Special repairs to bldg No T 22 T 24 Kote T 23 Qtr guard and T 120 under GE North Ambala Cantt

Amount

SCHEDULE A PART I (B/R WORKS)

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness (below or above ground level) and removal the rubbish/ demolished material outside defence land, complete, all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness, laid bedded and pointed in any mortar in floors, aprons, etc. removing the rubbish outside the defence land ,complete all as specified.

Material and Labour for taking down cement or cement lime plaster of any description on brick or stone walls or over concrete surface etc including raking out joints hacking for key scrubbing down with water etc including removal of vegetation/roots in any description, complete all as specified and as directed.

Dismantling of brick work or stone masonry, precast cement concrete walling built in cement mortar including all quoins, arches, pillars etc., complete all as specified and as directed.

Material and Labour for 15mm thick rendering on brick work, concrete surfaces of any description in cement mortar 1:4 mixed with WPC @2% by weight of cement or as per manufacturer’s instructions, finished even and fair complete all as specified and directed. Note : Supply only WPC shall be measured and paid for separately

Material and Labour for rendering 15 mm thick on brick or concrete surfaces in cement mortar 1:6 including finishing surfaces even and smooth without using extra cement complete all as specified and as directed.

Supply only Integral waterproofing compound complete all as specified and approved by GE.

Material and labour for brick work with subclass ‘B` old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed.

Material and Labour for Brick work with sub class ‘B’ bricks (Except Bricks), straight or curved on plan exceeding 6 metre mean radius, built in cement mortar (1:6) complete, all as specified and directed. ( Note- The serviceable bricks obtained from Serial item No-1.04 will be used after removing motar, cleaning the bricks with water, etc.)

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work including cutting of steel reinforcement as required to facilitate demolition and removal the rubbish/ demolished material outside defence land, complete all as specified and directed.

Material and labour for machine cut kota stone slab 18-22 mm thick (of size not less than (55 cm x 55 cm) laid in flooring and jointed and pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting waste, rubbing and polishing (Granite finish) over and including cement screed bed 20mm thick in cement mortar (1:4) base complete, all as specified and as directed .

Material and labour for machine cut kota stone slab 16-18 mm thick laid on vertical surface and jointed & pointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) but as in skirting over and including 10mm thick plaster in cement mortar (1:3) on brick work or concrete surfaces complete, all as specified and as directed.

Material and labour for 50mm thick, PCC 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregate) as in plinth protection/PCC path, and paving, finished the surface even and smooth without using extra cement, joint filled with bitumen and sand mixture applied hot (area not exceeding 1.20 sqm ) , complete all as specified and as directed.

Material and labour for premium quality, joint free, non skid coloured ceramic tiles (Square/rectangular) , area of each tiles exceeding 0.11 sqm and not exceeding 0.18 sqm and 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the surface over and including cement screed bed 15mm thick in cement mortar (1:4) , complete all as specified and as directed .

Material and labour for premium quality, glazed coloured ceramic tiles of size 450mmX300mmX7mm to 8mm on vertical surfaces of walls laid over and including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match, complete all as specified and as directed.

Material and labour for premium quality, joint free, anti skid coloured porcelain tiles, 7 to 8mm thick, square/rectangular, area of each tile exceeding 0.18sqm but not exceeding 0.36sqm as in floor, over and including cement screed bed 15mm thick in cement mortar (1:4), set and jointed in neat cement slurry @ 3.00 kg/square metre and pointed in white or coloured cement to match the tile surface complete all as specified and as directed.

Material and labour for premium quality, joint free, anti skid coloured porcelain tiles, 7 to 8mm thick, , of same description and length as of floor tile but 150 mm height on vertical surfaces of walls including 10mm thick rough finished plaster in cement mortar (1:3) set jointed in neat cement slurry and pointed in coloured cement to match ,complete all as specified and as directed .

Taking down chowkats or frames area not exceeding 1.50 Square metre (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed.

Taking down chowkats or frames area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (without taking off shutters from the frames) and removing from site, including cutting holes for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces to match with existing finish complete all as specified and as directed.

Taking down mild steel door/gate with frames area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (w/o taking off shutters from frames) and and refixing in the same/ other opening including repair to door shutter, locking system, grill/MS sheet, pintel,hold fast, etc., complete all as specified and as directed.

Taking down mild steel door/gate with frames area exceeding 450 Square metre and not exceeding 7.50 Square metre (w/o taking off shutters from frames) and and refixing in the same/ other opening including repair to door shutter, locking system, grill/MS sheet, pintel,hold fast, etc., complete all as specified and as directed.

Material and labour for framed work as in chowkhats, doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering door etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, tie bar to be welded to steel door chowkhat (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete Fe-290 (Gde E-165) complete all as specified and as directed.

Supply and fixing factory made shutter, 35 mm thick, 2nd class hardwood (Hollock) rail and style, plain framed, paneled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

Supplying & fixing for solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S.square tube and fixing in opening, complete all as specified and as directed.

Supplying & fixing for Factory made solid panel PVC moulded door shutter with particle board core, 28 to 30 mm thick (style) with 2, 4, or 6 raised panel design with 2mm thick prelaminated PVC Sheet on the front face and 2mm plain colour PVC sheet on back face and fixed in the frame complete, all as specified and as directed.

Supply and fixing steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on CECZ Chandigarh drawing No TD-219(c) sheet 1/3 to 3/3 and TD-220(c) sheet 1/3 to 3/3 as applicable, complete all as specified and as directed. Note: (i) For the purpose of measurement and payment double shutter with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill 10 mm square bar irrespective of whatever shown on drawing. (iii) Glazing, wire mesh and painting shall be measured and paid for separately.

Supply and fixing IInd class (hollock) factory made 35mm thick glazed skeleton shutters, open rebated and prepared to receive glass, gauge etc., divided into squares, edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass/gauge etc. with sizes of members of shutters as specified in para 8.24(a) of SSR 2009 (Part I) complete all as specified and as directed.

Supply and fixing aluminum handle, cast type, anodized 150mm long, ISI Marked complete all as specified and as directed.

Material and labour for sheet glass, 3mm thick, ordinary quality and glazing with oil putty, in square not exceeding 0.5 sqm in each pane complete all as specified and as directed.

Supply and fixing 300 mm aluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete, all as specified and directed..

Supply and fixing mild steel helical door spring, 150 mm long, fixed to wooden chowkats or welded to angle iron/ steel door frames complete all as specified and as directed.

Supply and fixing for butt hinge, ISI Marked, 100mm size, medium weight, cold rolled mild steel, complete, all as specified and as directed.

Material and Labour for mild steel TMT bars of 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete, all as specified and as directed .

Material and Labour for mild steel TMT bars of 6mm to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete, all as specified and as directed.

Use and waste of formwork to sides and soffits of roof beams, cantilever, bressummers ,lintels , shelves including supports and similar work for rough finished flat surfaces of concrete, complete all as specified.

Supplying and Fixing for brass tubular towel rail (finish Glossy), 20mm dia, D type, 60cm long between flanges, complete, all as specified and as directed. Make: Prima Art No- PSD-4502A or equivalent model in makes mentioned in Appendix 'B' of tender document. Note- Contractor shall submit a guarantee certificate for tubular towel rail from manufacturer to Engineer-in-Charge before claiming payment.

Material and labour for taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Supply and fixing for ISI Marked, 15mm bore, medium grade GI tubing with all fittings complete all as specified and as directed.

Material and labour for taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed.

Material and labour for 20mm bore, `medium grade`, galvanised tubes with all fittings, laid in trenches complete all as specified and as directed.

Supply and fixed (in repair), stop valves, 15 mm dia pipe, chromium plated, fancy type, ISI marked, screwed down, high pressure with capstan head, (concealed type) with long shank, screwed both ends for iron pipes or for unions, complete, all as specified and as directed. Make-Prima Art No- PSP-507 or equivalent models in makes mentioned in Appendix 'B' of tender document. Note: (i) Weight of stop valve shall not be less than 0.575 Kg. (ii) Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment.

Supplying and fixing (in repair), shower arm 240 mm long, light weight , round shape for wall mounted showers with wall flange suitable for 15mm bore pipe including overhead shower rose 125mm dia round shape single flow, complete all as specified and as directed by the Engineer-in-Charge. (Make : Cat No. BS-76 of Prayag or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supply and fixing PVC connections 45cm long and 15mm dia with PTMT nuts and PVC washers on both ends complete all as specified and as directed.

Supply and fixing (in repair), 15mm bore pillar tap, chromium plated cast copper alloy, ISI marked, with capstan head, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks, complete, all as specified and as directed. (Note : Weight of pillar tap shall not be less than 0.665 Kg) Make-ESSCO Cat No ES-507-A or equivalent model in makes mentioned in Appendix 'B' of tender document .

Supplying and fixing (in repair), angle cock, 15 mm dia , brass, chromium plated, ISI marked, screwed down, high pressure with capstain head screwed both ends for iron pipes or for unions, complete all as specified and as directed. (Make : PRIMA cat Part No PSP-504 or Cat No-SQT-526KN of ESSCO or Cat No. PIS-10 of Prayag or equivalent model in makes mentioned in Appendix 'B' of tender document ) Note- Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supplying and fixing ( in repair) stop cock 15mm dia, cast copper alloy, ISI marked, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified and as directed by the Engineer-in-Charge. Note : (Make : JAINKO Model No-SVE-1 or equivalent model in makes mentioned in Appendix 'B' of tender document ) (ii)Contractor will submit to Engineer-in-Charge a guarantee certificate from manufacturer before claiming payment.

Supply and fixing in replacement, mild steel almirah shutters with frame, exceeding 1.5 Square metre, made of 1.00mm thick, mild steel sheet, in two leaves as built in furniture in cupboards including locking arrangement with mortice lock of mild steel, vertical type, 65mm size, 2 lever, ISI marked with duplicate keys and handle, etc. (all as per Godrej pattern) including two coats of spray painting over a coat of red oxide primer complete fixed in brick or concrete wall with minimum six numbers of 10mm dia and 100mm long mild steel bolt with washer and nut in cement mortar (1:4) or PCC 1:2:4, type B-0 complete all as specified and directed.

Supply and fixing 10 litre capacity, virgin polypropylene cistern, ISI marked, coloured, low level including brackets complete with PVC bend/flush pipe and making all connections including taking down existing high or low level unserviceable flushing cistern and making good the disturbed surface to match with the existing surface complete all as specified and as directed.

Supply and fixing in repair, vitreous china wash hand basin, white, wall hung, pedestal pattern, of size 550x410mmx190mm excluding CI brackets but including PVC waste pipe, PVC connections and chromium plated waste coupling, etc.,complete all as specified and as directed. Make : ESSCO Cat part No-ECS WHT 301 or equivalent model in makes mentioned in Appendix 'B' of tender document.

Supply and fixing in repair, water storage tank, 1000 ltr capacity, HDPE triple layer, white coloured, conforming to IS, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore, including taking down the unserviceable water tank and removing from site complete all as specified and as directed.

Supplying & Fixing ( in repair), mild steel 25mm dia, 1.6mm thick, PVC coated, fancy type, heavy duty drapery rod incl pair of MS bracket,finials (latto) at ends including fixing on wall with screws, complete, all as specified and as directed.

Supplying and Fixing for bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles articles conforming to Fe-290.Gde-E-165 complete all as specified and as directed.

Material and Labour for plain cement concrete 1:2:4 type B-1 (using 20 mm graded mechanically crushed stone aggregate) as in fixing of hold fasts, copings, bed plates, kerbs or mud stops, lintels upto 1.50m span, plinth courses, seismic and other bands and the like, finishing the surfaces fair and even including necessary form work complete all as specified and directed. Note- If reinforced concrete, reinforcement shall be measured and paid for separately.

Supplying & Fixing for galvanized mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanized wire staples, complete, all as specified and as directed by the Engineer-in-Charge.

Material and labour for prepration of newly plastered surface of walls and applying two coats of exterior emulsion paint over a coat of primer complete, all as specified and directed

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper with hand roller over 2-3mm thick wall care putty complete all as specified and as directed.

Material and labour for complete removal of existing treatment on surfaces of wall by using appropriate technique as approved by Engr-in-charge for complete removal of all layers of old treatment and reaching upto old plastered surface and applying two coats of exterior emulsion paint over a coat of primer complete, all as specified and directed

Material and labour for complete removal of existing treatment on surfaces of wall by using appropriate technique as approved by Engr-in-charge for complete removal of all layers of old treatment and reaching upto old plastered surface and applying two coats of oil bound distemper with hand roller, over a coat of primer over 2-3mm thick wall care putty , complete all as specified and as directed.

Material and labour for preparing new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

Material and labour for preparation of new steel surfaces/ preprimed surface of steel of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chromate primer complete all as specified and as directed.

Material and labour for preparation of old painted steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed..

Supply and fixing aluminum anodized, barrel tower bolt of extruded section 150mm long, ISI marked complete all as specified and as directed.

Supply and fixing in repair, bib tap, screwed down, high pressure, cast copper alloy, fancy type, chromium plated, ISI marked, with capstan heads, screwed down suitable for 15mm bore pipe or union complete all as specified and as directed. Make : ESSCO Cat No-DLX-511 or Prayag Cat No. 8608 or equivalent model in makes mentioned in Appendix 'B' of tender document. Note- Contractor shall submit a guarantee certificate from manufacturer to Engineer-in-Charge before claiming payment.

Supply and fixing in repair, 100mm dia of outlet, PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed. Note- UPVC fittings shall be conforming to BS 4515 DIN 19531 and DIN 19534

Cutting into existing manholes for connecting new drains, and making good to pipe and rendering cutting out existing benching for and forming branch channel( 1/2 round or 3/4 section ) in cement concrete 1:2:4 type B-1 (using 20mm size crushed stone aggregate) smooth finished and reforming benching as required of pipe 110 mm dia, complete all as specified and directed.

Supply and fixing 110mm dia, UPVC, soil waste drain pipe, type ‘B’, conforming to IS 13592-1992, single socketed, in any length, with rubber rings joints or jointed with solvent cement joint, laid in trenches or in floors complete all as specified and directed. Note- Rubber rings for pipes and fittings shall confirm to IS 5382-1985.

Supply and fixing 110mm dia, UPVC, soil waste drain pipe, type ‘B’, conforming to IS 13592-1992, single socketed, in any length, with rubber rings joints or jointed with solvent cement joint, fixed to wall complete all as specified and directed. Note- Rubber rings for pipes and fittings shall conform to IS 5382-1985.

Supply and fixing in repair, 110 mm bore, UPVC (SWR), plain bend, any radius, including jointing with solvent cement complete all as specified and directed. Note- UPVC bends shall be confirm to BS 4515 DIN 19531 and DIN 19534.

Supply and fixing , 18/19mm thick MDF board, pre laminated exterior grade, confirming to IS 14587 fixed with screw to timber frame work with 5mm thick teak wood edging on one side, bottom and top and other side 10mm teak wood edging with rebate suitable for cup board shutters, palmet box, etc. and leaping treated with french polish complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs any thickness, including cover fillets complete all as specified.

Dismantling asbestos cement corrugated or semi-corrugated sheets including AC ridges etc., as in roof covering, complete all as specified and as directed .

Dismantling of structural steel work of any description, in any position complete all as specified and as directed.

Supply and fixing mild steel work in roof trusses (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (web, tee, angle, channel or flat sections) including distance pieces, cleats etc fixed in position, conforming to Fe-410(Gde 250), complete all as specified and as directed.

Material and labour for 18-20mm thick granite (of any type) ,machine cut and machine polished, and moulded as in steps, jambs, pillar, counter WHB, floor, etc over and including 10mm thick in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and jointed with grey cement slurry , complete all as specified.

Supplying & Fixing for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick, conforming to IS-15961 of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed.. Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965.

Supplying & Fixing for Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete, all as specified and as directed . Note- The sheets shall have (150 gm/sqm total on both sides) with super durable polyester quality paint of approved colour, suitable for exterior application conforming to IS-15965.

Supply and fixed 605x605 mm aluminium anodised powder coated snap grid ceiling including fixing arrangement for hanging. The suspended false ceiling comprises of aluminium main runner and cross tee of size 24mm x 32mm x 0.30mm and 15mm x 32mm x 0.30mm and suspended with 4 mm dia GI wire hangar fixed with steel dash fasteners or from purlin of roof with butterfly clips hold down etc, including laying 12mm thick mineral fibre perforated board complete all as specified.

Material and labour for plain cement concrete 1:4:8 type D-2 (using 40 mm graded mechanically crushed stone aggregate), as in foundation filling and mass concrete, complete, all as specified and as directed .

SCHEDULE A PART II (INTERNAL ELECTRIFICATION)

Taking down carefully copper/aluminum point wiring light/fan/sockets out let/power point complete (fittings such as switches, sockets, ceiling rose, pendent holders, light fittings etc. are to be measured separately) and/or drawing out from existing conduit/batten and making good disturbed surface of walls/floors/ceiling, complete all as specified and as directed.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable HFFR/ZHFR(Zero Halogen Fire Retardant), 1100 volt grade with multi stranded copper conductor drawn through and including medium grade, ISI marked, mild steel conduit not less than 25 mm dia with accessories, concealed on wall/ceiling and including provision of 1.50 Sqmm single core PVC insulated , unsheathed cable HFFR/ZHFR, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer both internally and externally suitable for housing the flame proof switches, socket outlets, fan regulators etc. with brass screws and brass washers and making good the disturbed surfaces as per existing for one light/fan/bell point controlled by one switch. Note :- (i) Switch, socket and fan regulators to be measured and paid for separately . MS Conduit confirming to IS 9537 part I & III. (ii) All chases will be cut by chase cutter only.

Description all as per Srl item No.2.02 here in before but for socket outlet point 5 Amp on same board complete all as specified and as directed.

Description all as per Srl item No.2.02 here in before but for socket outlet point 5 Amp on Independent board complete all as specified and as directed.

All as per the description of Serial Item No 2.02 above, but with 2.50 Sq mm un-sheathed multistranded cable for one socket outlet 15 Amps independent including continuous copper earth wire, PVC insulated of 2.50 Sq mm size, complete, all as specified and directed. (Switch, Socket shall be measured and paid separately)

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable HFFR/ZHFR(Zero Halogen Fire Retardant), 1100 volt grade with multi stranded copper conductor drawn through and incuding medium grade , ISI marked PVC casing caping not less than 32 mm width , 10 mm depth with accessories fixed on wall/ceiling surface and incuding provision of 1.50 Sqmm single core PVC insulated , unsheathed cable HFFR/ZHFR, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs to sheet metal enclosure and making good the disturbed surfaces as per existing for one point controlled by one switch. Note :- sheet metal enclosure to be measured and paid for separately .

Description all as per Srl item No.2.06 here in before but for socket outlet point 5 Amp on same board complete all as specified and as directed.

Description all as per Srl item No.2.06 here in before but for socket outlet point 5 Amp on Independent board complete all as specified and as directed.

Supply and fixing switch flame proof rotary type with termination box in LM6, 6A, single pole, 250 volt , AC supply, ISI Marked, complete all as specified and as directed.

Supply and fixing socket and plug combined in LM6 cable termination box, 6Amp, 250V, 2P+earth , ISI Marked complete all as specified and as directed.

Supply and fixing epoxy finish LM6 junction boxes aluminium housing with accessories and three cable entriescomplete all as specified and as directed.

Supply and fixing switch piano 5 Amps, flush type, single pole, one way, 230 volt , AC supply, ISI Marked, complete all as specified and as directed.

Supply and fixing socket outlet 5 pin 6 amps, 230 volt. flush type, ISI Marked complete all as specified and as directed.

Supply and fixing switch flame proof, rotary type, with termination box in LM 6, 16 Amps single pole, 250 Volts, AC supply, ISI Marked, complete all as specified and as directed.

Supply and fixing socket outlet flame proof, rotary type, with termination box in LM 6, 16 Amps single pole, 250 Volts, 2P+earth, AC supply complete all as specified and as directed.

Supplying and fixing in replacement fluorescent tube light fitting flameproof type FLP-WP of T5 1X 28W including integal reflector made of aluminium alloy LM61with electronic ballast, bipin holders, connector block, etc. and all accessories internally pre wired including connecting with 3 core copper conductor flexible cable of size 23/0.0076 from ceiling rose to connector of the light all as specified and as directed.

Supply and fixing in replacement, MCB single pole and neutral , 240 volts, 40 Amps, breaking capacity 10KA , ISI marked, complete all as specified and as directed.

Supply and fixing in replacement, MCB single pole, 240 volts, 50Hz , breaking capacity 10KA, C curve 6 to 32 Amps, ISI marked, complete all as specified and as directed .

Supply, insatallation, testing of flame proof SPN distibution board 8 way, double door, IP 43 protection, as per IS 8623 including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles, concealed on the wall surface including taking down the existing DB's any type and description and making good the disturbed portion with adjoining surfaces to match with existing finish complete all as specified and as directed .

Material and labour for earthing with copper earth plate electrode 600mm x 600mmx 3.15mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 20x3 mm copper earth strip as earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire protected by galvanized steel pipe 40mm dia (light grade) and connected to main switch or main control board all as shown in electrical plate No.3 of SSR Part-I & including necessary excavation and earth work. The rate also include charcoal & salt in alternate layers, 20mm dia GI pipe (light grade) for watering and 40mm GI protection pipe, funnel, wire mesh, RCC cover etc. complete, all as specified or indicated including testing on completion. Note : The rates for earth work, GI protection pipe, funnel, wire wesh, RCC cover, etc shall be deemed to be including in quoted rates. RCC cover shall be 50mm thick in 1:2:4 type B-1 using 8mm bars @10cm c/c both way.

Supply and fixing in replacement recess mounted LED circular down lighter, high efficency diffuser , die cast housing,, 240 volt, 50HZ, AC supply , complete with all accessories internally pre wired including connecting with 3 core copper conductor flexible cable of size 23/0.0076 from ceiling rose to connector of the light all as specified and as directed. Make: Havells Cat Part No LHEBLBP71Z1W018 or equivalent model in makes mentioned in Appendix 'B' of tender document

Supply and fixing in replacement of surface mounting LED tube light battern fitting for LED tube light 18 watt, with all accessories, internally prewired and including connecting up using three core copper conductor cable of size 0.50 sqmm from ceiling rose to connector block complete all as specified and as directed. Make: Philips Cat Part No. TMC 501 1XT-LED22WP3241, Wipro Cat Part No. WIO921208, Havells Cat Part No. Regal Batten T8 upto 1x22 SSB SWH or equivalent model in makes mentioned in Appendix 'B' of tender document.

Supplying and fixing in replacement LED energy saving tube light, 18/20 watt with high frequency power factor suitable for surface mounting battern fitting complete, all as specified and as directed. Make: Philips Cat Part No. 20W 865 T8 INDI-2100Lm, Wipro Cat Part No. LL13-181-650, Havells Cat Part No. Crystal 1213 T8DSTL20WLED 865 Glass or equivalent model in makes mentioned in Appendix 'B' of tender document.

Supply and fixing LED Bldg security light luminiare, 40 watt LED pressure, dei- cast housing, with epoxy power coated, dark graphite grey colour finish, prismatic polycarbonate cover, with individual LED lenses including lamp (25 watt LED) complete with all accessories, pre-wired upto terminal block including bracket made up of 1.60m long GI pipe, 25mm dia light grade, bent to required length and fixed to wall with two clamps made of 40x6 mm mild steel flat iron 15cm long, 4 Nos 8mm dia bolts with nuts and connecting with 3 core copper conductor flexible cable from terminal box to the ceiling rose or connector of the light point complete all as specified and as directed. Make : Philips Cat Part No. ENDURAPEARLSL25WLED7575ASYTOPC, Wipro Cat Part No. LR02-291-XXX-57-XX, Havells Cat Part No. ENDURAPEARLNEOSL40CWOMRFGSIPSUGR or equivalent model in makes mentioned in Appendix 'B' of tender document .

Material and labour for sub main wiring with two single core ZHFR (Zero Halogen fire Retardant), PVC insulated unsheathed copper conductor cable 6 sqmm drawn in and including mild steel, medium grade 25 mm dia concealed conduit with accessories on wall or ceiling with one additional PVC insulated, stranded copper conductor ZHFR cable of 6 sqmm, green colour for earth continuity conductor including taking down old unserviceable sub main wiring complete all as specified and directed. Note- 3 run of 6 sqmm cable with concealed conduct shall be measured as 1 unit.

Supply , insatallation, testing of SPN distibution board 08 way,with acrylic double door , IP 43 ,including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles, concealed on the wall surface including taking down the existing DB's any type and description and making good the disturbed portion with adjoining surfaces to match with existing finish, complete, all as specified and as directed. Make: Siemens/ Schenider Acti 9/ Hager Nevello Plus/ Legrand

Note:- Amount of credit of Rs. 74,702.00 for retrieved materials is mentioned in Schedule of Credit Page Nos.106R & 107R of tender documents in pdf form which will be deducted offline while acceptance of tender.

M/s Vridhi Construction Co.

Swami Enterprises

M/s B.S.Jain