Construction of Different Anganwadi Centre /PKG-11/ at Ta.Kalol, Dist.Gandhinagar (1) Piyaj-1 (Hajipur) (2) Vadnagar Pura(Chhatral)

Excavation for foundation upto 1.50mt.Depth including sorting out and stacking of useful materials

and disposing of the excavated stuff as directed with in all lead & Lift (A) Loose or Soft soil.

Excavation for foundation upto 1.50mt.Depth including sorting out and stacking of useful materials

2 and disposing of the excavated stuff as directed with in all lead & Lift (B) Dense or Hard soil. 17.40 Cu.m 157.16

Filling foundation and plinth with sand under floors including watering, ramming and consolidating

dressing etc, comp.

Filling available excavated earth excluding rock in trenches plinth side of foundation etc. in layer not

4 exceeding 20cm. In depth consolidation each deposited layer by ramming and watering. 50.04 Cu.m 136.92

watering, ramming and consolidating etc. comp.

Applying general insecticide pest control treatment to floors, cupboards etc including labour materials

etc. complete. Using Imidacloprid 30.5 SCas Per IS 6313 part - II( (0.075% concentration by mass) is

6 recommended 10.5ml chemical diluted with 5 liters of water application 0.5 litre chemical /Sqm of 86.00 Sqm 91.63

surface is recommended as per I.S

Providing and laying cement concrete 1:2:4 (1- Cement : 2- Coarse sand : 4- graded stone aggregates

7 20 mm nominal size) and curing complete including cost of formwork in (A) Foundation and Plinth 5.20 Cu.m 4365.22

Providing and laying cement concret 1:1.5:3 (1 Cement : 1.5 coase sand : 3 graded stone aggregrate

8 20mm nominal size) and curing complete exculding cost of form work and reinforcement for 5.80 Cu.m 5457.03

reinforced cement concrete work in (a) Foundation footing base of column and mass concrete

Providing and laying nominal cement concrete M-200 in R.C.C. 1:1 1/2 :3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in

column Upto plinth level.

Providing & laying cement concrete 1: 3 : 6 ( 1 Cement : 3 Coarse sand : 6 graded B.T stone

10 aggregate 20mm nominal size) Curing comp. including cost of form work in foundation and plinth. 24.00 Cu.m 3396.68

Providing and laying nominal cement concrete M-200 in R.C.C. 1:1 1/2 :3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

11 complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in 4.60 Cu.m 10331.36

column for All Floor

Providing and laying nominal cement concrete M-200 in R.C.C. 1:1 1/2 :3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

12 complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work (c) 6.20 Cu.m 6285.23

PLINTH BEAM

Providing and laying nominal cement concrete M-150 in R.C.C. 1:2 :4 (1 cement : 2 coarse sand :

13 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing complete 6.40 Cu.m 4499.55

including the cost of form work but excluding the cost of reinforcement for R.C.C. work PLINTH

Providing and laying nominal cement concrete M-200 in R.C.C. 1: 1 1/2 : 3 (1 cement :1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

14 complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in 6.20 Cu.m 6964.03

BEAMS For All Floor.

Providing and laying nominal cement concrete M-200 in R.C.C. 1: 1 1/2 : 3 (1 cement :1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in

LINTELS All Floor.

Providing and laying nominal cement concrete M-200 in R.C.C. 1: 1 1/2 : 3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in

CHHAJJAS All Floor.

Providing and laying nominal cement concrete M-200 in R.C.C. 1: 1 1/2 : 3 (1 cement :1 1/2 coarse

sand : 3 graded stone agregate 20 mm. Nominal size) including finishing smooth with curing

complete including the cost of form work but excluding the cost of reinforcement for R.C.C. work in

slabs for All Floor.

Providing T.M.T. bar FE500/500D reinforcement confirmed to for R.C.C. work including bending,

18 binding, and placing. In position comp. Up to floor two level. For All Floor 6060.00 Kg 77.29

Brick work using common burnt clay building bricks having crushing strength not less than

19 Kg./Sq.m. in foundation and plinth in cement mortar 1:6 (1 cement:6 fine sand) (b) Conventional. 22.00 Cu.m 4214.09

Brick work using common burnt clay building bricks having crushing strength not less than 35 Kg./

20 Sqm. in cement mortar 1:6 ( 1 cement : 6 Fine sand ) in super structure above plinth level upto floor 42.00 Cu.m 4502.81

two level ( for G.F ) Conventional

Half brick masonary in common burnt clay building bricks having crushing strength not less than

35kg./sq.cm. in cement mortar 1:3 (1 cement : 3 coarse sand ) with 2nos. of 6mm dia mild steel round

bars every three coarse embedded in cement mortar in superstructure for Ground floor

(Conventional)

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Providing and fixing door Single shutter having factory fabricated std. Extruded aluminium colour

anodized hollow section {Section 63.50 x 38 mm x 2.50 mm thick } for door frame, hollow portion

of door frame shall be filled with wood to be insert for durable grip of door hinges, with factory

22 made 38 mm.thick flush door both side pre laminated with 6 Lever Mortice lock , SS Aldrop 30cm 11.40 Sqm 6386.23

long, SS Handle size 15 Cm Long, Tower Bolt size 20 cm etc. as per detail colour & pattern approved

by this office including necessary anodized alluminum fixtures and fastenings.

Providing and fixing Anodized Alluminum Section Jindal Deluxe Sliding Window System C (20mm)

series sction memebers THREE track window section bottom track 21651, frame top & side

23 shutter frame top rail 20530, bottom rail 20529, side rail 20544, lock rail 20531 with 5mm thick 9.60 Sqm 3903.65

transparent plain float glass, with transparent silicon sealant with allu. anosized coated fittings and

fixture etc complete

Providing and fixing standared extruded of alluminium section of size 63mm x 38.10mm x 1.2mm @

Wt. 0.643 Kg/mt) with colour anodized alluminium frame for ventilation with 5 mm thick frosted

24 glass as details etc complete for Ventilation {Colour as directed by Engineer in charge except black & 8.40 Sqm 1175.56

Alluminum section and glass

Providing and fixing Safty grills of required pattern for windows 12mm dia M.S. round Bar at

required spacing M.S. Flat 25mm x 5mm thick as per design and hold fasting with coach bolts

25 including one coat of primer and Shall be Painting with Enamel Paint and Colour approved by as per 360.00 Kgs 111.40

site Engineer etc complete.

Providing and laying Machine cut, Free edges, Machine polished Granite stone slab 18 mm thick

{Single piece not more than 150 cm } for stair steps and riser as per design incl. full moulded round

26 front edge & 1 cm nosing & necessary groobe on trade of steps laid on 20 mm thick cement mortar 26.00 Sqm 3280.48

1:6 (1 -cement : 6 coarse sand ) jointed with grey cement slurry including rubbing and polishing etc.

Providing and laying Both side mirror polished Granite stone slab 18 mm (Average) thick of

27 approved quality incl. full moulded round front edge fixed in wall for Shalves and jointed with grey 12.00 Sqm 1968.49

cement slurry including rubbing and polishing etc. complete

Providing and laying 60 x 60cm Soluble Salt Vitrified tiles 8 to 10 mm thick with pattern colour &

Shade as detailed approve by architect ( 10% Dark colour tiles Pattern ) in flooring treads of steps

and landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand) finishing with

flush pointing in white cement.

Providing and laying 60 x 60cm Soluble salt Vitrified tiles 8 to 10 mm thick with pattern colour &

Shade as detailed approve by architect ( 10% Dark colour tiles Pattern ) in skrting risers of steps and

dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement

Providing and laying 30cm x 30cm in size Ceramic tiles 6mm thick in flooring treads of steps and

30 landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) finishing with 4.00 Sqm 1017.30

flush pointing in white cement

Providing and laying 30 x 60Cm size premium printed glazed tiles 6mm thick in skrting risers of steps

31 and dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed with white cement 24.00 Sqm 1074.00

Provding and filling the joint with epoxy grout 3 mm width and 8 to 10 mm deep, including cost of

32 necessary materials, PVC spacers, filling grout and cleaning etc complete as directed by engineer in 28.00 Sqm 40.40

charge. { Colour and Pattern as directed by engineer in charge.}

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block 60mm thick with

grade of concrete M300 pnumatic compressed / vibrated mechanically and as per approved design

33 Confirming to IS 15658 : 2006 including 35 mm Sand layer for levelling and filling the joint with 32.00 Sqm 706.90

sand in proper line and level as per guidlines of IRC : SP 63-2018 etc. Complete

Providing and laying water proofing tretment with chaina mosaic tiles flooring over avg 40 mm

C.C. 1:2:4 ( 1 Cement, 2 sand, 1 Kapchi 20mm + 3 grit 6mm to 10mm ) bedding for maintaining

slope for plain and curve surface & 12 mm to 20 mm of broken piece of ceramic / glazed tiles ( one

or more color as directed ) to be laid over cement mortar bedding of C M 1:3 (1 cement : 3 sand )

34 containg one Kg. of water profing materials per bag of O P C at plain or / and slops and to be 130.00 Sqm 1102.92

tempered to bring mortar ceramic up to surface with using white cement and colour pigment

including rounding of junctions and extending them up to 15 cm along the wall and curing with

bends any pattens or design as per drawing and cleaning by using oxalic acid etc complete.

Providing and laying Mirror polished Machine polished Grenite stone slab 18mm (Average ) thick for

doors & windows sill & Jams clading as per design including full moulded round front steps & 1cm

35 nosing & necessary groove on trads of steps ;laid on 20mm thick cement mortar 1:6 ( 1 cement : 6 16.00 Sqm 3395.62

coarse sand ) jointed with gray cement sluury including rubbing and polsihing etc. complete.for

Doors / windows sill & jams clading.

Providing 20 mm thick double coat mala cement plaster on interior brick / concrete work for

plastering comprising of base coat of 12 mm thick cement plaster in cement mortar (1 Cement :

coarse sand) in rough finishing and 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 Coarse

sand) finished with trovel including scaffolding curing etc. complete. For Ground Floor

Providing 10mm thick cement plaster in single coat on brick/concrete walls for interior plastering

37 upto floor two level and finished even and smooth in (i) Cement mortar 1:3 (1-cement:3-sand) 88.00 Sqm 211.98

including finishing with a flating coat of neat cement slurry etc. complete. for Ground Floor

Applying two coats of putty & two coats of primer of approved brand and manufacture on new wall

38 surface to give an even shade including thoroughly brushing the surface free from mortar dropping 206.00 Sqm 40.59

and other foreign matter and sand papered smooth.

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Wall painting one coats of primer of approved brand (three coats) plastic emulsion paint of approved

brand and manufacture on undecorated wall surface to give an even shade including throughly Sqm

brushing the surface free from mortar droppings and other foreign matter and sand papered smooth.

Wall painting with Applying two coats of putty & two coats of primer of approved brand & (three

coats) with plastic emulsion paint of approved brand and manufacture on undecorated ceiling surface

39A to give an even shade including throughly brushing the surface free from mortar droppings and other 88.00 Sqm 124.28

foreign matter and sand papered smooth.

20mm thick sand faced cement plaster on walls upto height 10 metres above ground level consisting

of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick finishing coat of C.M.

40 1:1 (1-cement : 1-sand) with 1cm x 1cm groovs as per pattern sample approved by the engineer 236.00 Sqm 315.69

incharge etc. complete.

Providing laying and jointing in true line and level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the

41 help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings 30.00 Rmt 72.65

etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of

all materials.

Providing laying and jointing in true line and level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the

42 help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings 40.00 Rmt 91.84

etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of

all materials. [B] 25mm dia.

Providing laying and jointing in true line and level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer In Charge. Pipe shall be fixed on the wall with the

43 help of clamp at every two metre C/C or shall be concelled as directed including necessary fittings 20.00 Rmt 148.12

etc. including testing of pipe and joints and fixing the same with adhesive solvent, including cost of

all materials.[D] 40 mm.

Providing and fixing uPVC Heavy Duty Handle valve of aprroved brand and Quality with required

44 fitting and adhesive incl. fixing the same with new pipe line as directed by engineer in charge. (B) 2.00 Nos 469.65

25mm dia.,

Providing and fixing uPVC Heavy Duty Handle valve of aprroved brand and Quality with required

45 fitting and adhesive incl. fixing the same with new pipe line as directed by engineer in charge. (C) 2.00 Nos 685.79

40mm dia.,

Providing, laying and jointing in true line and level 75 diametre U.P.V.C (Type B) conforming to IS

13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI

14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other

46 with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 4.00 Rmt 756.22

149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as

directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints

and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing to wall ceiling and floor 10.0 Kg. F/Cm2 working pressure poluthene pipes of

47 the following outside Dia. Low densidy, complete with special flange compression type fittings, wall 18.00 Rmt 338.95

clipsetc. including making good the wall ceiling and floor.(A) 110mm dia.

Providing, laying and jointing in true line and level 110 diametre U.P.V.C (Type B) conforming to IS

13592-1992 with one end plain and other end socketed with rubber ring, & fittings conforming to ISI

14735-1999 of approved make for drainage system pipe line, pipe shall be jointed with each other

48 with rubber lubricant, pipe shall be fixed on wall using of PVC clamp of the size 110 mm diametre x 10.00 Rmt 876.90

149 mm length x 145 mm heigh at every 2000 mm center to center or shall be concealed in walls as

directed including necessary fittings such as bends, shoes etc. including testing of pipes and joints

and jointed with adhesive solvent cement including cost of all materials.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter with jali of the

49 following nominal diameter of self cleansing design with C.I scread down or hinged grating including 6.00 Nos 599.64

the cost of cutting and making good the walls.

Providing and fixing screw down quarter turn heavy duty bib taps of following size (A) Brass

chromium plated screw down bib tap (i) 15mm dia. ( Plumber, Mark, Escco or equivalent brand )

Providing and fixing CP brass Quarter turn pillar tap, capstan head screw down high pressure with

51 screw, shanks and back nuts (A) 15 mm dia {Jaquar< Plumber, Mark Long pipe or equivalent brand} 4.00 Nos 308.73

Providing and fixing wash basin with pedestal of std. Height with single hole for pillar tap with C.I or

M.S brackets painted white including cutting cutting holes and making good the same including C.P.

52 brass waste and waste pipes and bottal trap (A) Vitreous China: (ii) Flat Back washbasin 550 mm x 2.00 Nos 1849.31

400mm size.In colour.

Provision and fixing water closet squatting orissa type W.C. pan size 580mm integral footrest and

53 100 mm P or S trap and in cluding 25 mm dia CP brass flush valve and GI inlet connection etc. 2.00 Nos 1306.94

comp. (A) Vitreous china long pattern white or color

Providing erecting and fixing double coated 4-layer tough virgin plast ISI water tank of required

54 capacity each with all necessary fittings and connection etc. complete on terrace. 2000.00 Litre 10.61

Providing and fixing 600mm x 450mm bevelled edge mirrror of superior glass mounted on 6mm thick

55 A.C. sheet or plywood sheet and fixing to wooden pluge with C.P. brass screws and washers. 2.00 No 859.41

Providing and fixing C.P. brass towel rail comlete with C.P. brass brackets fixed to wooden plugs

56 with C.P. brass scews.(B) 600mm x 20mm size. 2.00 No 616.42

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Providing and fixing S.W. gully trap with C.I. grating brick masonry chamber and water tight C.I.

57 cover with frame of 300mm x 300mm size (inside) with standard weight.(i) Square mouth traps.(B) 2.00 No 1246.92

150mm x 100mm size P of R type

Providing and fixing CP brass screw down stop cock of approved quality 15mm size with adjustable

58 wall flange..or as per instrction of engineer incharge. 8.00 No 205.83

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with

briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light

duty) 455mm x 610mm intenal dimensions, total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse

59 sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick 6.00 No 2932.93

with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete

etc. complete.(i) Inside dimensions 455mmx 610mm and 450mm deep for single pipe line.

Constructing brick masonry chamber for underground C.I. Inspection chamber and bends with

briocks having croshing strength not less than 35Kg. Cm2 in C.M. 1:5 C.I. cover with frame (Light

duty) 455mm x 610mm intenal dimensions total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse

sand :4-graded stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick

with cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and bed concrete

etc. complete.(ii) Inside dimensions 500mm x 700 mm and 450mm deep for pipe line with one or

two inlets.

Providing sock pit of 8.00 Cmt. Volume including excavating and filling brickbats with dry masonry

61 work at top for 45cm. height including covering the top with stone including providing vatas in C.M. 2.00 No 26526.64

1:3 with finishing curing etc. complete as directed.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) to give an

62 required shape even shade after thoroughly brushing the surface to remove all dirt, and remains of 236.00 Sqm 120.26

loose powdered materials.etc complete

Constructing Sandwitch Platform of 18 mm thick Polished Black Granite at top and 25 mm thick

Kota stone slab using cement mortar 1:3 for sandwich and fitting at bottom & edges with waterproof

rigid adhesives including macking necessary grooves in walls with Vertical Kotastone 30 mm x

63 No sandwitch thick every 60 cm centre to cenre including all labour material of approved quality 6.00 Sqm 5868.10

incl. full moulded round front edge fixed in wall for partition and jointed with grey cement slurry

including rubbing and polishing etc. complete

Providing and fixing stainless steel kitchen sink glossy ASIS 304 grade and 1 mm thick with overall

size 510mm x 432mm x 330mm deep having bowl size 410mm x365mm x 165mm of Nirali or

64 equivalent brand with all fittings CI or MS brackets painted white or fixing on stone base including 2.00 Nos 1789.72

cutting holes and making good the same brass valve and fisher union fitting including all necessary

Providing thoruting or plaster drip and moulding to R.C.C. chhajja. Rmt

Writing letter or figures on any surface with black Japan paint (stops, comas, hyphens and the like not

66 to be measured and paid for separately) (ii) Indian (Letters/Figures) 6000.00 Nos 3.68

Providing water harvesting pit 2.40 mt dia x 2.40 mt depth with excavation in any strata filling the pit

with brick bats in 0.60 mt depth, 0.30 mt with 25mm to 40mm kapchi 0.30 mt with 10mm to 20mm

67 kapchi & 2.00 mm depth with coarse sand in layer including maing the lines (PVC) for water inlet 2.00 Nos 26189.30

etc. as directed including 250mm dia bore work with 6" PVC" pipe upto 35mt etc, comp.

Supplying & installing of Dry Chemical Powder type 6 Kg. Capacity fire extinguisher as per I.S.

68 ISI. Mark with necessary fittings etc. complete. 4.00 Nos 2626.00

Providing and fixing 90 cm high Stainless steel railing made from anticorrocive S S pipe of 50 mm

dia (16Gauge) as hand rail with S S 38 mm dia (16Gauge) as a vertical support fixed in RCC slab at

69 1.2m c/c including three horizontal S S pipes of 25 mm dia (16Gauge) at eqal distance fixed by 6.80 Rmt 3245.13

18.75 mm dia (16Gauge) S S pipe including accessories as per detailed drawing as directed etc.

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length , in below

type of pipe erected with 6A Modular type switch / bell push & accessories and earth continuity of

70 following type, erected on PVC / Metallic/ Wooden box, single mounting base frame covered with 50.00 Pt. 419.15

extured/ metallic/ white front plate modules erected on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector as directed.

(a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both are of .ISI marked

1.1 KV Grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of

pipe erected with 6A Modular type switch and hum free EME step type electronic fan regulator

71 mounted and accessories with earth continuity of following type erected on PVC / Metallic/Wooden 6.00 Pt. 598.93

box, single mounting base frame covered with textured/metallic/white front plate modules erected on

/ in wall / ceiling as per pipe erected. with necessary ceiling rose / H.D.Connector as directed. (a) with

medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are of ISI marked

KV grade FRLS PVC insulated multi strand copper wires up to 10 mtr length, in below type of pipe

erected complete with Modular type switch & 5 pin Plug erected on PVC / Metallic/Wooden box

covered with appropriate front plate modules erected on / in wall / ceiling as per pipe erected with

following type of accessories. [I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from

nearby switchboard/mcb db board

(a) with medium class Rigid PVC pipe and accessories erected flushed on wall/ceiling complete

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame covered with textured / metallic/white front plate

73 modules erected on / in wall / ceiling with following type accessories , Cat. III. 4.00 Pt. 241.39

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with necessary PVC fittings & Junction boxes fixed with

adhesive solution & Clamps with following dia of pipes, in approved manner as directed Meter

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected concealed in /flushed on wall/ceiling, with

75 sq. mm copper conductor FRLS PVC insulated stranded wire of green colour for earth continuity of 100.00 Meter 78.78

following size (A) With medium class Rigid PVC pipe and accessories. (b) 2 wire 2.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be erected in / on wall / ceiling with 2.5 sq. mm copper

76 conductor FRLS PVC insulated stranded wire of green colour for earth continuity of following size 60.00 Meter 107.06

(A) with medium class Rigid PVC pipe and accessories (a) 2 wire 4 sq. mm

Providing & erecting Sheet Steel Powder Coated MCB Distribution Board Flush/Surface Mounted

Fitted With Busbar Netural Link Earth Bar and Din Rail Confirming to BS: 5486-1986 without MCB

77 to House Appropriate Nos of MCBs. 2.00 Each 326.23

(F) Single Phase 8 Way Double Door CAT-III

Providing and erecting Miniature circuit breaker single pole 6A to 25A suitable to operate on 240 V

A.C. system and having breaking capacity 10 KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark (A) 6 to 32 Amp. CAT-III

PROVIDING AND ERECTING DOUBLE POLE MCB ISOLATOR A.C.22 DUTY CONFIRMS TO

IS13947-3 240V 40 IN EXISTING BOX. CAT-III

Approved Make ELCBs/RCCBs Conforming to IS12640 and Having Sesitivity of 30Ma and Short

Circuit Withstand Capacity of 6KA and Suitable for Operation on Single Phase 240V Having

Characteristic of Quick Action & Tripping with All Advance Feature & Do not Incorporate any Each

electronic component for Following Max Rating Erected as Directed (ii) 40AMPS.DP CAT-III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to 0.5 Watt assembled on

single MCPCB, with housing used as a heat sink shall be made of thick sheet Steel conforming to IS:

513/CRCA/ aluminium die cast powder coated and high U.V. & corrosion resistance with diffuser

with company mark/name 160V to 270V, Power Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have shown ranges of

ranges shown.) (A) Tube Light with integral driver (iv) 22-24 Watts, Surge - 2KV,IP-20, conventional

Supplying and erecting led lamps with following wattage capacity of 220 to 240 voltage, minimum

15000 burning hours life, 500 V in built-surge protection,Polycarbonate diffuser, mounting suitable

82 for E14 / E27 / B22 lamp holders, pf >= 0.5 (ii) 5 to 8 watts 4.00 Each 112.11

Providing and erecting Approved make Ceiling fan with double ball bearing ISI mark with condenser

A.C. 23OV.50 c/s.1200 mm. sweep complete, canopy erected on existing hook or clamp with

earthing. [Make shall be approved by Engineer in charge]

Providing & erecting Switch board for Computer or electric apparatus consisting of following

modular type accessories mounted with PVC / Metallic concealed/open box with single mounting

base frame covered with textured/metallic /white front plate,modules erected with necessary

connections as directed

84 1 no. 6A/16A universal plug-switch combined. 4.00 Each 1081.71

3 nos. 6A Switch

3 nos. 6A 5 pin Plug For Modular Type Accessories

Decorative call bell Ting-tong box type 250 volts complete erected

Providing and erecting Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe with

necessary coupling buch buried in specially prepared earth pit & G.I. earth wire of 8 SWG erected &

86 connected as directed (For panel) 2.00 Each 823.15

For using salt and charcoal / coke as required for pipe type earthing.

No Rate In

Description of Item (with brief specification and reference to book of specifications) Quantity Unit Amount

MGVC Ltd. meter connection charges

Total Tender amount

Rupees Twenty Five Lakh Fifty Nine Thousand Six Hundred Seventy Four And Paise Eighty Six Only

I/am we/are willing to carry out the work at _____% above /below _____________ percent (should be written in figures and words) of the estimated rates mentioned above. Amount of

my/our tender works out as under.

* Estimated amount put to tender

Deduct :_____ % Below Rs.________________ Add :_____ % Above Rs.________________

Net Rs. ______________________ Total Rs. ______________________

In words ___________________________ In words __________________________

1. The Contractor Shall Exhibit a board with deatiled specification and details of work as directed by the Engineer-In-Charge for which no Extra Payment shall be made.

2. The labour crss will be deducted as per prevaling Rules i.e 1% of the work done.

3. GST and Income tax TDS will be deducted at a Source while making Payments of bills.

4. In all RCC items in Rate Analysis Standard cement Consuption has been taken as per Govt.G.R: PRC -10/2017 cement consumption/16/c, Date: 11/05/2017 as stated i. S.O.R

therefore in RCC Items where there is a changed as per actual mix design the cost of diffrence of cement consumption have been deduvted from the rate of orignal item at the rate of

input rate mentioned in all the tender.

Above all items of " Schedule-B" with iem Description,Unit,Rate & Amount Have verified by me and found Order.

Deputy Executive Engineer Executive Engineer

R P Sub Division R & B (Pan) Division

Gandhinagar Gandhinagar