construction of J.E Section office building including Septic Tank along with soak pit W.S and S.I and E.I. wiring at Swarghat under Electrical Sub Division HPSEB Ltd Kot (H.P) (NIT-25/2020-21)

Amount

Construction of Retaining wall

Excavation in foundation,trenches etc.in earth work, lift upto 1.50 metres stacking the excavated soil not more than 3 meters clear from the edge of the excavation and then returning the stacked soil in 15 cm.layers, when required in to plinth sides of foundations etc. and then disposing of all surplus excavated earth as directed with in a lead of 20 mtrs. (PW/JW ). 50% each

Providing and laying cement concrete 1:5:10 (1 cement : 5 Sand :10 graded stone aggregate 40mm nominal size) and curing complete excluding the cost of form work in: Foundation and plinth

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give fair finish i/c centring,shuttering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs etc.In

(i) vertical surface such as walls (any thickness) partitions and the like.

Providing and laying cement concrete 1:4:8 (1 cement : 4 sand : 8 Graded stone aggregate 25mm nominal size) and curing complete excluding cost of form work in foundation and plinth in breast and retaining walls etc.

Providing and fixing PVC (D-Plast) rain water pipes- 75mm dia.pipe

Stone filling behind the Retaining walls

Construction of J.E Section office building

Excavation in foundations, trenches etc., in earth work, lift upto 1.50 Metres stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 20 metres.(PW50%,JW50%)

Providing & laying cement concrete 1:3:6 (1 cement:3 Sand: 6 graded Stone aggregate 40mm nominal size) & curing complete excluding cost of form work in Foundation & Plinth.

Random rubble masonry/polygonal rubble masonry (Uncoursed/brought to courses) with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 Sand : 12 Graded stone aggregate 20mm nominal size) in cement mortar 1:6 (1cement:6 sand)

Providing form work with steel plates 3.15mm.thick welded with angle iron in frame 30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc. with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs. and removal of the same for insitu-reinforced concrete & plain concrete work in:Foundation, footings basis of columns etc. and mass concrete.

Columns, pillars, posts and struts

Beams, cantilever, girders and lintels.

Flat surfaces such as soffits of suspended floors, roofs, landings and the like.-Floors etc.upto 200mm. In thickness.

Providing and laying cement concrete 1:1.5:3 (1 cement :1.5: Sand : 3 graded stone aggregate 20 mm nominal size and curing complete excluding cost of form work in Foundation and plinth

Foundation, footings basis of columns etc. and mass concrete.

Suspended Floor roofs, landing and shelves and their support balconies,beams,girders,bressumers and contilever upto floor two level

Providing mild steel/Tor steel reinforcement for R.C.C. work including bending, binding and placing in position complete upto floor two level :

Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:5 (1 Cement : 5 Sand) Second Class Bricks

Providing woodwork in frames of doors,windows, clerestory, windows and other frames wrought,framed and fixed in position. Sal wood.

Providing and fixing panelled glazed or panelled and glazed shutters for doors windows and clerestory windows. Including black enamelled iron butt hinges with necessary screws.40mm thick, 2nd class deodar wood.

Providing and fixing wire gauge shutters using galvanised M.S. wire gauge of I.S. gauge designation 85 G. with wire of dia 0.56 mm for doors windows and clerestorey windows including bright finished black enamelled iron hinges with necessary screws. 2nd class deodar wood.

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm diameter bolts & nuts and wooden plugs and embeding in cement concrete block 30x10x15cm. 1:3:6 ( 1 cement : 3 sand: 6 graded stone aggregate 20mm nominal size)

Boulder filling dry hand packed tightly in wire crates vertical bunds with sloping face (wire crates to be measured separately)

Providing and fixing M.S. grills of required patterns in wooden frames of windows etc. with M.S. Flats, square or round bars with round headed bolts and nuts or by screws.-Plain grill.

Applying priming coat over new steel & other metal surfaces after& including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete.With ready mixed priming paint brushing red lead,Red-oxide/ zincoxide chrome.

20mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:5 (1Cement:5 Sand).

6mm thick plaster to ceiling with cement mortar1:3(1 cement:3 Sand)

Providing and laying Duro stone vetrified tiles(600x600mm) in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete.

White glazed tiles 6 mm thick in skirting risers of steps and dado 12 mm thick cement mortar 1:3 (1 cement :3 sand) and jointed with cement slurry.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete.

Applying priming coat on new concrete/masonry/asbestos cement/plastered surfaces after and including preparing the surface by thoroughly cleaning oil,grease,dirt and other foreign matter and sand papering as required with :Readymixed primer

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth complete.

Applying priming coat over new wood and wood based surfaces after and including prepering the surface by thoroughly cleaning oil,grease,dirt and other foreign matter) sand papering and knotting.- Readymixed paint brushing wood primer pink

Painting two coats (excluding priming coat)on new wood and wood based surfaces,with readymixed paint,brushing to give an even shade including cleaning of all dirt,dust and other foreign matter sand papering and stopping:- Readymixed paint other then white

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick/stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size)

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall. 15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1 Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design.

Steel work welded in built up sections,trusses and framed work,including cutting ,hoisting,fixing in position and applying a priming coat of red lead paint In trusses and trussed purlins in buildings

Painting two costs (excluding priming cost on new steel and other metal surfaces eith enamel paint brushing to give an even shade including cleaning the surface of all dirt,dust and other foregin matters-Enamel paint other than white

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etc. complete.250x16mm

Providing and fixing aluminium tower bolts (berrel type) anodized trans parent or dyed to required shade and colour with screws etc. complete.(150x10mm)

Providing and fixing aluminium handles anodized transparent or dyed to required colour & shade with necessary screws etc. complete.125 mm

Providing and fixing M.S hooks and eyes.200mm

Providing and fixing M.S pressed butt hinges bright finished with necessar screws etc complete(100x58x1.90mm)

Providing and fixing SS25 diameter curtain rod with bracket,plugs etc wherever required.

Providing and fixing door closer hydraulic type

Construction of Septic Tank along with soak pit, W.S and S.I

Excavation in foundations, trenches etc., in earth work, lift upto 1.50 Metres stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15cm. layers, when required in to plinths sides of foundations etc., consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with in a lead of 20 metres.(PW50%,JW50%)

Providing and laying cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm nominal size) excluding cost of centring and shuttering in:Foundations and plinth:

Brick work using common burnt clay building bricks in foundation and plinth in Cement Mortar 1:5 (1 Cement : 5 Sand) Second Class Bricks

Providing form work of ordinary timber plankings so as to give a rough finish including centring,shuttering, strutting and propping etc. height of propping and centring below supporting floor to ceililng not exceeding 4 metres and removal of the same for insitu reinforced concrete and plain concrete work in:-Floors etc. upto 200mm in thickness:

15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth. Cement Mortar 1:5 (1Cement:5 Sand).

Providing and laying cement concrete 1:1.5:3 (1 cement :1.5: Sand : 3 graded stone aggregate 20 mm nominal size and curing complete excluding cost of form work in Suspended Floor roofs, landing and shelves and their support balconies,beams,girders,bressumers and contilever upto floor two level

Providing Tor Steel/mild steel reinforcement for RCC work including bending binding and placing in position complete upto floor two level- Tor Steel.

Suppliying cast iron cover without frame for manholes:For frame of internal dimension 455mmx610mm rectangular C.I. cover (light duty single seal pattern-1) the weight of cover to be not less than 23kg.

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete.:-110mm nominal size

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete.-110 mm dia.

Providing and fixing C.I Cowl

Boulder filling dry hand packed tightly in wire crates vertical bunds with sloping face (wire crates to be measured separately)

Constructing manhole with R.C.C. top slab in 1:@:4 mix in 1 cement:2sand:4 graded stone aggregate 20mm nominal size) foundation concrete1:4:8(1cement:4sand:8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3(1cement 3sand) finished with a floating coat of neat cement & making channels in concrete 1:2:4 mix(1cement:2sand:4graded stone aggregate 20mm nominal size) finished smooth complete i/c curing & testing:

Inside size 800mm x 800mm and 500mm deep including C.I cover with frame. (Light duty single seal pattern - 1) 455 mmx610mm internal dimensions total weight of cover and frame to be not less than 38kg . (weight of cover 23 kg and weight of frane 15 kg.)-With 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand).

Providing and fixing vitreous China wash down,water closet (European type. W.C. pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1(1 cement : 1 sand) (Seat and over to be measured and paid for separately):-Ordinary closet

Providing and fixing vitreous China wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings:-Circular 460mm dia (countertop)

Providing and fixing vitreous China padedstal for wash basin complete recessed at the back for the reception of pipes and fittings .

Providing and fixing C.P Brass bib tap with Capstan head-15mm dia

Providing and fixing C.P Brass pillar tap with Capstan head-15mm dia

Providing and fixing c.p. brass angle valve 15mm without Nuts and pipe.

Providing and fixing PTMT Coloured / white automatic flushing cistern with a pair of PVC / C.I. or M.S. bracket complete with fittings including PVC syphonic apparatus, mosquito proof lid, PVC union and coupling .-5 litres net capacity.

Providing and fixing C.P. connection pipe with brass unions :- 45cm length-15mm nominal bore

Providing and fixing PVC water storage tank of ISI : 12701 marked,G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hoisting upto all heights above ground level :-1000 litres net capacity tank

Providing and fixing cast iron floor trap of self cleaning desion with sand cast iron screwed down or hinged grating with out vent arn complete including cost of cutting and making goods the walls and floors :- 100mm nominal diameter

Providing and fixing PVC 'P' or 'S' trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. -110mm

Providing and fixing to wall ceiling and floor galvanised mild steel tubes (Medium grade) tube fitting and clamps including making good the wall, ceiling and floor:-15mm nominal bore

Providing and fixing brass full way valve with wheel:-15mm nominal bor

Providing and fixing 600mm x 450 mm bevelled edge miror of superior glass mounted on 6mm thick A.C. Sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers.

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws :-

Providing and fixing plastic seat (Solid / Hollow type) and cover for wash down water closet with C.P. Brass hinges and rubber buffers :

Providing and fixing PTMT jet spray of approved quality and colour with one metre tube.

E.I. wiring

Wiring for light point / fan point / exhaust fan /call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required.

Group C.

Supplying and fixing following rating Piano-type switch /socket on the existing switch box / cover including connections etc. as required.

S.P. 5/ 6 Amps one way switch, piano type.

Bell push, piano type.

5 pin 5/ 6 Amps socket outlet, porcelain base/ piano type.

Supplying and fixing metal box of 180mmx100mmx60mm deep (nominal size) on surface/recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 6 pin 15/16 amps socket outlet and 15/16 amps, piano type switch, connections, painting etc. as required.

Supplying & fixing electrical switch board having 3 nos of 5 amp switches and socket om suitable size of metal box of 200x150x75 mm deep(nominalize) on surface or in recess with suitable size of phenolic laminated sheet cover in the front i/c providing & fixing 3 nos 5 pin 5/6 amp piano type switch.connection painting etc as reqd(for light plugs)

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required.

2x1.5 Sq. mm.

2x4.0 Sq. mm.

2x10.0 Sq. mm.

Supplying and fixing bakelite batten/angle holder including connections etc. as required:-

Supplying and fixing ceiling rose on the existing junction box / wooden block including connections etc. as required.

Providing and fixing TP&N switch disconnector fuse unit cubical type, 415/500 volts with 3 No. HBC/HRC fuses, in sheet steel enclosure including drilling holes on the board, connections, earthing the body etc. as required.

100 Amp. Category-A

Supplying and fixing sheet metal bus-bar chamber suitable for 100 Amp. 415 volts capacity with 4 No. copper strip bus-bars each of length 600mm & cross-sectional area (25.4mmx3.17mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (680mmx400mmx150mm) nominal with all accessories including connections, earthing the body etc. as required:-

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required:-

Double door-8 way

Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:-

Double pole. Cat-A.

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required:-

Single pole. Cat-A.

Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required:-

Earthing with G.I earth pipe 4.5 mtr. long and 40mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as required.

Extra for using salt and charcoal for pipe earth electrode complete as required.

Supplying and laying 6 SWG G.I. wire at 0.50 mtr. below ground level for earth electrode conductor, including soldering etc. as required.

Providing installation testing and commissioning of ceiling fan with regulator including twiring the down rod of standard length (up to 30cm0WITH 16/0.20mm twin twisted flexible cotton braided copper ccotten braided copper cable including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc as required.-Ceiling Fan 1200 mm sweep, Category-A

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required:- Exhaust Fan, Light duty, (Domestic) 300 mm sweep