CA NO GE(N)AMB-78/2024-25 SPECIAL REPAIR TO BLDG NO HT-27 OF ESP AND PROVN OF Y SHAPED ANGLE IRON WITH CONCERTINA COIL ON EXISTING SECURITY WALL UNDER AGE B/R-I GE (NORTH) AMBALA CANTT

Amount

Schedule 'A' Part-I (B/R itmes) Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc complete, all as specified and as directed.

Material and labour for rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar 1:4 not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine stone aggregate of size between 6 to 12 mm as per the texture required mixed with coarse sand and cement in the ratio 1:1:1 shall be applied, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of Old plastered/unplastered surfaces of walls, chajjas, roof projection, etc. and applying one coat of cement base paint complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new plastered/unplastered surfaces of walls, chajjas, roof projection, etc. and applying two coats of cement base paint over a coat of primer complete, all as specified and as directed by the Engineer-in-Charge.

Dismantling of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles , complete, all as specified and as directed.

Material and labour brick work with sub class 'B' old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 , complete, all as specified and as directed.

All as per serial item No. 06 here in befor but except bricks old serviceable bricks obtained from serial item No 05 above including removing motar, cleaning the bricks with water, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 12 mm thick rendering or plastering using polymer modified ready mix plaster of fine grade Portland cement, graded sand and polymer with water soluble additives as per manufacture's specifications of approved make, on any faces of brick work or concrete wall surfaces and finished even and smooth without using extra cement, complete, all as specified and as directed by the Engineer–in charge. Make:- Smart care ready mix plaster of Asian paint or equivalent in Berger/Ultra tech/Pidilite

Material and labour complete removal of existing treatment on walls, pillars, cornices etc (any number of layers) and rougheing surfaces by scrapping with steel scrappers or any other means, wasing down with water to remove loose particles etc to receive plaster etc, complete all as specified and as directed by the Engineer–in–Charge.

Material and labour for 15 mm thick rendering or plastering using polymer modified ready mix plaster of fine grade Portland cement, graded sand and polymer with water soluble additives as per manufacture's specifications of approved make, on any faces of brick work or concrete wall surfaces and finished even and smooth without using extra cement, complete, all as specified and as directed by the Engineer–in charge. Make:- Smart care ready mix plaster of Asian paint or equivalent in Berger/Ultra tech/Pidilite

Material and labour for preparation of newly plastered/ unplastered surfaces of walls and applying two coats of oil bound distemper with painting roller over and including 02 mm thick wall care putty white cement based in two or more coats to achieve smooth surfaces, complete all as specified and as directed by the Engineer-in-Charge. Notes:- 1. This item shall be executed in two stage (a) First stage : preparation of surfaces & applying wall care putty & make surface smooth (b) Second stage : applied two coats of oil bound distemper. 2. Before execution of 2nd stage the first stage shall be passed by Engineer-in-charge & proper record there of shall be maintained.

Material and labour for preparation of old plastered/ unplastered surfaces of walls and applying two coats of oil bound distemper with painting roller over and including 02 mm thick wall care putty white cement based in two or more coats to achieve smooth surfaces, complete all as specified and as directed by the Engineer-in-Charge. Notes:- 1. This item shall be executed in two stage (a) First stage : preparation of surfaces & applying wall care putty & make surface smooth (b) Second stage : applied two coats of oil bound distemper. 2. Before execution of 2nd stage the first stage shall be passed by Engineer-in-charge & proper record there of shall be maintained.

Material and labour for preparation of old plastered surface of walls and applying two coats of cement based paint, complete, all as specified and directed by engr-in-charge.

Material and labour for preparation of new plastered surface of walls etc and applying two coats of cement based paint complete, all as specified and directed by engr-in-charge.

Material and labour preparation of old decorated or painted steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint complete all as specified and as directed by the Engineer-in-Charge.

Dismantling stone tiles (old broken Kota stone) of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar.

Material and labour PCC 1:4:8, type D–2 (using 40mm graded crushed stone aggregates)as foundation filling & mass concrete etc, complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for 25 mm thick PCC 1:2:4, type B–0 as in sub base floor (using 12.50mm graded crushed stone aggregate), finished even & fair without using extra cement complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for machine cut kota stone slab flooring 18 to 22 mm thick (each slab size not less than 550mm x 550mm) in floor, set and jointed in neat cement slurry with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises, complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for glazed ceramic coloured tiles premium/1st quality in vertical surfaces/skirtings/dados of size 300x600 x7-8mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match over and including 10mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:4 complete all as specified and as directed by the Engineer-in-Charge.

Taking down chowkats or frames with shutter area exceeding 1.50 Square meter and not exceeding 4.00 Square meter (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish,complete, all as specified and as directed by the Engineer-in-Charge.

Taking down shutters of any description area exc 1 sqm and not exc 2 sqm and removing from site , complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour rolled mild steel framed work as in chowkats of door or gates of angle or other section with gusset plates, rails braces etc. complete. drilled for fixing for steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and hanging ,door fitting (exclusive of steel sheeting or other covering, running rails and guides) also fastening and fixing conforming to Fe–290–W (Grade E–165) quality 'A' , complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing factory made 2nd class hard wood 35 mm thick plain framed panelled shutter( two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both face . The size of rail and style as per IS:1003 (Part-1) kiln seasoned and chemically pressure treated , complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing factory made 35 mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc. (without sash bars) ,edges of framing plain chamfered or rounded , fitted with cut and mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section-8, clause 8.24 (a) (wood shall be kiln seasoned and chemically pressure treated) , complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing galvanised mild steel wire cloths 0.56 mm nominal dia of wire and average width of aperature 1.18mm and fixed with tinned tacks or galvanised mild steel wire staple , complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed , complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 125 mm long aluminium handle fabricated type anodised , complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing 300mm long aluminum alloy, anodized sliding bolts with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminum alloys to door shutter , complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing mild steel 150 mm, ordinary rat tail rod pattern springs, including roller and roller plate complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete, all as specified and as directed by the Engineer-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds and steel window frame glazed with putty or fixed with beads , complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing for aluminium alloy anodized (power-coated) partition, with aluminium sections as per of " Jindal' section including aluminium alloy anodized alloy anodized snap type beads, handles, glazing clip, joint cleats, rubber gaskets etc , complete all as specified and directed. For series-B "Jindal" section numbers for casement. NOTE- (i) the rates shall be inclusive of provision of and fixing of rubber packing/gasket. (ii) Glass /wire gauge /Board shall be measured and paid for separately.

Material and labour 12mm thick prelaminated particle board interier grade (grade–1) confirming IS 14587 prelaminated both side with decorative choice lamination and fixed to aluminium frame work with glazing clips, rubber etc, complete, all as specified and as directed by the Engineer-in-Charge.

Demolition of Reinforced Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) Roofs, floors (other than ground floors), beams, staircases, landing, chajjas, lintels and similar suspended work, complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour plain cement concrete 1:2:4 type B–0 (using 12.50mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including formwork for rough finished surfaces of concrete, complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for TMT steel bars 10mm dia and over cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia, complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for TMT steel bars 5mm dia and over up to and including 10mm dia in stirrups, spacers etc, cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia, complete, all as specified and as directed by the Engineer-in-Charge.

Dismantling asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings , complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick having zinc coating 150 grams per Sqm (Az 150) of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws , complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa having zinc coating 150grams/Sqm (Az-150) as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed by the Engineer-in-Charge.

Demolition of cement concrete (un–reinforced) in ground floors and pavings not exe 15 cm thickness (below or above ground level) complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour providing 75 mm thick cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregates as in plinth protection laid in alternate bays (not exc 2 Sqm each ) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight including form work complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for vibratory rubber moulded coloured precast concrete interlocking paver block, any shape and size conforming to IS 15658-2006, ISI marked of 60 mm thickness, grade M-35 with grey cement and pigments over and including a layer of sand cushioning, 25 mm thick, Including dismantling of existing unserviceable inter locking tiles/paver block etc with sand cushioning complete all as specified and as directed by the Engineer-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness including cover fillets and false ceiling frame work , complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing false ceiling with semi perforated 12 mm thick micro tegular edged at all hights with GRG (glass fiber reinforced gypsum ) false ceiling tiles of size 595mm x 595mm of approved texture ,design and pattern having moisture content less than 2% ,humidity resistance of 99% ,NRC 0.5 to 0.75 as per IS 8225-1987 ,non- combustile as per BS475 (part-4) -1970 and light code description unit rate No.429 SUB HEAD :26.0 new technologies and material reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm th (galvanised @ 120 gms per sqm including both sides ) comprising of main -T runners of size 15x32mm of length 3000mm ,cross T of size 15 x 32mm of length 1200mm and secondry intermediate cross-T of size 15x32mm of length 600 mm to form grid module of size 600x600mm ,suspended from ceiling using galvanised mild steel items (galvanising @80 gms per sqm ) i.e, 50mm long ,8 mm outer diameter M-6 dash fastners ,6mm dia fully threaded hanger rod upto 1000mm length and L- Shape level adjuster of size 85x25x2mm . Galvanised iron perimeter wall angle of size 24x24x0.4mm of length 3000mm to be fixed on periphery wall /partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws . complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing as in repair stainless steel curtain rod 25mm dia having wall thickness 1.60mm with and including stainless steel decorative brackets, two lotto or finials for each end etc fixed with stainless steel screws , complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for 18 to 20mm thick white marble work (table rubbed and polished) using 50mm wide strips in floors and like over and including 15mm thick screed or bedding layer in cement mortar (1:4) and pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade.complete, all as specified and as directed by the Engineer-in-Charge.

Providing edge moulding to 18-20mm thick stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour 18 to 20 mm thick machine cut kota stone slab as in skirting, riser of steps, dado & pillar etc. over and including 10mm thick screed layer in cement mortar 1:4 set and jointed in neat cement slurry mixed with pigment to match the shade including grinding and polishing, complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe -290 Gde-E-165 complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour 100 mm thick PCC 1:4:8 Type D–2 using 40mm graded crushed stone aggregate as in sub base of floor/ hard standing etc and finished even and fair without using extra cement complete, all as specified and as directed by the Engineer-in-Charge.

Supply and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage complete all as specified and as directed by the Engineer-in-Charge.

Cutting holes in brick walls exc half brick wall but not exc one brick wall built in cement mortar or cement lime mortar and stone walls built in lime mortar upto 30 cm depth for inserting holdfasts or embedding fencing posts and making good dismantled portion in cement mortar (1:3) or cement concrete 1:2:4 Type B-1 as required ® complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for cement concrete Type B–1, 1:2:4 (using 20 mm graded crushed stone aggregate) as in PCC padding, paving, coping, roof kerbs or mud stops, rounded, door cill, hold fast and other like works complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for mild steel work in hand rails, half round or other stock section or core for wooden handrail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc, and similar work conforming to Fe 290-W (Gde E-165), complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165 complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for preparation of new steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing, galvanized, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured), complete, all as specified and as directed by the Engineer-in-Charge.

Supply and fixing Concertina coil 600mm dia (in strectch Position) hot dip galvanised steel wire coated with CLR anti corrosive paint. Making diamond shape with the help of dove tail clips (18 SWG) fixed over barbed wire with angle iron, the concertina coil is to be fixed with barbed wire at point wherever coils touch the bottom of barbed wire with the help of hog rings (14 SWG) complete all as specified (barbed wire and angle iron shall be measured and paid separately ) Note :- Hoggong shall be fixed at a interval of 600 mm C/C wherever it touched with barbed wire and overlapping of concertina coil and barbed wire shall be 300mm. it shall be deemed to be included in the unit rate

Dismantling of MS work of any description in any section, in fencing, post and struts etc embedded in conctrete, brick work, masonry etc including taking out embedded portion and making good complete all as specified and as directed by the Engr-in-charge.

Taking down or dismentling existing barbed wire at any position, complete, all as specified and as directed by the Engineer-in-Charge.

Schedule 'A' Part-II (E/M items) Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, pendant, lamp holder, socket outlet, etc and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc complete all as specified and as directed by the Engineer-in-Charge.

Taking down ceiling fan any size or any type and deposited to concerned AGE E/M store yard complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor drawn through and including medium grade, ISI marked, PVC conduit not less than 20 mm dia with accessories, concealed on wall/ceiling surfaces and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable FRLS-H, 1100 volt grade, ISI marked with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes modular type of size/modules as required at site with earth dolly (boxes shall be galvanised or painted with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally) including provision of new covered plate over sunken box for housing the modular switches , modular socket outlets,modular fan regulators etc. for one light/fan/exhaust fan/bell point controlled by one way switch, complete all as specified and as directed by Engineer-in-Charge. Note :- a) .All chases will be cut by chase cutter only b) Switch, socket outlet and fan regulators to be measured and paid for separately .

Description all as per serial item No.67 here-in-before but for One 3 pin, 6 Amps, socket outlet controlled by one switch on independent board, complete all as specified and as directed by Engineer-in-Charge.

Description all as per serial item No.67 here-in-before but for One 3 pin 6 Amps socket outlet controlled by one switch on same board, complete all as specified and as directed by Engineer-in-Charge.

Description all as per serial item No.67 here-in-before but for one socket outlet 16 Amp with 2.50 sq mm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked with multi stranded copper conductor along with 2.50 sqmm PVC insulated , unsheathed cable green colour FRLS-H, 1100 volt grade, ISI marked with multi stranded copper wire as earth continuity conductor connected to common earth dolly complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing of modular switch 1 module, single pole, one way 6 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular switch 1 module, single pole, one way 16 Amps flush type, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular socket outlet 2/3 pin combined, 6 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of modular socket outlet 3/3 pin combined, (6pin), 6/16 Amp, one way, two module, 230 volts complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing as in repair electronic Fan regulator modular 100 watt, 1 module, 230 volts , 50 Hz, AC supply suitable for ceiling fan any type/make/sweep complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing ceiling rose surface type 2/3 terminal polycarbonate, isolated body complete all as specified and as directed by the Engineer-in-Charge.

Supply and fixing in repair LED batten fitting 18-20 watt, 4 feet, aluminium housing with electronic driver cool/warm type industrial model complete, connecting with copper conductor flexible cable from ceiling rose to connector of the light complete all as specified and as directed by the Engineer-in-Charge. Cat part No. LUMILINEPLUSNEOBS20WLED830SPCSSIND of make Havells or equivalent in make given in Appx 'B'.

Supply and fixing in repair, LED Bldg Security Light Fittings of capacity 20 -25 watt made up of die cast aluminium housing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with IP-65 protection and other connected accessories including electronic driver and making electrical connection,service bracket of mild steel pipe 25 mm bore medium grade of length 0.70 mtr fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts and washer and suitable reducer for connecting fitting to GI pipe as required at site including two coats of synthetic enamel paint over one coat of red oxide primer on mild steel work complete all as specified and as directed by the Engineer-in-Charge. Cat part No.ENDURASUNDOWNSL25WLED765PASYBOTGIHD of make Havells or equivalent in make given in Appx 'B'.

Supply and fix sheet metal MCB DB SPN 4 way with 200 Amps rated bus bar single pole and neutral with double door IP-54 fixed on wall duly grouted in solid block wall or on wooden board in and including copper lugs/thimbles duly crimped for connection, including making smooth the disturbed surfaces including removing old unserviceable enclosure complete all as specified and as directed by the Engr-in-charge. Cat part No.811824 of make Indo Asian or equivalent in make given in Appx 'B'.

Supply and fix MCB SP, 6-32 Amps, 240 volt, 10 KA, 'B' curve as per site requirement including removing old unserviceable MCB complete all as specified and as directed by the Engineer-in-Charge.

Supply and fix MCB SPN 32 Amps, 240 volt, 10 KA, 'B' curve as per site requirement including removing old unserviceable MCB, complete, all as specified and as directed by the Engineer-in-Charge.

Taking down and refixing only ceiling fan after cleaning in any model/size etc and making all connection using three core copper conductor flexible cable in size 1.5 sqmm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector, complete, all as specified and as directed by the Engineer-in-Charge.

Supply & laying as in repair sub main wiring with two run of 6 sqmm PVC insulated, unsheathed cable FRLS-H,1100 volts grade ISI marked with multi stranded copper conductor and one run of 6 sqmm PVC insulated, unsheathed cable FRLS-H, 1100 volt grade ISI marked multi stranded copper conductor as earth continuty conductor connected to common earth dolly including concealed on wall/ceiling surfaces in and including PVC conduit medium grade ISI marked of adequate size for housing the wires complete all as specified and as directed by the Engineer-in-Charge. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Three runs of cable and one run of PVC conduit shall be measured and paid as one unit length.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earth strip 25 x 3mm thick by means of bolts, nuts, check nuts and washers of galvanised iron.Earth strip protected by GI pipe 32mm bore(medium grade) and connected to earthing test point as directed and as specified and shown in electrical plate No. 3 of SSR Part I (2009) including necessary concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia TMT bars @ 15cm c/c both ways with one handle for lifting made out of 8mm dia bar, funnel, wire mesh, 20mm dia GI pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testing as in repair complete all as directed by Engineer-in-Charge and earth testing on completion .

Note:- Amount of credit of Rs. 1,72,841.70 for retrieved materials is mentioned in Schedule of Credit Page No. 125. of tender doCubic metre ents in pdf form which will be deducted offline while acceptance of tender.

Swami Enterprises (BID ID -3272614)

shiv const co (BID ID -3274802)

bhagwandasswazirchand (BID ID -3277401)

Parveen Kumar (BID ID -3275095)

Sham Sunder Bansal (BID ID -3278470)