KFRI/ENGG/GOI RP- 847/ 22/2023-24

Amount

Dismantling brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge. In cement mortar

Dismantling roofing including ridges, hips, velleys and gutters etc., and stacking the material within 50 metres lead of : G.S. Sheet

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth,

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Lintels, beam, plinth beams, girders, bressumers and cantilevers

Suspended floors, roofs, landings, balconies and access platform

Stair

Reinforcement for R.C.C works,bent, tied and placed in position using torsteel

Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). using good quality Vengai wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of I st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing aluminium work for door, windows, ventilators and partitions with extrudeed built up standard tubular sections/ appropriate 5mm thick lip kitchen cabinet sections and other sections of approved make, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading to glazing / paneling C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. including Glazing, paneling with5.5mm float glass panes. Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding. Using 10mm dia round bar with MS flat 32mm x 6mm

Providing and fixing M.S. grills of required pattern in frames of windows etc.using 6mm dia MS rod 3" pictch( diagonal Pattern ) nominal size etc. and frame with 1"x1" x 6mm MS angle including priming coat with approved steel primer all complete. As per direction of Engineer incharge

Supplying and fixing PVC door with frame of single sheet, printed type standard quality to suit the door opening (80*210cm) including cost of all materials and labour charges, conveyance etc. complete as per direction of Engineer - in charge.

12mm cement plaster cement of mix : 1:4 (1 cement: 4 fine sand)

9 mm cement plastering of mix : 1:3 (1 cement : 3 fine sand ) including all cost of materials, labour charges etc complete

12 mm cement plaster finished with a floating coat of neat cement of mix: 1:4 ( 1 cement : 4 fine sand)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including (using pvc spacer while laying )grouting the joints with epoxy pigments etc., complete. Size of Tile 600 x 600 mm.

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600x600 mm

Providing and laying vitrified anti skid floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing vitrified glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge. Granite work

Finishing walls with Premium Arcylic smooth Exterior paint with Silicone additives of required shade, New work (two or more coats applied @1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm

Painting two coat with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Steel work in built up tubular (square, rectangular or round hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Roofing with Galvanized iron color coated trafford sheets 0.50mm (including colour coated G.I ridge, hip and valley sheets, j-bolts, washers etc) on a frame work of M.S. rectangular pipes (B-class) m.s rods, iron plates, etc. ( already done and paid seperately) with over laps of 150mm at the ends all cost of materials conveyance and labour charges etc complete all levels as per direction of engineer in charge.

Providing and fixing white vitreous china pedestal type water closet (European type, single unit air sucking ) with seat and lid, flushing cistern,( including flush pipe, with manually controlled device , conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x400mm with single 15 mm C.P.brass pillar taps

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 8931 15 mm nominal bore

Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

Providing and fixing C.P long body bib cock ( Lab tap)of approved quality conforming to IS standard and weighting not less than 690 gms 15mm nominal bore

Supplying and fixing 110mm SS Floor trap with gratings, including all cost of materials, labour for fixing , cutting the floor and making good etc. complete.

Supplying and fixing SS Towel rod 75cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

fixing following dia pipes and specials (bearing ISI mark) finolex/supreme or equivalent quality including necessary specials such as bends,tee,elbow etc fixed with M.S clamps (@1.5mtr intervals or as directed ) labour charges .Supplying and laying 110mm PVC 6Kgf/Cm2 pipes and specials

Supplying and laying 63mm PVC 6Kgf/Cm2 pipes and specials

Supplying and laying 32mm PVC 6Kgf/Cm2 pipes and specials

Supplying and laying 25mm PVC 6Kgf/Cm2 pipes and specials

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Providing and laying plain cement concrete 1:3:6 using 20 mm nominal size broken stone, laying to line and level, consolidating, watering, curing, form work, all cost of materials, conveyance, scaffolding etc.complete at all levels.

Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

Providing andfixing GI pipes for Truss support- 3" GI (Medium )Pipe

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Painting two coat with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

Roofing with Galvanized iron color coated trafford sheets 0.50mm (including colour coated G.I ridge, hip and valley sheets, j-bolts, washers etc) on a frame work of M.S. rectangular pipes (B-class) m.s rods, iron plates, etc. ( already done and paid seperately) with over laps of 150mm at the ends all cost of materials conveyance and labour charges etc complete all levels as per direction of engineer in charge.

Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

supplying and fixing all side including buffer room and gate 200micron UV stabilized, 5 layer 90% transmission polyfilm on the GI truss using double spring locking 0.8mm thick, smooth edges, flat bottom and PVC coated zig-zag springs of 2.2mm dia and excettents elasticity without damaging the poly film. The channels fixed on the trussess using self drill screws galvanized with hex washer.

12mm cement plaster finished with a floating coat of neat cement of mix :1:4(1cement : 4 fine sand)

Finishing walls with Premium Arcylic smooth emulsion paint of approved brand and manufacture to give an even shade, New work (two or more coats applied @1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm

Fogging & misting System: Specification: Through Micro Humidification system to create the 75% ±5% humidity:-Installation with leakage Prevention device ( LPD) fogger does not drip during the function . including necessary pipelines of 32mm dia 10kgf, storage tank of 500 ltr, timer etc. Working pressure - 4 bar at this pressure, the average droplet size :- 50 to 100 m. Density :- One fogger to 0.3 m – 0.4 m² for propagation. (min 15 Nos foggers) Type of fogger : Cross way nozzle ,hanging type. fogger discharge range:-7.0 LPH Pipe: - 16 mm LLDPE ( 10 kg/cm² ) colour BLACK - 3 line of total 33m length.

EDATTU CONSTRUCTIONS

Suresh