REDRESSAL OF DAY TO DAY COMP LAINTS, DESLUDIGING, CLEANING AND REPAIR OF SEWAGE LINE,SOAKAGE WELL, SEPTIC TANK,REAPIAR TO INTERNAL WATER SUPPLY ,PLUMBING WORK,CLEANING OF WATER TANK AND OTHER MAINTAINANCE WORK AT NAUGAM UNDER GE 969 EWS BARAMULLA

Amount

Taking down chowkhat or frame without taking of shutter of any description n.exc 1.50 Sqm each complete all as specified and directed by engineer-in-charge.

Taking down chowkhat or frame without taking of shutter of any description but exc 1.50 sqm but n.exc. 4.00 sqm each. complete all as specified and directed by engineer-in-charge.

Taking down shutter of any description n exc 1 Sqm each complete all as specified and directed by engineer-in-charge

Taking down shutter of any description exc 1 Sqm but n exc 2.00 Sqm each complete all as specified and directed by engineer-in-charge

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 and finished smooth and even without using extra cement including taking down old plaster complete all as specified and directed by engineer-in-charge

M&L rendering 15mm thick in CM 1:4 on stone masonary surfaces or surfaces other than fair faces of brickwork and finishing fair & smooth without using extra cement including taking down old plaster complete all as specified and directed by engineer-in-charge.

All as per item No 06 above but on brick or concrete surfaces complete all as specified and directed by engineer-in-charge

M & L for 50mm thick PCC 1:3:6 type C-2 using 40 mm graded agg as in plinth protection finished even and smooth Including demolition complete all as specified and directed by engineer-in-charge.

M&L PCC 1:2:4, type B-1 (using 20mm graded crushed stone aggregate) as in coping incl necessary formwork, weathering, slightly rounded or chamfered angles including demoltion complete all as specified and directed by engineer-in-charge

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangle) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified including 15mm thick screed bed in CM 1:6 and dismantling old floor hearth or wall tile complete all as specified and directed by engineer-in-charge

M&L for non-skid coloured ceramic tile 7 to 8mm thick (Square/rectangular/in joint less) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over 15 mm thick screed bed in CM (1:6) including demolition of stone slabe slabs & tiles of any description or thickness in any position complete all as specified and directed by engineer-in-charge

M&L Coloured glazed ceramic tiles in vertical surface 450x 300x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including 10mm thick mortar bed in CM 1:4 and dismantling old floor hearth or wall tile as specified & directed by Engr-in-Charge.

M&L vitrified coloured ceramic tiles 10mm thick (square/rectangular) polished area of each tiles exceeding 0.42 Sqm but n .exc 1.0 Sqm in floors etc set and jointed in neat cement slurry and pointed in whited or coloured cememtn to match dark shade tiles. all as specified including 15mm thick screed bed in CM 1:4 and dismantling old floor hearth or wall tile as specified & directed by Engr-in-Charge

S&F in repair pre-painted galvalume aluminium zinc coataing GI based profile steel sheet 0.50 mm thick of any colour having tnsile strength of 550 MPA as in roof covering/cladding to wall,fixed with self tappping screw as specified incl including dismantling old sheetcomplete all as specified and directed by engineer-in-charge

S&F in repair 0.80 mm thick plain galvanised, mild steel sheeting , in ridges, hips valley gutters drip and straight flashing etc with grade of zinc coating 275 including dismantling old sheet complete all as specified and directed by engineer-in-charge

S&F in repair PVC hollow interlocking wall/ceiling paneling of 5mm thick prelaminated PVC sheet, panel & strips shall be of 600 kg / cum density manufactured by an ISO-9000 certified company. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement. Note: Colour and Pattern shall be approved by GE and contractor shall not have any claim whatsoever on this account.

S&F in repair Venetion blind coloured strip 75 mm top 5 mm thick powder coated aluminium rod ends at brackets are moulded type with all arrangements ccomplete all as specified and directed by engineer-in-charge

S&F in repair Wooden wall panelling with tongued & grooved joint laminated over high quality DHF,8 mm to 10 mm thick fixed to timber frame workcomplete all as specified and directed by engineer-in-charge. Note :-Timber frame work rate included in same item.

S&F 2nd class Hard wood plain soild,straight chowkats and frame wrought,framed rebated on soild,rounded or chamfered,put together with pinned at joints complete all as specified and directed by engineer-in-charge

S&F 35 mm thick 2nd class softwood plain,framed,pannelled shutters(any number of pannel),with pannel of timber flat on both sides (feather edged),or of veneered particle board medium density wood particle board with commercial face vennered supplied and fitted to chowkats, complete all as specified and directed by engineer-in-charge

S&F 35mm thick 2nd class soft wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted without and mitred beads for securing glass or gauge etc all as specified in SSR Pt 1sec-8.24(a)complete all as specified and directed by engineer-in-charge

S&F 30mm thick 2nd class soft wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted without and mitred beads for securing glass or gauge etc all as specified in SSR Pt 1sec-8.24(a) complete all as specified and directed by engineer-in-charge

S&F, butt hinges, medium weight ,cold rolled mild steel 100mm complete all as specified and directed by engineer-in-charge

All as item No 23 above but 75 mm long complete all as specified and directed by engineer-in-charge

S&F Galvanised mild steel wire cloth 0.56 nominal dia of wire and width of aperture 1.18mm complete all as specified and directed by engineer-in-charge

M & L sheet glass ordinary quality 3.00 mm thick and glazing with oil putty in square n exc 0.50 sqm in each panes fixed to steel or wooden window framescomplete all as specified and directed by engineer-in-charge

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads and S&F sheet glass ordinary quality 3.00 mm thick and glazing with oil putty in square n exc 0.50 sqm in each panes fixed to steel or wooden window frames complete all as specified and directed by engineer-in-charge

S&F in repairs steel tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors of 15mm bore complete all as specified and directed by engineer-in-charge

Taking down and cleaning for refixing steel tubes medium grade galvanised with all fitting and fixed to wall or laid in trenches 20 mm bore including complete all as specified and directed by engineer-in-charge

S&F in repairs steel tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors of 20mm bore complete all as specified and directed by engineer-in-charge

Taking down and cleaning for refixing steel tubes medium grade galvanised with all fitting and fixed to wall or laid in trenches 15 mm bore including taking down and cleaning for refixing complete all as specified and directed by engineer-in-charge

S&F in repairs 500 ltr Rotational moulded polyethylene water storage tanks (cylindrical) vertical with closed top ) hoisted and fixed in poisition all as specified in SSR Part I complete all as specified and directed by engineer-in-charge

S&F in repairs 1000 ltr Rotational moulded polyethylene water storage tanks (cylindrical) vertical with closed top ) hoisted and fixed in poisition all as specified in SSR Part I complete all as specified and directed by engineer-in-charge

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position 500 Ltr to1000 Ltr capacity complete all as specified and directed by engineer-in-charge

S&F bib tap of CP fancy type with butterfly handle screwed down screwed for iron pipe of 15mm bore fixed in repairs complete all as specified and directed by engineer-in-charge

S&F in repair for 15 mm bore Bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed by engineer-in-charge

S&F in repair Bib tap (CP) 15mm with wall flange complete all as specified and directed by engineer-in-charge

S&F in repair angle/stop cock (CP) with wall flange all complete all as specified and directed by engineer-in-charge

S&F in repair Brass CP Mixer 15 mm dai for mixing Hot and Cold water screwed down for iron pipe and fixed complete all as specified and directed by engineer-in-charge

S&F Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) complete all as specified and directed by engineer-in-charge

S&F Union of pipes in repair of 20 mm dia One end screwed to iron pipe, etc.complete all as specified and directed by engineer-in-charge

S&F Pillar tap cast copper ally with capstan heads, chromium plated screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe pipe and fixed with 15mm bore in repairs complete all as specified and directed by engineer-in-charge

S&F in repair Ball brass valves high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule fixed in repairs 15mm dia complete all as specified and directed by engineer-in-charge

S&F in repair Ball brass valves high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule fixed in repairs 20mm dia complete all as specified and directed by engineer-in-charge

S&F in repair for 15 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixedand fixed complete all as specified and directed by engineer-in-charge

S&F in repair for 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixedand fixed completed all as specified.

M&L Lagging to pipes used in internal water supply or plumbing all round with, 25mm min thick bonded mineral wool preformed ‘SNAP ON’ pipe sections of density 144 Kg/cum conforming to IS 9842 provided with chicken mesh wire netting 25 gauge, 20mm dia complete all as specified and directed by engineer-in-charge

S&F Waste fittings 32 mm dia, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed in repair complete all as specified and directed by engineer-in-charge.

S&F Waste fittings 40 mm dia, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed in repair complete all as specified and directed by engineer-in-charge

S&F angle valves CP screwed down high pressure of fancy type chromium plated screwed both ends for iron pipe or for union and fixed with 15mm bore in repairs complete all as specified and directed by engineer-in-charge

S&F PVC connection 15mm size with PTMT nuts of length 450 in repairs complete all as specified and directed by engineer-in-charge

S&F PVC connection 15mm size with PTMT nuts of length 600 in repairs complete all as specified and directed by engineer-in-charge

S&F Vitreous China squatting pan,Orissa Pattern size 580x440 mm white with integral foot rests exccludidng flushing cistern flush pipe including connection to trap,anti syphonate pipe etc. complete,fixed in repairs all complete all as specified and directed by engineer-in-charge

S&F in repair vitreous china wash down water closet (pedestal pattern) white (excluding fixing bolts flushing cister and slush pipe) with seat cover with CP screw complete all as specified and directed by engineer-in-charge

S&F Vitreous chinaware wash hand basin white flat back size 550x400mm size including brackets and PVC pipe check nut complete fixing accessories incl taking out existing complete all as specified and directed by engineer-in-charge

Supply only PVC valveless, syphonic action type flushing cistern, 10 litres capacity, plunger type, low level, white with inlet, ball valve, float and handle, 32 mm dia PVC long bend flush pipe 90cm long including PVC connection 15mm dia 450mm long with brass CP nuts and washers at both ends, complete all as specified and directed by engineer-in-charge

S&F in repair Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed by engineer-in-charge

S&F in repair grating doom type 100 mm dia of PTMT incl fixing with white cement and making good complete all as specified and directed by engineer-in-charge

S&F PVC floor traps plain with gratings incl jointing to waste pipe with solvent cement dia of out let 75mm complete all as specified and directed by engineer-in-charge

S&F in repair PVC (SWR) 75mm bore pipes single socketed in any length with rubber ring joints and fixed to wall and laid in floor trenches complete all as specified and directed by engineer-in-charge

S&F in repair PVC (SWR) 110mm bore pipes single socketed in any length with rubber ring joints and fixed to wall and laid in floor trenches complete all as specified and directed by engineer-in-charge

S&F PVC (SWR) bends/Tee 75mm dia fixing complete all as specified and directed by engineer-in-charge

S&F PVC (SWR) bends/Tee 110mm dia complete all as specified and directed by engineer-in-charge

S&F in repair PVC (SWR) 150mm bore pipes single socketed in any length with rubber ring joints and fixed to wall and laid in floor trenches complete all as specified and directed by engineer-in-charge

S&F aluminium alloy powder coated aluminium door frame fixed with side hung shutters and glazing fixed with and including 5.50mm thick tinted glass fixed with rubber gasket with aluminium heading, clips frame made with aluminium box sec as appended below complete all as specified and directed (a) Frame 100x44x1.48mm thick with rawl plug (b) Middle and lock rail : 150x44x1.48mm thick (c) Bottom rail : 150x44x1.48mm thick (d) Top rail/style : 85x44x1.48mm thick (e) Aluminium beading : 0.7mm thick (f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver aluminium stopper, cleat double action floor spring hydraulically regulated made of n.less than 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other part of steel heavy duty ( Make Sandhu ISI marked or its equivalent approved make) (g) Making good of wall surface to match with existing surface complete.

S&F Powder coated aluminium sliding windows frame with movable shutter ( sliding on minimum two PVC roller of best quality, for each shutter on three tracks with stainless steel mosquito proofing and glazing shutter and incl 5.50 mm thick glass & stainless steel wire messs fixed with neoprene rubber gasket with aluminium beading, clips,frame made with aluminium section as appended below- (i) Window frame :63x35mm X 1.48 mm thick for two tracks. (ii) Top/bottom rail and style / rail of shutter : 19x38x1.48mm thick and over. (iii) Aluminium beading - 0.7mm thick (iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperature 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete. (v) Aluminium fittings such aluminium suitable handle with auto interlocking closing (vi) Making good of wall surfaces to match with existing surfaces complete all as specified and directed.

S&F partition wall of powder coated aluminium hollow sections members of size 63.50 mm x38mmx 1.48 mm thick with distance of vertical hollow section, 1.2mtr to 1.8 mtr height of wall having top rails ,bottom rails and middle rail of size 63.50 mm x38mm x 1.48 mm and upto middle rail wall panels shall be covered by 5 mm thick aluminium composite panel LDPE core PET coating ( both side decorative type )with aluminium clip height of middle rail shall be 1 meter from floor and remaining portion above middle rail shall be provided with 5 mm thick glass incl eaching approved designed with aluminium stiprs/beadings with rubber gasket as per existing or as provided complete all as specified and directed by engineer-in-charge

S&F 5.50mm thick sheet glass ordinary quality and glazing with oil putty or with wooden beads n.exc 0.5 sqm in each pane) complete all as specified and directed by engineer-in-charge

M&L Aluminium anodised barrel tower bolts of extruded section and fixed of 200mm length complete all as specified and directed by engineer-in-charge

All as per item 70 above but 100 mm size complete all as specified and directed by engineer-in-charge

S&F Aluminium alloy,anodised, sliding door bolts plate type stove enameled black with bright bolts not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple. Plate 250mm long all as spd & directed.

S&F butt hinges medium weight cold rolled Aluminium anodised100mm complete all as specified and directed by engineer-in-charge

S&F aluminium handle cast type adonised 150mm complete all as specified and directed by engineer-in-charge

S&F Aluminium anodised door closer fixed in repairs complete all as specified and directed by engineer-in-charge

M&L Preparing newly plastered surfaces of walls and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed by engineer-in-charge

M&L Applying two coat of cement base paint on plastered or unplastered surfaces incl preparation of surfaces complete all as specified and directed by engineer-in-charge

Preparation of new wooden surface, not otherwise described over 10cm width or grith applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed by engineer-in-charge

Preparation of old painted surfaces of any descriptoin, not otherwise described, over 10cm witdth or girth and applying one coat of synthetic enamel paint on wooden surfaces complete all as specified and directed by engineer-in-charge

Preparation of old painted surfaces of any descriptoin, not otherwise described, over 10cm witdth or girth and applying one coat of synthetic enamel paint on steel and iron surfaces complete all as specified and directed by engineer-in-charge

S&F sheet glass shelf assembly consisting of 5.5 mm sheet glass shelf 12 cm wide with brass chromium plated bracket guard and 60 cm long complete all as specified and directed by engineer-in-charge.

S&F Corner glass shelf assembly consisting of 5.5mm thick sheet glass with chromium plated bracket guard complete all as specified and directed by engineer-in-charge

S&F CP health flucet hand held triggered nozzle and delivers a spray of water with pipe complete all as specified and directed by engineer-in-charge

S&F CP jet spray with flexible tube 1.5 mtr long complete all as specified and directed by engineer-in-charge

S&F in repair 2 Way bib cock (CP) /Angle Cock (CP) with wall flange complete all as specified and directed by engineer-in-charge

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fitted in openings as per specification and drawing shown in SSR Part-II, complete all as specified and directed by engineer-in-charge

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement from stiles and plained colour PVC sheet to be fitted with MS frame welded/sealed to the styles & rails with suitable PVC sheet beading, and jointing together with solvent cement, supplied & fitted in the frame at site as per specification & drawings shown in SSR Part-II, complete all as specified and directed by engineer-in-charge

S&F Aliminium anodised barrel tower bolts, 150 mm long complete all as specified and directed by engineer-in-charge

S&F Aluminium anodised handles, cast type anodised 125 mm long complete all as specified and directed by engineer-in-charge

S&F MS decorative curtain rod 20 mm dia covered with coloured PVC layer with decorative ends incl PVC Knobs and MS Bracket both ends complete all as specified and directed by engineer-in-charge

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) and boarding any thickness, including cover fillets complete all as specified and directed by engineer-in-charge

M&L for 4 mm thick veneered decorative Ply wood, grade 1 (with BWR resin) with decorative face veneers on one face has decorative veneer fixed with screws to timber frame work on ceiling etc. Note: Colour and Pattern shall be approved by GE and contractor shall not have any claim whatsoever on this account.

M&L for 4 mm thick veneered decorative Ply wood, grade 1 (with BWR resin) with decorative face veneers on one face has decorative veneer fixed with screws to timber frame work in partition, wall panelling etc. Note: Colour and shade shall be approved by GE and contractor shall not have any claim whatsoever on this account.

S & F Second class soft wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 6 and not exceeding 13 Sq. cm complete all as specified and directed by engineer-in-charge

S&F second class soft wood plain fillets square, rectangular or triangular in section, wrought secured with nails, cross sectional area not exceeding 3 Sq. cm complete all as specified and directed by engineer-in-charge

M&L 2nd class soft wood (kail) Prelaminated wooden flooring as in boarding in floors incl 5mm thick foam, 15mm thick, planed one side and edges tongued and grooved or rebeated as in flooring fixed with nails in floor, complete all as specified and directed by engineer-in-charge Note: Colour and shade shall be approved by GE and contractor shall not have any claim whatsoever on this account.

M&L for PCC (1:3:6) type C2 (using 40 mm graded stone aggregate) in foundations filling and mass concrete including demolition complete all as specified and directed by engineer-in-charge

M&L for PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in as in mass concrete including demolition old PCC complete all as specified and directed by engineer-in-charge

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 including dismantling old wall complete all as specified and directed by engineer-in-charge

M&L for brick work with sub class 'B' bricks (Old size) straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6 including dismantling old brick work complete all as specified and directed by engineer-in-charge

Extra for forming fair finished drain or channel exceeding 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends complete all as specified and directed by engineer-in-charge

M&L for pre-cast RCC (1:1.5:3) type B1 (using 20 mm graded stone aggregate) set in CM (1:4) as in drain/Culvert/Manhole covers including all necessary form works complete surface finished properly using extra cement and demolition of reinforced cement concrete (re-inforcement cut as required to facilitate demolition) complete all as specified and directed by engineer-in-charge

M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for drain covers/Culverts including binding wire complete all as specified and directed by engineer-in-charge

All as per item No 103 above but 6 to 8mm dia complete all as specified and directed by engineer-in-charge

Demolition and breaking up 75/110 mm dia drain pipe (AC,saltglazed, PVC or RCC pipes ) set in CM or any description incl Excn of Earthwork , RFR, removal and making good complete complete all as specified and directed by engineer-in-charge

M&L for rendering 10 mm thick in CM 1:3 internally to manholes on concrete block or concrete surfacesand finished even and smooth using extra cement complete all as specified and directed by engineer-in-charge

M&L for PCC (1:4:8) type D2 using 40mm graded stone aggregates as in bed to drain pipes including packing under and haunching against the sides of pipes after these are laid tested for 100 mm bore of pipes complete all as specified and directed by engineer-in-charge

Taking out (desilting) silt brick bats, debries, liquid waste sludge in solid/semi solid state from manholes/soakage well including pumping out sludge wherever necessary, plugging diverting the flow in the drain, if necessary and stacking the removed silts in depots away from the edge of manholes as directed including use of safety belts and taking similar precautionary measures and removing the sludge etc. to a distance exc 250 mtr. but n.exc 500m & levelling the manhole cleaned and flushed with water etc. all as specified/directed manholes upto the depth of 1.00 mtr complete all as specified and directed by engineer-in-charge

All as per item No. 108 above but manholes/Soakage well depth exc 1.00 mtr and n.exc 2.50 mtr complete all as specified and directed by engineer-in-charge

Desludging of septic tanks and manholes any capacity , size and depth including disposal of waste water and sludge through Using honey sucker machine and dividely store in covered container etc complete and removing the sludge in covered van/trolly out side the deffence land and taking off the manhole cover and placing in the same position after taking out sludge and covering pit with minimum 30 cm thick layer of earth work etc complete all as directed NOTES :- The unit rate for desludging using Honey sucker Machine including hiring rate from any sources, Its operator, Hose required(at least 50 mtr) and Fuel etc. Per Trip of Truck shall deemed to include full capacity of Tank of the Truck i.e 3.0 to 4.0 Cum and the cost of dewatering shall also be included in the unit rate. Delivery point of desludging out side of Defence land at any distance also included in the rates. Contractor has to excavate 2 mtr dia and at 3.o mtr depth desluding well whereever shown by Engr-in- Chrage for delivery point of desluding in side of Defence Land at any distance as required also included in the rates. Contractor concern will liaise with the sources of Honey Sucker Machine and during working any defects raised contractor will be responsible in all respect

M&L cleaning/function of existing sewage system and pumping station (comprising of sewage lines in SGSW pipes, hume pipe and CI pipes) of any dia at any depth, manholes septic tanks and soakage wells of different types of sizes any in any position i.e. below or above ground level, located in different situations and also on the surfaces of the wall etc complete in perfect function/running/flowing condition without any obstruction by removing all blockage in system and including removing of all wastes solid or liquid of any description (cleaning /removing blockage of water cosets, urinals, wash hand basin, sinks, kitchen & bathroom floor/nahani trap and gully trap etc including cleaning of drain pipes of any description & size (rate includes for removing off MH covers & placing the same in position after cleaning by rodding/choke remover or by any other suitable means manually as in foul condition in the entire area of works under AGE B/R-I. Complete all as specified and as directed. NOTE:- (i) Employing daily one sweeper with one helper (safai wala) who report everyday and they will cater to the sewage complaints fo the entire sub division as per above items including convenyance of workers as per work order/complaint slip.(ii) The above mentioned individuals to look after the sewage complaints of the entire locations as directed by concerned executives and shall report daily reporting the sub division office.(iii)Conractor shall be entirely responsible for the accident/risk insurance poicy of the each worker who are empoying in sewage cleaning worker (iv) All Sewage blockage complaints must be attended immediately on receipt but not later than 24 hours. (v) Recovery (Penalty) for not attending complaint beyond 24 hours shall be Rs. 100.00 per complaint per day delayed.

Taking out silt, liquid water sludge in solid/semi solid state from septic tank/sump of any capacity,depth and size Manually and removing the same to a distance of exc 250 m but n exc 500 m including depositing the sludge ,excavation in anytype of soil with covering by earth over it and leaving the septic tank/sump clean etc. M&L cleaning/function of existing sewage system and pumping station (comprising of sewage lines in SGSW pipes, hume pipe and CI pipes) of any dia at any depth, manholes septic tanks and soakage wells of different types of sizes any in any position i.e. below or above ground level, located in different situations and also on the surfaces of the wall etc complete in perfect function/running/flowing condition without any obstruction by removing all blockage in system and including removing of all wastes solid or liquid of any description (cleaning /removing blockage of water cosets, urinals, wash hand basin, sinks, kitchen & bathroom floor/nahani trap and gully trap etc including cleaning of drain pipes of any description & size (rate includes for removing off MH covers & placing the same in position after cleaning by rodding/choke remover or by any other suitable means manually as in foul condition in the entire area of works under AGE B/R-I. Complete all as specified and as directed. NOTE:- (i) Employing daily one sweeper with one helper (safai wala) who report everyday and they will cater to the sewage complaints fo the entire sub division as per above items including convenyance of workers as per work order/complaint slip.(ii) The above mentioned individuals to look after the sewage complaints of the entire locations as directed by concerned executives and shall report daily reporting the sub division office. (iii) The contractor shall be entirely responsible for the accident/risk insurance poicy of the each worker who are empoying in sewage cleaning worker (iv) All Sewage blockage complaints must be attended immediately on receipt but not later than 24 hours. (v) Recovery (Penalty) for not attending complaint beyond 24 hours shall be Rs. 100.00 per complaint per day delayed.

M/S HAJI MOHD ASHRAF SUMJI