Renovation of Guwahati Guest House

Amount

Civil Works

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Reinforcement cement conrete work in walls (any thikness), including attached pilasters, buttresses, plinth and string courses, fillest, Columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1.:1.5.:3 (1 cement : 1.5 coarse sand (Zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for: Lintels, beams, plinth beams, girders, bressumers and cantilevers

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade , Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture.

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 1000x1000 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size, Size of Tile 1200x1200 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 65 x 125 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately), 35 mm thick

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape. colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads. interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head. comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 Part 1 to 14, plastic packers. plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion elded/mechanically jointed duly sealed at all comers, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with/without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note: Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (i) Sites with basic wind speed 45 m/sec as per IS 875 Part 3 (i) Sites with structure height more than 20m for all wind speeds,

, Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylan rollers with SS 304 body. 9.147 A1.1 Using R2 series with frame (40 mm & above)x (40 mm & above) & sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak)powder coated touch locks with hook (Height upto 1.2 metre).

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab all colour and texture except black, Cherry/ Ruby red, Area of slab upto 0.50 sqm

Providing and fixing 150 mm bright finished floor brass door stopper with rubber cushion, necessary brass screws etc. to suit shutter thickness complete

Providing and fixing chromium plated brass butt hinges with necessary chromium plated brass screws etc. complete, 75x65x4 mm (heavy type)

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.100 mm nominal size dia

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing , fitting & fixing of Godrej Cylindrical Lock suitable for Doors.

Providing fitting and fixing of Curtain Bracket SN147

Repaiting and Painting Works

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :(Steel Surface). One or more coats on old work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :(Wooden Surface). One or more coats on old work

French spirit polishing : One or more coats on old work

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Renewing glass panes and refixing existing wooden fillets: Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm)

Refixing old glass panes with putty and nails.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 50 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25 mm nominal dia Pipes

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 15 mm nominal dia Pipes

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete

Plumbing and Sanitary Works

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 453x357 mm

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms.

Providing and fixing chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. Including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &b fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 50 mm dia.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC Plain brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia. Pipes.

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore

Providing and fixing brass bib cock of approved quality : 20 mm nominal bore

Providing and fixing brass stop cock of approved quality : 15 mm nominal bore

Providing and fixing brass stop cock of approved quality : 20 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.

Providing fitting and fixing C.P Bib cock COP-CHR-037PM

Providing fitting and fixing C.P Towel ring Diamond-741820

Providing fitting and fixing C.P soap Dish Diamond D503

Providing fitting and fixing C.P Shower arm SHA-CHR-477

Over head Shower Jaquar make 1" x 1"

Providing fitting and fixing Concealed Cistern with control plate Jaquar make JCS-WHT-2400FS-SPS with JCP-CHR-325415-CONTROL PLATE

Providing and fixing wall hanging Commode Jaquar make etc. complete APS WHT 39953BIUFSM

Providing fitting and fixing C.P Twin Bib cock Jaquar make FUS-CHR-29041

Providing fitting and fixing C.P Angle Stop cock Jaquar make FUS-CHR-29053

Providing fitting and fixing Hand wash Bottle Dispenser with Stand Jaquar make CAN-CHR-1135N

Supplying, fitting & fixing CP concealed health faucet shower Agmeco make with 1.2 metre flexible tube &ABS wall bracket etc. complete Jaquar make

Towel Rod Jaquar make

Overhauling of iron removal filter including uploading of media from the vessel , cleaning of vessel , supplying of new iron rempoval filter media sets. Supply of 1 & 1/2 " multipot valve, new alum dozer PVC strainer set, pressure gauze, 1 & 1/2 " operating line and air vaccuam etc complete.

Electrical Works

Wiring for light/fan/exhaust fan/call bell point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/recess PVC conduit with modular switch, modular plate, suitable G.I. box and earthing the point with 1.5 sq. mm FRLS PVC copper cable as required. Group A

Wiring for circuit/submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recess as required.

2x2.5 sq. mm+ 1X2.5 sq. mm earth wire

2X4 sq. mm+ 1X4 sq. mm Earth wire

4X10Sq.mm + 2X6Sq.mm earth wire

Supply and fixing following size/modules G.I. box along with modular base and cover plate for modular switches in recess etc. as required.

4 module

6 module

8 module

Supply and fixing modular blanking plate on the existing modular plate and box excluding modular plate as required.

Supply and fixing 2 module step type electronic fan regulator on the existing modular plate switch box including connection but excluding plate

Supplying and fixing modular switch/socket on the existing modular plate and switch box including connection but excluding modular plate as required.

15/16 A switch

6 pin 15/16 A socket outlet

3 pin 5/6 A socket outlet

5/6A Switch

Supply, installation,testing and commissioning of 1200 mm sweep, BEE 5 Star rated Ceiling fan with Brushless direct current motor. Class of insulation B, 3 no.s of blade, 30 cm long down rod, 2 no.s canopy, shackled kit, safety rope, copper winding, power factor not less than 0.9, service value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/min, 350 rpm (tolerence as per IS: 374-2019). thd less than 10% with electronic regulator for speed control and all remaining accesssories including safety pin, nuts and bolts, washers, temperature rise =75º C(max) insulation resistence more than 2 MΩ, suitable for 230V, 50Hz, 1-φ AC supply, earthing etc. complete as required.

Supply Fitting & Fixing of industrial type 300mm sweep exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.

supply, installation,testing and commissioning of 20 W LED Tube Fixtures including connections etc. complete as directed

Supply fitting and fixing of 10W LED bed side light complete with LED lamp and conections etc.

Supply fitting and fixing of 10W LED wall light set complete with LED lamp and conections etc.

Supplying and fixing following way surface/recess mounting vertical type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 8 way (4+24), Double door

Providing and fixing following rating and breaking capacity and pole MCCB with thermo magnetic release and tertminal spreaders in existing cubicle panel board/DB including drilling holes in wall, making connections etc. as required complete. 125A, 36KA, four pole MCCB

Supplying and fixing 5A to 32 A rating,240/415 V, 10 KA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and comissioning etc as required. Single Pole

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc. as required. Upto 35 sq. mm

Supply of 4 core 35 sq. mm armoured aluminium cable.

Supply, fitting and fixing retrofit LED bulb

supply, installation,testing and commissioning of 12 W LED recessed Round panel light fixtures including connections etc. complete as directed

Supply, fitting and fixing of required sizes of fan hook by fitting fastening nuts and bolts etc. complete as directed.

Supply, fitting and fixing of modular Air-Conditioner starter with board and connections etc. as required complete

Providing and fixing 4mm dia copper wire on surface or in recess for loop earthing as rquired.

Supplying and fixing following way horizontal type three pole and neutral, sheet stoel, MCB distribution board, 415 V, on surface/rocess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). 6 way(4+18), Double Door

Supplying and fixing following rating four pole, 415 V, isolator/MCB in existing MCB DB complete with connections, testing and commissioning etc as required. 63A

Supply, fitting and fixing of 16A plug top (for AC and geyser)

Supply, fitting and fixing of 16A Socket (for AC and geyser)

Supplying and fixing metal box of following sizes on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required. (100 x 100 x 60) mm

Supply, Installation, testing and commissioning of 1.5 tr. Split Hi-wall type Air Conditioner.

Supply, Installation, testing and commissioning of Electric Water Heater (Geyser), capacity 10L

M.P.KHAITAN (BID ID -3221291)

DNS Construction Co (BID ID -3221232)