor two level complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering ,strutting and propping etc. with wooden battens and ballies height of propping and centring below supporting floor to ceiling in all heights and removal of the same for insitu reinforced concrete and plain concrete workin:-

Vertical surfaces such as walls(any thickness) partions and the like including attached pillasters,buttresses plinth and string courses and the like complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Flat surfaces such as soffits of suspended floors,roofs,landings and the like floors etc.upto 200mm in thicknesscomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Foundation , footing bases of columns etc and mass concretecomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Beams, cantilivers, girders and lintels sides and soffits of beams,beam haunchings cantilivers, girders, bressumers and lintels not exceeding 1 metre in depth complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Edges of slab and breaks in floors and walls under 20 cm wide complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing tor steel reinforcement for RCC work including bending, binding and placing in position complete up to floor two levelcomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Cement concrete flooring 1:2:4(1 cement:2 sand:4 graded stone agg.20mm nominal size)laid in one layer finished with a floating coat of neat cement 40mm thickcomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Random rubble masonary / Polygonal rubble masonary (uncoursed or brought to courses) with hard stones of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1cement : 6sand :12 crushed stone aggregate 20mm nominal size) in Retaining / Breast walls in cement mortar 1:6 (1 cement : 6 sand) complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Brick work using common burnt clay building bricks in superstructure in cement mortar 1:6 (1cement : 6 sand ) in super structure in all leads and lifts. 2nd class bricks complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Half brick masonry in common butnt clay building bricks in cement mortar I :4 ( I cement 4 sand ) in super structure Ist. class bricks complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

6mm thick cement plaster to ceiling in cement mortar 1:3 (1cement:3 sand) complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

15mm thick cement plaster in single coat on rough side of brick/concrete/stone walls for interior plastering upto floor two level including arrises internal rounded angles chamfers and or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6 (1cement:6 sand) complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Sand filling under floors complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Stone/ Boulder filling under floors dry hand packed with complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Cement pointing on brick masonry with cement mortar 1:4 (1 cement :4sand) Raised and cutcomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Distempering with dry distemper of approved brand and manufacture (two coats)and of required shade on un-decorated wall surface to give an even shade over and including primer coat of whiting after thoroughly brushing the surface free from mortar droppings and other foreign matter including preparing the surface even and sand papered smooth complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil,grease ,dirt and other foreign matters,sand papering and knotting. Ready mixed primer paint brushing wood primer pinkcomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Painting two coats (excluding priming coat)on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of dirt,dust and other foreign matters sand papering and stopping with enamel paint other than whitecomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Industrial tiles 10mm thick of size 600X600mm in flooring cement mortar 1:4 (1cement:4 sand) finished with flush pointing in white cement complete in all respects of reputed make Somani ,Nitco, Johanson, Kajaria etc.as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

White glazed tiles 6 mm thick in skirting risers of steps and dado 12mm thick cement mortar 1:3 (1cement:3 sand) and jointed with cement slurry complete of reputed make Kajaria, Somani, Johanson etc. in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. ..

Providing and fixingf MS grill of required patter in wodden frames of wndos etc with MS flats, squares or rounded bars with round headed bolts and nuts or by screw.complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing wood work in frames of doors, windows, clerestory windows and other frames wrought, framed and fixed in position. (2nd class deodar wood)complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and Fixing panneled glazed or panelled and glazed shutters for doors, windows and clerestory windows,including black enamelled iron butt hinges with necessary screws. 40 mm thick. (2nd class deodar wood)complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing 40x3 mm iron hold fast 40 cm long including fixing to frame with 10 cm da bolts nuts and wooden pluges and embencing in C.C. block 30x10x15 cm 1:3:6 ( 1 cement:3 sand: 6 graded stone aggregate 20 mm nominal size) complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing anodized aluminium sliding door bolts with bolts and nuts screws etc.complete. complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing anodized aluminium tower bolts(barrel type)with screws etc.complete complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing anodized aluminium handles with necessary screws etc.completecomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing plinth protection 50mm thick in cement concrete 1:3:6(1cement:3 sand:6 crushed stone agg.20mm nominal size)complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and Fixing C.I. Sluice valve (with hand wheel) as per IS: 780 Class-I up to 300 mm dia (includingbrass spindle and as per IS: 2906 class II for diameters more than 300 mm complete with bolts, nuts , rubber insertion etc. (The tail pieces if rewuired shall be measured and paid for separately) for Out lets pipe & Scour pipes dia complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

150 mm dia for In Let , Out Let and Scour complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Fixing of GI pipe 150 mm dia for inlet,outlet and scour pipecomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift.

Providing and Laying Cement concrete lining 0.075 cm thick for irrigation channel using cement concrete 1:3:6 ( 1 cement:3 sand 6 aggregate 20mm nominal size) hand mixed concrete lining in bed complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

In bed

In slope

Providing and Fixing precast concrete man hole cover and frame, conforming to IS-12593-part-1-1888 and IS 12592-part-II-1991, 500 mm diameters heavy duty complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing Cast iron/sand cast iron spun spigot ventilating pipe 100mm dia, 1 mtr high with Cast iron Cowl fixed at top complete in all respects as per the direction and to the entire satisfection of the Engineer-in-chargecomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing automatic flushing cistern with a pair of CI or MS.bracket complete with fitting including CI Syphonic appratus mosquitos proof lid,CP brass unions and coupling for connecting with inlet, outlet and over flow pipes including cutting holes and making good the same over flow pipes to be measured and paid for separately (Viterous china 5 litres capacity)complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing vitreous china wash down water closet( Indian Type,W.,C.pan)with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1 (1cement:1 sand) (Seat and cover to be measured and paid for separately) (white colour) in all leads and lifts.complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing 100mm size P or S trap for water closet(Squatting pan) including jointing the trap with the pan and soil pipe in cement mortar 1:1(1cement:1 sand) Sand Cast iron in all leads and liftscomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing viterious china wash basin with single hole for pillar tap with CI or MS bracket painted white including cutting hole including good the same excluding fitting Cera sanitary work (Cormet) white 550x400 white complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing viterious china padestral for wash basin complete recessed at the basis for reception of pipe and fittings Cera sanitary work(Carnet) white(Viterious china in white colour)complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing of water storage tank sintex having of capacity 500 litres with necessary fittings including over flow pipes,scour pipes etc.inlet and outlet and inside paint of required shade for inlet or outlet and inside paint of approved quality complete including hoisting complete in all respects.complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing on wall face PVC (D - Plast) rain water pipes of working pressure not less 4.5 Kg/Sqcm including fitting the joints with approved adhesive complete with in all leads , lifts and carriage of materials.110 mm nominal borecomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing on wall faces PVC door bend (D-Plast) with oval access door, insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive complete.75 mm nominal bore complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing to wall ceiling and floor galvanised mild steel tubes(Medium grade) tube fittings and clamp including making good the wall ceiling and floor in all leads and lifts) 15mm nominal bore complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing full way wheel valve 15 mm dia gun metalcomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and fixing brass bib tap(Superior quality or heavy type)15 mm diacomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing & Fixing CP Brass Soap Dish with CP brackets fixed to wooden plugs with CP brass screws complete in all respectcomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Wiring for light point/fan point/exhaust fan/call bell point with 1.5 sqmm.PVC insulated heat resistant flame retardant(HRFR)and low smoke single core(Flexible)copper condutor cable in surface /recessed PVC conduit and earthing the light point with 1.5 Sqmm.HRFRLS /PVC insulated single core copper conductor cables as required in all leads and lifts.group -C complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Wiring for circuit /Sub-main with following size PVC insulated heat resistant flame retardant(HRFR) and low smoke single core (Flexible) copper conductor cable in surface/recessed steel conduit along with 1 NO.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

2x6 Sqmm.

2x4 Sqmm.

Supplying and fixing 3 pin 5/6 amps.socket outlet on the exists switch box/covers including connections etc.as required complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Supplying and fixing 2 way 5/6 amps.Tumbler/Piano type switch on the existing switch box on the switch box/cover including connections etc.as requiredcomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Supplying and fixing 3 pin 15/16 amps.socket outlet on the exists switch box/covers including connections etc.as requiredcomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Supplying and fixing 15/16 amps.Tumbler/Piano type switch on the existing switch box on the switch box/cover including connections etc.as required complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Supplying and fixing wooden box of following size(nominal) on surface or recess with suitable size of phenolic laminated sheet cover of in front as requiredcomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

200Xmmx150mmx75mm deep.

180Xmmx160mmx60mm deep.

Providing and Supplying CFL 1 x 23 watt of reputed make complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Providing and Supplying of CFL 1 x 5 watt of reputed makecomplete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

Supplying and fixing 5 amps.to 32 amps.rating 240 volts L-series miniature circuit breaker of following poles in the existing MCBDB complete with connections, testing and commissioning etc.as required category-A (Single pole) complete in all respects as per the direction and to the entire satisfection of the Engineer-in-charge in all lead and lift. .

(Centrifugal Pump Set) Phase Ist. Haleen Supply of Horizontal spindle,horizontal/redial split casing/and suction(Back-pullout arrangements single/double/multi stage centrifugal pumps or combination of pumps. In series/parallel of KSB/ Mathur & Platt/Jyoti/ Kiloskar/ BE / Maxflow/Beaconweir Sabar/Graund fos make conforming to BIS 5659-1970) pump(latest with upto date ammendments, read with BIS 9137-1978 (latest edition)suitable for lifting water of under mentioned characterstics with bronze/ Suitable alloy, priming funnels.casing ring and shaft motor of bronze.shaft of steel grade ASA-410 or as per manufacturer standard with cast iron casing coupled directly through a flexible coupling on a common MS/ Cast Steel plate (base plate from the principle manufactor of pumping set)to coupling sliperring TEFC of electic induction motor/ motor of standard make such as Kiloskar/ NGEF/ Cromption/ Siemen/ Jyoti/ BHEL/ GEC/ ABB conforming to BIS 325-1978) read as BIS 900-1972 and IS: 12615:2011 with IE-2 specifications (latest up to date ammendements) it should include the cost of bearings, nuts & bolts painting etc. and shall be and suitable for operation on the data given as below:-

Discharge(Q)9.43 lps for each pump

Total Dynamic heads:- 509.54 Meter

LWL in sump well (h) :-1880.5 Meter

Shaft level :- 1880 Meter

Level at discharge point :-2353 Meter

Suction lift +ve

Discharge head :-473 Meter

Static head :- 473 Meter

Rising main

a) Length :-2290 Meter

b) Dia :-150mm

Pumping hours :-20.00 hrs

Altitude of installation above MSL:-1735 Meter

Characterstics of water clear water with turbidity up to 600 ppm

Supply,insallation Testing and Commissioning of soft Starter panel for centrifugal pump made out of 16 gauge sheet powder coated dust and vermin proof wall/base mounted and front opeing door type with copper insulated wiring suitable to operate 2 Nos. pumps (2 working) each of the suitable rating through Soft starter machanism.Starter should be capable enough to handle the following faults like short circuit, over current, under current, over voltage, under voltage dry run protection and phase loss with LED ON/off &TRIP indicators.Power quality monitoring and controling Relay at the incomer feeder, should be fitted with surge suppressor device suitable to protect against class 1&2 surges of reputed make i/e JSV approved complete in all respect as per direction of Engineer-in-Charge. Make: JSV approved.Complete soft starter panel shall be made two years warranty period, during warranty period any fault noticed shall be rectified by the contractor at his own cost, if necessary starter shall be replaced.

Soft Starter and Mains Power Contactors of required ratings as per type-2 co-ordination for offered pumping machinery JSV approved complete in all respect. Make:- JSV Approved.

Voltage protection device to protect panel from over voltage and under voltage Make:- JSV Approved.

Single phasing and phase reversal protection device to safeguard system from single phasing and phase reversal of the supply voltage.

Multi function meter indicating different parameters like current voltage KWH,PF,THD etc.With RS 485 communication Make:- JSV Approved.

Main incomer MCCB of suitable capacity of L & T / Schnieder/ABB make on the coming feeder for pumping set confirming to BIS 2516-1985 (Latest edition).

Individual starter incomer MCCB/MCB of suitable capacity of L&T/ schnieder/ABB make on the feeder for pumping set confirming to BIS 2516-1985(latest eaition)

LED three phase indicating lamps complete with toggel switches for individual motors confirming to BIS 3452 (part ammendments)

LED ON/OFF& TRIP indicator and push buttons, control and power wiring, power capacitor, cooling fan 230 VAC , contorl terminal, Bus Bar, i.e Bolt insulator etc.

Surge supressor device with lsolating MCCB to eliminate the power surges due to lightening and system surges.

Control Transformer to provide a stable control volatge to safegaurd the control circuit of all the components from the voltage surges and spikes.

Independent control panel with switch fuse unit and fuses of suitable amperage to eliminate the kitkat fuses of HPSEB make: Siemens / Schnieder/ L & T.

Providing double flanged Cl sluice valve PN-1 of leader/kirlosker/Kartar make and equal to dia of suction pipe and capable of withstanding the normal seat perssure as per IS:780:1984 with up to date amnmendments.

Providing double flanged cast steel sluice valve, ASA 300 of KSB/leader/kirlosker make and one step higher then delivery line of pump and capable of withstanding normal seat pressure as per BIS standard with up to date amnmendments.)

Providing double flanged swing type cast steel reflux valves ASA-300 of KSB/leader/kirlosker make and having bye pass arrangements of one step higher then delivery of pump and capable of withstanding normal seat pressure as per BIS standards with upto date amnmendments.

Providing double flanged cast steel reflux valves class ASA-300 of KSB/leader/kirlosker make for rising main and capable of withstanding normal seat pressure as per BIS standards with upto date amnmendments. (150 mm dia)

Providing 100 mm dia circular dial analog pressure gauge of suitable range of fiebig/bourden/PREGA/precision make complete with all accessories such as stop cock, copper tubing etc.as per IS:3624-1987 with upto date amnmendments.

Providing discharge meter of standard make to be fixed on the rising main in pump house as per the directions of the Engineer- in- Charge as per IS:2373:1981 with upto date amnmendments.(150 mm dia)

Installation of all the items apparing as per the schematic draqwing.

Providing and Fixing double flanged MS/GI piping work (Layout to be approved by the Engineer-in-Charge) for suction and delivery pipes suitable to pump (s) offered and common header as per the R/Main respectively complete with all specials such as bends, tees, reducers. increasers with companions flanges matching with the relevant specifications of the accessories including rubber/ asbestos gasket of minimum 3 mm thickness as per IS: 2712:1979 and required number of nuts and bolts as per IS: 1364: 1983. The pipes fittings and joints shall be as per relevant IS code & to withstand 1.5 times total head stipulated under item No. 60 above. The size of the various components to be as under:

Suction pipe: One dia higher then the suction of pump offered and suitable to keep the velocity of flow from 1 to 1.5 M/second in the suction pipe.

Delivery pipe: One dia higher then the delivery of the pump offered and suitable to keep the velocity of flow from 1.5 to 2 M/ second in the delivery pipe.

Common Header: One dia higher then delivery of pump will extend upto 5 meters from the outer wall of the pump house in the direction to be jointed.

Providing and Laying copper PVC insulated arsoured power cable (One cable carrying all the three phases) of suitable size and capacity to motors and all other electrical equipments as per IS: 1554 (P-I) 1988 or latest with upto date ammendements of siemens/ GLOSTER/ IEC/ICC/EICO/NATIONAL/GRANDLAY make including all other accessories such as thimbles, flexible pipes, solders, nuts and bolts cable glands etc. laid in pipes or trenches under floor.

Motor side 3 core (From switch to starter and starter to motor)

Supply side 3.5 core (From Meter of HPSEB to bus bar and switch)

Providing and Fixing double loop earthing with GI plate 600X600X3mm thick electrode complete with material such thimbles nuts and charcoal and common salt, 25mmX5mm copper strips as per IS: 3043:1987 with upto date ammendments for motors and other electrical equipments and digging of pits etc. complete in all respect.

Phase:- Ist. Balinda Supply of Horizontal spindle,horizontal/redial split casing/and suction(Back-pullout arrangements single/double/multi stage centrifugal pumps or combination of pumps. In series/parallel of KSB/ Mathur & Platt/Jyoti/ Kiloskar/ BE / Maxflow/Beaconweir Sabar/ Graund fos make conforming to BIS 5659-1970) pump(latest with upto date ammendments, read with BIS 9137-1978 (latest edition)suitable for lifting water of under mentioned characterstics with bronze/ Suitable alloy, priming funnels.casing ring and shift motor of bronze.shaft of steel grade ASA-410 or as per manufacturer standard with the cast iron casing coupled directly through a flexible coupling on a common MS/ Cast Steel plate (base plate from the principle manufacturer of pumping set) to coupling Totally emclosed fan cooled electric induction motor/ motor of standard make each such as Kiloskar/ NGEF/ Cromption/ Siemen/ Jyoti/ BHEL/ GEC/ ABB & suitable for operation on 415 (+/-) 10% volts 50 cycle per second 3 phase AC electric supply conforming to BIS 900-1972 and IS 12615-2011 with IE -2 specification 2900 RPM (latest upto date ammendments) it should include the cost of bearing nuts & bolts,painting etc. and shall be and suitable for operation on the data given as below

Discharge(Q)10.18 lps

Total Dynamic heads:- 266.53m

LWL in sump well (h) :-1880.5m

Shaft level :- 1880m

Level at discharge point :-2135m

Suction lift +ve

Discharge head :-255m

Static head :- 255m

Rising main

Length :-750 rmt

Dia :-125mm

Pumping hours :-20 hrs

Altitude of installation above MSL:-1735

Characterstics of water clear water with turbidity up to 600 ppm

Temperature 20 degree centigrade

Supply,insallation Testing and Commissioning of Soft Starter panel for centrifugal pump made out of 16 gauge sheet powder coated dust and vermin proof wall/base mounted and front opeing door type with copper insulated wiring suitable to operate 1 no pumps working each of the rating 75 HP through star delta starter machanism.Starter should be capable enough to handle the followinh faults like short citcuit over current under current over voltage under voltaga dry run protection and phase loss with LED ON/off &TRIP indicators complete in all respect of reputed make JSV approved.Complete soft starter panel shall be made two years warranty period and fault noticed shall be rectified by the contractor at his own cost, if necessary starter will be replaced.

Providing & Fixing Star Delta starter and mains power contactors of required ratings as per type-2 cordination for offered pumping machinery.

Voltage protection device to protect panel from over voltage and voltage

Single phasing and phase reversal protection device to safeguard system from single phasing and phase reversal of the supply voltage.

Multi function meter indicating different parameters like current voltage KWHPF.THD etc.With RS485 communication makr JSV approved/the product should be of global brand

Main incomer MCCB/MCB of suitable capacity of l&T Schnieder/ABB MAKE ON THE FEEDER FOR PUMPING SET CONFIRMING TO BIS 2516-1985(LATEST EDITION).

Individual starter incomer MCCB/MCB of suitable capacity of L&T/ schnieder/ABB make on the feeder of pumping set confirming to BIS2516-1985(latest eaition)

Three phase indicating lamps complete with toggled switches for individual motors conforming to BIS 3452(PART 1&II) LATEST WITH UPTO DATE AMMENDMENTS.

LED ON/OFF& TRIP indicator and push buttons control and power wiring power capacitor cooling fan 230VAC control terminal bus bar i.e bolt insulator etc.

Surge supressor device with lsolating MCCB to eliminate the power surges due to lightening and system surges.

Control transformer to provide a stable control volatge to safegaurd the control circuit of all the components from the voltage surges and spikes.

Independent control panel with switch fuses unit and fuses of suitable amperage to eliminate the kitkat fuses of HPSEB make SV approved/the product should be of global brand

Providing double flanged Cl sluice valve PN-1 of leader/kirlosker/Kartar make and equal to the dia of suction pipe and capable of with standing normal seat perssure AS PER IS:780:1984 with up to date amnmendments.

Providing double flanged cast steel sluice valve ASA 300 of KSB/leader/kirlosker make and one step higher then the delivery line of pump and capable of various standing normal seat pressure as per standard with up to date amnmendments.

Providing double flanged cast steel reflux valves class ASA-300 of KSB/ leader/kirlosker make for one step higher then delivery of pump and capable of withstanding normal seat pressure as per BIS standards with upto date amnmendments.

Providing double flanged cast steel reflux valves class ASA-300 of KSB/leader/kirlosker make for rising main and capable of with standing normal seat pressure as per BIS standards with upto date amnmendments.(125 mm dia)

Providing 100 mm dia circular dial analog pressure gauge of suitable range of fiebig/bourden/PREGA/precision make complete with all accessories such as stop cock copper tubing etc.as per IS:3624-1987 with upto date amnmendments.

Providing discharge meter of standard make to be fixed on the rising main in pump house as per the directions of the engineer in charge as per IS:2373:1981with upto date amnmendments.(125 mm dia)

Installation of all the items apparing as per the schematic drawing.

Providing and laying copper insulated armoured power cable(one cable carrying all the three phases) of suitable size and capacity to motors and all other electircal equipments as per IS:1554(P-I)1988 or latest with upto date ammendments of siemens/GLOSTER/ICE/ICC/EICO/NATIONAL/GRANDLAY make including all othres accessories such as thimbles, flexible pipes solders , nuts and bolts cable Glands etc. laid in pipes trenches under floor.

Motor side(From switch to starter and starter to motor)3core cable

Supply side(From meter of HPSEB to bus bar and switch)3.5 core cable

Providing and fixing double loop earthing with GI plate 600 mmx600x3mm thick electrode complete with material such thimbles nuts and charcoal and common salt 25mmx5mm copper strips as per IS:3043:1987 with up to date ammendments for motors and other electrical equipments and digging of pits etc,complete in all respect.

Providing and Fixing double flanged MS/GI piping work (Layout to be approved by the Engineer-in-Charge) for suction and delivery pipes suitable to pump (s) offered and common header as per the R/Main respectively complete with all specials such as bends, tees, reducers. increasers with companions flanges matching with the relevant specifications of the accessories including rubber/ asbestos gasket of minimum 3 mm thickness as per IS: 2712:1979 and required number of nuts and bolts as per IS: 1364: 1983. The pipes fittings and joints shall be as per relevant IS code & to withstand 1.5 times total head stipulated under item No. 83 above. The size of the various components to be as under:

Suction pipe: One dia higher then the suction of pump offered and suitable to keep the velocity of flow from 1 to 1.5 M/second in the suction pipe.

Delivery pipe: One dia higher then the delivery of the pump offered and suitable to keep the velocity of flow from 1.5 to 2 M/ second in the delivery pipe.

Common Header: One dia higher then delivery of pump will extend upto 5 meters from the outer wall of the pump house in the direction to be jointed.

Providing , laying, fixing, jointing and testing in trenches MSERWE pipe of following dia meters confirming to MSERW pipe (ISO-3183),Steel Grade-A and having wall thickness as specified below with plain end and capable of withstanding required test pressure in random length of 4 to 7 meters, including specials, short pieces, bends, reducers, tees etc. made from parent tube, providing and welding of MS flanges detailed as below. The MS flanges shall confirm to BIS 6392-1971 (with latest up to date amendments) duly welded in two layers (two inner and two outer) with pipes at both ends as per relevant BIS standards along with nuts and bolts of required sizes, 3mm thick compressed asbestos fiber/synthetic rubber gaskets confirming to relevant BIS standards. The laying of pipe will include all operation such as cutting, welding, jointing, providing & fixing of MS flanges, fabrication of bends, tees etc. including lowering and laying in excavated trenches to ensure required level including flushing, cleaning and hydraulic testing complete in all respects to the satisfaction of the Engineer in charge. The fabricated bends shall have three or four cuts having its radius not less than five times the dia of pipe. The pipes shall be factory galvanized (zinc coating both inside and outside) as per relevant IS standards. The welding electrodes shall be as per IS 814 of Advani Oerlikon/ L&T or ISI marked make. The rates also includes entire carriage of material, flushing, cleaning & hydraulic testing complete to the best satisfaction & directin of Engineer in charge with in all leads and lifts. (Earth work in trenches will be measured and paid for separately).

150 mm dia MESRW pipe 5.20 mm thick FT-34

150 mm dia MSERW pipe 5.20 mm thick (butt welding)

Laying, fixing, jointing and testing in trenches GMS pipe of following dia meters confirming to confirming to BIS :1239 (Part-1), of following grade and having wall thickness as specified below with plain end and capable of withstanding required test pressure in random length of 4 to 7 meters, including specials, short pieces, bends, reducers, tees etc. made from parent tube, providing and welding of MS flanges detailed as below. The MS flanges shall confirm to BIS 6392-1971 (with latest up to date amendments) duly welded in two layers (two inner and two outer) with pipes at both ends as per relevant BIS standards along with nuts and bolts of required sizes, 3mm thick compressed asbestos fiber/synthetic rubber gaskets confirming to relevant BIS standards. The laying of pipe will include all operation such as cutting, welding, jointing, providing & fixing of MS flanges, fabrication of bends, tees etc. including lowering and laying in excavated trenches to ensure required level including flushing, cleaning and hydraulic testing complete in all respects to the satisfaction of the Engineer in charge. The fabricated bends shall have three or four cuts having its radius not less than five times the dia of pipe. The pipes shall be factory galvanized (zinc coating both inside and outside) as per relevant IS standards. The welding electrodes shall be as per IS 814 of Advani Oerlikon/ L&T or ISI marked make. The rates also includes entire carriage of material, flushing, cleaning & hydraulic testing complete to the best satisfaction & directin of Engineer in charge with in all leads and lifts. (Earth work in trenches will be measured and paid for separately).

150 mm dia GI pipe 5.40 mm thick FT -28 (Heavy)

150 mm dia GI pipe 4.80 mm thick FT -17 ( Medium)

125 mm dia GI pipe 4.80 mm thick FT-28 (Medium)

Laying,jointing and testing( by way of circumfrential butt welded joints by electrical arc welding ) and testing of GMS pipe of following dia meters confirming to BIS 1239 (Part-1), grade specified below (latest with upto date amendments) having wall thickness as specified below with bevelled ends and capable of withstanding required test pressure in a random length of 4 to 7 meters, including manufacturing reducers/ tapers , all short pieces, beds etc. as per site requirement made from parent tubes . The laying of pipe will include all operation such as cutting, welding, jointing, fabrication of bends, tees etc. including lowering and laying in excavated trenches to ensure required level including flushing, cleaning and hydraulic testing complete in all respects to the satisfaction of the Engineer in charge. The fabricated bends shall have three or four cuts having its radius not less than five times the dia of pipe. The pipes shall be factory galvanized (zinc coating both inside and outside) as per relevant IS standards. The welding electrodes shall be as per IS 814 of Advani Oerlikon/ L&T or ISI marked make. The rates also includes entire carriage of material, flushing, cleaning & hydraulic testing complete to the best satisfaction & direction of Engineer in charge with in all leads and lifts. (Earth work in trenches will be measured and paid for separately).

150 mm dia GI pipe 5.40 mm thick (Heavy)

150 mm dia GI pipe 4.80 mm thick (Medium )

125 mm GI pipe 4.80 thick (Medium)

Pankaj Thakur contractor

KUSHAL SINGH RAGHAV

Royal Construction Company