SPECIAL REPAIR TO COOK HOUSE AND ASSOCIATED AREAS OF OFFICERs MESS, PROVISION OF NEW DRAINAGE LINES AT CERTAIN PLACES IN OMQ AREA AND PROVISION OF SHED OVER VERANDAH IN CERTAIN OMQs AT AF STATION IZATNAGAR, BAREILLY.

Amount

M & L for providing plain cement concrete, type B-2, 1:2:4 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

S & F of steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS-1161(1979) grade St-240 complete all as specified and directed.

S & F of rolled mild steel plates (plain or chequered), channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410-W (Grade E-250) quality-A complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering complete all as specified and directed.

Fixing only pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet of any type and description with and including provision of self tapping screws complete all as specified and directed. NOTE: - OLD SHEETS OBTAINED FROM DISMANTLING SHALL BE USED UNDER THIS ITEM.

S & F of 0.50 mm thick pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F of 0.50 mm thick pre-painted galvalume aluminum zinc coating GI based plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L for preparation of new or previously untreated steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M & L for providing plain cement concrete type B-1, 1:2:4, (using 20 mm graded stone aggregate), as in copings, bed block for embedding hold fasts, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and directed.

Demolition of brick work or stone / boulder masonry including all quoins, arches, pillars, etc. built in cement mortar or cement lime mortar complete all as specified and directed.

M & L for brick work with fly-ash old size bricks having designation 75 conforming to IS-12894 (2002), straight or curved on plan exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M & L for brick work with fly-ash old size bricks having designation 75 conforming to IS-12894 (2002), straight or curved on plan and any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Taking down cement or cement lime plaster from brick or stone walls etc. including raking out joints, hacking for keys, scrubbing down with water etc. complete all as specified and directed.

M & L for rendering 15 mm thick cement plaster on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of newly plastered or un-plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M & L for preparation of new plastered or previously untreated surfaces of walls and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M & L for 15 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes finished even and rough complete all as specified and directed.

M & L for rendering 10 mm thick cement plaster on fair faces of brick work or concrete surfaces in cement mortar 1:4 on vertical surfaces of wall finished even and rough suitable for laying wall tiles complete all as specified and directed.

M & L for glazed ceramic coloured tiles 450 mm X 350 mm X 7 mm thick as on vertical surface of wall such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.11 Sqm but not exc. 0.18 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.38 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

S & F of 20 mm thick perfact black granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like, set in over and including 15 mm thick cement screed in cement mortar 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M & L for 18 – 20 mm thick machine cut Kota stone slab as in flooring over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including necessary grinding, rubbing, rounding to exposed edges and polishing in granite finish complete all as specified and directed.

M & L for providing and fixing 12 mm thick Gypsum Board as in ceiling fixed with screws as per manufacturer’s instructions complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards / slabs / blankets, any thickness including cover fillet complete all as specified and directed.

S & F of GI frame work for seamless ceiling grid of size 605 X 605 mm comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre, intermediate channel 0.90 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc. 1.20 m length) of 0.55 mm thickness having curled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete all as specified and directed.

S & F of solid PVC door frame of size 50 mm X 47 mm made out of 5 mm thick wood grain printed PVC sheet and edges will be painted to match with printed sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F of 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded wood grain printed PVC 'C' channel having a PVC sheet beading of size 15 mm X 5 mm thick stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of wood grain printed PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with decorative PVC beading of size 10 mm X 10 mm (900) and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F of factory made steel window with side hung shutters including projecting type hinges, steel handle, mild steel tower bolts and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S & F of factory made steel window with side hung shutters including projecting type hinges, steel handle, mild steel tower bolts and steel peg stay, without glazing bars complete all as specified and directed.

S & F of factory made steel ventilator with centre hung shutter including two pairs of brass pivots, catch spring and pulley wheel complete all as specified and directed.

S & F of mild steel framed work such as grills, gratings etc. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railing, frame work of water tanks and similar work conforming to Fe-290 Grade E-165 complete all as specified and directed.

S & F of galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

S & F in repairs galvanised mild steel wire cloth, 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / metal frames, glazed with oil putty or fixed with beads including punching or drilling out old glazing pins / spring clips and providing new glazing pins / spring clips complete all as specified and directed.

S & F of 4 mm thick plain, ordinary quality sheet glass and glazing with oil putty or fixed with wooden beads in square not exc. 0.5 sqm in each pane complete all as specified and directed.

S & F of 4 mm thick frosted type, ordinary quality sheet glass and glazing with oil putty or fixed with wooden beads in square not exc. 0.5 sqm in each pane complete all as specified and directed.

S & F in repairs vitreous china urinal partition, white of size 310 X 700 mm, slab terminating about 40 cm above finished floor level complete all as specified and directed.

S & F in repairs vitreous China half stall type white urinal (excluding flushing cistern, flush pipe and waste pipe) but including connections to flushing pipe and out going pipes etc complete all as specified and directed.

S & F in repairs vitreous china wash basin white, flat back, size 550 X 400 mm excluding taps, waste, chain and plug but with and including brass chromium plated waste coupling 32 mm size alongwith waste pipe of required size and length, fixing brackets, cutting for and pinning in as required complete all as specified and directed.

S & F in repairs water closet vitreous china squatting pan ‘Orissa’ pattern size 580 X 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and flushing pipe, anti-syphonic pipe etc. including lean concrete as required complete all as specified and directed.

S & F in repairs polymer white (polypropylene Delrin and ABS) low level flushing cistern 10 litre capacity valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, flush pipe, brass screws, handle etc complete having BIS description mark with IS: 7231 with and including 32 mm bore PVC flush pipe of suitable length complete all as specified and directed.

S & F in repairs 15 mm size bib tap standard of PTMT, any colour high pressure screwed for iron pipes (minimum weight 90 gram) complete all as specified and directed.

S & F in repairs 15 mm size stop valve of PTMT, any colour high pressure screwed for iron pipes (minimum weight 90 gram) complete all as specified and directed.

S & F of 450 mm long PVC connection with two Nos. PTMT nuts internally threaded and PVC washer suitable for 15 mm bore pipe line complete all as specified and directed.

S & F in repairs 32 or 40 mm dia PVC flush pipe of polyethylene of low or high density suitable for low level flushing cistern complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S & F in repairs 15 mm size swivel shower rose of PTMT, any colour (minimum weight 40 gram) with or with out swivel joint with and including 15 mm size, 195 mm long shower arm of PTMT, with bend of 45 degree with flange any colour (minimum weight 40 gram) and fixing to steel pipe or union complete all as specified and directed.

S & F in repairs mild steel chromium plated Harrison rails, with fixing brackets, stops, rollers etc. complete all as specified and directed.

S & F in repairs 20 mm dia brass chromium plated tubular towel rail 'D' type 60 cm long between flanges, including one pair of fixing brackets complete all as specified and directed.

S & F of 140 mm size (Overall length of cover plate) floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed.

S & F in repairs aluminium extruded sections body door closer hydraulically regulated designation No. 3, universal type suitable for door shutter 851 to 1000 mm in width and 61 to 80 Kg in weight complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking up or down 15 mm bore steel water tubing and connection complete all as specified and directed.

S & F of 15 mm bore steel water tubing medium grade galvanized with and including all fittings and fixed to walls and ceilings or laid under floors complete all as specified and directed.

S & F in repairs 500 Litre capacity rotational moulded polythene water storage tanks (cylindrical vertical with closed top) of specifications as per MES Schedule 2009, Part-I and hoisted, fixed in position complete all as specified and directed.

S & F of 20 mm dia ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gram) complete all as specified and directed.

S & F in repairs 20 mm bore gunmetal globe or gate valve, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S & F of 1.25 mm thick pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc. complete all as specified and directed.

S & F of 35 mm thick (Batten thickness) 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. divided into squares, without sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. and size of the members of shutter is as specified in clause No. 8.24 (a) of MES schedule 2009, Part-I (Specifications) complete all as specified and directed.

S & F of 300 mm long mild steel sliding door bolt, bolt type, stove enamelled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts complete all as specified and directed.

S & F of 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed.

S & F of 125 mm long mild steel pressed handle, oval type, stove enamelled black complete all as specified and directed.

S & F of 150 mm long (Length of bolt) mild steel barrel tower bolt stove enamelled black with bright bolt complete all as specified and directed.

S & F of 300 mm mild steel ordinary rat tail, rod pattern springs including roller and roller plate complete all as specified and directed.

M & L for preparation of new or previously untreated wooden surfaces exc. 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for vitrified ceramic 1st quality, nano polished, coloured tiles 10 mm thick (Square or Rectangular) polished, area of each tile not exc. 0.36 Sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

M & L for vitrified ceramic 1st quality, nano polished, coloured tiles 10 mm thick (Square or Rectangular) polished, area of each tile not exc. 0.36 Sqm, as on vertical surface of wall such as skirting, dado, riser etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed.

S & F in repairs 10 Litres capacity slim concealed in wall type PVC flushing cistern with and including flush bend, fixing frame, gasket and all other asseceries required to fix the same in wall complete all as specified and directed.

Excavation over areas not exc. 1.50 m deep and getting out in hard / dense soil complete all as specified and directed.

M & L for providing plain cement concrete, type C-2, 1:3:6 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M & L for rendering 10 mm thick cement plaster on fair faces of brick work or concrete surfaces with cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Removing surplus excavated material (SOIL) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

M & L for providing pre-cast cement concrete landing, cover slabs, chullah hoods, chajjas, shelves and similar items with plain faces in cement concrete 1:2:4 type B-1, using 20 mm graded stone aggregate and setting in cement mortar 1:4 complete all as specified and directed.

M & L for mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Excavation in post holes (or similar holes) each not exc. 0.50 Cum, getting out in soft / loose soil and removing surplus soil to a distance not exc. 50 m and making good surface complete all as specified and directed.

Cutting holes into or through brick walls built in cement mortar and making good the same in cement concrete 1:2:4 type B-0 or cement mortar 1:3 as required, superficial area of cutting not exc. 150 Sqcm complete all as specified and directed.

M & L for rendering 15 mm thick cement plaster on fair faces of brick work or concrete surfaces with cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed.

S & F of mild steel bolts, purpose made, with hexagonal or square head at one end and screwed the other or screwed both ends, each screwed ends to be fitted with washer and one hexagonal or square nut, exc. 30 cm long and dia of neck exc. 12 mm but not exc. 20 mm complete all as specified and directed.

Taking down carefully aluminium / copper point wiring (light point, fan point, socket outlet point or power point) any type (batten, surface conduit or concealed conduit) complete with and including fittings and fixtures such as switches, ceiling rose, pendent, lamp holder, regulator, switch, socket outlet, light fittings, shade conical etc. and separating serviceable fittings for reuse in the work as directed including removing of unserviceable fittings & fixtures with wiring cable, battens, wooden boards etc. from site and making good disturbed surfaces of walls, floors ceiling etc. complete all as specified and directed.

Taking down carefully old unserviceable sub main wiring of any description including batten or conduit complete all as specified and directed.

M & L for point wiring for one light point / fan point / bell point / 5 Ampere socket outlet point (independent point), controlled by one, one way switch with 1.50 sqmm size, PVC insulated, unsheathed 1100 volts grade single core multi-stranded copper conductor cable (FRLS) drawn into and including PVC conduit medium grade (not less than 20 mm dia) with and including its all necessary fittings and accessories fixed concealed with and including necessary chase cutting on brick / stone masonry walls and making good as per existing and sunk cast iron or 1.2 mm thick pressed steel terminal boxes for mounting fittings like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated sheet cover fixed with brass screws and cup washers including one continuous run of PVC insulated (green colour) 1.50 sqmm size stranded copper conductor cable (FRLS) as in earth wire and connecting all metal parts to common earth dolly complete all as specified and directed.

All as per item No. 88.00 hereinbefore but wiring for one 3 / 5 pin 5 Ampere socket outlet point on the same board, controlled with other switches complete all as specified and directed.

All as per item No. 88.00 hereinbefore but wiring for one 3 / 6 pin 15 Ampere socket outlet point on independent board and wiring using with 2.50 sqmm size cables complete all as specified and directed.

S & F of switch piano flush button single pole 230 volts, one-way 5 Ampere complete all as specified and directed.

S & F of socket outlet 5 Ampere, 2 and 3 pins (TOTAL 05 PINS), flush type 250 volts AC complete all as specified and directed.

S & F of lamp holder, PVC / polycarbonate type insulated body with back plate suitable for batten / angle fittings complete all as specified and directed.

S & F of ceiling rose surface bakelite, 65 X 50 mm, three terminals, PVC / polycarbonate insulated body complete all as specified and directed.

S & F of socket outlet two-in-one, 3 pin each suitable for 5 and 15 Amperes flush type, 250 volts AC complete all as specified and directed.

S & F of switch piano flush button single pole 230 volts, one-way 15 Ampere complete all as specified and directed.

Supply and fixing of single phase electric call bell, AC 230 volts complete all as specified and directed.

S & F of bell push button type single pole one-way 5 Ampere complete all as specified and directed.

S & F of electronic type fan regulator 230 volts, step type having five steps, switch type, hum free complete all as specified and directed.

S & F of 1100 volts grade heavy duty two single core PVC insulated (FRLS) copper multi-stranded conductor cable as in sub main wiring, drawn into & including PVC conduit medium grade not less than 25 mm dia including its all accessories & fittings, fixed concealed with and including chase cutting and making good the same as per existing specifications along with a continuous run of multi-stranded copper conductor PVC insulated (FRLS) (green colour) cable as earth wire complete all as specified and directed for the following: -

(a) 2 X 4.00 sqmm as main wires + 1 X 2.50 sqmm as earth wire.

(b) 2 X 6.00 sqmm as main wires + 1 X 4.00 sqmm as earth wire.

Taking down carefully ceiling fans, cleaning, oiling and greasing thoroughly including painting with one coat of synthetic enamel paint approved colour after cleaning and preparing the surface and re-fixing the same at existing site / rooms and connected with 23/0.0076 size three core PVC flexible cable from ceiling rose to connector of ceiling fan complete all as specified and directed.

S & F of wall / surface mounted type LED light fitting 1 X 20 watt (4 feet long), extruded aluminium batten with multiple lumen packages complete with all accessories internally pre-wired and including making electric connection with flexible twin core 1.00 sqmm size stranded copper conductor cable from light fitting to ceiling rose complete all as specified and directed. Make- Philips Cat. Part No. BN021C LED20S PSU CW GR S2 (SmartBright) of Philips or SLE BTN T8 20W (LED T8 AL Batten) of Surya.

S & F of retrofit type LED lamp 7 watt capacity complete all as specified and directed.

S & F of factory made V TPN DBs-DPX-160 MCCB DB's, 4 way, IP-43 protection-IK09 with metal door with 160 Amps copper busbar with 2 neutral busbar, earth bar cables ties for cable management fully insulated busbar with set of wires and door earthing for provision of DPX 160 MCCB and incomer and SP/TP MCB's as outgoing including dismantling of old unserviceable one complete all as specified and directed. (Cat. Part No. 607913 of Legrand or Cat. Part No. A9HVD04M of SCHNEIDER or Cat. Part No. CSDBMCCB225DD04IP43 of C&S)

S & F of flush mounting factory made Ekinoxe SPN DB's Double door, 8 way (Cat. Part No. 607711 of Legrand or Cat. Part No. A9HSND08 of SCHNEIDER or Cat. Part No. CSDBSPNDD08 of C&S), IP-43 Protection, IK-09 with metal door, with neutral bar, Earth bar and cables ties for cable management fully insulated bus bar including dismantling of old unserviceable one complete all as specified and directed.

S & F of MCCBs, 160 Ampere, DPX 160, 415 volts, 4 pole, 16 KA, thermal magnetic including dismantling of old unserviceable one all as specified and directed. (Cat. Part No. 420017 of Legrand or having same specifications in L&T or C&S).

S & F of MCB single pole and neutral, 240 volts, 32 to 40 Ampere breaking capacity 10 KA, ‘C’ Series including dismantling of old unserviceable one complete all as specified and directed.

S & F of MCB single pole 240 volts, 6 to 32 Ampere 50 Hz, 10 KA, ‘C’ series including dismantling of old unserviceable one complete all as specified and directed.

M & L for earthing complete with galvanised steel earth plate electrode 600 mm X 600 mm X 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of earth plate not less than 1.50 m below normal ground level, connected to galvanised earth lead 4 mm dia all as shown on electrical plate No. 3 of MES schedule 2009, Part–I (Specifications) and connected to main switch board / main DB’s / earthing test point including all necessary excavation and earth work in any type of soil, adequate quantity of charcoal dust & common salt all around the earth plate minimum 150 mm in all directions with & including watering pipe 20 mm dia GI medium grade, GI funnel made out of 0.63 mm thick GI sheet, wire gauge, 50 mm thick RCC cover in PCC 1:2:4, type B-1, duly reinforced with 6 mm dia mild steel TMT bars @ 150 mm both ways center to center with suitable lifting handle to cover, earth pit of PCC 1:2:4 type B-1, GI protection pipe light grade 15 mm bore including testing on completion of job complete all as specified and directed. NOTE: - ON TESTING AFTER COMPLETION OF JOB, IF DESIRED EARTH RESISTANCE (i.e. LESS THAN ONE OHM) IS NOT OBTAINED, THE EARTHING SHALL BE REDONE BY THE CONTRACTOR WITHOUT ANY EXTRA COST TO GOVT.

Supply and fixing of 1200 mm sweep 240 volts, AC having BEE 5 star rating ISI marked, off white coloured ceiling fan complete with fan blade, capacitor, canopy, down rod etc. with and including making electric connection with three single core flexible copper conductor cable of size 1.50 Sqmm from ceiling rose to connector of ceiling fan and writing MES No. with black synthetic enamel paint minimum font size 2.00 cm high complete all as specified and directed.

Supply and fixing of 400 mm sweep heavy duty metal body exhaust fan, single phase 230 volts AC, 900 RPM complete with and including all accessories, louver shutter and making suitable size hole for fixing of exhaust fan including making good the disturbed surface as per existing specifications, grouting of ragged bolts in wall for fixing of exhaust fan, frame, louvers and making electric connection with three single core flexible copper conductor cable of size 2.50 Sqmm from ceiling rose to connector of exhaust fan and writing MES No. with black synthetic enamel paint minimum font size 2.00 cm high complete all as specified and directed.

S & F of sheet metal enclosure with socket plug top and MCB single pole and neutral enclosure with a two pin and earth plug and socket complete with one No. single pole MCB 20 Ampere capacity 240 Volts as per Cat. Part No. 607841 of Legrand or CSDBPSSPN020 of C&S complete all as specified and directed.

S.M. KAZIM

M/S Quality Constructions

Zaigham Enterprises

M/s M Aali construction co

S.K.Enterprises