Renovation and Interior Fit-Out Works of SIDBI Branch Office, Rajkot

Sr.No Description DSR Amount Non- DSR Amount

1 Civil & Interior Work 20,83,684.43 17,57,450.78

2 Electrical Work 8,01,410.66 571577.00

5 Fire Fighting Work 45,723.74 38494.00

6 CCTV Work 90400.00

7 Furniture Work 2429210

8 Lighting Work 1,17,140.00

15 Grand Total 1,01,63,906.90

15 Grand Total 1,01,63,906.90

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - CIVIL WORKS

S NO DSR/MR DESCRIPTION UNIT RATE AMOUNT AMOUNT

DSR RATE NON DSR

1 FLOORING WORKS

ALUMINIUM SKIRTING: Supply of 100mm Aluminium (Grade 6063) Skirting with

15 micron anodising In Natural Finish. Thickness 1.30 to 1.50mm. Designed to

conceal screws. Seamless finish. Complete with Rubber/ PVC Jointers and

Supplying and fixing of 3mm Luxury vinyl flooring Top layer of approved design

& Pattern as per architects approval & Instructions

CARPET TILES: Providing and laying carpet tile flooring. Carpets shall be of Type

6 nylon loop pile carpet tiles/Plank. The carpet shall have sufficient gauge

(1/10 ~ 1/12) with sufficient stitches (10~13) per inch. The carpet shall be

1.03 MR solution dyed fibre content or with injection printing technology. The carpet 22.00 sq m 1650.00 36,300.00

shall have the pile height ranging from (2.0 ~ 3.0) mm with average

density higher than 4500 Oz/ cubic yard. The total thickness of the carpet

tile shall also range from (5.5 ~ 6.0) mm.

LAMINATED WOODEN FLOORING Providing and laying 8.3mm thick AC5 grade

laminate wooden flooring having good castor chair and furniture resistance

strength. Plank dimension to be 1215x195x8.3mm with valinge clock locking

system and wax coating for better sound resistance. Impact and abrasion

resistance to be of high grade having class EN 13329. The flooring shall be laid

with 2mm thick underlay and PVC sheet and prevent against moisture and

1.04 MR foot taping sound. The item also includes the skirting and any other profiles 110.00 sq m 1770.00 1,94,700.00

required for proper installation.or its equivalent specifications or as per the

selection of client and items shall be complete in all respects. or its equivalent

specifications/ size as per the site requirement or as per the selection of client

and items shall be complete in all respects.

2 FALSE CEILING WORKS

Digitally signed by AMIT

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height

including providing and fixing of frame work made of special sections,

power pressed from M.S. sheets and galvanized with zinc coating of 120

gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of

size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at

1200 mm centre to centre, one flange fixed to the ceiling with dash

fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat

fixed to the angle hangers of 25x10x0.50 mm of required length with nuts &

bolts of required size and other end of angle hanger fixed with intermediate

G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to

centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm

with tapered flanges of 26 mm each having lips of 10.5 mm, at 450

mm centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230

mm long G.I. wire at every junction, including fixing perimeter channels 0.5

mm thick 27 mm high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450

mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing

of gypsum board to ceiling section and perimeter channel with the help of dry

wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing

to a flush finish of tapered and square edges of the board with

recommended jointing compound , jointing tapes , finishing with jointing

compound in 3 layers covering upto 150 mm on both sides of joint and two

coats of primer suitable for board, all as per manufacturer's specification

and also including the cost of making openings for light fittings, grills,

diffusers, cutouts made with frame of perimeter channels suitably fixed, all

complete as per drawings, specification and direction of the Engineer in

Charge but excluding the cost of painting with

Digitally signed by AMIT

Providing and fixing mineral fibre false ceiling tiles at all heights of size

595X595mm of approved texture, design and pattern. The tiles should

have Humidity Resistance (RH) of 99%, Light Reflectance ≥

85%,Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as

per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-

Grid of hot dipped all round galvanized iron section of 0.33 mm thick

level suspended on interlocking T-Grid of hot dipped all round

galvanized iron section of 0.33 mm thick5x32mm of length 1200 mm

and secondary intermediate cross T of size 15x32 mm of length 600 mm

to form grid module of size 600x600 mm suspended from ceiling using

galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer

diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod

2.02 26.27 up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm,

spaced at 1200 mmcentre to centre along main ‘T’. The system should

rest on periphery walls /partitions with the help of GI perimeter wall

angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed

to the wall with help of plastic rawl plug at 450 mm centre to centre &

40 mm long dry wall S.S. screws. The exposed bottom portion of all T-

sections used in false ceiling support system shall be pre-painted with

polyester baked paint, for all heights. The work shall be carried out as

per specifications, drawings and as per directions of the engineer-in-

With 15 mm thick beveled tegular mineral fibre false ceiling tile (NRC

3 PARTITIONS AND WALL CLADDING - -

Digitally signed by AMIT

WALL PANELING :-Providing and fixing Paneling upto ceiling height

consisting of Aluminium frame and required board, frame work made of

Aluminium section made of 50x25 mm , consisting of floor and ceiling channel

50mm wide having equal flanges of 25 mm and 0.50 mm thick, fixed to the

floor and ceiling at the spacing of 610 mm centre to centre with dash fastener

of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal

screws with nylon plugs and the studs 48 mm wide having one flange of

34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within

flanges of floor and ceiling channel and placed at a spacing of 610 mm

centre to centre by 6 mm dia bolts and nuts, including fixing of studs

along both ends of partition fixed flush to wall with suitable anchor fastener or

metal screws with nylon plugs at spacing of 450 mm centre to centre, and

MR fixing of boards to both side of frame work by 25 mm long dry wall screws on - -

studs, floor and ceiling channels at the spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to avoid

through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two

flanges of 9.5 mm each) to be provided at the horizontal joints of two boards,

fixed to the studs using metal to metal flat head screws, including

jointing and finishing to a flush finish with recommended jointing compound,

jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher

as per manufacture's specification and direction of engineer in charge all

complete.(Cost of Aluminium framing 600X600mm Paid saperately)

Paneling with 12 mm thick HDHMR board to IS: 5509 60.00 sq m 2,414.28 144856.86

Digitally signed by AMIT

WALL PARTITION-Providing and fixing partition upto ceiling height

consisting of Aluminium frame and required board, frame work made of

Aluminium section made of 50x25 mm , consisting of floor and ceiling channel

50mm wide having equal flanges of 25 mm and 0.50 mm thick, fixed to the

floor and ceiling at the spacing of 610 mm centre to centre with dash fastener

of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal

screws with nylon plugs and the studs 48 mm wide having one flange of

34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within

flanges of floor and ceiling channel and placed at a spacing of 610 mm

centre to centre by 6 mm dia bolts and nuts, including fixing of studs

along both ends of partition fixed flush to wall with suitable anchor fastener or

MR metal screws with nylon plugs at spacing of 450 mm centre to centre, and - -

fixing of boards to both side of frame work by 25 mm long dry wall screws on

studs, floor and ceiling channels at the spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to avoid

through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two

flanges of 9.5 mm each) to be provided at the horizontal joints of two boards,

fixed to the studs using metal to metal flat head screws, including

jointing and finishing to a flush finish with recommended jointing compound,

jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher

as per manufacture's specification and direction of engineer in charge all

complete.(Cost of Aluminium framing 600X600mm Paid saperately)

Both side 12 mm thick HDHMR board to IS: 5509 80.00 sq m 3970.12 317609.6

LAMINATE CLADDING- P/F 1mm thick laminate including 4 mm thick

MDF, on an existing Plywood surface.

Providing and fixing 12mm thick frameless toughened glass

door shutter of approved brand and manufacture, including providing and

fixing top & bottom pivot & double acting hydraulic floor spring type fixing

21.18 arrangement and making necessary holes etc. for fixing required door fittings, 160.00 sq m 5325.9 852144.00

all complete as per direction of Engineer in charge (Door handle, lock and

stopper etc. to be paid separately)

Providing wood work in frames of doors, windows, clerestory windows and

other frames, wrought framed and fixed in position with hold fast lugs or with

9.1 dash fasteners of required dia & length (hold fast lugs or dash fastener - -

shall be paid for separately).

9.1.1 Second class teak wood 1 cum 142949.7 142949.70

INSULATION- Providing and fixing thermal insulation with Resin Bonded rock

wool conforming to IS: 8183, having density 48 kg/m3,50 mm

thick,wrapped in 200 G Virgin Polythene Bags fixed to wall wirh screw, rawel

plug & washers and held and in position by criss cossing GI wire etc. complete

as per directions of Engineer-in-Charge.

Digitally signed by AMIT

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part

I) non-decorative type, core of block board construction with frame of 1st

9.21 class hard wood and well matched commercial 3 ply veneering with vertical -

grains or cross bands and face veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary

Providing and fixing aluminium extruded section body tubular type

universal HS 3000 Slimline Concealed Door Closer (having brand logo with ISi,

IS : 3564,embossed on the body, door weight upto 36 kg to 80 kg and door

widthfrom 701 mm to 1000 mm), with double speed adjustment with necessary

accessories and screws etc. complete

TOWER BOLTS:- Providing and fixing aluminium tower bolts, ISI

9.97 marked, anodised (anodic AC 10 as per IS : 1868 ), transparent or dyed to -

required colour or shade, complete:

9.82 DOOR STOPPER:- Providing and fixing bright finished brass hanging type floor

door stopper with necessary screws, etc. complete. 10 EACH 121.65 1216.50

MR MORTICE LOCK AND LEVER HANDLES- Providing and installing Tubular

Handle TH 123 with Roses & Escutcheon in SS packaged with Mortice

lockset 55mm backset, 20 SS forend, SS strike plate and EP Cylinder for all flush 10 EACH 2,650.00 26,500.00

MR Providing and Fixing ESDH 22x450 mm D-type Handle Material :

Stainless Steel. Finish : Satin Stainless Steel (SSS). of approved make and

model all complete as per the direction of Engineer-in-charge. 10 EACH 3,450.00 34,500.00

MR Providing and fixing minimium 100 kg capacity flooor spring for Doors

approved make and designs as per engineer in charge 11 EACH 8,000.00 88,000.00

MR Providing and fixing Glass door lock approved make and designs as per

engineer in charge 11 EACH 750.00 8,250.00

Providing and applying plaster of paris putty of 2 mm thickness over

13.26 plastered surface to prepare the surface even and smooth complete. 250 sq m 262.70 65675.00

Wall painting with premium acrylic emulsion paint of interior grade,

having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of

13.83 approved brand and manufacture, including applying additional coats

wherever required to achieve even shade and colour.

13.83.2 Two coats

Digitally signed by AMIT

Applying priming coats with primer of approved brand and manufacture,

13.85 having low VOC (Volatile Organic Compound ) content.

13.85.1 With ready mixed pink or grey primer on wood work (hard and soft wood)

having VOC content less than 50 grams/ litre 281.8 sq m 70.35 19824.63

BLINDS Providing & supplying of Window Blinds as per the approved

sample in required shade and style consisting, of ZEBRA BLINDS comprising of

optima screen Fabric comprising of 22% polyester, 78% PVC, Fabric weight 460-

480G weight per sq m, Thickness 0.67 mm, Yarn count 18- 19/cm, having fire

resistance standard – NFPA 701-89 small testing ISO- 5659-2 .Thetear resistance

should be complying to ISO4674 & breaking resistance – ISO 5081. The DRIVE

UNIT shall be of clutch for quick, easy and safe installation, moulded plastic

with steel spring support and inserted into the tube end. It shall be driven by a

ball chain pulley with ball chain and can be positioned at right side or left

hand side of the Shade. The Shade when lowering or raising, shall be

automatically locked in position upon release of the ball chain by means of a

built in friction lock.Universal clutch for left and right hand operation.Chain

M.R. Gear Ratio of 1.75:1. The END PLUG shall be molded of plastic witha steel 50 sq m 1,650.00 82500

location pin.The plug shall be inserted into the tube end.(Opposite to the Drive

Unit) for ease of installation. The SUPPORT BRACKETS shall be of coated steel &

provided with covers and used in right hand or left hand positions

differentiated by the acceptance of the of the rectangular drive unit support

or the round idler plug pin.Can beinstalled (a) On Face (b) Ceiling Mount (c)

(d) in Recess. The Bracket should be protruding outside maximum of

80mm.The ROLLER TUBE shall be of extruded aluminum with 37mm internal

diameter & skin thickness of 1mm and shall incorporate a key way integral

with the tube to accommodate the spline. The BOTTOM RAIL shall be a Flat

Bottom made up of powder coated steel. The BALL CHAIN shall be 2mm

diameter cord with 4.5mm diameter acetal balls moulded co-axially to it on

6mm pitch to form an endless ball chain. It is used for raising or

M.R. FROSTEDFILM(CRYSTALQUALITY):-Providing and fixing scotchcal over glass

surface as approval of the Architect. (Only film surface area shall be 45 sq m 1,650.00 74250

measured and paid).

Cabinet Shutters out of 19mm Commercial Plybaord finished in 1mm

Laminate of matching, Shutters to be fixed to a frame. Rigidly fixed on both

sides and top finshed in laminate. No internal carcass required. All Hinges of

MR hettich or equivalent. Internal Surface of the shutter in balancing white 10 sq m 11,500.00 115000

laminate. All shutters to be provided with Stainless steel louvers at the top and

bottom of the shutter as per the site requirements and instrcution of the

Engineer In charge.

Digitally signed by AMIT

Providing and Fixing Logo & Signage in 3D ,as per the approved Design/ pattern with

Mat /Gloss Finish Brass Letters with Mettalic/ Acrylic Base, complete as required

at site with the direction of the Enginner In Charge

Providing & fixing Sidbi Sign Glow Board For Exterior Acrylic Base Embeded

MR Letter as per design 55 Sft 1255 69025

GYPSUM PARTITIONING:- Providing and fixing partition upto ceiling height

consisting of G.I. frame and required board, including providing and

fixing of frame work made of special section power pressed/ roll form

G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive),

consisting of floor and ceiling channel 50mm wide having equal flanges

of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of

610 mm centre to centre with dash fastener of 12.5 mm dia meter 50

mm length or suitable anchor fastener or metal screws with nylon plugs

and the studs 48 mm wide having one flange of 34 mm and other

flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor

and ceiling channel and placed at a spacing of 610 mm centre to centre by

6 mm dia bolts and nuts, including fixing of studs along both ends of partition

fixed flush to wall with suitable anchor fastener or metal screws with

nylon plugs at spacing of 450 mm centre to centre, and fixing of boards

to both side of frame work by 25 mm long dry wall screws on studs, floor

and ceiling channels at the spacing of 300 mm centre to centre.

The boards are to be fixed to the frame work with joints staggered to

avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm

thick having two flanges of 9.5 mm each) to be provided at the

horizontal joints of two boards, fixed to the studs using metal to metal

flat head screws, including jointing and finishing to a flush finish with

recommended jointing compound, jointing tape, angle beads at corners

(25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer

suitable for board as per manufacture's specification and direction of

engineer in charge all complete.

9.105.1 75 mm overall thickness partition with 12.5 mm thick double skin fire rated

Glass Reinforced Gypsum (GRG)

plaster board conforming to IS: 2095: 80 sq m 2,131.10 170488

Add labour cess @0.973 as per CPWD circular 20,22,994.59

Digitally signed by AMIT

Add CPWD cost index @103 on DSR civil 2023 20,83,684.43

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

TOTAL AMOUNT TOTAL AMOUNT

TOTAL AMOUNT TOTAL AMOUNT

DESCRIPTION UNIT QUANTITY RATE

2022 DSR (INR) NON-DSR (INR)

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point

with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable

1.10 in surface / recessed medium class PVC conduit, with modular switch,

A.1 modular plate, suitable GI box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point

(without independent switch etc.) with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed PVC conduit,

A.2 and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single

core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper

conductor single core cable in surface/ recessed medium class PVC

conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper

conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing

1.24 modular plate & switch box including connections but excluding modular

plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 60 122.00 7320.00

1.24.5 6 pin 15/16 amp socket outlet Each 60 197.00 11820.00

Digitally signed by AMIT

Supplying and fixing modular blanking plate on the existing modular

plate & switch box excluding modular plate as required.

Supplying and fixing following size/module, GI box along with Modular

base & cover plate on existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following

1.14 sizes of FR PVC insulated copper conductor, single core cable in surface/

recessed medium class PVC conduit as required

1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 150 233.00 34950.00

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 500 275.00 137500.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 50 439.00 21950.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 50 1365.00 68250.00

Supplying and making end termination with brass compression

gland and aluminium lugs for following size of PVC insulated and PVC

sheathed / XLPE aluminium conductor cable of 1.1 KV grade as

Supply of following XPLE armourned 1.1 KV grade conforming to

I.S.7098/1554Aluminium Conductor Cables :

Digitally signed by AMIT

MR Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium

C.2 conductor armoured cable of 1.1 KV grade conforming to IS:7098 part-1 /

IS:1554 part-1 respectively & ISI marked.

(b) 3.5 C x 95 Sqmm XLPE cable RM 30 864.00 25920.00

(e) 3.5 C x 35 Sqmm XLPE cable RM 30 378.00 11340.00

Supply of following sizes of copper cables -PVC sheathed PVC/XLPE

C.3 MR insulated Copper conductor armoured cable of 1.1 KV grade

conforming to IS:7098 part-1 / IS:1554 part-1 respectively & ISI marked.

(a) 4 C x 16 Sqmm XLPE copper cable RM 50 1446.00 72300.00

(b) 4 C x 25 Sqmm XLPE copper cable RM 35 2253.00 78855.00

Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required.

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in

D.2 the existing MCB DB complete with connections, testing and

commissioning etc. as required.

2.10.1 Single pole Each 32 256.00 8192.00

Supplying and fixing following rating, four pole, 415 volts, isolator in the

2.13 existing MCB DB complete with connections, testing and commissioning etc.

Supplying and fixing following way, horizontal type three pole and

neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess,

2.4 complete with tinned copper bus bar, neutral bus bar, earth bar, din

D.4 bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/ RCCB/ Isolator)

MR 12 way (4 + 36), Double door Each 2 9081.00 18162.00

Digitally signed by AMIT

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper

conductor PE insulated, shielded with fine tinned copper braid and

protected with PVC sheath in the exisitng surface/recessed steel/

PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with

1.21 accessories in surface/ recess including cutting the wall and making good

the same incase of recessed conduit as required

Supplying and Installation of following size perforated of painting with

powder coating M.S. cable trays of perforation of not more than

E.13 4.1 17.5% in convinient sections, joined with connectors suspended from

the cieling with MS suspenders including bolts and nuts painting suspenders

etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 15 1137.00 17055.00

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick

including accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe of 2.7 metre long etc.

with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess

for connections etc. As required.

Supply, Installation, Testing and Commissiong of 10 KVA True Online Double

Conversion UPS 3Phase Input - 3Phase Output in IGBT Based Rectifier and

IGBT Based Inverter Batteries:12 V, SMF Amararaja/Exide with minimum VAH

capacity of 15600 suitable for 30 minutes backup with each ups Along with

Accessories Rack, Interlinks, SFU, Parallel Kit, DC Cable Upto 5 Meters Nos 1 365000.00 365000.00

complete in all respect as per the directions of the engineer in charge. UPS

should have availability of Input /Output isolator, Inbuilt manual bypass along

with phase sequence corrector. UPS Efficiency shall not be less than 94% from

25% to 100% Load

Total of Electrical items 774616.00 571577.00

Add GST factor @1.0633 on DSR items 823649.1928

Digitally signed by AMIT

Add CPWD labour cess factor @0.973 801410.6646

Total Amount 801410.6646 571577.00

Total Amount 801410.6646 571577.00

Digitally signed by AMIT

1.0 VRF/VRV OUTDOOR UNIT Unit Quantity Rate DSR Amount

Supply, Installation, Testing & Commissioning of Modular type

Variable Refrigerant Flow/Variable Refrigerant Volume air cooled

Outdoor units suitable for cooling/heating having 100% hermetically

sealed inverter type twin Rotary/Scroll Compressor(s), minimum two

compressors (with individual separate PCB) for above 14HP modules,

microprocessor based Controller, top discharge type condensing unit(s),

with R-410-A Refrigerant or equivalent, vibration Isolators with suitable

foundation etc. complete as required. To have better efficiency

condenser fan shall be capable to operate at different speed with

respect to load. The unit shall deliver the rated capacity and in

confirmation as per IS 18728:2024 and CPWD Specifications and work

even at 50°C ambient temperature without tripping. The system shall

7.3 be able to deliver 100% of the rated capacity upto 39 Degree

Celcius.The unit shall be suitable to work on 400V +/- 10%, 3 Phase,

50Hz AC power supply and BMS compatible. The unit shall be filled

with first charge of the refrigerant and ready for use as required. The

condenser should be coated with a hydrophilic film to prevent water

accumulation on the surface of the heat exchanger, enhance water

dispersion, and reduce the risk of degradation, thereby improving

overall performance and durability. The Indian Seasonal Energy

Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation

and Sustainable Building Code (ECSBC) 2024 as below and complete

as per CPWD specification, connections, inter connections etc. as

required. (For capacity <40 kWr ISEER 7.4, Capacity > 40 and <70 ISEER

7.5, Capacity > 70 ISEER 7.6 for Super ECSBC Building)

2.0 INDOOR UNIT

Digitally signed by AMIT

Supply, Installation, Testing and Commissioning of following minimum

capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with

synthetic washable media pre- filter, fan section with low noise fan /

dynamically balanced blower, multispeed motor, coil section with DX

Copper coil, electronic expansion valve, outer cabinet, drain pump, grill,

necessary supports, vibration Isolation, Corded remote control etc.,

suitable for operation on single phase 230 V ± 10%, 50Hz AC supply,

complete, as required. The Indoor units must shut down upon receiving

a singal from the BMS System/Fire Signals. The system shall be capable

to adjust air flow as per room requirement in auto mode. The cooling

capacity of indoor unit will be at air inlet conditions of 27 Degree C

DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Supply, Installation, Testing and Commissioning of following minimum

capacity High wall type Indoor unit equipped with and comfort

washable synthetic media pre-filter, fan section with low noise

fan/dynamically balanced blower, multispeed motor, coil section with DX

copper coil, electronic expansion valve, outer cabinet, cord less remote

control, drain pan, necessary accessories etc., suitable for operation on 230

V ± 10%, 50 Hz, single phase AC supply, complete as required. The Indoor

units must shut down upon receiving a singal from the BMS System/Fire

Singnals. The system shall be capable to adjust air flow as per room

requirement automatically. The cooling capacity of indoor unit will be at

air inlet conditions of 27 Degree C DB and 19 Degree C WB

temperature. (Make will be same as of Outdoor)

REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation

and Nitrogen testing of following nominal sizes of soft/hard drawn

copper refrigerant piping for VRV/VRF system, complete with fittings,

with suitable adjustable ring type hanger supports, jointing/brazing

including accessories, insulated with XPLE Class-O tubular

insulation/with Class-O closed cell elastometric nitrile rubber tubular

sleeves sections of 19 mm thick insulation as given below for Suction

and Liquid lines, all accessories as per specifications etc. as required :

3.1 7.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 25.00 256.00 6,400.00

3.2 7.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 20.00 346.00 6,920.00

3.3 7.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 10.00 487.00 4,870.00

Digitally signed by AMIT

3.4 7.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 25.00 615.00 15,375.00

3.5 7.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 15.00 739.00 11,085.00

3.6 7.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 20.00 904.00 18,080.00

3.7 7.14.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 10.00 1,068.00 10,680.00

3.8 7.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 30.00 1,157.00 34,710.00

3.9 7.14.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 20.00 1,222.00 24,440.00

3.10 7.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 20.00 1,286.00 25,720.00

3.11 7.14.11 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 30.00 1,322.00 39,660.00

3.12 7.14.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 20.00 1,368.00 27,360.00

3.14 7.13.2 Outdoor Multi Units Each 1 8098 8,098.00

Supplying and installing of following size of perforated hot dip

galvanized G.I cable tray with perforations not more than 17.5%, in

4 MR convenient sections, joined with connectors, suspended from ceiling

with G.I suspenders including bolts and nuts, etc. for carrying

refrigerant pipe in outdoor application as required.

4.1 450 mm width x 62.5 mm depth x 2 mm thickness Rmt 5.00 1,139.00 5,695.00

4.2 225mm width x 50 mm depth x 1.6 mm thickness Rmt 10.00 729.00 7,290.00

5 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe, complete with

fittings, supports,U trap arrangement,Clean Plug with 6mm nitrile insulation

and accessories as per specifications, drawings.

6 MR Supply & Fixing IP55 Base Outdoor MCB Box with in 1 Nos 65 amp RCCB Nos 1 14650 14,650.00

Supply and Fixing MS Base Frame for VRV Outdoor Stand as per requirement

Add GST factor @1.0633 on DSR items 1768567.751

Add CPWD labour cess factor @0.973 1720816.421

Total Amount 1720816.421 61165.00

Total Amount 1720816.421 61165.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - DATA and VOICE WORKS

S NO Description UOM Qty Rate DSR Amount NDSR Amount

A. UTP Components for Data

Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper

conductors for Connectivity of Hub room to End Point.High Speed

Gigabit Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded LSZH

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable

termination at Rack Side. Keystone Unshielded Outlet, 180DG C6, Blue

Supply , Installtion , Testing and Comissioning of I/O port for CAT6 cable

3 MR termination at Rack Side end Redantant . Keystone Unshielded Outlet, Nos. 40 359.00 14360

180DG C6, Yellow

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr

(7 feet) for information outlet (I/O) to end user Redantant device

connectivity.High Speed Gigabit 24AWG U/UTP Patch Cord Yellow, LSZH,

C6, 2M (Yellow)

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 2 Mtr

(7 feet) for information outlet (I/O) to Rack End Redantant device

connectivity.High Speed Gigabit 24AWG U/UTP Patch Cord Yellow, LSZH,

C6, 2M (Yellow)

Supply , Installtion , Testing and Comissioning of 24 port Loaded Angled

6 MR Staggred Jack Panel for CAT6 cable termination at rack end. Data Nos. 4 6500.00 26000

Active Redandant

8 MR SITC of 24U Rack Each 1 34,500.00 34500

Supply instllation testing and commissioning of Access Switch of 24 x 1G POE+, 4 x

SFP+ , 370W PoE, Switching Capacity of switch is of 176 Gbps having Forwarding

9 MR performance (64-byte packet size): 130 Mpps, Secure Shell (SSH), as per approved

B 200 Pair MDF Box

1 MR 200 Pair MDF Box with mounting Frame Nos. 1 11666.00 11666

Digitally signed by AMIT

2 MR 10 Pair Krone Module Nos. 5 900.00 4500

3 MR 25 Pair Riser Cable Mtr. 15 750.00 11250

GRAND TOTAL (A+B) 119700.00 322994.33

GRAND TOTAL (A+B) 119700.00 322994.33

Add GST factor @1.0633 on DSR items 127277.01

Add CPWD labour cess factor @0.973 123840.53

Total Amount 123840.53 322994.33

Total Amount 123840.53 322994.33

Digitally signed by AMIT

SCHEDULE OF QUANTITIES: FIRE PIPING, HYDRANTS, SPRINKLERS AND ACCESSORIES

S TOTAL TOTAL

2022/ DESCRIPTION QTY UNIT RATE

No AMOUNT AMOUNT

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL

Listed) of stainless steel complete with 15 NPT on reducer thread with maximum

working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet)

25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread

1 with reducer, nipple, 2 side brackets, center bracket, stockbar of

following sizes complete as required.

Providing and fixing ISI Marked of approved make Fire Extinguishers

2 complete with all accessories as per

manufacturer's specifications.

a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). 2 NOS 12070.00 24140.00

Mechanical Foam gas cartridge type. 9 Kg capacity

ABC dry powder stored pressure type 6 kg capacity

Add CPWD labour cess factor @0.973 45723.745

Total Amount 45723.745 38494.00

Total Amount 45723.745 38494.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - CCTV

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

S NO DSR/ MR DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

Supply, Installation, Testing & Commissioning of 4MP IR IP H.265 Vandal

Proof Dome camera with 2.8 to 12mm Motorised Lens,Smart IR, up to

30M IR distance,Up to 120 dB WDR (Wide Dynamic Range),3D DNR

(Digital Noise Reduction),H.265+, H.265, H.264, MJPEG,Corridor mode,

Triple streams,3-Axis, IP67, IK10 Vandal Resistant,Colour: 0.005Lux (F1.4,

AGC ON), 0 Lux with IR,Video Compression H.265+, H.265, H.264,

MJPEG,Behavior Detection Intrusion,

Supply, installation testing and commissioning of Network Video

recorder Linux based to manage and control all the cameras from

control room. Software shall support maximum 16 channel with

2 MR joystick controller. 256Mbps Bit Rate Input Max(up to 32-ch IP video), 2 Nos 1 34500.00 34500.00

SATA Interfaces, alarm I/O: 16/4, 1.5U case,19" with 1x4TB i.e. 4TB HDD inside

Supply Installation Testing & Commissioning of 32 inch Full HD LED monitor

including wall mount brackets/ clamps/ desk mounting stand.

SITC of HDMI cables 10 meters M2M etc all compelte.

Total : A - CCTV 90400.00

Digitally signed by AMIT

Sno. Item Specifications Unit Qty Rate Amount

GM Table Supplying and placing in position of main table as per photograph/drawing .The table shall be made

out of 25mm thick pre -laminated particle board of approved shade. The working and non working

edges shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be

supported with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x

40mm. The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc

edge banding. The table shall be provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x

1 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & Nos. 1.00 52,000 52,000.00

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board.

Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site

requirement.Main Table Dimension (L)2100mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)1800mm X (D) 450mm X (H) 675mm

GM High Back Supplying and placing in position of 360 degrees revolving high back chair. The chair of Size

Chair :-(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

with leatheritte and cut foam. The chrome plated loop armrest with padded upholstery is provided for

extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke

of 10.0+/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35

(+/ 2kg /m3) Dimensions The backrest has a foam of 28kg/m3.

GM Visitor Back Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X

Chair (H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium Leatherette,

Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever,

3 Base:Cantilever Frame, Base Type:Cantilever, Maximum Seating Height:19".The Seat & back are made Nos. 3.00 8,500 25,500.00

up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has

foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

3 seater sofa Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the soft

GM Cabin/ cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour Family:as

Reception per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech

4 solid wood have used for framing construction of sofa .The seat cushion is made of multi layered Nos. 2.00 36,000 72,000.00

foam of density 32-35 kg/m3. The seating cushion have 2.75 &

1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength .

The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

Dimension(L)1390mm X (D)750mm X (H)710mm

GM Cabin/ Supplying, and placing in position of Cofee/ Corner Table as per approved design Dimension(L)450mm

5 Reception X (D)450mm X (H)450mm Nos. 2.00 8,000 16,000.00

DGM Table Supplying and placing in position of main table as per photograph/drawing .The table shall be made

out of 25mm thick pre -laminated particle board of approved shade. The working and non working

edges shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be

supported with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x

6 40mm. The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc Nos. 2.00 44600.00 89,200.00

edge banding. The table shall be provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x

675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter &

Digitally signed by AMIT

DGM High Back Supplying and placing in position of 360 degrees revolving high back chair . The chair of Size

Chair :-(W)590mm X (D)505mm X (H)1180mm - 1280mm. The chair shall be ergonomically design contour

lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

with leatheritte and cut foam. The chrome plated loop armrest with padded upholstery is provided for

7 extra comfort. The chair shall be provided with pneumatic height adjustment which shall have stroke Nos. 2.00 16500.00 33,000.00

+/- 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30- 35 (+/ 2kg

/m3) Dimensions The backrest has a foam of 28kg/m3.

DGM Visitor Supplying and placing in position of medium back cantilever chair of size: (W)610mm X (D)505mm X

Back Chair (H)990mm.A contemporary design with an all black finish, . Material & subtype:Premium Leatherette,

Colour & Colour Family:Black, Dimension(W)610mm X (D)505mm X (H)990mm, Back Type:Cantilever,

8 Base:Cantilever Frame, Base Type:Cantilever, Maximum Seating Height:19".The Seat & back are made Nos. 4.00 14500.00 58,000.00

up of 12mm thk hot pressed plywood upholstered with PVC with polyurethane foam, chair seat has

foam of density 32-35 kg/m3. The backrest has a foam of 28kg/m3.

2 seater sofa Supplying, and placing in position of sofa with premium Leatherette upholstery adds class to the soft

cushioned backrest and seating. Material & subtype:Premium Leatherette, Colour & Colour Family:as

per requirement, Seating Height:16.14"

,Legs:Stainless Steel, Finish:Matte, Size:Compact, Style:Modern, Texture:Two Tone. steam beech

9 solid wood have used for framing construction of sofa .The seat cushion is made of multi layered Nos. 3.00 25500.00 76,500.00

foam of density 32-35 kg/m3. The seating cushion have 2.75 &

1.75 inches of elastic webbing. The thread used is nylon bonded to provide lasting stitch strength .

The backrest has a foam of 28kg/m3 with polyster polyfill outer layer of 200 gsm. 2 seater

Dimension(L)1390mm X (D)750mm X (H)710mm

DGM Cabin Supplying, and placing in position of Cofee/ Corner Table as per approved design Dimension(L)450mm

10 Corner/ Cofee X (D)450mm X (H)450mm Nos. 2.00 10500.00 21,000.00

AGM Table Supplying and placing in position of main table as per photograph/drawing .The table shall be made

out of 25mm thick pre -laminated particle board of approved shade. The working and non working

edges shall be finished with machine pressed with 2mm PVC egdge banding. The table top shall be

supported with MS powder coated "C" shape leg of size 50mm x 50mm with connectors of size 40mm x

40mm. The front modesty are made out of 18mm thick prelaminated particle board with 2mm thk pvc

edge banding. The table shall be provisioned with Side unit of overall size: 1800mm(L) x 450mm(D) x

11 675mm(H) . Side storage having a provision for three equal drawer unit and two openable shutter & Nos. 4.00 38,790 1,55,160.00

one open storage with shelf in it. The Side unit top shall be made out of 18mm thick pre laminated

particle board and rest all storage to be made out of 18mm thick pre laminated particle board.

Provision of Junction box, wire raceway and 6 module fliptop box for wire passing or as per site

requirement. Main Table Dimension (L)1800mm X (D) 900mm X (H)750mm overall Side Runer

Dimension (L)1800mm X (D) 450mm X (H) 675mm

AGM Chair Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof plywood

and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS grade - 303)

upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be provided with self

tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/-

12 0.3 cm .The black .The pneumatic height adjustment shall have adjustment stroke of 100 mm and Nos. 4.00 14,500 58,000.00

shall be operated at 30kgs extension force.The Seat & back are made up of 12mm thk hot pressed

plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.

The backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Digitally signed by AMIT

Conference Supplying and placing in position of conference table of required size as per image/drawing. The work

Table surface top should be of thickness 42mm top prelaminated particle board with 2mm thick PVC edge

banding. The side panel are made up of 36mm thick prelaminated particle & modesty panel are made

13 out of 25mm thick prelaminated particle board with 2mm thick PVC edge banding. The wire carrier Nos. 1.00 77,500 77,500.00

should be made from 0.6mm thick CRCA & powder coated 40-50 microns. Also having a provision of

6 module flip top box & metal raceway for wire flow.

Confrence high Supplying and placing in position of 360 degrees revolving high back chair of size: 660mm (L) x

back Chair 490mm(D) x 1315mm(H). The seat cushion to be upholstered on 10-12mm thick water proof plywood

and moulded foam. The seat to be made with 12 mm thick hot pressed BWR plywood (IS grade - 303)

upholsetered with Polyurethane foam and mesh fabric over it. The chair shall be provided with self

tension single locking mechanism and pneumatic height adjustment which shall have stroke of 10.0 +/-

14 0.3 cm .The black .The pneumatic height adjustment shall have adjustment stroke of 100 mm and Nos. 2.00 14,500 29,000.00

shall be operated at 30kgs extension force.The Seat & back are made up of 12mm thk hot pressed

plywood upholstered with PVC with polyurethane foam, chair seat has foam of density 32-35 kg/m3.

The backrest has a foam of 28kg/m3. adjustable arm rest and head rest

Medium Back Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size

chair AGN :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

Cabin lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

15 with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which Nos. 8.00 12,450 99,600.00

shall have stroke of 10.0 +/-

0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg

/m3) The backrest has a foam of 28kg/m3.

Modular Dimesnion: 1500mm(L) x 1500mm(L) x 600mm(D) x 1200mm(H) Modular Workstation With Side

Workstation Top with 3 drawer Pedestal Size 1500W x 600D x 750/1200H.Partition NI-60mm Partition Ht.

1200mm, Double Raceway systems Skirting label and below the table top . lower tile both side

laminated and upper tile inside side fabric, White

16 Board and white Tinted Glass . With Side Top Size 900W x 400D x 750H 25mm thick Gabel end Nos. 17.00 31,500 5,35,500.00

18mm thick MDF board., and 3Drawer top supported Pedestal unit Size 400W x 400D x 725H

made in 18mm thick..Complete Made in MDF Board.. Laminate 1- Frosty White, Laminate2 For drawer

Facia-Honkong Blue, Fabric-F 161 Dolphin Blue, Powder Coating- Munshel Gray. and White Tinted

Linear Dimension: 1200mm(L) X 600mm(D) x 1050mm(H) Supplying, and placing in position of linear

Workstation workstation as per Image.The worktop made out of 25mm thk. Prelam Particle board with 2 mm thk

PVC edge banding.The Table top supported on Mild Steel of size 50mm x50mm Slanted Leg and 50mm

x 25mm Horizontal connectors with Powder coting of 50 Micron.Middle Leg :- 0.8 mm thk Metal panel

fixed on both side of the "T" leg for Vertical wire carrying purpose.(Sharing Workstation). 0.8 mm thk

Single/Double metal powder coated raceway with Powder coting of 50 Micron below top for

wiring.Vertical wire carrying pole with powder coating 50 micron below top for wiring( Non- sharing

workstation ). Also having a provision of ms perfoated sheet hanging modesty. provision of glass

divider rest on the "D" brackets on the table top between opposite seatings. All working or non

working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt

glue at hot temperature. Provision of pullout PVC keyboard tray and CPU trolley for each seating.

Also a provision of Pedestal Unit (size:- L-400mm x D-450mm x H-600mm) with a combination of

2 drawer & one filing drawer. The pedestal storage unit shall be made of 18 mm thick prelaminated

Particle board with provision of handles & Locking arrangement

Digitally signed by AMIT

Medium Back Supplying and placing in position of 360 degrees revolving medium back chair . The Craze chair of Size

chair :-(W)590mm X (D)505mm X (H)1005mm - 1115mm. The chair shall be ergonomically design contour

Workstation/ lumbar back design made of 12mm thick BWR plywood (IS Grade - 303 for seat and back) upholstered

Reception/ with leatheritte and cut foam. The chair shall be provided with pneumatic height adjustment which

18 Confrence shall have stroke of 10.0 +/- Nos. 35.00 12,450 4,35,750.00

room 0.3 cm . Five star chrome base with nylon castors . Chair seat has foam of density 30-35 (+/- 2kg

/m3) The backrest has a foam of 28kg/m3.

Pantry Table Providing & Installation of Pantry table of size 1.8m x 0.75m x 1.05m (ht) made out of 19mm thk.

Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

19 Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above Nos. 1.00 26,500 26,500.00

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Reception Providing & Installation of Reception table of size 1.2m x 0.75m x .9 m (ht) made out of 19mm thk.

Table Commercial Board finished in Recon veneer and DU Pont Coreanof approved shade as per design. The

20 Recon surfaces to be white Duco painted. A glass top od width 0.2m on SS pegs to be provided above Nos. 1.00 24,500 24,500.00

table. One (1) number Drawer pedestal with 3 drawers to be provided under the table.

Pantry chairs Providing & Installation of Pantry chairs of required dimension and as per instruction of EIC 10.00 4,500

Openable The storage top 25 mm thick, shutter and side panels are made of 18mm thick and back panel is made

Shutter storage of 09mm thick MDF of approved shade. All the edges of storage surface shall be provided with machine

22 pressed imported PVC lipping glued with hot melt EVA glue free from any VOC with free groove handle

and suitable lock. All exposed area PVC edge lipping

Total Amount 24,29,210.00

Total Amount 24,29,210.00

Digitally signed by AMIT

Sl. No. Description Unit Qty. Rate Amount

LED Down lighter (COB Type) (System lumen efficacy ≥ 105 < 120 lm/Watt ) Supplying of LED

Recessed/ surface Down lighter (Round/ square/ Rectangular) COB Type of following body

material and construction as per IS : 10322 with driver as per the requirement with Driver efficiency

>85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -15 deg to

40 deg centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection

,THD < 10% , P. F.≥0.95, IP20, CRI >80 , UGR (Unified Glare Rating) < 19, Flicker free (flicker should be

below 5%), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours with 70%

of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K / 6000°K / 6500°K

(As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption

4221 should not more than the specified rating and Fixture shall be confirming to relevant BIS Nos 40 566.00 22640

standards and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing Complete in all respect i/c connections with 1.5 sq

mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy ≥105 and <120 lm/Watt output . LM79 &

LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be

submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement.

(Thermal management: heat sink of aluminium housing such that LED junction temperature

shall not rise above 90°C) Powder coated die cast /Extruded aluminium Body including trim with

Aluminium Reflector 12 -15 watt

LED Panel light 2x2 ft., (System lumen efficacy >135 lm/Watt) Supplying of Panel light 2x2 ft., of

following body material and construction as per IS : 10322 with driver as per the requirement with

Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp

range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open

circuit protection,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare Rating) < 19, Flicker free,

(flicker should be below 5 %), life time (LED,Driver & electrical circuitary), of minimum 50000

Burning Hours with , 70% of initial Lumen maintained till life ends ,CCT 3000°K / 4000°K / 5700°K

/6000°K/6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching) <3, Maximum

4258 power consumption should not more than the specified rating and Fixture shall be of relevant BIS Nos 35 2700.00 94500

standard and trade mark certificate (T.C.). Manufactures Word Mark/ Name Engraved/

Embossing/ Screen printing on housing. complete in all respect i/c connections with 1.5 sq mm

FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy >135 lm/Watt output . LM79 & LM80 Test

report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted.

Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminium housing such that LED junction temperature shall not rise

above 90°C). Powder coated die cast /Extruded aluminium Body (Thickness > 1.20 mm)

Total of Electrical items 117140.00

Digitally signed by AMIT