ESTABLISHMENT OF INSTITUTE FOR ORGAN AND TISSUE TRANSPLANT, CHEVAYUR, KOZHIKODE - CONSTRUCTION OF DERMATOLOGY HOSPITAL AND ITS ALLIED FACILITIES

CIVIL WORKS

PLUMBING WORKS

ELECTRICAL WORKS

ELV WORKS

FIRE FIGHTING

STP (50 KLD)

BUILDING SIGNAGES

DSR/ MORTH CODE

Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil

Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials. All kinds of soil 1.5 to 3mtr

Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50m: All kinds of soil. Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

Filling with contractor own earth (excluding rock) in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

Providing and injecting chemical emulsion for Pre-Constructional Anti termite treatment and creating a chemical barrier on top surface of plinth filling, junctions of inside walls and floors, soil along external perimetre using the chemical lmidacloprid emulsifiable (IS 6313: part 2:2013) 30.5% SC mixed with water in 1:499 ratio. The emulsion is spread at 5litre/sqm on top surface of plinth filling,at 1 litre/linear metre along the junction of wall and floor and at 2.25litres/linear metre of the plinth wall as per the specifications and directions. (Note: plinth area only shall be measured for payment). The product performance shall carry guarantee for 10 years.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks,plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc

Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases)

Centering and shuttering including strutting, etc. and removal of form for: Edges of slabs and breaks in floors and wallsUnder 20 cm wide

Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges.

Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Providing, hoisting and fixing up to floor level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but excluding cost of reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone - III) : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo - Mechanically Treated bars of grade Fe-500D or more

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Excess or less cement used as per design mix is not payable or recoverable separately. In case the cement content in design mix is more than the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All work upto plinth level. Concrete of M30 grade with minimum cement content of 350 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Excess or less cement used as per design mix is not payable or recoverable separately. In case the cement content in design mix is more than the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All work above plinth level upto floor V level. Concrete of M30 grade with minimum cement content of 350 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Excess or less cement used as per design mix is not payable or recoverable separately. In case the cement content in design mix is more than the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All work up to plinth level. Concrete of M25 grade with minimum cement content of 330 kg /cum

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Excess or less cement used as per design mix is not payable or recoverable separately. In case the cement content in design mix is more than the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. All work above plinth level upto floor V level. Concrete of M25 grade with minimum cement content of 330 kg /cum

Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete

Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc.complete

Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level thickness 20cm and above in : CM 1:6 ( 1 cement : 6 coarse sand sand) etc complete

Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for super structure above floor two level upto floor five level with thickness 10cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

Granite cladding (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. 18mm thick granite of any colour and shade

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge. Granite work

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints with epoxy grout. (Grouting shall be paid separately). Size of tile : 300 x 600mm

Providing and laying Heavy duty Homogenous matt finish vitrified tiles in floor of thickness not less than 16mm(thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20mm thick cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with epoxy grout and matching pigments etc., complete. (Grouting shall be paid separately) . Heavy Duty vitrified floor tiles matt finish : Size of Tile 600 x 600 mm

Providing and laying Exterior grade Matt finished vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorptions less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate)finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.40 mm thick with 20 mm nominal size stone aggregate

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturers specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement: 18 mm thick

Chequerred precast cement concrete tiles 22 mm thick in floors, footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse sand).Dark shade pigment using ordinary cement

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm

Providing and laying rectified Anti skid glazed Ceramic tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand)including grouting the joints with epoxy grout and matching pigments etc., complete. (Grouting shall be paid extra) . Size of Tile 300x300mm

Grouting the joints of flooring/wall tiles (any size) having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent

Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross T of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.

Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross T of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge

Providing and fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flanged of cleat fixed to the angle hangers of 25x10x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45x15x0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5 mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27 mm high having flages of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of

12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand)

6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand)

Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) : Flush/ Ruled pointing

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. 13 to 16m

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

Finishing walls with textured exterior pint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Cement plaster 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers.

Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement.12 mm cement plaster including providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.80x1.25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters

Extra for providing grilled rolling shutters manufactured out of 8 mm dia M.S. bar instead of laths as per design approved by Engineer -in-Charges, (area of grill to be measured).

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

Providing and fixing circular / hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing .

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In stringers, treads,landings etc. of stair cases, including use of chequered plate wherever required, all complete

Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.G.I. pipes

Providing and fixing G.I. louvers of approved size and gauge, including cutting, hoisting and fixing in position, fixed to vertical members of approved size, with welding and/or bolting using special shaped washers, nuts and bolts, and applying one coat of approved steel primer to exposed steel surfaces, complete as per directions of Engineer-in-Charge.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing and paneling to be paid for separately): For fixed portion. Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

Providing and fixing 4mm thick ACP sheet in panelling fixed in aluminum doors,windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 6 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 8 mm thickness (weight not less than 20 kg/sqm)

Providing and fixing Toughened glass in upvc/aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item): 6mm thick toughened glass

Providing and fixing Toughened glass in upvc/aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item): 8mm thick toughened glass

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).Second class teak wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately). Second class teak wood .35 mm thick shutters

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Second class teak wood

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete:100x60x2.50 mm

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non- decorative Type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for Providing and fixing flush doors with decorative veneering instead of non decorative ISI marked flush door shutters conforming to I.S. 2202 ( part I)On one side only

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded ) (overall area of door shutter to be measured): Rectangular or square

Finishing wood work with Melamine polish with thinner (30%) : New work (Two or more coat applied @ 2.2 ltr/10 sqm) over and including two coats of melamine sealer with thinner (30%) @ 2.2 ltr/10 sqm and wood filler wherever required all complete as per the direction of engineer in charge

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters ( Total area of the shutter to be measured).

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete:250x10 mm

Providing and fixing bright finished brass 100 mm mortice latch with one dead bolt and a pair of lever handles of approved quality with necessary screws etc. complete

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ wooden frames with rawl plugs screws etc

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:250x10 mm

Providing and fixing Brass100 mm mortice latch and lock with 6 levers without pair of handles ( best make of approved quality ) for aluminum doors including necessary cutting and making good etc. complete

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors, embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer -in-Charge.With stainless steel cover plate minimum 1.25 mm thickness

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of crosssection 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing to existing door frames.30 mm thick Fiberglass Reinforced Plastic (F.R.P) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF) / Polystyrene foam to be used all filler material throughout the hollow panel, casted monoolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS : 14856, complete as per direction of Engineer-in-charge.

Supplying and fixing 300 mm Aluminium aldrop

Providing and fixing factory made uPVC white colour casement /casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/-0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 +/- 0.2mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 +/- 0.2 mm and single glazing bead of appropriate dimension.(Area of window above 0.75 sqm upto 1.50 sqm).

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with top fixed with S.S. friction hinges (350 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. ( Area of window upto 2.50 sqm).

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/-0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Casement window single panel with S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash 67 x 80 mm both having wall thickness of 2.3 +/- 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 0.75 sqm.)

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/-0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window double panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Casement window three panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 1.50 sqm).

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 +/- 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Casement window four panels with S.S. friction hinges (350 x 19 x 1.9 mm) made of (big series)frame 67 x 60 mm & sash / mullion 67 x 80 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of window above 2.50 sqm).

Providing and fixing stainless steel (SS 304 grade) adjustable friction window stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer - in-Charge complete.355 x 19 mm

Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary necessary screws etc. complete.Powder coated minimum thickness 50 micron aluminium

Providing and Placing in position suitable PVC water stops conforming to IS : 12200 for construction / expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete:Serrated with central bulb ( 225 mm wide, 8-11 mm thick)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and fixing 12 mm thick frameless toughened glass door shutter and fixed glass partition of approved brand and manufacture including patch fittings, and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer in-charge (Door handle, lock and heavy duty floor spring etc.to be paid separately)

Providing and fixing ISI marked fire rated GI Sheet doors conforming to FD 120-UD classification of IS 3614 :2021 with fire rating of 120 minutes integrity only. The factory manufactured door frame and shutter assembly shall be made out of minimum 1.50 mm thick GI Sheet with minimum 120 g/m2 coating as per IS: 277. The Door should be finished with powder coating in standard RAL shade finish having DFT of minimum 50 microns. The door should carry a minimum 500 Hrs of salt spray test. All accessesories like hardware, vision panel, fire smoke seal etc to be supplied by Fire door manufacturer only as per the guidelines laid down in IS 3614:2021. Every door must be ISI labeled confirming to type of door & its fire rating. The offered door must carry a prior valid test evidence of 5 years from CBRIRoorkee. No fresh testing is required within the validity of test report from CBRI Roorkee.The Door frame shall be single rebate grooved profile to accomodate 10x4mm Fire Seal, Size of Frame to be minimum 125mm x 55mm made out of minimum 1.50mm thick galvanized steel sheet. Frames shall be butt/ mitered joint and field assembeled with bolting system. The frame should also be provided with fire rated smoke seal as per IS: 3614:2021 or as per test evidence. It shall be pasted on surface and perimeter of main frame. All provisions should be mortised & provided with necessary inbuilt reinforcement to receieve appropriate hardware. Frames should be provided with back plate bracket for anchor fastner with 8-10 mm dia and minimum 80 mm long HDG fasteners, with Polyamide sleeves for installation of frame in finished plastered masonary wall opening.

Providing and fixing ISI marked fire rated GI Sheet doors conforming to FD 120-UD classification of IS 3614 :2021 with fire rating of 120 minutes integrity only. The factory manufactured door frame and shutter assembly shall be made out of minimum 1.50 mm thick GI Sheet with minimum 120 g/m2 coating as per IS: 277. The Door should be finished with powder coating in standard RAL shade finish having DFT of minimum 50 microns. The door should carry a minimum 500 Hrs of salt spray test. All accessesories like hardware, vision panel, fire smoke seal etc to be supplied by Fire door manufacturer only as per the guidelines laid down in IS 3614:2021. Every door must be ISI labeled confirming to type of door & its fire rating. The offered door must carry a prior valid test evidence of 5 years from CBRIRoorkee. No fresh testing is required within the validity of test report from CBRI Roorkee.The Door frame shall be single rebate grooved profile to accomodate 10x4mm Fire Seal, Size of Frame to be minimum 125mm x 55mm made out of minimum 1.50mm thick galvanized steel sheet. Frames shall be butt/ mitered joint and field assembeled with bolting system. The frame should also be provided with fire rated smoke seal as per IS: 3614:2021 or as per test evidence. It shall be pasted on surface and perimeter of main frame. All provisions should be mortised & provided with necessary inbuilt reinforcement to receieve appropriate hardware. Frames should be provided with back plate bracket for anchor fastner with 8-10 mm dia and minimum 80 mm long HDG fasteners, with Polyamide sleeves for installation of frame in finished plastered masonary wall opening

Providing and fixing factory made ISI marked un-insulated metal fire rated doorset assembly for all non egress application areas like shafts etc. consisting galvanized iron steel frame and single leaf shutter including necessary hardware accessories conforming to FD 120 UD classification of IS 3614 :2021 with fire rating of 120 minutes integrity. The door frame and shutter shall be made out of minimum 1.20 mm thick Gl Sheet with minimum 120 GSM Zinc coating as per IS: 277 The entire fire rated doorset assembly shall be tested in unlatched condition as per IS 17518 (Part-1): 2022. Frame: The frame shall be of minimum size 90 x 60 mm with grooved profile to take appropriate fire rated smoke seal, having mitred cut joints (self tab/screwed assembled at site) and provided with appropriate reinforcement suitable for taking hardware and flush fixing as per IS: 4351. The smoke seal material shall be of EPDM tested in accordance with ASTM E-84 of minimum size 10x4 mm, fixed within the inbuilt groove or stuck with adhesive on the entire perimeter of the frame. The door frame shall be fixed in all four sides to masonry wall opening with CSK/Hex headed fasteners of minimum 8 mm dia size and minimum 80 mm long with 8mm dia polyamide sleeves @ 4 number at each on vertical sides (up to 2100 mm height) and 2 numbers each on top and bottom sides.

Providing and mixing integral crystalline admixture for waterproofing treatment to RCC structures like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc.. at the time of transporting of concrete into the drum of the ready-mix truck , using integral crystalline admixture @0.80% (minimum) to the weight of cement content per cubic meter of concrete) or higher as recommended by the manufacturers specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels/ subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerincharge. The product performance shall carry guarantee for 10 years against any leakage.For horizontal surface one coat @1.10 kg per sqm.

Providing and fixing of stainlees steel corner guard of height 1500 mm & 50x50mm wing size, stainless steel of 304 grade with thickness of 1mm with rubber backing 1.5 mm (total thickness 2.5mm) all complete as directed by Engineer-incharge

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg., for doors, including cost of cutting floors , embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge.

Supply of SS corner lock for toughened glass door of 12mm thick with weight up to 200 kg

Supply of stainless steel handle for toughened glass door, H- type of size 450 mm and 25 mm dia with satin finish of reputed make

Supply and fixing of shaft lock with allen key in Aluminium doors for fire shaft, of approved Make all complete, as per the direction of Engineer-in-charge

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steeel bar conforming to IS:1786, having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) Complete as per design

Supply & Installation of SS 304 steel ceiling panels. Total Panel thickness shall be of 30mm. It should be 0.5mm SS304 sandwich (both sides 0.5mm sheet) panel with core consisting of rigid polyurethane foam, which has been injected under high pressure, with a minimum density of 40 kg/m3 .The individual wall panels shall use the tongue and groove technology for joining two panels, no welding should be flush. Steel plate finished to fine grain surface, treated properly to take antifungal paint. Paneling should be easy to maintain, durable, antistatic/conductive and fire retardant. Clearance between ceiling panel and slab ceiling should be sufficient to allow for the installation of accessories like laminair ceiling and peripheral lighting etc. This closed space should be flushed continuously to eliminate dust and bacterial accumulation. The junction should be seamless and should be sealed with suitable sealants.

Wall painting with Anti Bacterial Paint. Filling of all joints and cavities with metallic epoxy filler and sanded flush to provide a jointless finish and spraying with anti bacterial, self sterilizing paint to a d.f.t of 300 microns with primer.

Providing and laying 2mm thick Vinyl flooring in roll form of a width not less than 1.2 m of approved equivalent over prepared existing surface and joined by cord welding to make it seamless, at all levels, as per manufacturers specifications including coving rounded junction between floor & wall. The wear surface shall consist of impregnated polyurethane homogeneous mixture of PVC, Plasticizers,Urethane, color pigments, and filler calendared to form a sheet. Colors and pattern detail shall be dispersed throughout the thickness of the wear layer. The sheet shall conform to the requirements of BS EN 649:1997, “Standard Specification for Vinyl Sheet Floor Covering without backing.” This shall conform to Group P of Wear Resistance as per EN 660-2, Fire Resistance of more than 11kW/m2 as per ISO 9329-1Critical Radiant Flux, Slip resistance of R9 as per Oil Wet Ramp test (AS 4586). Installation:It isimportant to ensure the subfloor on which the sheet is being laid is smooth, flat & hard & free from moisture, grease,etc. In case of uneven subfloor, the same should be leveled by self leveling compound. The moisture level present in the subfloor should be less than 8% before installation of the floor. The sheet should be laid using water based adhesive like SR 998 / Arobond or similar. The installation shall be undertaken as per the manufacturer’s installation instructions. The rate shall include all materials, preparation of the base surface and work at levels etc., complete and as directed. All guarantees provided by the manufacturer are to be passed on to the owner during handover to owner.

Supply, Installation, Testing and Commissioning of manually operated hermetically sealed sliding door of 1800mmx2200mm size with 0.80mm thick Aluminium sheet door profile on both sides having Aluminium door panel 3mm thick & 45mm PUF infill, Glazed vision panel with 5mm clear glass 200x300mm or nearest size with necessary accessories and fittings complying to international standards

Providing &fixing UV Stabilized Poly carbonate compact sheet 4mm thick clear transparent with UV protection treatment weight not less than 4800 GM/SQM. Light transmission of 90%.The masking carrying instruction as to which side UV protected the same side should be installed facing out wards. Fire retardant confirming to IS 14431987,Aluminium 50mm thick leak proof fixing management system, confirming IS 733-1987 alloy 606376 EPDM rubber gaskets, Silicone sealent, cold forged fasteners to be used for fixing the polycarbonate sheeting. EPDM rubber gaskets shall be as per ASTM - D2240 strength ASTM-D412 as approved by the Engineer in charge

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Supplying and fixing C.I with frame for manholes:500 mm diameter C.I. (medium duty) the weight of the cover to be not less than 58 kg

Supplying and fixing C.I with frame for manholes:560 mm diameter ( heavy duty) the weight of the cover to be not less than 108 kg

PVC WEEP HOLES- Providing weep holes using 75mm dia. PVC pipes working pressure 4kg /sq.cm including cost of materials, conveyance, labour charges etc. complete.

Supplying, filling, spreading & leveling with graded metal of size range 20 mm to 63 mm in filter media in required thickness and covered with geotextile of 120gsm for all leads & lifts, all complete as per direction of Engineer-in-charge. size of the media 60x60x120cm

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in open well, in the required thickness, for all leads & lifts, all complete as per direction of Engineer -in- charge

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates,bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work ( Payment shall be made on the cross sectional area of R.C.C. or R.B work) as per direction of Engineer-in-charge.

Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar

Filling available excavated earth open well in all depth in layers and, consolidating each deposited layer by ramming , lead up to 50 m and lift upto 1.5 m

Taking and removing sewage slurry and disposing the same at suitable places out side the premises at contractors own risk including all conveyances and cleaning the septic tank with water etc.complete

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and rerolling the sub grade and disposal of surplus earth with lead upto 50 metres

Providing and laying 60 mm thick factory made cement concrete interlocking paver block of M - 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 ( 1 cement : 3 coarse sand) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge ( length of finished kerb edging shall be measured for payment ). ( Precast C.C. kerb stone shall be approved by Engineer-in-Charge)

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Providing & laying LAWN GRASS - Pearl Grass turf with earth 50mm to 60mm thickness on existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same,with sprinkler and maintenance for 6 months or more till the grass establish properly, as per direction of officer-in-charge

Providing, supplying, transporting, planting, and maintaining healthy Mangifera indica (Mango) plants of 1 m to 1.5 m height in precast reinforced cement concrete rings of minimum 600 mm internal diameter and 300 mm height, including excavation of pits, good quality topsoil mixed with well-decomposed organic manure, proper planting , firming of soil, immediate watering, staking where required, and maintenance for a minimum period of 6 months including watering, weeding, manure application, pest and disease control, and replacement of dead or unhealthy plants, complete as directed by the Engineer-in-charge.

Construction of granular sub-base by providing graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with a motor grader on the prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401 Grading-I - Plant Mix Method

Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density

Providing and laying bituminous macadam with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with bituminous binder (VG 30), transported to site, laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction. For Grading I ( 40 mm nominal size )

Providing and laying bituminous concrete with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with a bituminous binder( NRMB) @ 5.2 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level, and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects For Grading - I ( 19 mm nominal size )

Providing and applying primer coat with bitumen emulsion ( SS) on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 - 1.0 kg/sqm using mechanical means.

Providing and applying tack coat with bitumen emulsion (RS) using emulsion pressure distributor at the rate of 0.25 - 0.30 kg per sqm on the prepared Granular Surface cleaned with mechanical broom

DSR CODE

Providing and fixing floor mounted, white vitreous china pedestial type single peice water closet approved make and size including seat cover, cistern with manually controlled twin flush fittings ,nuts, bolts and gasket etc including making connection with the existing P/S trap, complete in all respect as per directions of Engineer-in Charge.

Providing and fixing white vitreous china manually operated urinal with self closing concealed flush button of approx.size 310X330X585 mm or nearest size having flushing capacity of 1.5 LPF having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer - in-charge.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in Charge and finished smooth. Granite Stone of approved shade

Providing and fixing white vetrious china wash basin of size 630x450 mm or nearest size with C.I. brackets, 15 mm C.P. brass low flow pillar tap including 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required as per the direction of engineer incharge.

Providing and fixing white vetrious china under counter wash basin of size 550X450X190 mm or nearest size with C.I. brackets, 15 mm C.P. brass low flow pillar tap , 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required as per the direction of engineer incharge.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board510x1040 mm bowl depth 250 mm

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gms

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms

Providing and fixing uplasticised PVC connection pipe with brass unions: 45 cm length15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

Providing and fixing PTMT Soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fittings arrangements, weighing not less than 106 gms.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Supplying and fixing CP Towel rod 45cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in charge.

Providing and fixing C.P. brass low flow long body bib cock: 15 mm nominal bore.

Supplying and fixing Low flow Health faucet ABS body with wall hook and 1 metre SS braided rubber hose pipe as per the direction of Engineer in-charge.

Supply and fixing CP brass Low flow bib tap with elbow operation lever (for sink ) with long swivel spout and wall flange in position.

Supply and fixing CP brass low flow surgical sink mixer with elbow operation lever with 190mm longswivel spout , conecting legs and wall flanges in position

Supply and fixing CP brass Low Wall mounted Wall mixer with bend pipe for overhead shower in position.

Providing and fixing low flow over head shower of size 100mm dia round shape ,shower arm in position.with concealed stop trims , concealed stop cock body 20 mm nominal bore.

Supplying, fixing testing and commissioning of horizontal type manual electric storage water heater of 15L capacity

Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 1500x450 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.15 mm nominal dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.25 mm nominal dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.32 mm nominal dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SDR 11) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work Exposed on wall : 15 mm nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SDR 11) pipes, having thermal stability for hot&cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes&fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work - Exposed on wall : 20 mm nominal outer dia .

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SDR 11) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings includingB fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work- Exposed on wall :25 mm nominal outer dia .

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SDR 11) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings includingB fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work- Exposed on wall :32 mm nominal outer dia .Pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SDR 11) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings includingB fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge Internal work/external work- Exposed on wall :40 mm nominal outer dia .Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SDR 11) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings includingB fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work- Exposed on wall :50 mm nominal outer dia .Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :32 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

Providing and fixing Forged brass Air release valve of approved quality (screwed end): 20 mm diameter

Supplying and fixing PVC Floor Trap 100mmx75mm size without Jali including cutting open, boring through RCC slabs and making good the damages

Providing and fixing SS grating of approved quality. Rectangular type with openable circular lid : 150 mm nominal size square 100 mm diameter of the inner hinged round grating

Supply and fixing SWR Type B sanitary concealed pipes and specials , jointing with solvent cement and fixing them on slabs, floors etc. in position for connecting various fixtures (including fixing of pipes in sleeves/ drilled holes before water proofing) and specials with brick or CC supports wherever necessary including cutting and chasing brick walls as required, making good the same with brick in CM 1:6 and plastering with CM 1:4, 12mm thick one coat, sealing joints between pipe and concrete, complete : 110 mm diameter

Supply and fixing SWR Type B sanitary concealed pipes and specials , jointing with solvent cement and fixing them on slabs, floors etc. in position for connecting various fixtures (including fixing of pipes in sleeves/ drilled holes before water proofing) and specials with brick or CC supports wherever necessary including cutting and chasing brick walls as required, making good the same with brick in CM 1:6 and plastering with CM 1:4, 12mm thick one coat, sealing joints between pipe and concrete, complete : 75 mm diamete

"Supply and fixing PVC 10kgf sanitary concealed pipes and specials , jointing with solvent cement and fixing them on slabs, floors etc. in position for connecting various fixtures (including fixing of pipes in sleeves/ drilled holes before water proofing) and specials with brick or CC supports wherever necessary including cutting and chasing brick walls as required, making good the same with brick in CM 1:6 and plastering with CM 1:4, 12mm thick one coat, sealing joints between pipe and concrete, complete : 50 mm diameter"

Supply , jointing and fixing SWR type B Sanitary exposed pipes and specials with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other required materials including drilling holes, making good the walls, cleaning etc. and finishing complete :110 mm diameter

Supply , jointing and fixing SWR type B Sanitary exposed pipes and specials with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other Required materials including drilling holes, making good the walls, cleaning etc. and finishing complete :75 mm diameter

Supply , jointing and fixing 10Kgf exposed pipes and specials with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other required materials including drilling holes, making good the walls, cleaning etc. and finishing complete : 50 mm diameter

Supply , jointing and fixing SWR Type A exposed pipes for vent and specials with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other required materials including drilling holes, making good the walls, cleaning etc. and finishing complete : 75 mm diameter

Supply and Fixing 110mm PVC Ventilation Cowl with wired mesh in position

Supply and Fixing 75mm PVC Ventilation Cowl with wired mesh in position

Supply , jointing and fixing SWR Type A exposed pipes and specials for rain water with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other required materials including drilling holes, making good the walls, cleaning etc. and finishing complete : 110 mm diameter

Supply , jointing and fixing SWR Type A exposed pipes and specials for rain water with good quality solvent cement and teflon tape and fixing the same to line, plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by using slotted rails , U clamps, 8mm threaded rods and other required materials including drilling holes, making good the walls, cleaning etc. and finishing complete : 75 mm diameter

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Constructing masonry shoe to the bottom of the rain water pipes with brick in cement mortar 1:6 over CC 1:4:8 using 40mm metal concrete, plastering the exposed surfaces using CM 1:5 one coat, forming the circular spout outlet, finishing etc. complete. In direction of enginer in charge

Supply and fixing Inline rain water filter suitable for area up to 225sqm or approx equal area having ss304 multi surface screen, 110mm inlet, 75mm clear water outlet and 90mm drain outlet etc

Providing and fixing PVC gully trap (single) with jali, brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 160x100 mm size PVC gully trap

Providing and fixing gun metal ball valve of size 50 mm nominal bore (PN 10), of approved quality with plastic floats complete

Supply and fixing CP brass Low flow sink cock (wall mounted) with long swivel spout and wall flange in position.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Supply, installing, testing and commissioning an automatic OHT water level control system comprising level switches, and relay control panel. The system shall include suitable high and low level switches, and a wall-mounted relay panel with MCB, control relay and auto/manual operation. Complete with all wiring, cabling, accessories, earthing and proper commissioning, finished in all respects as per site requirements and approved makes.

Supplying and fixing (handicaped toilet set) white vetrious china European water closet(6/3), wash basin, 600x100 hingedhand rail-1 nos, 600mm long grab bars-4 nos and all associated accessories like flushing cistern, seat and cover, CP brass elbow operated pillar tap with pressure , waste coupling etc. to make the toilet functional for special need persons including cutting and making good the walls and floor, etc.

Providing and fixing gun metal ball valve of size 40 mm nominal bore (PN 10), of approved quality with plastic floats complete

Supply, installing, testing and commissioning an automatic OHT water level control system comprising level switches, solenoid valve and relay control panel. The system shall include suitable high and low level switches, a normally closed solenoid valve of dia 40 mm, and a wall-mounted relay panel with MCB, control relay and auto/manual operation. Complete with all wiring, cabling, accessories, earthing and proper commissioning, finished in all respects as per site requirements and approved makes.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the center of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms

Supplying and fixing PVC SWR 'P' Trap 100mmx100mm size including fixing through RCC slabs, fixing with drainage pipe and making good the damages

Supply and fixing Mineral reinforced polypropylene hot water resistant sanitary concealed pipes and fittings , jointing with push fit sockets and fixing them on slabs, floors etc. in position for connecting various fixtures (including fixing of pipes in sleeves/ drilled holes before water proofing) and specials with brick or CC supports wherever necessary including cutting and chasing brick walls as required, making good the same with brick in CM 1:6 and plastering with CM 1:4, 12mm thick one coat, sealing joints between pipe and concrete, complete : 110 mm diameter (For kitchen)

Providing and fixing Mineral reinforced polypropylene hot water resistant drainage pipes and fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of with solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 50 mm dia pipe (For kitchen

Supplying and fixing Mineral-reinforced polypropylene Boss pipe (height riser) 100mmx75mmx50mm size including fixing with P trap and making good the damages. (For Kitchen only)

upplying and fixing Mineral-reinforced polypropylene ; Trap 100mmx100mm size including fixing through RCC slabs, fixing with drainage pipe and making good the damages. (For kitchen only

Supply and fixing of CPVC puddle pipe with flange having a length such that there is 30cm and 10cm over hang outside and inside of the tank respectively or as suggested by engineer in charge which ever is greater 50mm inner diameter

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 ( 1 cement : 2 fine sand) including testing of joints etc. complete:250 mm dia R.C. C. Pipe

Supply and Laying 200 diameter UGD SN8 pipes, lowering into trenches, placing in position, aligning to line and levels and jointing with solvent cement including earth work excavation in allclasses of soil, refilling the trenches and transporting excess soil as recommended by the site engineer,complete. (For sewer lines&RWH )

Supply and Laying 160 diameter UGD SN8 pipes, lowering into trenches, placing in position, aligning to line and levels and jointing with solvent cement including earth work excavation in allclasses of soil, refilling the trenches and transporting excess soil as recommended by the site engineer,complete. (For sewer lines&RWH )

Supply and Laying 110 diameter UGD SN8 pipes, lowering into trenches, placing in position, aligning to line and levels and jointing with solvent cement including earth work excavation in allclasses of soil, refilling the trenches and transporting excess soil as recommended by the site engineer,complete. (For sewer lines&RWH )

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand)with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design: Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes Size 90x80 cmWith common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steeel bar conforming to IS:1786, having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) Complete as per design

Supply, Erection, Testing and Commissioning of Horizontal multistage centrifugal pump (Transfer pump) set capable of lifting 189 lpm of water against a total head of 50m - 2 nos (1 working and other standby) with accessories such as 65MM mm non return valve - 2nos, 65mm full way wheel valve - 4nos, pump panel having MCB, digital diaplay of voltage and current, Indicating lamps, manual switches, digital function capable of dry run prevention and automatic interchange system all enclosed within a single panel -, For Domestic water supply to OP BLOCK

Supply, Erection, Testing and Commissioning of Horizontal type multistage centrifugal pump (Transfer pump) set capable of lifting 150 lpm of water against a total head of 50m - 2 nos (1 working and other standby) with accessories such as 50mm non return valve - 2nos, 50mm full way wheel valve - 4nos, pump panel having MCB, digital diaplay of voltage and current, Indicating lamps, manual switches, digital function capable of dry run prevention and automatic interchange system all enclosed within a single panel , For Flushing water and STP to OP Block)

Supply, Erection, Testing and Commissioning of Horizontal type multistage centrifugal pump (Transfer pump) set capable of lifting 135 lpm of water against a total head of 30m - 2 nos (1 working and other standby) with accessories such as 50mm non return valve - 2nos, 65mm full way wheel valve - 4nos, pump panel having MCB, digital diaplay of voltage and current, Indicating lamps, manual switches, digital function capable of dry run prevention and automatic interchange system all enclosed within a single panel .for staff quarters , and sanitorium domestic and flushing water supply )

Supply,Erection, Testing and Commissioning of drainage submersible pump with float switch (Dewatering pump) sets capable of lifting 45lpm of water against a total head of 12m - 1 nos (1 working + standby), accessories such as full way wheel valve 32mm dia 1 nos, non return valve 32mm dia - 1 nos, pump panel having MCB, digital diaplay of voltage and current, Indicating lamps, manual switches allenclosed within a single panel (Dewatering pump in pump room)

;Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SCH 40) pipes, having thermal stability for hot&cold water supply including all CPVC plain&brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes&fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work - Exposed on wall 65mm nominal diameter pipe (For Pumping main - Domestic water to OHT )

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SDR 11) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work - Exposed on wall : (For pumping main from dewatering pump in pump room) 32 mm nominal outer dia .Pipes

Supply and fixing Electromagnetic flow water meter (digital) - of 65mm size, flow indicator totalizer with RS485 modbus output along with MS panel and capable of withstanding 25bar pressure with adaptors, fitting connecting flanges with pipe. (In STP treated water ,flushing, Rain water pumping main to OHT )

Supply and fixing Electromagnetic flow water meter (digital) - of 50mm size, flow indicator totalizer with RS485 modbus output along with MS panel and capable of withstanding 25bar pressure with adaptors, fitting connecting flanges with pipe. (In domestic pumping main to OHT )

Supply and fixing of CPVC puddle pipe with flange having a length such that there is 30cm and 10cm over hang outside and inside of the tank respectively or as suggested by engineer in charge which ever is greater 100mm inner diameter

Supply and fixing of CPVC puddle pipe with flange having a length such that there is 30cm and 10cm over hang outside and inside of the tank respectively or as suggested by engineer in charge which ever is greater 65mm inner diameter

;Supply and fixing of CPVC puddle pipe with flange having a length such that there is 30cm and 10cm over hang outside and inside of the tank respectively or as suggested by engineer in charge which ever is greater 50mm inner diameter

Supply and fixing of CPVC puddle pipe with flange having a length such that there is 30cm and 10cm over hang outside and inside of the tank respectively or as suggested by engineer in charge which ever is greater 25mm inner diameter

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soilPipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia

Extra for depth for manholes Size 120x90 cmWith common burnt clay F.P.S. ( non modular ) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design: Inside size 120x90 cm and 90 cm deep including C.I. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg):With common burnt clay F.P.S ( non modular) bricks of class designation 7.5

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SCH 40) pipes, having thermal stability for hot&cold water supply including all CPVC plain&brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes&fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work - Exposed on wall 50mm nominal diameter pipe For Pumping main water TO OHT

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC SCH 40) pipes, having thermal stability for hot & cold water supply including all CPVC plain&brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes&fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work/external work - Exposed on wall 40mm nominal diameter pipe For Pumping main water TO OHT

Design, Supply, installation, testing, and commissioning of a complete Water Treatment Plant (WTP) with a minimum capacity of 7 m³/hr, designed for continuous operation of 7 hours per day. The system shall comprise a Pre-Treatment Unit including High Pressure Sand Filter, Activated Carbon Filter, and Multiport valves; Chemical Dosing system; Filter Feed Pump Set (1 working + 1 standby) with necessary control panel; and a main treatment section as required (such as softener, UV/UF/RO system) based on the final water test report. The scope shall include all interconnecting piping, valves, supports, and accessories to deliver treated water meeting the required quality standards. The complete system shall conform to approved technical specifications.

DSR No.

Wiring for circuit / submain wiring along with earth wire with the following sizes of HFFR copper conductor, single core cable in surface / recessed medium class PVC conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Installation, testing and commissioning of ceiling fan including wiring the down rod of standard length (upto 30 cm.) with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Wiring for group controlled (looped) light point / fan point / exhaust fan point / call bell point (without independent switch etc) with 1.5 sqmm FRLS PVC insultated copper conductor single core cable in surface / recessed PVC conduit, and earthing the point with 1.5 sqmm FRLS PVC insultated copper conductor single core cable etc as required.

Supplying, installation, testing & commissioning of Passive Infrared (PIR) technology based occupancy sensor having high performance, non regulating programmable type, suitable for connected load upto 10 amp, for mounting height upto 2.8m and for 5 m diameter coverage area along with necessary fixing arrangement, box for surface mounting, i/c programming at site etc complete as required.

Supplying, installation, testing & commissioning of Astronomical time switch of following configuration to be mounted in feeder pillars / Lighting DBs for automatic switching On & Off of street lights at sun set & sun rise or twilight (Auto ON, Auto Off, Auto modes) with manual override facility with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site complete as required.

Supplying and fixing following way single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, interconnection, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)

12 way double door

Supplying and fixing following way horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess complete with tinned copper busbar, neutral busbar, earth bar, din bar, interconnection, powder painted including earthing etc. as required. (But without MCB/ RCCB/ Isolator)

Supplying and fixing following way surface / recess mounted vertical type, 415 volt, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200amps tinned copper busbar, common neutral link, earth bar, din bar, for mounting MCB's, (but without MCB's and incomer), as required. (Note: Vertical type MCB TPDB is normally used where 3 phase outlets are required).

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing DP sheet steel enclosure on surface / recess along with 25/32 amps 240 volts, "C" curve DP MCB complete with connections, testing and commissioining etc as required.

Supplying and fixing FP sheet steel enclosure on surface / recess along with 16/25/32 amps 415 volts, "C" curve FP MCB complete with connections, testing and commissioining etc as required.

Supply & installing following size of perforated Hot dipped Galvanised Iron cable tray (galvanisation thickness not less than 50 microns) with perforations not more than 17.5%, including bends, tees, cross member, reducer etc in convenient sections, joined with connectors, suspended from the ceiling with GI suspenders including GI bolts & nuts etc as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke as required.

Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode, including connection/ termination with GI thimble etc. as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing open duct as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.

Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

Supplying, installation, testing and commissioning 8 mm Aluminum Round Conductor complete as specified in drawing & Meets the requirements of (IS/IEC 62305)

Supply and providing 2 mm thick & 1 m wide electrical grade insulating mat to withstand 3.3 KV dielectric strength conforming to IS 15652/ 2006.

DSR No.

Supplying, installation, testing & commissioning of loop powered addressable sounder / hooter cum strobe complete with enclosure for mounting on wall surface, cable termination using gland & locknut, connections etc including all power supply and accessories as required. The device shall comply NFPA/ EN54 / UL with latest amendment upto date.

Supply, Installation,Testing & Commissioning of Fire Fighters Telephone system / console which is capable of providing annunciation and control for local and remote telephone handsets of minimum 15 users. It includes a built in display & keypad that provide an indication of phone activation as well as corresponding trouble conditions. The telephone connections can be monitored individually or as a group of multi-phone jacks. The system has to have built-in auto program feature. The console shall be provided with necessary power supply unit, battery back up for 24 hr normal operation and 2 hr during emergency condition including all accessories as required. The device shall comply NFPA/ EN54 / UL with latest amendment upto date.

Supplying, installation, testing & commissioning of Fire fighters telephone jack in suitable enclosure for recess mounting, cable termination, connections etc complete with all accessories as required. The device shall be compactable to the fire fighters telphone system and comply required standards.

Supplying, installation, testing & commissioning of Fire fighters remote handset in suitable enclosure for recess mounting with all necessary accessories complete as required.The device shall be compactable to the fire fighters telphone system and comply required standards

Supply laying and termination of 2 Core x 1.5 Sq.mm cable, Armoured, Screened, FRLS, PVC Insulated copper cable along with all accessories as required. The cable shall be terminated in all devices and control panel by using properly sized cable gland & locknut. Cable shall be installed on wall / slab by using GI saddles at regular intervals as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part Il complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc. , complete as required 63 mm dia(OD-63mm & ID-51mm nominal)

SITC of Repeater panel with all accessories

SITC of 10/ 100/1000 1G Ports+ 4 Combo 10/100/1000 GE/SFP ports + 4 10G SFP+ ports, - Core Switch

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Item Code

Supplying and fixing air vessel made of 250 mm dia 8 mm thick MS sheet , 1200 mm in height with Air release valve on top and flanged connection to riser , drain arrangement with 25 mm dia Gun metal wheel valve with required accessories, pressure guage and painting with synthetic enamel paint of approved shade as required.

Providing and fixing of pressure switch in MS pipeline including connection etc as required:

Providing, installation, testing and commissioning of adjustable rosette plate for 15 mm dia in white finish UL listed or FM approved complete as required:

Item Code

Supply, installation, testing and commissioning (SITC) of 3 TR capacity aircooled inveter type Outdoor condensing unit with single/multi scroll compressor as per specifications complete with suitable capacity drive motor, air cooled condenser with all accessories, hermetically sealed scroll compressor, electronic microprocessor pendant controller with digital display, first charge R 407A/R410A refrigerant gas, vibration isolator pads and saftey devices like thermal protector, pressure relief valve, over load relays single phase preventor, high-low pressure cut out, suitable for three phase 440V supply

Supply, installation, testing and commissioning (SITC) of 8.5 TR capacity aircooled inveter type Outdoor condensing unit with single/multi scroll compressor as per specifications complete with suitable capacity drive motor, air cooled condenser with all accessories, hermetically sealed scroll compressor, electronic microprocessor pendant controller with digital display, first charge R 407A/R410A refrigerant gas, vibration isolator pads and saftey devices like thermal protector, pressure relief valve, over load relays single phase preventor, high-low pressure cut out, suitable for three phase 440V supply

Supply, Installing, Testing and Commissioning of Ductable Fan Coil Units for VRF with corded remote control, each complete with 3 / 4 rows deep Coil, cleanable fabric filters, main condensate extended SS drain pans, as described in specifications, casing, coil piping connections, through copper pipes, condensate drain connections, wiring, control wiring in conduit upto thermostat boxes.

Supply, installation, testing and commissioning of 1.5 TR High Wall Mounted Inverter Split Air Conditioner, 5-Star BEE rated, comprising indoor wall-mounted fan coil unit with cordless remote control and outdoor air-cooled condensing unit with energy-efficient rotary inverter compressor, suitable for single-phase 230 V, 50 Hz power supply, using eco-friendly refrigerant R32 / R410A / R407C. Including fixing of indoor unit on wall and outdoor unit on MS stand or raised platform as per manufacturer’s recommendation, refrigerant grade copper piping up to 3 m (inclusive) with 13 mm thick nitrile rubber insulation, insulated PVC condensate drain piping up to 4 m (inclusive), interconnecting refrigerant and control wiring, electrical cabling from nearest power point, canvas connections, first charge of refrigerant, suitable stabilizer,etc complete as required All routing, coordination and execution shall be carried out as per site conditions and approved drawings, and the contractor shall be deemed to have inspected the site and included all works within the above limits, with no extra claim on account of routing, access or coordination constraints.

Supply, installation, testing and commissioning of 1 TR High Wall Mounted Inverter Split Air Conditioner, 5-Star BEE rated, comprising indoor wall-mounted fan coil unit with cordless remote control and outdoor air-cooled condensing unit with energy-efficient rotary inverter compressor, suitable for single-phase 230 V, 50 Hz power supply, using eco-friendly refrigerant R32 / R410A / R407C. Including fixing of indoor unit on wall and outdoor unit on MS stand or raised platform as per manufacturer’s recommendation, refrigerant grade copper piping up to 3 m (inclusive) with 13 mm thick nitrile rubber insulation, insulated PVC condensate drain piping up to 4 m (inclusive), interconnecting refrigerant and control wiring, electrical cabling from nearest power point, canvas connections, first charge of refrigerant, suitable stabilizer,etc complete as required All routing, coordination and execution shall be carried out as per site conditions and approved drawings, and the contractor shall be deemed to have inspected the site and included all works within the above limits, with no extra claim on account of routing, access or coordination constraints.

Supply & Installation of Copper Refrigerant piping suitable for High Wall mounted Split units, duly insulated with closed cell elastomeric nitrile rubber insulation, class-0, covered with two layers of shield coating, complete with elbows, T joints, sleeves etc. with GSS slotted rail supporting arrangement from ceiling/wall and GI clamp for individual pipes.

Supply, Installation, Testing and Commissioning of GI Volume Control Damper complete with neoprene rubber gaskets, nuts, bolts, screw linkages, flanges etc. as per specifications.

150 mm Dia

200 mm Dia

250 mm Dia

Supplying, Fixing, testing and commissioning of fire dampers in supply air duct/ main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Actuator

Item Code

DSR CODE

DSR ANALYSIS

Providing and fixing of durable prohibition and information signage. Made of cast acrylic (4mm and 3mm thick) duly laser cut and text and pictogram PVC vinyl over which specified color will be pasted , all fixing and hanging arrangements in 304 grade SS mirror fasteners and hanging provision ss rope, chain etc as per design at the required location as per the direction of engineer in charge. Including cost of all creative designing and planning, site maping charge ,conveyance, materials, labour charge, scaffolding etc.Size:120x80mm (3mm thick Acrylic base)

Providing and fixing of durable prohibition and information signage . Made of cast acrylic (4mm and 3mm thick) duly laser cut and text and pictogram PVC vinyl over which specified color will be pasted , all fixing and hanging arrangements in 304 grade SS mirror fasteners and hanging provision ss rope, chain etc as per design at the required location as per the direction of engineer in charge. Including cost of all creative designing and planning, site maping charge,conveyance, materials, labour charge, scaffolding etc.Wall Hanging signage 800x200mm (4mm thick Acrylic base)

Providing and fixing of durable prohibition and information signage at New block.Made of cast acrylic (4mm and 3mm thick) duly laser cut and text and pictogram PVC vinyl over which specified color will be pasted , all fixing and hanging arrangements in 304 grade SS mirror fasteners and hanging provision ss rope, chain etc as per design at the required location as per the direction of engineer in charge. Including cost of all creative designing and planning,site maping charge ,conveyance, materials, labour charge, scaffolding etc.Wall Projected Signage 500x120mm (3mm thick acrylic base)

Providing and fixing of durable prohibition and information signage at New block. Made of cast acrylic (4mm and 3mm thick) duly laser cut and text and pictogram PVC vinyl over which specified color will be pasted, all fixing and hanging arrangements in 304 grade SS mirror fasteners and hanging provision ss rope, chain etc as per design at the required location as per the direction of engineer in charge. Including cost of all creative designing and planning, site maping charge ,conveyance, materials, labour charge, scaffolding etc.. Group Arrow Signage 800x600mm (4mm thick acrylic base)

Providing and fixing of durable prohibition and information signage . Made of cast acrylic (4mm and 3mm thick) duly laser cut and text and pictogram PVC vinyl over which specified color will be pasted , all fixing and hanging arrangements in 304 grade SS mirror fasteners and hanging provision ss rope, chain etc as per design at the required location as per the direction of engineer in charge. Including cost of all creative designing and planning, site maping charge ,conveyance, materials, labour charge, scaffolding etc.. Main Directory board 1220 x 2444 mm (4mm thick acrylic base)

PRINTED VINYL: Providing and pasting of custom designed HP latex high quality vinyl prints for OP,Regi.pharma.counters,consulting and treatment rooms inside the hospital etc, as per design at the required locations as per the direction of engineer in charge. Including cost of all materials, labor charge,scaffolding etc

DSR ANALYSIS

PROVIDING AND FIXING OF ILLUMINATED LED SIGNAGE (wall fixing)made of 2mm thick cast acrylic dualy laser cut and minimum letter thickness from the surface is 2 inch. Power supply SMPS need minimum one year replacement warranty). cost of all creative designing, materials, labour charge, scaffolding etc.. complete. SIZE:400X60CM

Item Description

Gas Outlet Points/ Terminal Units with probe: Supply,Installation, testing and commissioning of Gas outlet points for Oxygen, Medical Air 4 Bar , Vacuum,

Medical Air 4 outlet with probe

AREA VALVE BOX (WITH VALVES) : Supply,Installation, testing and commissioning of Area Valve Boxes

MEDICAL GAS ALARM PANEL : Supply, Installation, testing and commissioning of Medical Gas Alarm Panel.

LINE ISOLATION VALVES

OT Pendants (Anesthetist & Surgeon)

Item Code

Project Component

Operation & Maintenance of entire system for a minimum period of 9 Years including consumables and manpower after completion of 12 months of operation.

1st year

2nd year

3rd Year

4th Year

5th Year

6th Year

7th Year

8th Year

9th Year

Project Component

CAMC for 7 years after completion of DLP

1st year

2nd year

3rd Year

4th Year

5th Year

6th Year

7th Year

Providing Comprehensive Maintainenace Contract for Medical Gas Pipeline System (MGPS) on successful completion of Warranty

1st year

2nd year

3rd Year

4th year

5th year