Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L-1₹18.6 LAccepted-AOC GOKUL APARTMENT PANJABIPARA DISTT JALPAIGURI SILIGURI 734401 WB | DARJEELING | WEST BENGAL | 734401 | L-1 | Accepted-AOC Being L 1 | |
| 2 | L-2₹19.6 L+₹38,279.09 (1.99%)Rejected-Finance NH 31 GAIRKATA PO SAKOAJHORA DIST JALPAIGURI W B PIN 735212 | JALPAIGURI | WEST BENGAL | 735212 | L-2 | Rejected-Finance Being L 2 | |
| 3 | L-3₹22.4 L+₹3.1 L (16.4%)Rejected-Finance 96 SECTOR 16 A CHANDIGARH 160015 | CHANDIGARH | CHANDIGARH | 160015 | L-3 | Rejected-Finance Being L 3 |
Tender Value
₹30 L
EMD Value
₹60,000
Closing Date
17 Dec 2020, 6:00 pmClosed
GE North Binnaguri
Post Binnaguri Dist Jalpaiguri West Bengal
REPAIR AND MAINTENANCE OF WOODEN AND STEEL FURNITURES AND SOFA SETS INCLUDING PAINTING POLISHING AT BINNAGURI MIL STATION UNDER GE NORTH BINNAGURI
2020_MES_397622_1
NIT No. 8701/33/2020-2021/ 03 / E8
Open Tender
Miscellaneous Works
Item Rate
180 days
BINNAGURI
Class D Category ai
8 documents required · 8 mandatory
₹500
Yes
GE North Binnaguri
₹60,000
Yes
28 Jan 2021
24 Nov 2020
19 Dec 2020
24 Nov 2020
17 Dec 2020
5 Dec 2020
Amount
WOODEN FURNITURE Repairs to Bed Hard Ply top for the following :- Removing old unserviceable fitting and fixture of Bed Hard plywood top such as Head board, Foot Board, Long Rail, sttiffner, plywood , MS clamps etc and supply and refixing with new items of Best quality 2nd Class HW (Hollock/Tita Champa/SAL) and minor repair applying French Polish glossy finished to match with existing surface complete all as specified and shown on drawing. (Drawing No: 213/246)
Top Plywood 12mm thick, 7 No ply, ISI marked conforming to IS: 303-1989. (Make-Green Ply/Kit Ply,Century/Bhutan Board)
Long rails
Short rails made from old long rail obtain from taking down
Stiffeners in centre of both leg rail 40 mm x 30 mm
Veneered plywood Gde-1 quality (BWR resin) 3mm thick (one side teak face decorative type for Head Board, ISI marked (Make-Green Ply/Kit Ply,Century/Bhutan Board)
Veneered plywood Gde-1 quality (BWR resin) 3mm thick (one side teak face decorative type for Foot Board, ISI marked (Make-Green Ply/Kit Ply,Century/Bhutan Board)
Mild Steel clamps old refixing in new position with new screws.
Mild Steel clamps new of existing size and shape including appying two coat of synthetic enamel paint (1st quality) over a coat of zinc chrome red oxide primer.
Repairs to Chair Writing for the following :- Removing old unserviceable fitting and fixture of Chair Writing without disturbing to the other parts such as legs,rails, stiffiners, Hand rest etc and supply and fixing with new items of Best quality 1st Class HW (Teak)) and minor repair applying French Polishone or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD-20(M)/ 280)
Rear legs 1st class hardwood (TeaK)
Front legs. 1st class hardwood (TeaK)
Front /rear rails of seat frame .1st class hardwood (TeaK)
Right/ left side rails of seat frame . 1st class hardwood (TeaK)
Stiffener.bottom 1st class hardwood (TeaK)
Stiffener back rest 1st class hardwood (TeaK)
Arm rest. 1st class hardwood (TeaK)
Taking out unserviceable plastic cane from seat frame of Chair writing and Supply and fixed for weaving the seat of Chair in Godrej pattern with new 2 mm wide half round 0.40mm thickness and 4mm for border approved quality complete all as specified and shown in drawing. (Drawing No. FD-20 (M)/280)
Repairs to Chair dining for the following :- Removing old unserviceable fitting and fixture of Chair dining without disturbing to the other parts such as legs,rails, stiffiners etc and supply and fixing with new items of Best quality 1 st class hardwood (Teak) and minor repair applying French Polishone or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 16(M)/228/279)
Rear legs 1st class hardwood (TeaK)
Front legs.1st class hardwood (TeaK)
Front /Back/ side rails of seat frame . 1st class hardwood (TeaK)
Leg Stiffener 1st class hardwood (TeaK)
Back batten 1st class hardwood (TeaK)
Taking out unserviceable plastic cane from seat frame of Chair dining and Supply and fixed for weaving the seat of Chair in Godrej pattern with new 2 mm wide half round 0.40mm thickness and 4mm for border approved quality complete all as specified and shown in drawing. (Drawing No. FD-16(M)/228/279)
Repairs to Table 900 mm x 900 mm x 760 mm (Table 3'x3') for the following :- Removing old u/s fitting /Fixture of Table 900 mm x 900 mm disturbing to the other parts such as legs,rails, top, stiffiners etc and supply and fixing with new items of Best quality 1st Class HW (Teak) and minor repair applying French Polishone or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : 88(M) / 201)
Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5mm thick timber beading around the edging.
Legs 1st class hardwood (TeaK)
Side rails 1st class hardwood (TeaK)
Stiffeners in centre of both leg rail 40 mm x 30 mm
Triangle HW support of size 100 mm x100 mm for Legs with rails
Repairs to Table 900 mm x 600 mm x 760 mm (Table 3'x2') with/without Drawer for the following :- Removing old unserviceable fitting and fixture of Table 3' x 2' with and witout drawer without disturbing to the other parts such as legs,rails, top,stiffiners, Drawer etc and supply and fixing with new items of Best quality 1st class HW (Teak) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : 41(M)/42(M)/55(M)/231/ 283/284
Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5mm thick timber beading around the edging.
Drawer as per existing shape and size made out of 1st class hardwood (Teak) complete all as specified and as directed.
Legs 1st class hardwood (TeaK)
Long rail 1st class hardwood (TeaK)
Side rails 1st class hardwood (TeaK)
Stiffeners 1st class hardwood (TeaK)
25 mm dia chroumium plated Knob with brass nuts and bolts
Repairs to Teapoy for the following :- Removing old unserviceable fitting and fixture of Teapoy without disturbing to the other parts such as legs,rails, top,stiffiners etc and supply and fixing with new items of Best quality 1 st class hardwood well seasoned (Teak) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : 34(M)/278)
Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class harwood (teak) beading around the edging.
Legs 1st class hardwood (TeaK)
Long rails 1st class hardwood (TeaK)
Side rails 1st class hardwood (TeaK)
Repairs to Peg Table for the following :- Removing old unserviceable fitting and fixture of Pag table without disturbing to the other parts such as legs,rails, top,stiffiners etc and supply and fixing with new items of Best quality 1 st Class Hard wood wellseasoned (TEAK) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 25(M)/236/277/384)
Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1 st class hardwood (teak) beading around the edging.
Long rails 1st class hardwood (TeaK)
Short rails made from old long rail obtain from taking down
Legs 1st class hardwood (TeaK)
Repairs to Table Centre for the following :- Removing old unserviceable fitting and fixture of Table centre without disturbing to the other parts such as legs,rails, top,stiffiners etc and supply and fixing with new items of Best quality 1 st class hardwood (Teak) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 29(M)/235/ 274)
Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class haedwood beading around the edging.
Legs 1st class hardwood (TeaK)
Long rails 1st class hardwood (TeaK)
Side rails 1st class hardwood (TeaK)
Repairs to Table dining 8 person for the following :- Removing old unserviceable fitting and fixture of Table Dining 6 Person without disturbing to the other parts such as legs,rails, top, stiffiners etc and supply and fixing with new items of Best quality 1st class hardwood (Teak) and minor repair applying of French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : 30(M)/273)
Top of 18 mm thick particle board conforming to IS-3087-2005 with 1 mm thick plastic laminated sheet teak face shead on top using approved adhesive including 4mm thick 1st class hardwood (Teak) beading around the edging.
Legs 1st class hardwood (TeaK)
Long rail 1st class hardwood (TeaK)
Side rails 1st class hardwood (TeaK)
Repairs to Table dining 6 person for the following :- Removing old unserviceable fitting and fixture of Table Dining 6 Person without disturbing to the other parts such as legs,rails, top, stiffiners etc and supply and fixing with new items of Best quality 1st class hardwood (Teak) and minor repair applying of French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD :30(M)/273 )
Top of 18 mm thick particle board conforming to IS-3087-2005 with 1 mm thick plastic laminated sheet teak face shead on top using approved adhesive including 4mm thick 1st class hardwood (Teak) beading around the edging.
Legs 1st class hardwood (TeaK)
Long rail 1st class hardwood (TeaK)
Side rails 1st class hardwood (TeaK)
Repairs to Chair wooden bottom without arms for the following :- Removing old unserviceable fitting and fixture of Chair Writing without disturbing to the other parts such as legs,rails, stiffiners, Hand rest etc and supply and fixing with new items of Best quality 1st Class HW (Teak)) and minor repair applying French Polishone or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD-56(M)/ 285)
Rear legs 1st class hardwood (TeaK)
Front legs. 1st class hardwood (TeaK)
Front /rear rails of seat frame .1st class hardwood (TeaK)
Right/ left side rails of seat frame . 1st class hardwood (TeaK)
Stiffener.bottom 1st class hardwood (TeaK)
Stiffener back rest 1st class hardwood (TeaK)
Seat Plywood (Make-Green Ply/Kit Ply,Century/Bhutan Board) 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989
Repairs to Chair Easy for the following :- Removing old unserviceable fitting and fixture of Chair Easy without disturbing to the other parts such as legs,rails, stiffiners, Hand rest etc and supply and fixing with new items of Best quality 1st Class HW (Teak) and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 17)M)/ 229)
Rear legs 1st class hardwood (TeaK)
Front legs. 1st class hardwood (TeaK)
Top rails .1st class hardwood (TeaK)
Side Top rails (Left/Right) .1st class hardwood (TeaK)
Rear Top rails (Left/Right) .1st class hardwood (TeaK)
Side bottom rails (Left/Right) .1st class hardwood (TeaK)
Front/ Rear bottom rails.1st class hardwood (TeaK)
Taking out unserviceable plastic cane from seat frame of Chair Easy and Supply and fixed for weaving the seat of Chair in Godrej pattern with new 2 mm wide half round 0.40mm thickness and 4mm for border approved quality complete all as specified and shown in drawing. (Drawing No. FD-20 (M)/280)
Arm rest. 1st class hardwood (TeaK)
Repairs to Table Writing for the following :- Removing old unserviceable fitting and fixture of Table Writing without disturbing to the other parts such as legs,rails, top,stiffiners,Drawer etc and supply and fixing with new items of Best quality 1st class hardwood well seasoned (Teak) and 4mm thick wooden beading whereever required and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 33(M)/249/275 )
Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging.
Sides of size 600mm x 560mm with 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging.
Shutter of size 450mm x 350mm with 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging including 50 mm long brass hinges
Back 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989 complete all as specified and as directed.
Shelve of cupboard 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging.
25 mm dia chroumium plated Knob with brass nuts and bolts
Legs (front/Rear) 1st class hardwood (TeaK)
Long rail 1st class hardwood (TeaK)
Side rails 1st class hardwood (TeaK)
Bottom Stiffeners 1st class hardwood (TeaK)
Taking out drawer from existing position and refixing the same after minor reppair like tighting thr screw wooden pin complete all as specified.
Repairs to Table Bed side for the following :- Removing old unserviceable fitting and fixture of Table bed side without disturbing to the other parts such as top,legs,side, etc and supply and fixing with new items with 2nd class hardwood (Kalasiris) and 4mm thick wooden beading whereever required and minor repair applying of French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : 28(M)/276/ E6/MAP/15(R))
Top/ bottom of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood (Teak) beading around the edging.
Side of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood (Teak) beading around the edging.
Back Plywood (Make-Green Ply/Kit Ply,Century/Bhutan Board) 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989
Shelve 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood beading around the edging.
Stiffeners in centre of both leg rail 40 mm x 30 mm
Repairs to Almirah Mess Utensil for the following :- Removing old unserviceable fitting and fixture of Almirah Mess Utensil without disturbing to the other parts such as top,legs,side, etc and supply and fixing with new items with 2nd class hardwood (Kalasiris) and 4mm thick wooden beading whereever required and minor repair applying of French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD : 39(M)
Door shutter Left/Right of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood (Teak) beading around the edging and brass hinges 50mm size.
Back Plywood (Make-Green Ply/Kit Ply,Century/Bhutan Board) 9mm thick, 7 No ply, ISI marked conforming to IS: 303-1989
Legs 2nd class hardwood (Kalasiris)
Long rail 2nd class hardwood (Kalasiris)
Side rails 2nd class hardwood (Kalasiris)
Aluminium anodised D handle of size 100 mm
Repairs to Book Case for the following :- Removing old unserviceable fitting and fixture of Book Case without disturbing to the other parts such as legs,rails, top,stiffiners,Drawer etc and supply and fixing with new items of Best quality 1st class hardwood well seasoned (Teak) and 4mm thick wooden beading whereever required and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 45(M)/237 )
Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging.
Bottom of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging.
Shutter with 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging including 50 mm long brass hinges
Sides with 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging.
Back 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989 complete all as specified and as directed.
Partition of bookcase 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick 1st class hardwood (Teak) beading around the edging.
25 mm dia chroumium plated Knob with brass nuts and bolts
Legs (front/Rear) 1st class hardwood (TeaK)
Long rail 1st class hardwood (TeaK)
Short/ Side rails 1st class hardwood (TeaK)
Repairs to Side board for the following :- Removing old unserviceable fitting and fixture of side board without disturbing to the other parts such as top,legs,side, top,drawers etc and supply and fixing with new items with 1st class hardwood (teak) and 4mm thick 1st class hardwood beading whereever required and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 26(M)/241/ 1112)
Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class harwood (Teak) beading around the edging.
Side of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5mm thick timber beading around the edging.
Back Plywood (Make-Green Ply/Kit Ply,Century/Bhutan Board) 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989
Shutter 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood (Teak) beading around the edging. with one knob 25mm dia complete all as specified and as directed.
Shelve 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5mm thick timber beading around the edging. complete all as specified and as directed.
Drawer 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood beading around the edging with one knob 25mm dia complete all as specified and as directed.
Inside partition 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick 1st class hardwood beading around the edging with one knob 25mm dia complete all as specified and as directed.
Bottom 18 mm thick pre-lamintated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4mm thick timber beading around the edging complete all as specified and as directed.
Legs 1st class hardwood (TeaK)
Long rail of bottom 1st class hardwood (TeaK)
Short rail of bottom 1st class hardwood (TeaK)
25 mm dia chroumium plated Knob with brass nuts and bolts
Repairs to Table Drassing Ladies for the following :- Removing old unserviceable fitting and fixture of Table drassing Ladies without disturbing to the other parts such as top,side, glass, mirror,knob etc and supply and fixing with new items and 5 mm thick wooden beading whereever required and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 251)
Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5 mm thick timber beading around the edging.
Side of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5 mm thick timber beading around the edging.
Bottom of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5 mm thick timber beading around the edging.
Back of 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989 complete all as specified and as directed.
Drawer 6mm thick, 4 No ply, ISI marked conforming to IS: 303-1989 front side with 18 mm thick pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 one No 25mm knob of required colour complete all as specified and as directed.
Mirror frame made out of 1st class hardwood (Teak)
Mirror 5.5 mm thick electro copper plated with 6mm thick plywood on back side with key plate (Modi/Atul Saint Gobbin )
Legs 1st class hardwood (TeaK)
25 mm dia chroumium plated Knob with brass nuts and bolts
Aluminum channel for sliding glass with 5 mm thickness ordinary glass
Repairs to Hat stand with mirror for the following :- Removing old unserviceable fitting and fixture of Hat stand with mirror without disturbing to the other parts such as Particle Board,matel peg,mirror etc and supply and fixing with new items of Best quality and minor repair applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No: FD: 233)
Base of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 5 mm thick timber beading around the edging.
Chromium plated metal peg 120 mm long
Mirror 5 mm thick electro copper plated of size 300mm x 460 mm (Modi/Atul Saint Gobbin )
Repairs to Chair Dining JCO/Ors for the following :- Removing old unserviceable fitting and fixture of Chair Writing without disturbing to the other parts such as legs,rails, stiffiners, Hand rest etc and supply and fixing with new items of Best quality 1st Class HW (Teak)) and minor repair applying French Polishone or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD-MAP/ II /05 )
Rear legs 1st class hardwood (TeaK)
Front legs. 1st class hardwood (TeaK)
Stiffener.1st class hardwood (TeaK)
Seat rail (Front /rear and side ) 1st class hardwood (TeaK)
Stiffener back rest 1st class hardwood (TeaK)
PVC Seat frame Make: AMKO
Material and labour for preparing & polishing wooden and wood based materials of any description and of any lenghth and width and applying french polish to furniture articles as specified with one or more coat till glossy finish achieved including filler as required all as specified in particular specifications and as shown on drawing and as directed by Engineer-in-Charge for the following wooden furniture:-
Bed Ply wood Top (Escept plywood) (Drawing No. FD- 213/ 246 M)
Chair Writing (Drawing No. FD- 20(M)/ 280)
Chair Dining (Drawing No. FD- 16(M)/228//279 )
Table wooden without drawer 900 mm x 900 mm x 760mm (Drawing No. FD- 88(M) 201)
Table 3' x 2' with drawer (Drawing No. FD- 41(M)/283)
Table 3' x 2' with out drawer (Drawing No. FD- 42(M)/55(M)/231/284)
Peg Table (Drawing No. FD- 277/384)
Teapoy (Drawing No. FD- 34(M)/ 278)
Table Centre (Drawing No. FD- 29(M)/235/ 274)
Table Dining 8/6 persons (Drawing No. FD- 30(M) /273)
Chair Wooden Bottom without arms (Drawing No. FD- 56(M)/285)
Chair Easy (Drawing No. FD-17/229)
Table Writing (Drawing No. FD- 33(M)/ 249/ 275)
Table bed side (Drawing No. FD- 28(M)/ 276/ E6/MAP/15(R))
Almirah mess utensil (Drawing No. FD- 39(M)
Book Case Large/ Small (Drawing No. FD-45(M)/ 237 )
Side Board (Drawing No. FD- 26/241/ 1112)
Table dressing ladies (Drawing No. FD- 33/249/251 and FD/MAP/II/07)
Hat stand with Mirror (Drawing No. FD- 206/233)
Chair Dining (Drawing No. FD- MAP/II/05)
Sofa Chair 4 (2+1+1) Seater Wooden (Drawing No. FD- 281 )
Sofa set 5 (Five) (3+1+1 ) Seater Wooden (Drawing No. FD- 281)
STEEL FURNITURE Taking down existing unserviceable Top of Table office clerk Steel and supply and fixed with new 6mm thick veneered decorative ply wood, grade 1st quality with BWR resin with decorative face veneer on one face in same position with new screws including providing aluminium beading all round as per existing shape and size complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1004)
Taking down existing unserviceable lock lever of Table office clerk Steel and supply and fixed with new steel lock 6 (six) lever for drawer with duplicate key in same position with new screws complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1004)
Material and labour for spot welding in repairs of broken steel frame and drawer of table office clerk steel complete all as directed. (DRAWING No. 84(M)/FD-1004) (Note :- Each spot shall not exc. 5 cm in length and not exc. 2mm in thickness.)
Taking down existing unserviceable Top of Table office Officer Steel and supply and fixed with new 6mm thick veneered decorative ply wood, grade 1st quality with BWR resin with decorative face veneer on one face in same position with new screws including providing aluminium beading all round as per existing shape and size complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1003)
Taking down existing unserviceable steel lock lever of Table office Officer Steel and supply and fixed with new steel lock 6 (six) lever for drawer with duplicate key in same position with new screws complete all as specified and as shown on drawing. (DRAWING No. 84(M)/FD-1003)
Material and labour for spot welding in repairs of broken steel frame and drawer of table Office Officer steel complete all as directed. (DRAWING No. 84(M)/FD-1003) (Note :- Each spot shall not exc. 5cm in length and not exc. 2mm in thickness.)
Taking down existing unserviceable table top 900 mm x 600 mm with and without drawer Steel and supply and fixed new Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick teak wood beading around the edging all complete specified shown on drawing & directed. (Drawing No. FD 1007)
Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of Table complete all as specified and as shown in drawing. (Drawing No. FD 1007) (Note : Material to be weled not to exceeding 2.00mm in thickness)
Taking out unserviceable plastic cane of chair Verandah seat and back and supply and fixing for weaving the seat and back of Chair Varandah in Godrej pattern with new 4 mm wide half round approved quality cane on steel surface of chair complete all as specified and as directed. (Drawing No. FD-19(M)/256/359)
Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of chair verandah complete all as specified and as shown in drawing. (Drawing No. FD- 19(M)/256/359) (Note : Material to be weled not to exceeding 2.00mm in thickness)
Taking down decayed top from Table dining ORs and supply and fixing new top 18 mm thick pre-laminated particle board, Grade II Type I exterior grade conforming to IS-12823-2006 with 4mm thick teak wood beading all around the edging complete all as specified and as directed. (Drawing No. FD-165(M)
Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of chair verandah complete all as specified and as shown in drawing. (Drawing No. FD- 165(M) Note : Material to be weled not to exceeding 2.00mm in thickness)
Taking out unserviceable seat frame of Chair CB with Arm and Supply and fixed Seat frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat frame shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat and back in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).
Taking out unserviceable back frame of Chair CB with Arm and Supply and fixed Back frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of back frame shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat and back in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).
Taking out old rusted/damaged/broken flat iron support of chair CB steel with arms and supply and fixed new mild steel flat iron of size 20 x 5mm, 75mm long to bottom of steel frame in support of wooden seat frame duly welded with making hole for fixing screw complete all as specified and as shown on drawing. (Drawing No. FD-75(M).
Taking out old damaged/broken arm rest and supply and fixed new arm rest in the same position as per existing shape and size made out of well seasoned first class hard wood ‘Teak ’ timber including applying two coat of black paint over wood filler on all exposed new wooden surfaces after preparation of new wooden surfaces complete all as specified and as shown on drawing. (Drawing No. FD-75(M).
Taking out unserviceable seat frame of Chair CB without Arm and Supply and fixed Seat and Back frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).
Taking out unserviceable back frame of Chair CB without Arm and Supply and fixed Seat and Back frame made from Teak wood well seasoned and termite treated, with making holes of weaving slightly rounded on the edges and applying two coat of black paint over wood filler on all exposed new wooden surfaces of seat shall be painted with high glossy paint after preparation of new wooden surface and weaving with new cane seat in "Godrej" pattern with 2mm wide plastic cane for main canning and border with 3.5-5 mm cane bordering and 0.4mm thick gola type weighing not less than 6 gms per 10 running meters complete all as specified & as directed and as shown on drawing.complete all as specified and shown in drawing. (Drawing No. FD-75(M).
Taking out old rusted/damaged/broken flat iron support of chair CB steel without arms and supply and fixed new mild steel flat iron of size 20 x 5mm, 75mm long to bottom of steel frame in support of wooden seat frame duly welded with making hole for fixing screw complete all as specified and as shown on drawing. (Drawing No. FD-75(M).
Taking down existing unserviceable Teapoy Verandah top and supply and fixed new Top of 18 mm thick Pre-laminated particle board Grade II Type I exterior grade conforming to IS-12823-2006 with one side teak finish fixed with 4 mm thick teak wood beading around the edging all complete specified shown on drawing. (Drawing No. FD 35(M)/255)
Material and labour in repair to broken frame leg of teapoy verandah by spot welding not exc 2.50cm in length complete all as specified and as directed. (Drawing No. FD 35(M)/255) (Note : Materials to be welded not exc. 2.50 cm in thickness).
Taking down existing unserviceable leg (Right/Left) of Locker bed side steel and supply and fixed with new Leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel sheet in same position and applying two coatss of Synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer complete all as specified and shown on drawing. (Drawing No. FD-257/1029)
Material and labour in repair to broken/damaged bottom leg of locker bed side steel by spot welding complete as specified and as directed. (Drawing No. FD-257/1029) (Note: Thickness of metal to be welded shall not exceed 2mm.)
Taking out loose shelf from of locker Bed Side Steel and refixing the same position rigidly after minor repairs by providing new clips, nut and bolts as required complete all as directed. (Drawing No. FD-257/1029)
Taking out existing unserviceable hasp and stapple and Supply and fixed new hasp and staple of size 100 mm x 20 mm x 3 mm Chromium plated Hasp and staple to front shutter of approved make and design complete all as specified and as shown on drawing (Make :- Mowjee or Classic) (Drawing No. FD-257/1029)
Material and labour in repairing of existing unserviceable hinges by spot welding and make it functional by providing pin/greasing etc. complete all as directed. (Note :- Each spot welding shall not be more than 2.5cm in length and materials to be welded not exceeding 3mm in thickness.) (Drawing No. FD-257/1029)
Taking out of unserviceable old handles from the front of shutter and Supply and fixed new 115mm long chrome plated handle of approved make and design complete all specified and as shown on drawing. (Drawing No. FD-257/1029)
Taking out of old unserviceable broken curtain rod including brackets and Supply and fixed new curtain rod of aluminium 19/20mm dia, 1.5 mm wall thickness with steel brackets both sides in the same position by spot welding including painting with applying two coat of Olive Green synthetic enamel paint (1st quality over a coat of red oxide zinc chrome primer by spray machine over steel brackets after preparation of new steel surfaces complete all as specified and as shown on drawing. (Drawing No. FD-257/1029)
Taking out old unserviceable/damaged bottom shelf and Supply and fixed new bottom shelf as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)
Taking out old unserviceable/damaged intermediate shelf and Supply and fixed new intermediate shelf as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)
Taking out old unserviceable/damaged inner partition and Supply and fixed new inner partition as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)
Taking out old unserviceable/damaged shutter (Left/Rigt) and Supply and fixed new shutter as per existing shape and size made out of 1mm thickness plain mild steel sheet and fixed in the same position with shelf clips, nuts & bolts etc including applying painting with two coat of Olive Green synthetic enamel paint (1st quality) over a coat of red oxide zinc chrome primer by spray machine before fixing and after preparation of new steel surfaces complete all as specified and shown on drawing. (Drawing No. FD-257/1029)
Repair of Almirah steel large with shelves as appended below : Taking down existing unserviceable botton leg (left/right) from its position and supply and fixed new bottom leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)
Taking down existing unserviceable door shutter by cutting area not exc.100 Sqcm squre/rectangle from its position and supply and fixed new door shutter made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)
Taking down existing unserviceable bottom shelve from its position and supply and fixed new shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)
Taking down existing unserviceable intermediate shelve from its position and supply and fixed new intermadiate shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)
Taking down existing unserviceable door shutter from its position and supply and fixed new door shutter (Left/ Right) out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1031)
Taking out unserviceable damaged lock from its position of almirah (large steel) and Supply and fixed new 6 lever steel lock as per existing shape and size as approved with keys in duplicate complete all as specified. Make :Link/Godrej/Standard/Aligarh ( Drawing No. FD-67(M)/FD-1031)
Taking out old and removing old unserviceable handle from Almirah steel large and Supply and fixed steel chromium plated handle 125mm long of existing shape and size complete all as specified and as directed and shown on drg.(Make :- Mowjee or Classic) ( Drawing No. FD-67(M)/FD-1031)
Taking out loose shelf from its position of Almirah large steel and re-fixing the same rigidly after minor repairs by providing new clips, nuts & bolts of existing size as required complete all as directed. ( Drawing No. FD-67(M)/FD-1031)
Material and labour for running welding in repairs to broken/damaged sides (left/right), back and top of almirah steel large complete all as directed. (Note : Thickness of materials to be welded not exceeding 2mm in thickness and length of each welding exceeding 9mm but not exceeding 20mm in length) ( Drawing No. FD-67(M)/FD-1031)
Material and labour for repair of existing loose hinges by spot welding and make it functional by providing new steel pin including greasing etc required for smooth function complete all as directed. ( Drawing No. FD-67(M)/FD-1031)
Material and labour for taking out loose leg (right/left) from its position and re-fixing the same in existing position with necessary run welding of Almirah large complete all as directed. (Note : Thickness of metal to be welded shall not exceed 2mm) ( Drawing No. FD-67(M)/FD-1031)
Repair of Almirah steel Medium with shelves as appended below : Taking down existing unserviceable botton leg (left/right) from its position and supply and fixed new bottom leg of size 450 mm x 80 mm x 100 mm made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)
Taking down existing unserviceable bottom shelve from its position and supply and fixed new shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)
Taking down existing unserviceable intermediate shelve from its position and supply and fixed new intermadiate shelve made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)
Taking down existing unserviceable door shutter from its position and supply and fixed new door shutter made out of 1mm Mild steel and applying two coatss of Synthetic enamel paint (1 st quality) OG over a coat of red oxide zinc chrome primer complete all as specified shown on drawing. ( Drawing No. FD-67(M)/FD-1032)
Taking out and removing of old broken/damaged steel of door shutter with necessary cutting in square/rectangle in shape and Supply and fixed new MS sheet as per existing size and shape not exceeding 100 Sq cm each made out of 1 mm thickness plain mild steel sheet fixed by run welding of required length including applying two coat of synthetic enamel paint (1st grade quality) over a coat of red oxide zinc chrome primer by spray machine all complete as specified and as directed. ( Drawing No. FD-67(M)/FD-1032)
Taking out unserviceable damaged lock from its position of almirah (medium steel) and Supply and fixed new 6 lever steel lock as per existing shape and size as approved with keys in duplicate complete all as specified. Make :Link/Godrej/Standard/Aligarh ( Drawing No. FD-67(M)/FD-1032)
Taking out old and removing old unserviceable handle from Almirah steel medium and Supply and fixed steel chromium plated handle 125mm long of existing shape and size complete all as specified and as directed and shown on drg.(Make :- Mowjee or Classic) ( Drawing No. FD-67(M)/FD-1032)
Material and labour for running welding in repairs to broken/damaged sides (left/right), back and top of almirah steel medium complete all as directed. (Note : Thickness of materials to be welded not exceeding 2mm in thickness and length of each welding exceeding 9mm but not exceeding 20mm in length) ( Drawing No. FD-67(M)/FD-1032).
Material and labour for repair of existing loose hinges by spot welding and make it functional by providing new steel pin including greasing etc required for smooth function complete all as directed. ( Drawing No. FD-67(M)/FD-1032)
Taking out loose shelf from its position of Almirah medium steel and re-fixing the same rigidly after minor repairs by providing new clips, nuts & bolts of existing size as required complete all as directed. ( Drawing No. FD-67(M)/FD-1032)
Material and labour for taking out loose leg (right/left) from its position and re-fixing the same in existing position with necessary run welding of Almirah large complete all as directed. (Note : Thickness of metal to be welded shall not exceed 2mm) ( Drawing No. FD-67(M)/FD-1032)
Taking out old damaged / decayed tapestray cloth and supply and fixed with new with superior quality tapestry cloth of approved colour, taxture and quality as per existing shape complete all as directed. ( Drawing No. FD/E6/MAP/12) (Note : The cost of tapestry cloth should be min of Rs. 275/- per mtr).
Taking out old existing damaged / broken seat frame of chair verandah and refixing the same with new seat frame complete all as specified and as shown in drawing. (Make of seat frame : AMKO or equivalent as approved by GE). ( Drawing No. FD/MAP-II /06)
Taking out old existing damaged / broken back frame of chair verandah and supply and fixed with new back frame complete all as specified and as shown in drawing. (Make of seat frame : AMKO or equivalent as approved by GE). ( Drawing No. FD/MAP-II /06)
Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of chair verandah complete all as specified and as shown in drawing. ( Drawing No. FD/MAP-II /06) (Note : Material to be weled not to exceeding 2.00mm in thickness)
Material and labour for spot welding in repairs not exc 2.50cm in length of broken steel frame of shoe rack steel complete all as specified and as shown in drawing. (Note : Material to be weled not to exceeding 2.00mm in thickness) ( Drawing No. FD/E6/MAP/2(R)
Removing of old existing unserviceable plywood top from charpoy IP Hard Top MS squre pipe , tightening the frame including welding whereever required and Supply and fixing new plywood 12mm thick BWR, ISI marked, conforming to IS: 303-1989 (size Approx 1950 mm x 900 mm) with MS cleat and stiffener screw and cup washer all as spacified and directed. ( Drawing No. FD/MAP/II/ 01)
Supply and fixing in repairs Stiffener of size 25mm x 25mm MS square tube1.5 mm wall thickness including necessary welding as per existing and as shown in drawing all as spacified and directed. ( Drawing No. FD/MAP/II/ 01)
SOFA SETS Taking out of unserviceable back long rail from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 35 mm x 70 mm x 1680mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)
Taking out of unserviceable stiffener in seat and back from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 20 mm x 50 mm x 600mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)
Taking out of unserviceable Arm rest (Handle) from sofa 5 seater (3+1+1) and Material and labour with new 1st class hard wood (Teak Wood) arm rest (Handle) as per existing, well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)
Taking out of unserviceable cover of tapestry cloth with lining from Foam cushion of size 560mm x 530mmx100mm and supply and stiching with new lining and best quality tapestry cloth of approved quality and colour (not less than Rs. 280/- per RM) duly wraped and cover shall be of removable type by providing best quality plastic Zip over Tapestry cloth complete all as specified and as directed. (Drawing No. FD- 281)
Taking out of unserviceable Foam cushion and supply and fixed new foam cushion 100 mm thick 'U' foam, 40 density, of size 500 mm x 530 mm all as directed. (Foum shall be sleepwell/courlon/ Sleepwell/ Dunlop). (Drawing No. FD- 281)
Taking out of unserviceable back long rail from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 35 mm x 70 mm x 1120mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)
Taking out of unserviceable stiffener in seat and back from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) of size 20 mm x 50 mm x 600mm , well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)
Taking out of unserviceable Arm rest (Handle) from sofa 4 seater (2+1+1) and Material and labour with new 1st class hard wood (Teak Wood) arm rest (Handle) as per existing, well seasoned and applying French Polish one or more coat till glossy finish achieved to match with existing surface complete all as specified and shown on drawing. (Drawing No. FD- 281)
Taking out of unserviceable cover of tapestry cloth with lining from Foam cushion of size 560mm x 530mmx100mm and supply and stiching with new lining and best quality tapestry cloth of approved quality and colour (not less than Rs. 280/- per RM) duly wraped and cover shall be of removable type by providing best quality plastic Zip over Tapestry cloth complete all as specified and as directed. (Drawing No. FD- 281)
Taking out of unserviceable Foam cushion and supply and fixed new foam cushion 100 mm thick 'U' foam, 40 density, of size 500 mm x 530 mm all as directed. (Foum shall be sleepwell/courlon/ Sleepwell) (Drawing No. FD- 281)
Removing of old PVC shoe from various Type of Tables such as Table Writing, table 3'x2' with /witout drawer, Table 3'x3', table 2'x2' Table office Clerk, table dining 6/8 person, Sofa set, Charpoy IP Hard Top etc. and replacing the same with new 25mm dia and 20 mm high be screwed to bottom of legs all as specified an das directed.
Removing of old PVC shoe/ Cap from various Type of Chairs such as Chair dining, Chair Writing, Chair Easy, Chair WB,Chaier CB etc.and replacing the same with new 20 mm dia and 10 mm high be screwed to bottom of legs all as specified an das directed.
Material and labour for spot welding to damaged/broken seat frame of chair CB with Arm complete all as specified and shown on drawing. (Drawing No. FD-75(M). (Note : length of each spot welding will not exceed 2.50 cm in length and 2 mm in thichness).
Material and labour for spot welding to damaged/broken seat frame of chair CB without Arm complete all as specified and shown on drawing. (Drawing No. FD-75(M). (Note : length of each spot welding will not exceed 2.50 cm in length and 2 mm in thichness).
Removing dents, bends welding to broken portion rectifying all minor defects and repairs. Material and labour for preparation of steel surface (inside & outside surface) including doors shelves and legs, applying synthetic enamel paint (1st quality) over a coat of red oxide primer Zinc chrome primer by spray paint machine complete all as specified specified and shown on drawing for following:-
Tabble Office Clerk Steel (Drawing No. FD-84(M)/ 1004 )
Tabble Office Officer Steel (Drawing No. FD-84(M)/ 1003 )
Tabble Steel 900 x 600 x 760 mm (Drawing No. FD- 1007 )
Chair Verandah (Drawing No. FD- 19(M) /256/ 359 )
Tabble Dinning Ors (Drawing No. FD- 165(M) )
Chair CB Steel with arms (Drawing No. FD- 75(M) )
Chair CB Steel without arms (Drawing No. FD- 75(M) )
Locker bed side steel. (Drawing No. FD- 257/ 1029)
Almirah Large Steel (Drawing No. FD-67(M)/ 1031)
Almirah Medium Steel (Drawing No. FD-67(M)/ 1032 )
Chair Writing (Drawing No. FD- E6/MAP/ 12 )
Chair Verandah (Drawing No. FD- MAP/-II/ 06 )
Shoe Rack Steel (Drawing No. FD- E6/ MAP/ 02® )
Charpoy IP with Hard Top (Drawing No. FD/ MAP-II/ 01 )
Teapoy verandah (Drawing No. FD- 35(M) /255 )
samrat saw mill and joinery workshop
ANIL KUMAR GUPTA
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.04 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .