Treasury Infrastructure Development Project Providing and Installing Furniture for Sub Treasury Kollengode, Palakkad

Amount

Furniture : Civil works

Executive Chair-High back: Supply & installing of Executive Chairs as per the specification metioned below. Back Rest shall be high Back with Frame, Lumber Set, Headrest Outer and Joint made out of Nylon 6 (PA6+GF30%), Headrest shall be made out of Polypropylene and Mesh specification shall be 100% Polyester. The unit shall comply with the California technical bulletin 117 for flammability. Seat to Backrest Height shall be 725mm with Backrest Width of 535mm. The seat shall be Foam-Moulded PU with density not less than 50-60Kg/m3 with waterfall edge. Seat width shall be 470mm(clear width between arms), Depth including waterfall shall be 485mm. Head Rest shall be made out of Polyurethane of density not less than 45g/mm3. The Back tilt range shall be 16 Degrees with back tension adjustment knob. The chair shall be Tested for 3,00,000 Cycles as per ANSI BIFMA X5.1 -2002. Gas Lift shall be 3HP to absorb seating shocks with a higher stroke length of 120mm which shall be tested for 100000 cycles. All parts shall be BIFMA Compliant and shall be of approved make. The armrest shall be adjustable and made up of black integral skin polyurethane with 40-55 Shore Hardness and reinforced with 2mm thick M.S.-in-serts-Arm pad size 258mm (L) x 112mm (W). The armrests shall be fitted to the seat with seat/armrest connecting strip assembly made of 6mm thick. The armrest shall be height adjustable up to 80mm and back with adjustable up to 60mm. Arm rest shall be tested for 60,000 Cycles with load of 40Kg as per ANSI / BIFMA X5.1. Castor shall be Nylon with a diameter of 60 mm and shall be tested for 1,00,000 Cycles. The Base shall be glass reinforced Nylon Base with a pitch circle diameter of 658mm and shall be tested for a static load of 1450kg. The upholstery shall be fabrics with 100% polyester.The product shall be BIFMA compliant. The product shall be of approved make and colour. The model shall be Elate, Liberate, Aveo or equivalent

Staff Chair:- The outer and inner frame of the backrest shall be injection moulded in black polypropylene. Inner frame shall be upholstered with mesh fabric and assembled with the outer frame. The back shall have auto contoured lumber support for achieving comfortable seating posture. Lumber support shall be injection moulded in black polypropylene and upholstered with U foam. Lumber support shall be 160mm (W) x 90mm (H) at fixed position. Backrest size shall be 650mm (H) x 530 (W). The seat shall be made out of 12mm thick (7layers) hot pressed plywood and moulded seat foam upholstered with fabric. The bottom cover shall be injection moulded in black polypropylene to cover the plywood. Seat size shall be of dimension 495mm (W) x 510mm (D). Minimum and maximum seat height shall be 450mm and 550mm respectively. Seat Foam shall be made out of moulded polyurethane foam with the following properties: Density: 45 – 55 Kg/m3 Hardness: 15 – 20 Kgf Compression set: 50% 10 Max Tensile strength: 1.03 Tear strength (Min) : 2.0 N/cm Resilience : 50% - 60% Comfort / Indentation Hardness :15.4 .The armrest shall be adjustable and made out of black integral skin polyurethane with 45-55 Shore Hardness and reinforced with 4mm thick nylon in-sert. Arm pad shall be of dimension 265 x mm (L) x 95mm (W). The armrests shall be fitted to the seat with seat/armrest connecting strip assembly made of 30% Gas field nylon 20mm thick. Minimum and Maximum height of armrest shall be 280mm/360mm respectively. The front and back movement of armrest shall be 60mm. Armrest shall be tested for 60,000 Cycles to be completed with load of 40 Kg per arm. Conventional mechanism with one lever control for lock and seat height adjustment shall be provided. Mechanism made out of MS Plate thickness shall be 3mm and seat shall have a tilting angle of 3°to10° and back tilting angle of 87°to106° with back tension adjustment knob. Mechanism shall be tested for 3, 00,000 Cycles as per ANSI / BIFMA X5.1. All members shall be BIFMA compliant.GAS LIFT: Gas lift pipe shall be of diameter 50mm with height adjustment stoke of 112mm. Gas lift shall be tested for 1,00,000 Cycles as per ANSI / BIFMA X5.1. Meets DIN 4550 Class 4 and all applicable ANSI/BIFMA, EN performance standard. The base base shall be injection moulded in black 30% glass filled nylon and fitted with 5nos twin wheel castors. The base shall be 660 pitch circle diameter. The bases shall be tested for static load of 1250kg. The twin wheel castors shall be injection moulded in Nylon with a diameter of 60 mm. The castors shall be tested for 100000 cycles as per ANSI/BIFMA X 5.1. The Seat Fabric shall be of 100% polyester with an abrasion less than 96,000. Flammability: Adheres to BS EN 1021-1 1994 (Cigarette) Adheres to BS 7176:1995 (Low Hazard) Color Fastness to Light : Adheres to : 3+ [BS 1006 (1990)] Rubbing : Adheres to Dry: Class 3 Adheres to Wet: Class 3 The Backrest mesh shall be of 100% Polyester with a weight of 320 GLM and an abrasion of 80000 : Content: 100% Polyester Weight: 320 GLM Abrasion: 80,000 Flammability: BS EN 1021-1 1994 (Cigarette) BS 7176:1995 (Low Hazard) Color Fastness to Light: 4.5+ [BS 1006 (1990)].The models shall be Anatom, That's it, Oxbo or equivalent.

Dining chair: Providing and Installing in position cafeteria Chair with Single moulded construction made out of High performance Plastic.The mould shall be of thickness 200mm. The chair shall be tested for a vertical load of 300 Kgs with high UV stability and scratch resistant surface.The chairs shall be stackable and of approved color and make. The models shall be waffle,tang or equivalent.

3 seater Visitors Chair - Providing and installing 3 Seater Visitors chair with the following specification. Seat,arms & legs shall be made out of stainless steel 304 grade. The seats shall be connected using a centre beam made out of stainless steel 304 grade with armrest at either ends. The seats shall be of approved make and colour. 3 Seater size - 1765 (w) x 710 (d )x 775mm (ht)

Visitor chair (single):Providing & installing in Position Medium Back Visitor Chair with the following specifications. Seat & Back shall be Fabric upholstered/Mesh Back with 100% Polyester and weighing 320 GLM. Seat Foam shall be made out of PU foam with a density 50-60 Kg/m. Base shall be Mild Steel 4 Legged base powdercoated mounted on PVC bush. The Back rest shall be of dimension 610mm (H) X 425mm (W). Seat Size shall be of dimension 455mm (W) X 480mm (D). The product shall be BIFMA compliant.The chair shall be of approved make and colour.The models shall be Mint, Astro, Oxbo or equivalent

Officer's Table (STO):- Material using A Grade 18mm Rubber wood with melamine polish,Top both edge using double thickness,leg front side using 5cm box,using 7.2mm Golden steel beeding horizontally on the front panel,Providing CPU Stand ,Keyboard tray, Foot rest etc Approximate Size: 120 - 180CM X 75 - 90CM X 75CM (Size as per site conditions)

Side Table (STO) :- Material using A Grade 18mm Rubber wood with melamine polish.Providing shelfs,vehicle legs,Sliding doors etc back panel using 12mm A Grade 18mm Rubber wood. Hardware using Sliding channels, Multipurpose lock, Inser-t Handles etc - Make - Ebco. Unit fully installed by Knockdown fitting-Minifix system Make - Ebco -Size: 80 - 120CM X 45CM X 75CM (Size as per site conditions)

Workstation Counter Unit:- Material using A Grade 18mm Rubber wood with melamine polish,Top both edge using double thickness,leg front side using 5cm box,using 7.2mm Golden steel beeding horizontally on the front panel,Providing CPU Stand ,Keyboard tray,Foot rest etc Approximate Size: 100 - 180CM X 60 - 90CM X 75CM (Size as per site conditions)

Guard table :- Material using HMR Grade (Humidity & Moisture Resistant) (Make - Century Ply) Prelaminated Particle Board 25MM Thick for Table top , Leg etc. Front panel using 18MM Thick HMR Grade Prelaminated Particle board. Front panel inserted 20CM from the top end and using 7.2MM Golden steel beeding 3 Strip horizontally on the panel. All the visible edges using PVC Edge Band tape 2 x 30MM & 2 X 22MM, .5 X 22MM Wherever required. Providing PVC Keyboard tray & Cable manager : Make - Ebco & CPU Stand using 18MM Thick HMR Grade board. Exclusive of Pedestal Unit. Unit fully installed by knockdown fitting - Minifix system Make - Ebco.Approximate Size: 90 - 120CM X 60 - 90CM X 75CM (Size as per site conditions)

Cashier Table :- Material using A Grade 18mm Rubber wood with melamine polish,Top both edge using double thickness,leg front side using 5cm box,using 7.2mm Golden steel beeding horizontally on the front panel,Providing CPU Stand ,Keyboard tray,Foot rest etc Approximate Size: 120 - 150CM X 60 - 90CM X 75CM (Size as per site conditions)

Side Table Unit :- Material using A Grade 18mm Rubber wood with melamine polish,Top both edge using double thickness,leg front side using 5cm box,using 7.2mm Golden steel beeding horizontally on the front panel,Providing CPU Stand ,Keyboard tray,Foot rest etc Approximate Size: 120 - 150CM X 60 - 90CM X 75CM (Size as per site conditions)

Help desk :-Material using A Grade 18mm Rubber wood with melamine polish,Top both edge using double thickness,leg front side using 5cm box,using 7.2mm Golden steel beeding horizontally on the front panel,Providing CPU Stand ,Keyboard tray,Foot rest etc; Approximate Size: 90 - 120CM X 60 - 90CM X 75CM (Size as per site conditions)

Glass partition for linear work station Over Main table-Providing and installing 10mm thick toughened glass partition with etched boarders and bevelled edges as per the drawing for an overall height of 530mm at the center and 400 mm at both ends,fixed to MDF Exterior Grade/ HDF 72MM Square tubular posts at either ends using patch fittings and providing a pegeon hole of 200mm x100 mm as per the approved sketch. Contractor shall submit and take approval for the shop drawing before fabrication.

Glass Partition between work stations:-Providing and installing 10mm thick toughened glass partition with etched boarders as per the drawing for a height of 400mm fixed to MDF Exterior Grade/ HDF 72MM Square tubular posts at either ends using patch fittings and providing a pegeon hole of 200mm x100 mm as per the approved sketch. Contractor shall submit and take approval for the shop drawing before fabrication.

Floor mounted Storage:- Material using HMR Grade (Humidity and Moisture Resistant) (Make - Century Ply) Prelaminated Particle Board 18MM Thick for Side leg,Top, Shelfs, Doors,Skirting etc. Back panel using 9MM thick Pre Laminated HMR Grade board. All the visible edges are covered with PVC Edge Band tape 2X22MM, .5X22MM Wherever ever required. Hardware using Auto Close hinges, Multipurpose lock, D Handles etc Make - Ebco. Unit fully installed by knockdown fitting - Minifix system Make - Ebco.Size: 90 - 240CM X 45CM X 90 - 240CM (Size as per site conditions)

Floor mounted Storage(Guard Room): Material using HMR Grade (Humidity & Moisture Resistant) (Make - Century Ply) Prelaminated Particle Board 18MM Thick for Side leg,Top, Shelfs, Doors & Skirting etc. Back panel using 9MM thick Pre Laminated HMR Grade board. All the visible edges are covered with PVC Edge Band tape 2X22MM, .5X22MM Wherever ever required. Hardware using Auto Close hinges, Multipurpose lock, D Handles etc Make - Ebco. Unit fully installed by knockdown fitting - Minifix system Make - EbcoSize: 45- 60CM X 45-60CM X 210CM (Size as per site conditions)

Pedestal Unit:- Material using A Grade 18mm Rubber wood with melamine polish.Providing 1 Drawer and one open door.Back panel using 12mm A Grade Rubber wood.Hardware using Auto Close hinges, Multipurpose lock, Sliders & D- Handle etc Make- Ebco. Unit fully installed by Knockdown fitting-Minifix system Make-Ebco.-Size:- 40x45x70CM

Providing and installing in position Dining table of size 1800mmx750mmx740mm high with the following specification. The table top shall be made up of 18mm thick PVC Polyester resin in an extruded polymer profile (Multiwood or equivalent) of approved colour with 8mm thick toughened glass top with bevelled edge. All exposed edges shall be finished with 2mm thick PVC edge banding on both sides. Table top shall be mounted on 50mmx50mmx2mm thick MS tube frame supported with legs made of 50x50x2mm thick Square MS tubes powder coated with Tie member made out of 40mmx80mmx2mm thick rectangular powdercoat finished with minimum of 60 microns thickness finished of approved colour. Contractor shall submit and take approval for the shop drawing before fabrication. Table Dining:- 1800mm X 750mm X 740mm.

Wall mounted writing table: Providing and installing in position wall mounted writing table with storage of size 1200mm L X 400 mm W X 400MM H as per the drawing. The table top and storages shall be made of 16mm thick BWP 710 grade Marine Plywood of approved make and colour and wall mounted with side brackets 300mm wide and 300mm high using anchor screws. 3 nos storages of size 300X100X150mm. All exposed edges shall be finished with 2mm thick PVC edge banding on both sides. All hardwares shall be of approved make. Contractor shall submit and take approval for the shop drawing before fabrication .Wall Mounted writing table with storage :1200(W) X400 (D) Installing hight 1100 mm from Floor level.

Supply and Installation of single cot as per the following specification. The frame shall be made up of 25mmx50mmx2mm thick MS square tube with powder coated finish supported on 40mmx40mmx2mm thick MS legs of same finish. The single cot shall be finished with treated country wood planks 20mm thick joint to form a single slab, properly finished with one coat of sealer and polish. Contractor shall submit and take approval for the shop drawing before fabrication.single cot:- 1800mmx750mmx500mm(H)

Providing and installing cashier's counter as per the following specification.The counter shall be made of Aluminum grill and 12mm thick BWP 710 grade Marine Plywood supported on aluminum chanels using anchor screws as per drawing.An outward as well as inward projection of 300mm wide and 1500mm long to be provided with 12mm thick BWP 710 grade Marine Plywood shall be provided at a height of 1200mm from floor level . All the exposed sides shall be provided with 1mm thick laminate of approved make and colour . The laminates shall be installed using hot pressed machine in a factory. Contractor shall submit and take approval for the shop drawing before fabrication.

Providing & supply of Compactors as per dimension shown in layout with the following specifications:Constrcution: Rigid upright frame made out of 1.2mm thk CRCA steel box pipe.Upright with 25x50mm rectangular slotted pipe with cladding material of 0.7mm CRCA sheet.Complete construction in knock down design for easy handling & design is scalable to add bays in row wise or column wise subsequently.Shelves:Each unit has 6 loading levels formed by 5 loading shelves with a UDL(Uniform distributed load) of 80Kg capacity , 438mm depth,made of 0.8mm CRCA with stiffner.Shelves are mounted on support brackets & adjustable with a pitch of 25mm. Track Material:Aluminium track material with complete track assembly on self suppported design.making the installation grouting free.25mm thk prelaminated particle board walkway to be provided for easy access. easily adjustable levellers required to keep platform & track parallel on uneven surfaces.Sloping ramp in aluminium for easy trolley access & reduced tipping hazard.Pulley belt mechanism for reduced noiseless & oil free operation.Ergonomic plastic handle with buit in safety lock mechanism.Central locking to be provided on last unit to lock the entire assembly.Compactor Ht from ground is 2100mm(1985mm body+75mm undercarrriage+40mm channel system).All metal components to be given anti rust surface treatment & powdercoated with epoxy polester powder with a DFT of 60-80 microns.Rate for 1 bay drive type with One number Single static+One number single end + one Number twin mobile unit.

Vertical Blinds:-Providing and Fixing 100mm wide vertical blind of approved make and colour as per the instruction of Engineer in charge

Reflective sun Film for window -Providing and installing reflective sun films with 8% visible light transmittance and 18% of visible light reflectance. The solar light transmittance should be 9% and 57% of solar light reflectance .The ultra violet transmittance shall be 2% and 91% of glare deduction. The film shall be provided with 0.26 shading coefficient and an emissivity of 0.6. Total solar energy rejection shall be 76%. The film should be of approved make and colour.(Approved brands-3M,Garware )

Signages-Design Charge,Transportation & Erection charges

Supply and installing steel Slotted Angled Iron Rack with 6 Pannel (1800x900x380 cm) 20g

Supplying and fixing logo 600 mm dia, engraved on 18 gauge thick stainless steel plate 304 grade aas per approved drawings and specifications

Signages-Supplying and providing signages as directed by Engineer incharge . Door Signages( acrylic & vinyl sticker)

Signages-Supplying and providing signages as directed by Engineer incharge .Toilet Signages ( acrylic & vinyl sticker 16" x 4")

Signages-Supplying and providing signages as directed by Engineer incharge Table Top Signages ( aluminum profile & vinyl 12" x 4")

Signages-Supplying and providing signages as directed by Engineer incharge .Wall mounted Signages ( aluminum profile & vinyl 16" x 4")

Signages-Supplying and providing signages as directed by Engineer incharge for Counters & Door Signages(push & pull -vinyl sticker 16" x 4")

Signages-Supplying and providing signages as directed by Engineer incharge for Cash Counter ( acrylic & vinyl 24" x 4";)

Supplying 8mm thick tinted clear glass with bevelled edges for table top.

Supplying velvet table cloth of approved make and colour.

Supplying, fabricating and installing 20' x 4' single side non lit sign Board with following specifications:Frame : 1" 18gauge square pipe frame primed and painted , Fascia : 3M Panagraphic III flex with 3M 3630 vinyl as per approved design,colour and drawing including transportation,scaffolding and unloading charges etc. complete as per the direction of Engineer in charge.

Cable Management System- Furniture

90.9.2.1 : Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required.100 x 50 mm CMS with base and lid

90.9.2.2 : Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required. Cable dIvider

90.9.2.4 : Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required. Flat angle 90 degree

90.9.2.5 : Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required. Internal angle 90 degree

90.9.2.6 : Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required. Internal coupler

90.9.2.8 : Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the following accessories conforming to IEC 61084/ BS 476 & 4678 on surface / recess including cutting the wall and making good the damages in case of recessed installation as required. End cap

Supply and fixing of DLP-S 2 MODULES FRAME for mounting wiring accessories in existing truncking system.

Supply and fixing of DLP-S 4 MODULES FRAME for mounting wiring accessories in existing truncking system.

Supply and fixing of DLP-S 6 MODULES FRAME for mounting wiring accessories in existing truncking system.

Supply and fixing of METAL HEIGHT ADJUSTABLE JUNCTION BOX OF SIZE 150X150X 45-90 MM

Supply and fixing of METAL HEIGHT ADJUSTABLE JUNCTION BOX OF SIZE 200X200X 45-90 MM

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

Macro Enterprises

Muralidharan

Bidder Name

Macro Enterprises

Muralidharan

Ashly Furnishing Co Pvt Ltd