Special repair to bldg No P143 SMC at AFS Jodhpur and Provn of acrylic Synthetic flooring work in badminton court at Offr Mess AFS Jodhpur

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each or as directed by Engineer-in-Charge

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing or removing from site to store complete as directed by Engineer-in-Charge.

Supplying and fixing 16 mm of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on wall/ceiling complete all as specified.

Cutting chases stone concrete blocks pinning in making good to facing where required and pointing in CM 1:3 to ends or edge of landing steps cills sunshades shelves lintels eytc and cutting chases for conealed water tuibing making good not exceeding 10 cm girth for stone walls as directed by Engineer-in-Charge

Taking up or down steel tubing 20 mm bore and connections including cleaning for refixing or removing from site to store complete all as specified

Supplying and fixing 20 mm of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on wall/ceiling complete all as specified.

Taking up or down steel tubing 25 mm bore and connections including cleaning for refixing or removing from site complete all as specified and directed.

Supply and laying 25 mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Dismantling of cast iron or reinforced concrete drain pipe including all fitttings and fixtures, jointed in cemented mortar and taking out of trenches or in vertical position of internal dia 100 mm & less all as directed by the Engineer-in-charge.

S&F in repair for PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints laid in trenches or in floors as directed by Engineer-in-Charge

S&F in repair for PVC (SWR) pipes 110 mm dia single socketed, in any length with rubber ring joints fixed in walls as directed by Engineer-in-Charge

S&F in repair for PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints laid in trenches or in floors as directed by Engineer-in-Charge

S&F in repair for PVC (SWR) pipes 75 mm dia single socketed, in any length with rubber ring joints but fixed in walls as directed by Engineer-in-Charge

S&F in repair for PVC (SWR), junction single, (Single T) with door 110 mm dia equal or unequal as directed by Engineer-in-Charge

All as per item No.14.00 here-in-before ,but 75 mm dia as directed by Engineer-in-Charge.

S&F in repair for PVC (SWR) door bends 110 mm dia as directed by Engineer-in-Charge

All as per item No.16.00 here-in-before,but 75 mm dia as directed by Engineer-in-Charge.

S&F in repair for PVC (SWR) Cowl 110 mm dia as directed by Engineer-in-Charge

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing from site and rubbish off the premises as directed by Engineer-in-Charge

M&L for joint free non skid ceramic tiles, coloured, 7 to 8 mm thick in floors etc. area of each tile exc. 0.06 sqm but n. exc. 0.11 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 as directed by Engineer-in-Charge.

M&L for glazed ceramic tiles, coloured, 450x300x7mm thick on vertical surfaces such as skirtings, dados and risers to steps etc, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on stone or brick masonry surfaces as directed by Engineer-in-Charge.

M&L for joint free non skid ceramic tiles, coloured, 7 to 8 mm thick in floors and skirting etc. (square/rectangular) area of each tile n. exc. 0.36 sqm, set & jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 as directed by Engineer-in-Charge

Material and Labour for complete removal of existing treatment of plastered or unplastered surfaces of wall and applying two coat of Acrlic distemper over a coat of primer in any shade or colour as approved by Engr-in-charge complete all as spfd.

Material and Labour for complete removal of existing treatment of plastered or unplastered surfaces of Ceiling and applying two coat of Acrlic distemper over a coat of primer in any shade or colour as approved by Engr-in-charge complete all as spfd.

Material and Labour for complete removal of existing treatment of plastered or unplastered surfaces of wall and applying two coat of Acrlic distemper over a coat of primer in any shade or colour as approved by Engr-in-charge complete all as spfd.

M&L for preparation of old plastered and unplastered surface of walls and applying two coats of weather proof exterior emulsion paint complete all as specified and all as directed

M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint as directed by Engineer-in-Charge

M&L for preparation of old painted wooden surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint as directed by Engineer-in-Charge

Material and Labour for preperation of newly plastered surfaces of wall and applying two coats of Acrlic distemper over 1mm thick wall care putty over a coat of primer complete all as specified and directed by Engr-in-Charge

M&L forpreperation of newly plastered surfaces of walls and applying two coats of weather proof exterior emulsion paint complete all as specified and all as directed

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc completed as directed by Engineer-in-Charge

M&L for rendering 15 mm thick in CM 1:4 on stone masonry surfaces/RCC/Chajja finished even and smooth with/without using extra cement as directed by Engineer-in-Charge.

M&L for rendering 15 mm thick in CM 1:6 on stone masonry surfaces finished even and smooth without using extra cement as directed by Engineer-in-Charge.

M&L 5 mm thick plastering in CM 1:3 finished even and smooth w/o using extra cement on concrete surface of ceilings as directed by Engineer-in-Charge

Material and Labour for preperation of newly plastered surfaces of Ceiling and applying two coat of Acrlic distemper over a coat of primer in any shade or colour as approved by Engr-in-charge complete all as spfd.

S&F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, as directed by Engineer-in-Charge.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, and fixing in the frame at site as per specification & drawing as directed by Engineer-in-Charge

Cutting holes in brick walls in cement mortar for insering holdfasts and making good dismantled portion in cment mortar 1:3 or cment conrete 1:2:4 type B-1 as required exc half brick but not exc one brick as directed by Engineer-in-Charge

M&L for framed work as in door or gates of angle or other section with gusset plate rails braces etc complet drilled for fixing of steel sheeting or other covering . Doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings 9 exclusive of steel sheeting or other covering running rails and guides ) and hanging also fastening and fixing complete grade Fe-290 (Gde E-165) as directed by Engineer-in-Charge

S&F in repair figured glass pin head type 4 mm thick,window and fixed as louvers in ventilators supplied square n.exc. 0.5 sqm in each pane as directed by Engineer-in-Charge.

S&F 200 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed as directed by Engineer-in-Charge

S&F 300 mm long aluminium alloy anodized silding door bolt with hasp staple (bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts and sliding bolts of extruded sections or casr aluminium alloy as directed by Engineer-in-Charge

S&F for 100 mm long butt hinges, medium weight stainless steel as directed by Engineer-in-Charge

S&F aluminium handles, cast type, anodized, of size 150mm as directed by Engineer-in-Charge.

S&F 300 mm, mild steel, ordinary rat tail rod pattern springs including roller and roller plate complete as directed by Engineer-in-Charge.

S&F floor door stopper, with 150 mm long cover plate, of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor as directed by Engineer-in-Charge.

Resecuring or easing & adjusting without taking down shutters of any description exc 1 sqm and n exc 2 sqm each as directed by Engineer-in-Charge

S&F in repairs aluminium handles, cast type, anodized, of size 150mm as directed by Engineer-in-Charge.

S&F in repairs 300 mm long aluminium alloy anodized silding door bolt with hasp staple (bolt type ) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts and sliding bolts of extruded sections or cast aluminium alloy as directed by Engineer-in-Charge

S&F in repairs 200 mm long aluminium, anodized, barrel tower bolts of extruded section and fixed as directed by Engineer-in-Charge.

Welding in repairs exc 2.5 cm & n exc 5 cm in length & thickness of metal n.exc 6 mm all as specified and directed by Engr-in-charge

S & F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of apreture 1.4 mm & fixed with stainless steel wire staples fixed.

S&F in repair 25 mm MS powder coated curtain rod with and including fancy type powder coated MS fixing brackets, stops rollers,decorative finials etc complete all as directed by Engr-in-charge

M&L for hacking out old broken glass (any thickness, size, quality or description) from metal frame glazed with putty including punching or drilling out old glazing pin/spring, clips and providing new ones as directed by Engineer-in-Charge.

S&F sheet glass 3 mm thick, ordinary quality and glazing with oil putty or wooden beads supplied with shutters in square n.exc. 0.5 sqm in each pane as directed by Engineer-in-Charge.

S&F in repair CP tubular towel rail, 20 mm dia, D type, 60 cm long between flanges and all as specified and directed by Engineer-in-Charge

S&F in repair CP grating 100 mm dia all as specified and as directed.

S&F in repair glass corner shelf (set of three) fixed with and including chromium plated brass screws and wooden/plastic cleats and all as specified and as directed.

S&F in repairs, EWC vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device fixed complete all as specified and as directed by Engineer-in-Charge

S& F in repairs PVC board, interior grade 18/19 mm thick , prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber work,or PVC sheet or other place as built up furniture or shelf as specified and as directed,

S&F 75mm size Brass handles, cast type, polished bright for kitchen cabinate complete all as directed

S&F ball catches with 8 mm dia steel ball and brass body and striking plate including letting in and fixed as directed by Engineer-in-Charge

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F in repairs 15 mm bore bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule as directed by Engineer-in-Charge.(Minium weight 15 mm-450 gms)

S&F in repairs, 15 mm bore stop valve, fancy type, chromium plated with long shank and cup , screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions as directed by Engineer-in-Charge.(Minium weight 15 mm-400 gms)

S&F 15 mm bore stop valve, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions as directed by Engineer-in-Charge.((Minium weight 15 mm-450 gms)

S&F in repairs 20 mm dia gun metal globe or gate valve with iron wheel head screwed both ends for iron pipes as directed by Engineer-in-Charge (Minium weight 15 mm-450 gms)

S&F in repair brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union as directed by Engineer-in-Charge.((Minium weight 15 mm-235 gms)

S&F in repairs PVC connection 15 mm size with nuts of length 450 mm as directed by Engineer-in-Charge.

S&F in repairs vitreous china wash basin, white, flat back, rectangular shape size 550x400mm or matching size including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, 15mm bore elbow action pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe PVC connection 15 mm size with nuts of length 450 mm.complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets all as directed by Engr-in-charge.

S&F in repairs single mirror bath room cabinet moulded body and framed (made from strong and fine quality ABS plastic ) with hinged door of size 16 " x 12 " x 6 " white or ivory colour fixed on wall with appropriate rawl plugs . Make : Prayag/Polytuff as directed by Engineer-in-Charge

S&F in repairs brass chromium plated health faucet of 15 mm bore complete as directed by Engineer-in-Charge.

S & F for stainless steel toilet paper holder fixed to walls with chromium plated brass screws complete all as specified and directed.

S&F in repair sink with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm, bowl size 410mm x 330 mm x 160 mm and PVC waste pipe of 32mm bore and of suitable length, all as directed by Engr-in-charge

S&F in repairs 500 litres (ISI marked) capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore plastic ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms) as directed by Engineer-in-Charge

S&F 1000 litres (ISI marked) capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore plastic ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms) as directed by Engineer-in-Charge

S&F PVC (SWR) gully traps of size 125/110 mm,setting and jointing with solvent cement and complete and as directed by Engineer-in-Charge.

S&F in repair for PVC (SWR), 75mm dia of floor trap, with grating including jointing with solvent cement and complete and as directed by Engineer-in-Charge.

M&L for 50 mm thick (average) cement concrete 1:3:6 type C-0 mix (12.5 mm graded stone aggregate) in padding over roof.

M&L for 10 mm thick rendering in CM 1:3 over concrete surfaces (Roof) mixed complete all as specified.

M&L for applying roof treatment on top of roof with APP modified membrane (minimum 3 mm thick) with non-woven polyster reinforcement/mat (centre core) with thermal insulation with white mineral gravel finish on upper side of membrane laid by torch application method with overlaps 100mm on length side and 100 mm on the width side as per manufacturer’s instructions over and including a coat of approved cold applied bituminous oil based primer (IS- 3384) @ 250 gm/sqm over cleaned roof surface complete all as specified and as directed by Engineer-in-Charge.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate in sub floors as directed by Engineer-in-Charge.

S&F EPDM rubber to aliminium window frame for fixing window glass etc including removing and refixing of all fittings and fixtures all as specified and as directed .

S&F slinding window lock consisting of aluminium body with pvc mail and female with necessary screw or fixing arrangment including removing and refixing of all fittings and fixturesall as specified and directed.

Supply and Fix, in repair two way bib tap, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed.

S&F in repairs PVC waste pipe of 32 mm bore of suitable length for WHB/urinal/sink, complete all as specified.

Dismantling boarding, any description, fixed in any position with nails.

S&F 12 mm thick plywood, grade BWR, type BB, fixed with screws to timber frame work

S&F 6 mm thick plywood, grade BWR, type BB, fixed with screws to timber frame work

M&L in repairs 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with srews to timber frame work or as directed by engr-in-charge.

Demolition of brick work or stone masonary built in cement mortar complete all as directed.

M&L for Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6).complete all as specified and as directed.

S&F Urinal, bowl type or half stall pattern, basin only including connections to flushing pipe and outgoing pipes fixed in repairs omplete all as specified and as directed.

M&L 12 mm thick perforated particle board/tiles for insulation and accoustic purpose 60x60 cm in size, fixed with nails to timber frame work or with staples on snap grid in ceiling, flat or sloping including two coats of white colour painting on a coat of primer as as specified and directed by Engr In Charge.

S&F in repair Anodised aluminium snap grid for EPS PVC pannel frame work for false ceiling all as specified

S&F in repair Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold asteners 12.5mm dia. 40mm long complete all as specified

Material and labour for post constructional antitermite treatment of soil under existing floors using emulsion @ one liter per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified & directed

Material and labour for providing and injecting chemical emulsion for post constructional antitermite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed.

S&F exterior single colour aluminium composit panel thickness 3mm to 5mm fixing on wall screws & tap in existing system hieght upto 30 fit incl colour of ACP is as per existing surface complete all as specified & directed by Engr-in-Charge.

M&L for repairs to leakage in existing 15 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple up to 200 mm all as directed by Engineer-in-Charge.

M&L for repairs to leakage in existing 20 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple up to 200 mm all as directed by Engineer-in-Charge.

M&L for repairs to leakage in existing 25 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple up to 200 mm all as directed by Engineer-in-Charge.

S&F in repairs 15 mm bore Elbow action pillar or bib taps, cast copper alloy, chromium plated, screwed down, screwed for iron pipe or for brass ferrule make as per approved by Engrs-in-charge.

M&L for 50 mm thick cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in floors finished with smooth levelled finish using extra cement to receive acrylic flooring complete all as specified.

M&L for 4mm thick Acrylic Synthetic flooring in two layer incl Colour line marking complete all as specified.

M&L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor over and including 15mm thich cement screed bed or bedding in CM 1:6.

M&L for 25 mm thick cement concrete 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in floors rough finished complete all as specified.

All as per item No 109.00here-in-before but as in skirting over 10mm thick backing coat of CM 1:4

Taking down carefully copper/aluminum point wiring (Light/ fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc, stacking at site for reuse or removing materials to store for keeping in for taking credit and making good the disturbed surfaces / walls/ floors etc,.

M&L for point wiring with 1.5 Sq. mm, multi-stranded copper conductor,FRLSH, single core, PVC insulated and unsheathed cable for phase and neutral, including 1.5 Sq. mm PVC insulated unsheathed multistranded copper conductor single core cable as earth continuity conductor (in green color) connected to common earth dolly, drawn in surface/concealed /Casing Caping /conduit heavy duty (HMS Grade), GI terminal boxes not less than 1.0mm thick fixed flush to wall surface, covered with & including 3 mm thick plastic laminated sheet top cover or including modular plates of required size for mounting switch and sockets etc. complete all as specified and directed for following : - Note : Quoted rates deems to be included cost of grooves cuting and modular plate for mounting switches, sockets & regulators as required at site.

One light point controlled by one switch one way.

One fan point controlled by one switch one way.

One 3 pin 5 Amp switch & socket outlet on same board with other switches.

One 3 pin 5 Amp switch & socket outlet on Independant board.

One bell point controlled by one switch 5 Amps bell push.

All same as per item ser No 113 here-in-above but wiring using 2.5 sqmm multi-stranded copper conductor, FRLSH, single core, PVC insulated and unsheathed cable, including 2.5 Sq. mm PVC insulated unsheathed multistranded copper conductor single core cable as earth continuity conductor (in green color) connected to common earth dolly for 6 pin, 15/16 Amps socket outlet on independant board.

All same as per item ser No 113.00 here-in-above but wiring using 4.0 sqmm multi-stranded copper conductor, FRLSH,single core, PVC insulated and unsheathed cable, including 4.0 Sq. mm PVC insulated unsheathed multistranded copper conductor single core cable as earth continuity conductor (in green color) connected to common earth dolly for two pin earth metal clad plug & socket point for AC/Geysers.

S&F switch modular single pole one way 6 Amps 230 volt 1 module.

S&F switch modular single pole one way 16 Amps 230 volt 1 module.

S&F Socket modular 6 Amp 2/3 pin combined two module.

S&F Socket modular 6&16 Amp 2/3 pin combined two module.

S&F Bell Push modular single pole one way 6 Amps 230 volt 1 module.

S&F Stepped type modular electronic fan regulator, switch size, flush type 230V AC.

S&F Ceiling rose Modular surface bakelite 65x50mm three terminal.

S&F Lamp holder modular insulated PVC/Polycarbonate/bakelite body, fixed on PVC round or squre box using necessay screw & gutti complete all as specified.

S&F electronic Bell Bul-Bul music, 230 volt, single phase.

Taking down carefully Ceiling fan/Exhaust fan by disconnecting electrical connections, unsecrewing from position, dismantling blades, stacking carfully at site for reuse of serviceable fans complete all as directed and specified.

Taking down carefully Electric geyser by disconnecting electrical connections & water connections unsecrewing from position, stacking carfully at site for reuse of serviceable geyser all as directed and specified.

Fixing only light fitting any type, connecting up with twin core PVC insulated and PVC sheathed flexible copper conductor cable of suitable size from ceiling rose complete all as specified.

Supply and fixing LED light fitting wall /roof mounted, Aluminium housing, 1 x 20 watt including LED tube with driver complete suitable body robust, corrosion resistant, superior finish and without any cracks or through holes. The system wattage of fitting should not be more than 20 watt ± 10%, surge protection of minimum 2 kV power factor should be more than 0.90 cool white colour, total harmonic distoration (THD) should not be more than 15%, lumen output should not be less than 90 lumens per watt, total input voltage range 140-280 V AC, colour rendering index should not be less than 80, corelated colour should be minimum 6000 degree kelvin complete all as specified and directed.

Supply and fixing LED light fitting wall /roof mounted, Aluminium housing, 1 x 9/10 watt including LED tube with driver complete suitable body robust, corrosion resistant, superior finish and without any cracks or through holes. The system wattage of fitting should not be more than 20 watt ± 10%, surge protection of minimum 2 kV power factor should be more than 0.90 cool white colour, total harmonic distoration (THD) should not be more than 15%, lumen output should not be less than 90 lumens per watt, total input voltage range 140-280 V AC, colour rendering index should not be less than 80, corelated colour should be minimum 6000 degree kelvin complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 15 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete Make -Philips model no-340349(JOJOBA WALL LIGHT) or equivalnet make mentioned in appendix "B".

S&F Building security light fittings, with pressure die cast aluminium housing, suitable for 25 W LED, complete pre-wired, incl suitable bracket for fixing light on wall or any indicated locaction all as specified and as directed by Engr - in Charge complete all as per Havells Cat No: ENDURAPEARLSL25W or equivalent model approved makes.

S&F LED light fitting 1 x 10W bulkhead luminaires including inbuild LED light driver perfect interior and exterier application connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

M&L for cutting holes 300mm diameter for preaparing opening through wall for fixing exhaust fan 300mm sweep, making good to damaged surface of wall, make a smooth circular surface and match with specification of existing wall all as directed by Engr-in-charge at site

Hanging only ceiling fans, 1200mm sweep, complete with three blade, down rod, accessories and making connection from ceiling rose or connector to fan using three core 0.75sqmm copper stranded conductor PVC insulated and PVC sheathed flexible wire complete all as specified.

Fixing only exhaust fan 300mm sweep, Steel/PVC body AC single phase 230V of size 300m using 4 Nos 10mm x 100mm long wall fasteners, nut and washers and connecting up using flexible three core 0.5sqmm copper stranded conductor PVC insulated and PVC sheathed flexible wire through PVC flexible conduit from ceiling rose/connector to fan complete all as specified.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as per crompton cat ref no. LCTLR-36-FO-CDL or equivalent in approved makes.

Installation only Electric Storage type water heater (Geysers) 25/50 Ltr capacity with standard fixing accessories including suitable size wall fastener bolts & Nuts, gutties etc complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor(BLDC) connecting up including provision of flexible PVC conduit from ceiling rose or connector to fan to cover PVC cable including marking of MES number and fixed in position as recommended by manufacturer complete all as specified.

S&F Exhaust fan 300 mm sweep, copper wounded, four blade, metal body, BEE approved/ISI marked, air delivery shall not be less than 230 CFM, mounted in suitable opening arrangement with louvers shutters, suitable for operation on 240 volt, single phase, 50 cycle per second, AC supply and connecting up using flexible cord wire 3 core using PVC flexible conduit from ceiling rose or connector to fan to cover PVC cable including marking of MES number and fixed in position as recommended by manufacturer complete all as specified.

M&L for Sub main wiring as per IS, single core FRLS PVC insulated flexible multistranded copper conductor,FRLSH, 1.1 KV grade drawn through & including PVC grey conduit heavy duty with necessary accessories (like bend, juction boxes etc) including taking down old unsv submain wiring complete all as specified for Two runs of 6.0 Sq.mm main Phase-Neutral supply cable alongwith one run of single core 6.0 Sq.mm for continuous earth wire in green color.

M&L for Sub main wiring as per IS, single core FRLS PVC insulated flexible multistranded copper conductor,FRLSH, 1.1 KV grade drawn through & including PVC grey conduit heavy duty with necessary accessories (like bend, juction boxes etc) including taking down old unsv submain wiring complete all as specified for Two runs of 10.0 Sq.mm main Phase-Neutral supply cable alongwith one run of single core 10.0 Sq.mm for continuous earth wire in green color.

Supply and fixing sheet metal enclosures with socket plug top, and MCBs single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB upto 16 Amps, 240 Volt capacity fixed flush to wall surface including making good to damaged surface of wall to match with existing specification and tested on completion complete including taking out old all as directed.

Supply and fixing sheet metal enclosure distribution board for 240 volts, 8 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete including taking out old all as directed.

Supply and fixing sheet metal enclosure distribution board for 240 volts, 12 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and blank plates and fixed flush in wall surface, and tested on completion complete including taking out old all as directed.

Supply and fix Sheet metal enclosure distribution board TPN, 415 volts, 4 way Horizontal/vertical type as per site requirement, double door type, 200 Amps rated neutral copper bus bar for housing MCBs, blank plates and including provision for fixing TPN MCB as incommer, DB fixed flush or in wall surface including making good to damaged surface of wall to match with existing specification complete including taking out old all as specified all as specified and directed.

M&L for MCB TPN/FP, 63 Amps 415 volts, 10 kA rupturing capacity providing in DB complete including connection & testing all as specified.

M&L for MCB SPN/DP 40 to 63 Amps 240 volts, 10 kA rupturing capacity providing in DB complete including connection & testing all as specified.

Supply and fixing MCB single pole 6-32 Amps, 240 volts, 10 kA rupturing capacity providing in DB complete including connection & testing all as specified.

M&L for wiring with TV coaxial RG-06, electrolytic grade solid annealed copper conductor having single strand of 0.7 mm dia, PVC insulated, aluminium foiled and aluminium wire braided, overall PVC sheathed cable complete including concealed PVC conduit 20mm dia from TV Socket to dish antena on roof of building complete all as specified. Note : 20mm conduit pipe inside building shall be concealed in wall surface and from external surface duly fixed with GI Saddles is deems to be included in quoted rates.

Material and labuor for earthing complete with Galvanized Steel earth plate electrode 600x600x6mm thick buried directly in ground (earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 M below normal ground level and filled with 15cm thick alternate layers of charcoal and salt, connected & including GI wire earth lead 4.0mm dia by means of bolts, nuts, check nuts and washers made of galvanized iron protected by 15mm dia GI Pipe (light grade). Earth plate shall be surrounded by alternate layers of charcoal or coke and common salt in 15cm thick in layers & 15cm of widht all aurround of earth plate including 20mm dia GI light grade pipe for watering and including funnel, wire mesh, necessary earth work in any type of soil, Pre-cast RCC cover duly re inforced with 8mm dia TMT Bar @150 mm c/c both ways, one lifting handle made of 8 mm dia TMT bar embedded in cover slab, Earth Pit of PCC (1:3:6) type C2 (using 20mm graded crushed store aggrgate) complete all as specified and as shown in electrical plate No-3 of SSR Part-I including testing on completion. Note:- (i) PCC chamber shall be constructed at least 1.5 metre away from the earth electrode and pipe for watering shall be provided in slanting manner. (ii) The unit rate includes earthing lead & protection pipe upto 7.5 metre from top of earth plate.

NOTES FOR LED LIGHT FITTINGS & BULBS : (i) All LED light/luminare shall meet the provision laid down in IS - 16101, 16102 Part-I/II, 16103 Part-I, 16104, 16105, 16106, 16108/2012 and 15885 Part -II / Section 13. (ii) Contractor shall submit test report of LED street light fitting from Government accredited test laboratory for LM-79 and LM-80. (iii) Contractor has to furnish a replacement warranty of 02 years for LED light fittings complete including lamps from the date of completion of contract. The product will be replaced on site free of cost in the following case :- (a) Manufacturing defects. (b) Failure due to mechanical and electrical impact. (c) Drop in lumen (or lux at 1 m) below 90% of claimed values of lumen (or lux at 1 m) of the LED /Luminaries.

M/S KAUTILYA GARG

M/s Deepshikha Trading Corporation

JAMWAY MATA CONSTRUCTION COMPANY

VIKAS CONSTRUCTION CO.

DEV INDUSTRIES

M/S BUDHRAM BISHNOI

Nikhat nirman