GENERAL RC2 PHASE 1RM 2023 24 R C 2 Phase 1 One year RC Pulinkunnu Section Alappuzha RM 2023 24 Zone 4 Work Name One year Running Contract of various PWD roads under Road Section Pulinkunnu in Alppuzha District 2 road stretches for a length of 6 111K

Amount

Appendix A- Urgent patch works

2.2:Clearing grass and removal of rubbish up to a distance of 50 metres outside the periphery of the area

OD81201/2023-2024:Dismantling of flexible pavements and sectioning the dismantled material and re rolling .

55.4:Supplying and stacking 36mm size hard broken stone in standard heaps for measurement.

55.7.a:Providing bitumen leveling coarse between 40mm and 150mm with 36mm deptl metal by spreading the metal to line and levels and rolling until the compacted coarse aggregate has a firm surface and applying hot bitumen with pressure sprayer at the rate of 20 Kg per M3 metal including all cost of bitumen conveyance heating mixing spreading in appropriate locations to proper levels compacting with power roler and other sundry stores.

55.8.a:Filling up pot holes (cut and formed to regular shapes and all loose and defective materials removed) after supplying a prime coat of hot bitumen using 36mm departmental broken stone and compacting with power roller to get a compact surface.

OD81202/2023-2024:Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2.

4.2.A.2:Construction of granular sub-base by providing graded material, spreading in uniform layers with a motor grader on a prepared surface, mixing by mix in-place method with rotavator at OMC, and compacting with a vibratory roller to achieve the desired density, complete as per clause 401. Grading-IV - For lower sub-base - Mix in Place Method

4.12:Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

5.1.a:Providing and applying primer coat with bitumen emulsion ( SS) on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 - 1.0 kg/sqm using mechanical means.

5.2.a:Providing and applying tack coat with bitumen emulsion( RS) using emulsion pressure distributor at the rate of 0.20 - 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

OD81203/2023-2024:Mix seal Surfacing Providing, laying and rolling of close-graded premix surfacing material of 20mm thickness compossed of 11.2mm to 0.9mm Type-A aggregate using penetration grade bitumen to required line, grade and level to serve as wearing course on previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 KN static roller and finishing to required level and grades as per Technical specification cluse 509 of MORD(Usage of bitumen is 22.00kg /(10m2) By Manual Means

Appendix B- Premonsoon Works

10.2:Maintenance of Earthen Shoulder (filling with fresh soil) Making up the loss of material/ irregularities on the shoulder to the design level by adding fresh approved soil and compacting it with appropriate equipment.

OD81204/2023-2024:Engaging wood cutter for cutting trees & branches leaned towards the road threatening to pedestrains & traffic

OD81205/2023-2024:Providing wood cutting machine for cutting the trees

OD81206/2023-2024:JCB for removing the Wood etc

OD81207/2023-2024:Engaging tipper for removing wood & material from road side as per the direction of departmental officers etc

OD81208/2023-2024:Engaging mazdoor for lowering side berms ,clearing side drains, removing silt from culverts, cutting earthern drain,Diverting blocked water ,assisting wood cutter in cutting dangerous trees branches of trees leaned towards the road threatening pedestrains & traffic & removal of fallen trees for branches on the roads, clearing traffic blockage ,stacking the wood in a suitable place & other various works as directed by the Engr in charge

OD81209/2023-2024:Engaging heavy load mazdoor for removing cover slab & resetting after cleaning etc.

OD81211/2023-2024:Filling up pot holes with bituminous ready mix compound (25kg Bag) and compacting & ramming to get a compact surface including material , laying charges ,tansportation to the site etc complete { Rate is arrived for a Bag of 25 Kg }

55.15:Refurbishment of existing signboardsRefurbishment of existing signboards of all size except gantry mounted ones to their original reflectivity & position by removing obstructions like overgrowth vegitation etc ,if any,washing the signboards with water & soap solution to remove all dirt, oil etc. , correcting any dislocations including minor repairs, replacement of lost nut and bolts etc complete.

Appendix C : Anticipatory Works

2.2:Clearing grass and removal of rubbish up to a distance of 50 metres outside the periphery of the area

55.4:Supplying and stacking 36mm size hard broken stone in standard heaps for measurement.

55.7.a:Providing bitumen leveling coarse between 40mm and 150mm with 36mm deptl metal by spreading the metal to line and levels and rolling until the compacted coarse aggregate has a firm surface and applying hot bitumen with pressure sprayer at the rate of 20 Kg per M3 metal including all cost of bitumen conveyance heating mixing spreading in appropriate locations to proper levels compacting with power roler and other sundry stores.

55.8.a:Filling up pot holes (cut and formed to regular shapes and all loose and defective materials removed) after supplying a prime coat of hot bitumen using 36mm departmental broken stone and compacting with power roller to get a compact surface.

4.1.B.1:Construction of granular sub-base by providing graded material, spreading in uniform layers with a motor grader on a prepared surface, mixing by mix in-place method with rotavator at OMC, and compacting with a vibratory roller to achieve the desired density, complete as per clause 401. Grading-V - For sub-base cum drainage layer - Mix in Place Method

4.12:Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

5.2.a:Providing and applying tack coat with bitumen emulsion( RS) using emulsion pressure distributor at the rate of 0.20 - 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.

OD81212/2023-2024:Mix seal Surfacing Providing, laying and rolling of close-graded premix surfacing material of 20mm thickness compossed of 11.2mm to 0.9mm Type-A aggregate using penetration grade bitumen to required line, grade and level to serve as wearing course on previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 KN static roller and finishing to required level and grades as per Technical specification cluse 509 of MORD(Usage of bitumen is 22.00kg /(10m2) By Manual Means

OD81213/2023-2024:Engaging labour with passenger car not less than 1000 CC for Conducting and reporting routine inspection upto 20km per day for the entire length of project road at a frequency of 7 days through out the agreement period of running contract as directed by Deparmental Officers .

Appendix D :- Preventing /Reviving affected area in Natural calamities

OD81196/2023-2024:Engaging mazdoor for lowering side berms ,clearing side drains, removing silt from culverts, cutting earthern drain,Diverting blocked water ,assisting wood cutter in cutting dangerous trees branches of trees leaned towards the road threatening pedestrains & traffic & removal of fallen trees for branches on the roads, clearing traffic blockage ,stacking the wood in a suitable place & other various works as directed by the Engr in charge

OD81197/2023-2024:Engaging wood cutter for cutting trees & branches leaned towards the road threatening to pedestrains & traffic

OD81198/2023-2024:Providing wood cutting machine for cutting the trees

OD81199/2023-2024:JCB for removing the Wood etc

OD81200/2023-2024:Engaging tipper for removing wood & material from road side as per the direction of departmental officers etc

4.12:Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

Appendix E : Traffic Safety Works

8.4.2:Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per IRC :67 made of Type IV micro prismatic grade sheeting vide clause 801.3.3 fixed over aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with suitable back supporting frame of MS angle 25x25x3 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc.<br> 60 cm equilateral triangle

8.13:Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads on Bituminous Surface @ 250 gms per sqm area, the thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform, and free from streaks and holes.

8.4.3:Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per IRC :67 made of Type IV micro prismatic grade sheeting vide clause 801.3.3 fixed over aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with suitable back supporting frame of MS angle 25x25x3 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc.<br> 60 cm circular

8.4.12:Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign with 7years warranty manufactured as per IRC :67 made of Type IV micro prismatic grade sheeting fixed over aluminum sheeting, 2 mm thick/aluminum composite material sheeting 4 mm thick with suitable back supporting frame of MS angle 25x25x3 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc. 50cmx 60 cm rectangular (Single chevron etc.)

8.5:Providing and fixing of direction and place identification retro-reflectorised sign with 7 years warranty manufactured as per IRC :67 made of Type IV micro prismatic grade sheeting fixed over aluminium sheeting, 2 mm thick/ aluminium composit material sheeting 4 mm thick with area not exceeding 0.9 sqm, with suitable back supporting frame of MS angle 40x40x6 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc.

OD165248/2023-2024:Providing and fixing of DLP board for Running contract work with Non-retro-reflectorised Vinyl sign with 1 years warranty manufactured Vinyl Printed sheeting fixed over aluminum sheeting 2 mm thick/ aluminium composit material sheeting 4 mm thick with area notexceeding 0.9 sqm, with suitable back supporting frame of MS angle 40x40x6 and supported on GI pipe pole 50mm NB confirming to IS 1239 firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete min size 45 cm x 45 cm x 60 cm, 60 cm below ground level including painting all exposed surface with 2 coats of epoxy painting over epoxy primer and as per approved drawing and clause 801 including lettering symbols etc.

Bidder Name

JOSHY VARGHESE