Special Repair To Bldg No 1037 (04 Qtrs) JCOs Md Accn and Bldg No P-370 (Single Offrs Accn) At Army Area Jodhpur

Amount

Demolition of cement concrete in ground floors and pavings n. exe 15 cm thickness (below or above ground level) complete all as specified & as directed.

M & L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in flooring, path , sub foundation etc complete all as specified and directed.

M&L 50mm thick PCC 1:3:6 type C-2 using 20 mm graded stone aggregate as in plinth protection or similar places, without using extra cement complete all as specified and directed.

S&F machine made precast cement concrete blocks (rubberised interlocking pavers) of 60mm thick with 6mm top layers of ante abrasive rubrised material laid over 25mm thick sand cushion . The interlocking joints shall be filled with fine sand . The compressive strength of layer shall not be less than 350 Kg/Cm2 complete all as specified and directed.

S&F machine made precast cement concrete curb stone blocks using Cement concrete 1:3:6 type C2 (20mm stone agg) all as directed by Engr-in-Charge.

Demiolition of reinforced cement concrete of staircase, landing, chajjas and similar suspended work of any description and any position not otherwise

Demolition of stone masonry built in cement mortar

M&L for cutting in to old masonry to form toothings for bonding in new brick or stone work including making good in cement mortar 1:6 complete all as specified and directed.

M&L for squarred rubble walling Jodhpur type regular coursed well bonded ,bedded and solidly hearted built in cement mortar 1:6 complate all as specified and directed.

All as per item No 8 above but except stone complete all as specified and directed.

M&L PCC solid building blocks 10 cm thick type B1 1:2:4 set in cement mortar (1:6) complete all as specified and directed.

Extra over squared rubble stone walling Jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:4 over stone masonary surfaces incl finishing the surface fair & rough to receive tiling etc complete all as specified and directed.

M&L for glazed colour ceramic tiles of size 300 x450 x 7 mm /250x350x7mm, laid in vertical surface dado/skirting joint free etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specied and directed.

M/L for 20mm thick cement concrete type B-0 1:2:4 (using 12.5 mm graded crushed stone aggregate) complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles joint less 7 to 8 mm thick area of each tiles exceeding 0.18 Sqm but n.exc. 0.38 sqm in floor etc set jointed in neat cement slurry and pointed in white or coloured cement to match the shade.including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per Item no 17 above but skirting including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L non skid / mat finish ceramic colour tiles of size 300 mm x 300 mm x 7 mm, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&Lfor light shade Vitrified Ceramic tiles 12-15 mm thick (square/ rectagular) polished, area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

All as per item No 20 above but dado/skirting includig 10 mm thick rendering in CM 1:4 complete.

M&L for 15mm thick screed bed or bedding layer in CM 1:6 floor finished even & rough to receive tiling/floor finish complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

M & L 18 to 20 mm thick machine cut Kota stone slab flooring , over screed bed base ,laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing icluding 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M & L 18 to 20 mm thick machine cut Kota stone in riser of steps, skirting, dado and piller laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing including 10 mm thick rendering in cement mortor 1:6 complete all as specified and directed.

M & L 18 to 20 mm thick machine cut Kota stone in self and other places etc laid and jointed with grey cement slurry mixed with pigment to match with shade of slab including rubbing and polishing complete all as specified and directed.

M&L for 15-18 mm thick telephone black shade granite stone machine cut mirror polished best quality as per sample laid over 15 mm thick screeding in CM1:4 incl rounding of the edges & providing suitable dia hole in the slab for the gas pipe complete all as specified & directed.

Rounding to edges of stone slabs one edge such as in steps, cooking plateformm and other similar situations complete all as specified and directed.

Taking down existing cement plaster including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L Rendering 10 mm thick CM (1:3) on concrete surfaces on ceiling / facia /RCC Chhaja etc all as directed & finished even & smooth complete all as specified & directed.

M&L for 15mm thick rendering in CM 1:6 finished even and smooth without extra cement on stone wall surface complete all as specified & directed.

M&L for 15mm thick rendering in CM 1:6 finished even and smooth without extra cement on brick or concrete surface complete all as specified & directed.

Racking out joints/pointing to square rubble masonry Jodhpur type regular coursed built in cement mortar all as specified

M&L for Keyed pointing to square rubble masonry Jodhpur type regular course in CM 1:3 all as specified.

M&L for Flush pointing to square rubble masonry Jodhpur type regular course in CM 1:3 all as specified.

M&L preperartion of newly plastered surfaces on wall and applying two coat of wall putty with fair finished and even surface and applying two coat of oil bound distemper complete all as specified & directed.

M&L preperartion of newly plastered surfaces of wall and applying two coat of wall putty with fair finished and even surface and applying two coat of plastic emulsion paint complete all as specified & directed.

Material and labour for complete removal of existing distempered surfaces of walls and applying two coats of oil emulsion distemper of white shade or other approved shade over two coat of birla white putti on plastered surface all as specified and directed.

M & L three coats of white wash on newly plastered surface of wall including preparation of surfaces complete all as specified and directed..

M & L three coats of white wash on newly plastered surface of ceiling including preparation of serfaces complete all as specified and directed.

M & L one coats of white wash on old surface of wall complete all as specified and directed..

M & L one coats of white wash on old surface of ceiling complete all as specified and directed.

Preparation of old plastered or un- plastered surfaces of wall by Brooming down or steel wire brushing, scrapping down mass and efflorescent salts and trading oil & greasy spots, washing rubbing down and stopping surfaces and applying two coat of cement base paint (snowcem) of approved quality & tint complete all as specified and directed.

M & L applying two coats of synthetic enamel paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and directed.

M & L applying two coats of synthetic enamel paint on steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of surfaces completeall as specified and directed.

Taking down chowkhats or frames not exc 1.5 sqm each without taking off shutter from the frame complete all as specified and directed.

Taking down chowkhats or frame exc 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

M&L for Pressed steel frames for doors size 165x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed

M&L for Pressed steel frames for doors size 125x60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed

M & L for mild steel framed work as in brackets etc for coller stands etc framed steps/stairs etc complete using MS angle iron Steel bars gusset plate etc complete all as specified & directed .

Supply and fabrication of Mild steel guard bars and welded to window frames all as specified.

Demiolition of reinforced cement concrete of staircase, landing, chajjas and similar suspended work of any description and any position not otherwise

Dismantling of stone slabs of any description or any thickness in floors, roof etc laid bedded and dry complete all as specified and directed.

M&L sand stone slabs in sunshades, chajjas, shelves, cills, landings cover stones templates etc n exc 2m in length punched dressed on face and along exposed edges self faced on other side and set and pointed in cement mortar 1:4 thickness of slab 5cm complete

M&L for Jodhpur stone roof slabs self faced 7.5cm to 10cm thick , 25cm to 35cm wide ,hoisted and set jointed and grouted in cm 1:3 complete all as specified & directed.

S&F mild steel frame work as in stairs ,hand rails half round or other stock section or section or core for wooden hand rail straidgt portion drilled and countershunk for balusters running bars for doors balusters nosing to steps including embeded in concrete and screwing etc hid ties for foof including securing bolts post and struts in fencing including securing bolts post and struts in fencing including cutting tops to shape as directed drilling holes nothing for wire etc flat iron fillet for necessary drilling boltinh or riveting etc and similar work confirming to Fe 410-0 or fe 310-0

M &L for fabrication of pressed steel cupboard shutters using 1.00 mm thick MS plain sheet & with frame 1.25 MM thick bent to shape incl two coats of syn enamel paint on int surfaces & two coats of hammer tone finish on external surfaces alongwith locking arrangement mortice lock handle etc complete all specified and directed.

S & F 35mm thick factory made second class hardwood glazed and Skelton door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-1991 section 8 clause 8.24 (a) and as directed.

S&F prelaminated flush shutters 35 mm thick, solid core construction and plywood face panels, both face is covered with decorative face veneer with lipping/frame to match.

S/F of 35mm thick factory made partly glazed and partly skeleton shutters, open rebated and prepared to receive wire gauze etc, edge of framing shall be plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc complete all as specified and directed.

S/F of factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made of MS tubes for top & bottom rail. MS frame shall be covered with heat moulded plain color pvc ‘C’ channel having a pvc sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain color pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted to the MS Frame/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, all as specified.

M/L for solid PVC door frame of size 50x47mm made out of 5mm thick pvc sheet reinforced with MS square tube all as specified.

Mild steel black sheet 1mm thick as in covering to door shutter cut to size, edges beaded if directed, hole punched incl round headed screws incl beading turning up metred angle, stopped ends etc complete all as specified and directed.

Taking down steel window/ventilator complete.

Factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer (with or without coller opening) complete all as specified and directed.

Factory made box type steel window with pintol hinges & 2 Nos 150mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer (with or without coller opening) complete all as specified and directed.

Factory made box type steel ventilator with glazing bars dovetailed or welded with one shop coat of zinc chromate primer all as specified.

Factory made box type steel ventilator without glazing bars dovetailed or welded with one shop coat of zinc chromate primer all as specified.

S/F of aluminium anodized,tower bolt 200 mm long complete all as specified and directed.

S&F aluminum anodised handle extruded section of size 150mm long complete all as specified and directed.

S/F of aluminium alloy anodised sliding door bolt woth hasp and stalpe (bolt type and fixings clips of sheet cast or extruded sections and fixings bolts and sliding bolts of extruded sections and fixed 16mm dia and 300mm long complete all as specified and directed.

S &F of mild steel butt hinges 100 mm size complete all as specified and directed.

S&F 100mm size single action door spring hinge complete all as specified and directed.

S & F floor door stopper of alluminium alloy body and toungue anodised with hard drawn steel spring 40mm long complete all as specified and directed.

S/F of 4 mm thick pinheaded sheet glass panes of size not. exceeding 0.5 Sqm fixed with oil putty complete all as specified and directed.

S/F for 3 mm thick plain glass ordinary quality & glazing complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperature 1.00 mm with necessary fitting on steel/ wooden surface complete all as specified and directed.

M/L for PCC 1:2:4 type B1 Mix using 20mm graded stone aggregate as in hold fast iron fixing including necessary form work all as specified.

S&F flat iron for hold fast and similar work confirming to Fe-290 Gde-E-165 fixed with welding and necessary item complete all as specified and directed.

Supply and fixing in repairs decorative type curtain rod stainless steel finish MS pipe 22 to 25 mm dia as per sample superior quality complete

Supply and fixing of purpose made brackets trade pattern for decorative type curtain rods suitable for holding 22 to 25 mm dia as per sample as in repairs.

Supply and fixing of decorative fincals (round type with mirror optic finish) trade pattern for decorative type curtain rods suitable for 22 to 25 mm dia curtain rods as per sample as in repairs

M&L for powder coated Anodised aluminium frame for doors, windows , ventilators, partition, shutters with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed by Engr in charge.

Supply and fix rubber beading complete all as specified.

S & F Door closer hydraulically regulated, Aluminium (extruded section) body designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg fixed complete all as speciied.

S&F brass body 2 levers mortice lock vertical type size 100 mm for aluminium door (as per sample) complete all as specified and directed.

S&F solid PVC wall lining consisting of 5mm thick wood grain printed PVC sheet including solvent cement and PVC frame complete all as specified and directed.

M&L powder coated anodised aluminium shutter for door including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, screws etc. complete all as specified.

M&L for fabrication of glazed windows/louvered ventilators etc using powder coated anodised aluminium sections for frames with or without rebate for hinged/sliding windows (two track/three track), ventilators etc with louveres having suitable mechanism for tilting, U shaped fillets for securing jalies etc & the likes & fixed in position complete all as directed. Note : Glass panes & aluminium wiremesh shall be measured & paid for seperately.

S&F powder coated anodised aluminium deco grill as per sample fixed to aluminium frame work of windows & ventilators.

S&F aluminium alloy wire cloth 0.35 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with aluminium wire staples complete all as specified and directed.

Dismantling of wall and ceiling board ( fiber , pulp , insulation , etc ) or insulation ,etc.) or insulation board/ slabs/ blankes , any thickness including over fillig.

S&F 8 mm thick PVC laminated gypsum board false ceiling size 595x595mm of relevant IS with powder coated aluminium snap grid of size (600 x 600 mm) by fixing of hanger 6 mm dia GI ( up to 2000 mm length) adjusting level fix to roof slab by means of ceiling cleats made out of GI flat 40x3 mm size 60 mm long complete all as spacified

S&F Precast cement concrete post of size 60cm long 100mmx100mm, 1:2:4 Type B-1 fixed in CM 1:4 with grooves for fixing of RCC jali.

Providing pre cast cement concrete louvres and jali, 35mm thick ( measured solid) incld all moulding, excluding frame, PCC 1:2:4 type B-0 (12.5mm graded agg ) set in CM 1:4 complete all as specified

S&F MS with PVC coated decorative 25mm curtain rod with fixing brackets, knob etc as in repairs complete all as specified and directed.

S&F in repair shelf of PTMT fixed with and including chromium plated brass screws and wooden cleats (Min weight 300 gms)

S&F in repair soap dish of PTMT fixed with screws complete all as specified and directed.

S&F in repair PTMT towel rail 450mm long fiexd to wall with chromium plated brass screws and woodn cleats Min weight 170gms approved make complete all as spcified and directed.

S&F bath cabinet of PTMT fixed with and including chromium plated brass screws and wooden claeats size 355mmx455 .

S&F in repair MS chromium plated peg set of five fixing with wall complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarfwall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x160mm as in repair

S&F as in repairs of vitreous china clay water closet squatting pan ORISSA Pattern size 580x 440 mm white with integral foot rest incl 'P' or 'S' traps, flush pipe of 32mm dia HDPE pipe etc all as specified & directed.

S & F as in repairs vitreous china wash down water closet Anglo Indian Type pedestal pattern with seat & cover as in repairs with jet spray complete incl fixing of flush pipe etc complete all as specified and directed.

S & F in repair Vitrous china wash basin as in repairs, white flat back size 450x300 mm including , waste pipe, MS brackets complete all as specified and directed.

S&F PVC connections of 15mm size with PTMT nuts of 600mm long complete all as specified and directed.

S&F chromium plated waste coupling size 32mm full threaded

S&F health faucet with hook and flexible tube

S&F two piece EWC snow white with soft close seat cover, cistern, twin flush fitting including accessories set

S&F wash basin snow white with full pedestal and fixing accessories set

S & F chromium plated fancy type quarter turn 15 mm bore angle cock

S & F chromium plated fancy type quarter turn 15 mm bore bib cock

S & F chromium plated fancy type quarter turn 15 mm bore pillar cock

S & F chromium plated fancy type quarter turn 15 mm bore concealed stop cock

S&F chromium plated towel ring

S&F chromium plated soap dish

S&F chromium plated toilet paper holder

S&F glass shelf with CP frame of size 600 x 150 mm toughed glass complete all as specified and as directed.

S & F butt hinges 100mm, extruded brass, with mild steel hinge pin, bright polished and fixed, type B-21 for PVC door complete all as specified and directed

S&F Cast iron nahani trap with CP grating out let diameter 75mm including jointing to waste pipe fixed in cement mortar 1:1 complete all as specified.

S & F in repair brass chromium plated towel rail 20 mm outer dia `D’ type, 60 cm long between flanges with and including chromium plated brass screws and wooden / plastic cleats, complete all as specified and directed.

S&F CP Wal mixture 3-in-1 system includinjg 1.50 mtr long tele shower and overhead shower of size 150mmx150mm

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 110mm bore as directed

Dismantling of cast iron or AC drain pipe/ PVC pipe jointed in cement mortar of size 75mm bore as directed

S&F 100 mm dia Cast soil waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and directed

S&F 75 mm dia Cast soil waste and vent pipes in any length with or without ears with cement joints laid in trenches or in floor complete all as specified and directed

S&F 100 mm dia Cast soil waste and vent pipes in any length with or without ears with cement joints fixed on wall complete all as specified and directed

S&F 75 mm dia Cast soil waste and vent pipes in any length with or without ears with cement joints fixed on wall complete all as specified and directed

S&F100 mm CI branch pieces single socketed Y equal or unequal complete all as specieied and directed.

S&F 75 mm CI branch pieces single socketed Y equal or unequal complete all as specieied and directed.

S&F100mm CI bends any radius complete all as specified and directed

S&F 75 mm dia CI bend with oval acess door fixed to pipe complete all as specified and directed.

S&F 100mm dia CI vent cowl fixed to pipe complete all as specified and directed.

S&F 75 mm dia CI floor trap plain grating including jointing with solvent cement 75mm dia

S & F in repair of chromium plated shower rose 100mm dia round shape complete all as specified and directed.

S&F in repair chromium plated 15mm dia pillar cock long neck with aerator complete

S &F in repair 25 mm dia stop valves, cast copper alloy with screw down high pressure with crutch or butter fly handle screw both ends for iron pipe or for union & fixed of 25mm dia all as specified specified.

S & F as in repairs 15 mm dia angular stop cock with chromium plated long thread with flange complete

S & F as in repairs 15 mm dia two way angular stop cock with chromium plated long thread with flange complete

S& F as in repairs 15 mm dia stop cock regular body with adujstable wall flange with chromium plated with (concealed type) all as specified

S/F as in repairs of 15 mm dia bib, cock long body with flange with chromium plated fixed with iron pipe complete all as specified and directed.

Supply & Fixing low level flusing cistern PVC 10 ltrs capacity with float valves (ISI Marked) white with inlet ball valve including float and includign pvc connection complete

Dismantling water tanks of capacity exc 250 ltrs but.nexc 500 ltrs and removing to store all as specified.

S&F rotational moulded polythene water storage tanks (cylindrical vertical with closed top hoisted and fixed in position all as specified in SSR Part -I capacity of tank 500 ltrs including tank led cover complete with fixing arrangement complete all as specified and directed.

S & F 20mm dia Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

S& F in repair 750 X 600 X 200 mm thick Stainless steel Plate Racks complete.

Taking out from position framed woodwork as in cupboards/cabinets etc with all fittings ,shutters, shelves, drawers etc in any position fixed in walls or floors & removal of the rubbish outside MD land all as directed at site for overall sizes exc 0.50 sqm but nexc 4.00 sqm & depth n.exc 60 cm complete.

Providing and fixing polyvinyl chloride (PVC) sheet frame of width 150 mm & 18 mm thickness made out of extruded 18mm PVC sheet and joined with suitable Cement Solvent adhesive and screw.The frame shall be fixed to the wall using 75mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 3 Nos. of screws to be provided for each vertical member & minimum 2 Nos. for horizontal member etc. complete as per manufacturers specification and direction of Engineer-in-Charge.

M&L for 18 mm thick solid PVC sheet UPVC Coated Celuka printed in one of two different colours( with wood grain printed pattern /ivory clour finish) as in kitchen cabinet shutters ,all round body of cabinets , shelves ,drawers etc cut to required size jointed with solvent cement & steel screws etc complete all as specified & directed .

Extra over solid PVC sheet for fixing 18 mm width & 2-3 mm thick PVC coloured lipping of approved design & colour fixed with solvent cement or headless nails complete all as directed & specified .

S&F 0 degree clip type self closing hinges for cabinets fixed with cadimum coated screws all as per sample.

S&F 100mm size bright finished cromium plated steel handle of approved shape & design fixed with cadmium coated screws on the kitchen cabint shutters

M&L 50 mm thick PCC (1:2:4)Type B-1 using 20 mm graded stone aggregate for water tank plinth all as specified and directed.

S&F magnetic catches for cabinets of size 50 mm complete with striking plate & magnetic stud complete all as per approved smaple.

Providing precast RCC using 20mm graded aggregate as in cover slab for man hloes set in CM 1:6

M&L for TMT bars 6 to 8mm dia and over, cut to length , bent to shape required including cranking, bending & binding with MS wire (annealed ) not less than 0.9mm dia or securing with clips, as in stirrups also & all as specified.

Writing letters or figures (Black Roman, Italic or Indian n. exc 30cm high with thick paint complete all as specified

Taking down or up steel tubing and connection including cleaning for refixing or removal to store (a) 25 mm dia

All as per Srl Item No 160 above but (b) 20 mm dia

All as per Srl Item No 160 above but (c) 15 mm dia

S/F of water tubing, medium grade, galvanized, with all fittings fixed to wall all as specified (a) 25 mm dia,

All as per Srl Item No 163 above but 20 mm dia

All as per Srl Item No 163 above but 15 mm dia including cutting chases, pinning in & making good to disturbed portion to match the existing surface etc complete.

Excavation in trenches for fdn n.exc 1.5m wide and n.exc 1.5m in depth & getting out in soft /loose soil

Returning filling in including spreading ,levelling,watering and well ramming in layers not exc 25cm

Removing excavated at a level n.exc 1.5 m above the starting point

M & L for cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate for 150 mm dia pipe complete all as specified and directed.

Supply & laying jointing and testing 150mm bore reinfirced conctete pipes class NP-2 laid and jointed in cement mortor 1:1 complete with collars or socket/spigot type laid jointed and haunching at side in cement complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required

Taking down existing old tar-felt from RCC roof, stone and other treatment (brick bat coba) etc. carefully including cleaning roof surface by wire or coir brush and removing all grits ,stone,fungus,moss and finnaly washing down with water to the entire satisfaction of E in charge and removing debrish and rubbish out of the premises to a distance exc. 1.0 km but not exc 2.5 Km complete all as specified and directed.

Material and labour for providing cement concrete (1:2:4) type BO using 12.5mm graded crushed stone aggregate as over roof for making good depression/undulation to make the existing as filling in depression of roof slab complete all as specified and directed.

M&L for PCC 1 : 2 : 4 type B0 using 12.5 mm graded stone aggregate as in roof kerb including weathering, slightly rounded or chamfered angles and throating, as directed etc

M& L for roof treatment in the following stages :- (a) first Course : M&L for 10 mm thick plaster with CM 1:3 mixed with water proofing compound as per manufacturee instructions (Note: - WPC shall be measured and paid separately) (b) Second Course : One coat of bitumen primer T-10/polymerised confirming to IS 3384 @ 0.30 ltr/Sqm (c) Third Course : One coat of Bininding material using blown type bitumen conforming to IS 702 grade 85/25 @ 1.20 Kg/Sqm (d) Fourth Course : A layer of APP membrane polymeric membrane centre core of 100 micron HMHDPE outer film 20 micron each, thickness 2 mm having weigh 3.00Kg/Sqm (e) Fifth Course : A coat of bonding materail using blown type bitumn conforming to IS-702 of grade 85/25 @ 1.20 Kg/Sqm (f) Sixth Course :40mm thick PCC 1:2:4 padding, well compacted using 20 mm graded aggreegatel with grooves shall not be exceeding 1.40 Sqm.

Supply only Integral water proofing compund

Taking down carefully copper/aluminium point wiring for light, fan, bell socket power slocket etc complete with boards, outlet boxes fittings and fixtures such as switchs, sockets, lamp holders bracket, ceiling rose etc complete

Point wiring complete with 1.5 sqmm, single core, multi stranded, copper conductor, PVC (FRLS), insulated, unsheathed cable, confirming to IS-694, 1100 volts grade, ISI marked (class V conductor), in and including PVC concealed conduit (MMS), ISI marked not less than 20mm, with accessories fixed on surface of wall/roof/ceiling etc and including sunken pressed steel terminal boxes in wall but including 3mm thick plastic laminated sheet top cover (ISI marked hylem sheet and 1.50 sqmm PVC insulated unsheathed stranded copper conductor for common earth and connecting to earth dolly material and labour for :- (a) One light point controlled by one, one way switch

All as per Srl Item No 178 above but One fan /Exhaust fan, point controlled by one way switch through regulator.

All as per Srl Item No 178 above but One socket outlet 3 pin 6 Amps on same board

All as per Srl Item No 178 above but One socket outlet 3 pin 6 Amp on independent board

All as per Srl Item No 178 above but One bell point controlled by one bell push.

All as per Srl Item No 178 above but One light point controlled by two , two way switches.

All as per Srl Item No 178 above but with 2.5 Sq mm single core multistanded copper conductor cable for 3 pin 16 Amp socket outlet on independent board .

S&F switch flush type single pole one way 6 Amp ISI Marked

S&F switch flush type single pole one way 16 Amp ISI Marked.

S&F socket out let , 5 pin , 6 Amp FT.

S&F socket out let , 5/6 pin ,16 Amp FT. ISI Marked

S & F switch Piano flush type single pole two way 6 Amp ISI Marked.

S & F bell Push, piano flush type 6 Amp ISI Marked

S&F bell Ding Dong, AC 230 Volts, Single Pole

supply and fix socketed stepped type electonic fan regulator flush type , ISI Marked.

S & F Ceiling rose, 3 terminal/PVC/ polycarbonate, isolated body

S&F LED tube light fitting Box type 20 watt complete with all accessories such as bipin holders connector block, etc internally pre-wired , including LED lamp-1No, connectiong up with , multistranded copper conductor of size 1.00 sq mm flexible cable

S&F insulated Batton lamp holder metal cased body of brass with back plate suitable for batton fittings including 9 watt LED Lamps ISI Marked.

Supply and fix LED bulk head light 8/10 watt

S&F connecting, and commissioning of street light fitting 30/45 watt LED , IP-65 protection, single peice pressure dia cast aluminium alloy housing high grade powder coated finish with heat resistant toughned clear glass cover for lamp and contror gear compartment with high voltage surge protection device upto 4.5 KV, Prewired including 1.60 mtr long 40mm bore light grade GI pipe mounting bracket made to shape with and including MS clamp of F1 40 mmx6mm with bolts , nuts & washers and conductor to fitting with 3 core 1.5 sqmm pvc insulated cable complete all as specified

M/L in repairs sub main wiring with 6.00 Sq mm single core multistrandred copper conductor PVC insulated and unsheathed cable passing through PVC concealed conduit and making good the distrurbed surface of wall inc 6 Sq mm single core copper conductor cable PVC insulated and unsheathed cable as earth wire. Note :- Two runs of cable 6 Sqmm and One run of 6 Sqmm shall be measured as unit length.

S&F Prewired distribution board in sheet metal with 200 Amps rated copper bus bar Confirming to relevant IS.SPN 8 way, Note -Rate are deemed to be included for flashing in wall concealed complete, making good and matching existing surface.

S&F Prewired distribution board in sheet metal Prewired when MCB to be used with 200 Amps rated copper bus bar Confirming to relevant IS TPN 4 way, Note -Rate are deemed to be included for flashing in wall concealed complete, making good and matching existing surface.

S&F MCB Single pole 5 to 30 Amp, 10 kA, ISI Marked.

S&F MCB Double pole RCBO 40 Amp, 100mA, ISI Marked.

S&F MCB SPN 63 Amp, 10 kA, ISI Marked.

S & F TPN 63 Amp MCB 10 KA ISI marked.

Fixing and hanging only ceiling fan/ Exhaust fan and connectiong up includisng provison of cable from ceiling rose or connector to fan.

Taking down serviceable/Unserviceable , existing Electric Meter Any Capacity and Refixing in same position after completion of B/R work NOTE : The rates are deemed to be included for providing suitable electric connection at incoming and out going - 4 Nos).

Earthing complete with galvanised steel earth plate electrode 60 x60cm x 6 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) wih top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in elevtrical plate no. 3 connected to Earthing test point all as specified or indicated including testing on completion Note : (i) Rates are deemed to be included for necessry earth work ,PCC pit , RCC cover etc complete. (ii) Earth lead shall be up to 7.5 Mtr and rates are deemed to be included for GI pipe 15mm Light grade upto 7.5 mtrs for protection of earth wire 4.0 mm dia.

Supply and laying or fixing or passing through pipe 1100volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanised steel wire and overall PVC Sheathed 16 sq 4 core in service connection.

M/S Dharam Chand Lal Chand Jain