CONSTRUCTION OF PROJECT-D INFRASTRUCTURE AT NAVAL DOCK YARD VISAKHAPATNAM

Amount

Schedule "A" Part – I to Schedule "A" Part – XV: NOTE: Schedule "A" Part – I to Part – XV are prepriced by DGNP(V). Bidders shall insert their Lumpsum amount in Green coloured field under Column - 6 only

Lumpsum price worked out by the contractor for "BUILDINGS & STRUCTURES", as listed in Schedule "A" Part – I

Lumpsum price worked out by the contractor for "DEMOLITION/ DISMANTLING", as listed in Schedule "A" Part – II

Lumpsum price worked out by the contractor for "CLEARANCE / AREA DEVELOPMENT / EARTH WORK EXCAVATION", as listed in Schedule "A" Part – III

Lumpsum price worked out by the contractor for "PILE FOUNDATION", as listed in Schedule "A" Part – IV

Lumpsum price worked out by the contractor for "INTERNAL WATER SUPPLY", as listed in Schedule "A" Part – V

Lumpsum price worked out by the contractor for "INTERNAL ELECTRIFICATION", as listed in Schedule "A" Part – VI

Lumpsum price worked out by the contractor for "EXTERNAL WATER SUPPLY", as listed in Schedule "A" Part – VII

Lumpsum price worked out by the contractor for "EXTERNAL ELECTRIFICATION", as listed in Schedule "A" Part – VIII

Lumpsum price worked out by the contractor for "PATH/ HARDSTANDING", as listed in Schedule "A" Part – IX

Lumpsum price worked out by the contractor for "AREA DRAINAGE", as listed in Schedule "A" Part – X

Lumpsum price worked out by the contractor for "SEWAGE DISPOSAL", as listed in Schedule "A" Part – XI

Lumpsum price worked out by the contractor for "FIRE FIGHTING SYSTEM", as listed in Schedule "A" Part – XII

Lumpsum price worked out by the contractor for "LIGHTNING PROTECTION", as listed in Schedule "A" Part – XIII

Lumpsum price worked out by the contractor for "AIR CONDITIONING", as listed in Schedule "A" Part – XIV

Lumpsum price worked out by the contractor for "DIVERSION OF EXISTING PIPELINE/ CABLE", as listed in Schedule "A" Part – XV

SCHEDULE "A" PART - XVI [MISCELLANEOUS ITEMS]

M&L for Reinforced Ready Mixed Cement Concrete M–40 Design Mix with admixture Conplast SP-435 A2 or Auramix 400 or equivalent, as in Piles, including necessary dewatering, formwork, concrete mixed in RMC plant, transporting, placing, compacting, vibrating etc., complete all as specified and as directed by Engineer-in-Charge. Notes: (i) Design mix shall be as per IS-456-2000, max size of aggregate shall not exceed 20mm and the slump shall be 150 to 180mm. (ii) Reinforcement shall be measured and paid separately. (iii) Unit rate shall be deemed to include interalia for preliminary design mix, works test cubes as specified. (iv) Minimum cement content shall be 400 Kg/ Cu.m. of concrete for M40 (Piles) using PSC with minimum slag content of 50% (fifty percent) (v) Admixture shall be added as per manufacturer instructions. The rate for Admixture shall be deemed to be included in the quoted rate. (vi) The unit rate shall be deemed to include for carrying out non-destructive integrity test for 100% of the total number of piles as per IS 14893-2001 shall be done by Govt Engineering College / NIT/IIT in the presence of contractor and the test results shall be vetted by the same authorities. Cost of testing is included in the quoted rates.

(vii) In case at the time of mix design cement content is increased beyond minimum content given above, no extra payment will be made, if cement content is decreased beyond minimum content, necessary minimum DO shall be initiated. (viii) Standard manufactured cover blocks as per IS should be used, Site cast cover blocks shall not be used. (ix) Pile shall be casted as mentioned in drawings. However, for payment purpose the length of pile shall be measured up to cut off level only. The unit rate/Lumpsum price quoted shall be deemed to include this aspect. (x) Core sample testing shall be carried out as directed GE upto 5% of piles.

M&L for Drilling or boring for 800mm nominal dia. bored cast-in-situ piles through any or all types of strata i.e soft/loose soil, stiff clay, gravel, cobble stone, compact moorum, soft conglomerate or loose boulders, disintegrated rock, weathered rocks/rocks etc., (except hard rock for socketing depth) upto top of socketing depth/founding depth by adopting suitable method with perennial water and disposal of drilling/bored materials outside MD land as directed, ccomplete all as specified and as directed by Engineer-in-Charge.

All as per Serial Item No. 17 here in before but for 800mm nominal dia through hard rock for founding depth minimum 2D (Where D is dia of pile), complete. Notes for Item Nos. 17 & 18:- (i) The depth of boring for piles shall be measured from existing ground level to the approved founding level. (ii) It shall be ensured that the waste bentonite slurry/ drilled or bored material is pumped off from the premises to locations shown by GE to contractor at his own cost. (iii) All channels/tanks made for bentonite circulations shall be filled with approved moorum obtained by contractor at his cost after clearing all bentonite cakes. (iv) The contractor may use any approved method as approved by GE for boring without any extra cost to the Govt. The rates for boring of piles shall be inclusive of any method/ casing that may be used by the contractor for bored piles. Nothing extra shall be paid. (v) For the purpose of payment of boring/drilling, description of hard rock shall be as given in SSR Part-I specification. (vi) The rate quoted by the contractor shall be inclusive of the rates for the shifting and setting up of piling rig as many times as required.

Carrying out initial load tests on test pile of 800mm dia as per standard procedure laid down in IS-2911 by static load test method with compressive strength, including construction of test cap, dismantling the cap after the test and clearing the site and maintaining complete records of load settlements etc. as specified and as directed by GE and submission of reports for test load of 775 Ton in non-working areas in the vicinity of site, including the cost of new piles with specification as same as working pile with minimum depth of socketing into the hard rock 2D (Where D is dia of pile) depth, complete all as specified and as directed by Engineer-in-Charge. Note: Load rquired for testing as per IS shall be arranged by the contractor and test pile shall be abondoned after testing.

Carrying out routine load test on 800mm dia pile (working pile) as per standard procedure given in IS-2911 (Part IV) by static load test method with compressive strength, including construction of test cap, dismantling the cap after the test and clearing the site and maintaining complete records of load settlements etc. and submission of reports for test load of 465 Ton, complete all as specified and as directed by Engineer-in-Charge.

Removing demolished building materials etc. to a distance of 8 to 10km including loading , unloading and stacking at the destination, complete all as specified and directed.

M&L for Point wiring with 1.5 Sq.mm (nominal cross sectional area) FRLSH PVC insulated unsheathed copper conductor cable, single core multi stranded 1100Volt grade confirming to IS 694: 1977, drawn in and including rigid PVC conduit not less than 20mm bore, concealed type, medium grade as per IS 9537 (Part 1-1983) with conduit accessories, junction boxes, tees, terminal boxes with and including factory made MS boxes, modular cover plates with frame for mounting modular switches, including one run of 1.5 Sq.mm single core FRLS PVC unsheathed copper conductor cable as earth continuity conductor and connected to common earth dolly, for one light/ bell/ fan/ exhaust fan/ wall mounted fan/ socket controlled by one 1-way switch, complete all as specified and as directed by Engineer-in-Charge. Note: Cutting chases and making good surfaces shall be included in the unit rate.

Description all as per Serial Item No. 22 here-in-before but with 1.5Sqmm copper conductor cable and 1.5Sqmm cable as earth continuity conductor for one light point controlled by two way switch, complete all as specified and as directed by Engineer-in-Charge.

Description all as per Serial Item No. 22 here-in-before but with 2.5Sqmm copper conductor cable and 2.5Sqmm cable as earth continuity conductor for 6/16 Amp switch socket point controlled by one way switch on independent board complete all as specified and as directed by Engineer-in-Charge.

S & F Air Circulator fan 600mm sweep with necessary clamps, nuts & bolts etc including flexible cable suitable for 230 Volt, AC 50 Hz with inbuilt regulators complete all as specified and as directed by Engineer-in-Charge.

S & F of Energy Saving, environment friendly high bay LED light luminaries of 120 Watt, 230V, 50 Hz including fittings and hanging arrangement/ fixing arrangement for fixing of light fitting as indicated by channels, clamps, nuts & bolts etc complete all as specified and as directed by Engineer-in-Charge.

S & F 2 X 2 ceiling lights of 36 watts ultra modern recess mounting luminaire with high performance LEDs, suitable for mounting complete with all accessories internally pre wired and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of MCB's VTPN DB, 4 ways, 125 Amps, double door suitable for MCCB incomer complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of MCB's DB, TPN 4 ways, 63 Amps, double door suitable for MCCB incomer complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of MCB's DB, SPN 8 ways, double door complete all as specified and as directed by Engineer-in-Charge.

Supply and fix MCB SP 6-32A, 10KA with necessary connecting up in MCB DB complete all as specified and as directed by Engineer-in-Charge.

Supply and fix MCB SPN 32A, 10KA with necessary connecting up in MCB DB complete all as specified and as directed by Engineer-in-Charge.

Supply and fix MCCB TPN 63A, 25KA with necessary connecting up in MCB DB complete all as specified and as directed by Engr-in-Charge.

M&L for Earthing complete with galvanised steel earth plate electrode 60cm X 60cm X 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead 4mm GI wire by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 of SSR Part-I, including excavation / earth work in any strata, adequate quantity of charcoal and common salt, PCC chamber with RCC 1:2:4 type B1 40mm thick cover slab with 8mm dia TMT bars @150mm c/c in both ways, suitable handle and angle iron frame of suitable size to fix the cover, with 20mm bore GI pipe light grade for watering with funnel, wire mesh and 15mm bore GI pipe medium grade for GI wire protection and 4mm GI earth wire, including testing after completion, complete all as specified and as directed by Engineer-in-Charge. Note: Earth wire will be measured after 7.5mtr from the earth strip or earth testing terminal block whichever is lesser under relevant item.

M&L for Valve chamber of size 1000mm x 1000mm x 600mm internal dimensions, with and including excavation in any type of soil, spreading, levelling and refilling etc. PCC (1:4:8) type D2 for foundation, Fly ash brick work of one brick thick wall in CM (1:4) including internal plaster 15mm thick in CM (1:4) external plaster 15mm thick(1:4) upto 150mm below GL and providing coping in PCC (1;2:4) type B1, angular iron frame of size 50x50x6mm with 6mm thick MS plate cover complete including locking arrangements and having FRP coating of 2mm thick on both inside and outside surfaces all as shown in TD drawing and complete all as specified and as directed by Engineer-in-Charge.

Supply, install, testing and commissioning compact sub-station complete with following items:- A) HT SWITCHGEAR 11kV, 630Amps 21KA for 3 Sec. SF6 insulated Non-walk in type Compact switchgear (Type CCV) consisting of Two No's fixed Manual load break switches (LBS) and one No. Fixed Manual Vacuum Circuit Breaker(VCB) having inbuilt load break switch and earth switch within SF6 insulated robotically welded non ferrite non magnetic stainless steel enclosure of thickness 2.5mm having IP 67, with series trip,self powered microprocessor based numerical 3 O/C & 1 E/F relay (IDMTL + Inst.) protection. Interconnection between HT switchgear and transformer shall be using 1Cx3x95 sq.mm Al. unarmored XLPE Cable, 11KV grade . Relay shall be self powered of Ashida/C&S Make. (50,50N,51,51N) with RS485 communication port-01 Protection CT shall be 40/1A 2.5VA 5P10-1 set Standard Manometer (SF6 Gas Pressure Indicator)-01 No. Fault Passage Indicator (FPI) for incoming LBS only-01 No. Voltage presence indicator (VPIS) for incoming Healthy Indications-01 set. Manual push button for breaker ON/OFF-01 set Mechanical Indication for Breaker & LBS ON/OFF/EARTHED-03 Nos. Operating handle-01 No. All incoming modules of the RMU shall be capable for cable termination of 3C x 300 sq.mm Al XLPE Cable, incoming cable termination kits shall be in the scope of purchaser only.

Item No. 36 (Contd……) B) TRANSFORMER 315 KVA 11KV/433V Dyn11 Copper Wound Cast Resin Dry Type (AN) distribution Transformer with Off Circuit Tap Links (Make: The make of the dry type transformer shall be the approved vendor of compact substation manufacturer.)-01 No Off Circuit Tap Links (OCTL), Tapping range +10% to -10% in a steps of 2.5% (4 Steps/5 Positions) Insulation Class: F Temp. Rise Shall be 90 Deg. C Over an ambient of 50 Deg.0 Temp. Transformer Losses: As per iS 2026 & 1511171 No Load Losses : 1000 W (+IS Tol.) Load Losses at 75 Deg.0 : 4000 W (+IS Tol.) % Impedance (%Z) shall be 4.5% (Subject to IS Tol.) Rating & Diagram (R&D) Plate (Fitted on Transformer)-01 No Surge Arrestor (Fitted on Transformer CCA on HV Side)-01 No Digital Winding Temp. Indicator with Alarm and Trip Contacts (With RS-485 Port)-01 No Rated tempreture class of trasnformer compartment shall be K-10 type test report to be submitted. C) LT PANEL- 630 A Aluminium Busbar (100% for Phase & 100% for Neutrals) Current density lamp/sqmm, having IP2X, Fabrication using 1.5/2mm CRCA sheet steel complete with Internal wiring consisting of following.

Item No. 36 (Contd……) INCOMER From transformer 630Amps 4P 50Hz 36KA Fixed Manual Type Moulded Case Circuit Breaker (MCCB) with microprocessor based release for Overload (0/L), Short circuit (S/C) & Earth Fault (E/F) protection. (Make: ABB) -01 No LED type Indicating Lamp - RYB, ON-OFF-TRIP -01 set LT side metering CT 630A/ 5A, 5VA, Cl:1.0 (G&M/ NEWTEK/ Eq) -01 set Digital Multifunction Meter (MFM), CL-1.0 Accuracy with RS485 Port -01 No APFC Panel 32A 433V 3P 50Hz 36 KA Fixed Manual MCCB Thermal Magnetic (TMD) based released OC, SC Protection (For Capacitor Bank Incomer)-01 No 20kVA Capacitor bank ( 5x4)-01 No TAS-Powertek make APFC Relay for 4 steps-01 No 5 KVAR metallized polypropylene capacitor bank -01 No Capacitor duty contactor for switching on & switching off 5 KVAR bank -01 No 16Amps 433V 3P 10KA Miniature Circuit Breaker for 25kVAR capacitor protection -01 No

Item No. 36 (Contd……) D) OUTDOOR ENCLOSURE Outdoor type enclosure having construction of Galvanised Sheet Steel having 1.5mm thickness for Non-load bearing & 2 mm for Load bearing partition sheets & Door with HRCA 4 mm base frame. The Enclosure shall have IP54 degree of protection for HT & LT switchgear compartment & IP34 degree of protection for Transformer compartment. The enclosure exterior shall be Powder Coated (RAL 7032 ). Each compartment will be provided with the door and pad locking arrangement. The Compartment Illumination lamp with door operated switch shall be provided for M1) & LV compartment, roof is 6 degree inclined to avoid water login during rainy season. As per IEC 62271-202 - 01 set E) INTERCONNECTION AND EARTHING Interconnection Between HT switchgear & Transformer using 1Cx3Rx95 Sq.mm XLPE Single Core Aluminum Unarmored Cable & Interconnection between Transformer & LT switchgear using Aluminum Busbars with aluminum flexible. Internal earthing connections by using 50X6mm GI strips including Transformer Neutral.-01 set

Item No. 36 (Contd……) Notes: (i) CSS, RMU, Vacuum Interrupter, ACB/MCCB shall be of same make for better reliability, performance and service support and overall life cycle optimization. (ii) The Package Substations offered must be type tested as per IEC 61330/62271-202. The copy of type test summary should be submitted along with the tender & Type tests shall be conducted on CSS as per IEC 62271-202 in the name of OEM. (iii) Only original manufacturers equipment is accepted. (iv) The quoted rates deemed to be inclusive of necessary civil work like PCC foundation, brick work required at site for installation of compact sub-station with necessary nuts, bolts, washers etc., required at site and all as directed by Engr-in Charge

S&F of hot dip galvanized perforated type factory made cable tray of size 300X 75X 2mm thick complete with coupling plate bends MS brackets for support and clamps for fixing of cable on the tray including nut bolts washers and other fixing materials complete all as specified and as directed by Engineer-in-Charge.

Supply, fixing, testing and commissioning LT Panel double door, cubical type floor outdoor type mounted 3 phase 4 wire 50 cycles, 415 volts. The panel board shall be made of 3.15 mm thick CRCA sheet for load bearing members and 2 mm thick for doors/covers/partitions and shall be factory powder coated on both sides. The panel shall be provided with separate compartment for each switch gear with hinged door. The panel board shall be suitable for AC, 415 Volts, 50 Hz, 3 phase, 4 wire supply complete with 2000 Amps rated high conductivity aluminium bus bars for phases and neutral, colour coaded with heat shrinkable sleeves pre-wired with copper cable. CPRI for manufacturing firm shall be produced The panel shall be accommodate complete with instrumentation such as Digital multifuction meter, Phase indicating lamps etc., for indicating incoming/out going supply and comprising of the followings items:- Notes :- The quoted rate deems to be inclusive of necessary PCC foundation and brick work required at site for installation of LT Panel board with necessary lugs, nuts & bolts with washers etc required at site and all as directed by the Engr-in-Charge. (a) LT ACB, operational voltage 660V, insulation volt 1000V, AC, 50 cycles, 3--phase 4 pole Electrical Draw out type rated current 1250A of breaking capacity 50kA with quick make, quick break, electrical operating mechanism with triple mound

Item No. 38 (Contd……) current transformer, microprocessor based over current release adjusted short circuit release, earth fault release with shunt trip with indication under voltage release and wired for indicating trip healthy circuit ancillary switch etc. complete for over load release rating 400-800 Amps. (b) MCCB 415V, 4 pole with adjustable thermal & fixed magnetic setting, 400 Amps 36KA, - 03 No (for Outgoing for G/floor & f/Floor & Spare) (c) MCCB 415V, 4 pole with adjustable thermal & fixed magnetic setting, 200 Amps 36KA, - 03 No (for Outgoing for EOT & Lift & Spare) (d) MCCB 415V, 4 pole with adjustable thermal & fixed magnetic setting, 160 Amps 36KA, - 02 No (for Outging & Spare) (e) MCCB 415V, 4 pole with adjustable thermal & fixed magnetic setting, 63 Amps 25KA, - 02 No (for Outging ) Supply of 1250 RATED MAIN PANEL Type of Enclosure: Outdoor Floor Mounted Type. Body: 3.15 mm Thick sheet. Partitions/Doors: 2 mm Thick Sheet. painting: Power Coating: RAL 7035. Switchgear: As per OEM

Supply & Fix in repairs LT Panel double door, cubical type floor indoor type mounted 3 phase 4 wire 50 cycles, 415 volts. The panel board shall be made of 2 mm thick CRCA sheet for load bearing members and 2 mm thick for doors/covers/partitions and shall be factory powder coated on both sides. The panel shall be provided with seperate compartment for each switch gear with hinged door. The panel board shall be suitable for AC, 415 Volts, 50 Hz, 3 phase, 4 wire supply complete with 500Amps rated high conductivity aluminium bus bars for phases and neutral, colour coaded with heat shrinkable sleeves pre-wired with copper cable. CPRI for manufacturing firm shall be produced The panel shall be accommodate complete with instrumentation such as Digital display amphere meter and volt meter, Phase indicating lamps etc., for indicating incoming/out going supply and comprising of the followings items:- Note:- The quoted rate deems to be inclusive of necessary PCC foundation and brick work required at site for installation of LT Panel board with necessary lugs, nuts & bolts with washers and connecting up of old existing UG cables etc required at site and all as directed by the Engr-in-Charge. (a) MCCB 415V, 4 pole with adjustable thermal & fixed magnetic setting, 400 Amps 36KA - 01 No (for Incommer ) (b) MCCB 415V, 4 pole with adjustable thermal & fixed magnetic setting, 200 Amps 35KA, - 02 No (for Outgoing & Spare )

Item No. 39 (Contd……) (c) MCCB 415V, 4 pole with adjustable thermal & fixed magnetic setting, 160 Amps 35KA, - 02 No (for Outgoing & Spare ) (d) MCCB 415V, 4 pole with adjustable thermal & fixed magnetic setting, 100 Amps 35KA, - 02 No (for Outgoing & Spare ) (e) MCB TPN Pole 32 Amps 25KA, - 02 No (for Outging ) (f) MCB SPN Pole 40 Amps 25KA, - 04 No (for Outging ) Supply of 400A RATED MAIN PANEL Type of Enclosure: Indoor Floor Mounted Type. Body: 2 mm Thick sheet. Partitions/Doors: 2 mm Thick Sheet. painting: Power Coating: RAL 7035. Switchgear: As per OEM

Supply, intallation, testing and commissioning of HT 11KV switch board panel indoor type consisting of motorised automated VCB's (as 01 X incomer & 02 X outgoing) totally enclosed, 630 Amps, 350 MVA, 11 KV fully draw out type/ cassette type breaker as per IEC 62771-100/200 single break trip free breaker with motor operated spring charge mechanism mounted on truck carriage suitable for horizontal isolation, horizontal draw out type complete with self contained fully interlocked rack in rack out mechanism Breaker is featured with mechanical ON and OFF indicator with hand trip device breaking capacity of 25 KA for 3 Sec. The busbar rating shall be 800 Amps for complete switch gear. The switch gear panel shall be of sheet steel construction with Aluminium Zinc coating not less than 2.5mm thickness for load bearing section and not less than 2mm thickness for none load bearing and shall totally dust & vermin proof, indoor type, standing floor mounted type, compartment based self supported insulated busbar with full voltage rated should be used. VCB panel shall be confirming to IS13947 with latest amendment and IP-42. Class of protection comprising of necessary busbar extension and connection, circuit breaker shall be completely encapsulated in epoxy housing. 110 volt DC Battery Bank (55 Nos x 2 volt) alongwith battery charger to be Incomer-01 No provide & connected to 11 KV HT panel with suitable control cable. Incomer: 01 No. (a) One triple pole 11KV, 350MVA, 630 Amps, VCB fitted with all necessary control devices.

S & F MCCB 415V, 4 pole with adjustable thermal & adjustable magnetic setting, 200A, 36KA with sheet Metal enclosure complete all as specified and as directed by Engineer-in-Charge.

S & F MCCB 415V, 4 pole with adjustable thermal & adjustable magnetic setting, 160A, 36KA with sheet Metal enclosure complete all as specified and as directed by Engineer-in-Charge.

S & F MCCB 100 Amps 4 pole 36 KA with sheet Metal enclosurecomplete all as specified and as directed by Engineer-in-Charge.

S & F MCCB 63 Amps 4 pole 36 KA with sheet Metal enclosure complete all as specified and as directed by Engineer-in-Charge.

S & F MCB TPN 32 Amps with sheet Metal enclosure complete all as specified and as directed by Engineer-in-Charge.

M&L for Earthing complete with galvanised steel earth plate electrode 60cm X 60cm X 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron strip 32×6mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 of SSR Part-I, including excavation / earth work in any strata, adequate quantity of charcoal and common salt, PCC chamber with RCC 1:2:4 type B1 40mm thick cover slab with 8mm dia TMT bars @150mm c/c in both ways, suitable handle and angle iron frame of suitable size to fix the cover, with 20mm bore GI pipe light grade for watering with funnel, wire mesh and 40mm bore GI pipe medium grade for protection of galvanised iron strip 32×6mm, including testing after completion and complete all as specified and as directed by Engineer-in-Charge. Note : Earth strip will be measured after 7.5mtr from the earth strip or earth testing terminal block whichever is lesser under relevant item.

Supply, lay in trenches, ducts, connect, test and commissioning Ductile Iron pressure pipe of size 150mm dia with flanged and confirming to IS-8329 : 2000 in standard maximum lengths, class K-9, flange rating PN-10, including necessary gasket and special items/fittings pipes lining inside with cement mortar (CML) outside with bituminous coating as per Annx `C' of IS-8329, complete all as specified and as directed by Engineer-in-Charge. Note: Necessary earthwork and fittings shall be measured and paid separately.

Supply, lay in trenches, ducts, connect, test and commissioning Ductile Iron pressure pipe of size 100mm dia with flanged and conforming to IS-8329 : 2000 in standard maximum lengths, class K-9, flange rating PN-10, including necessary gasket and special items/fittings pipes lining inside with cement mortar (CML) outside with bituminous coating as per Annx `C' of IS-8329, complete all as specified and as directed by Engineer-in-Charge. Note: Necessary earthwork and fittings shall be measured and paid separately.

Supply and fixing AFFF type fire extinguisher - mechanical foam type 9 litres capacity complete with initial charge, gun metal cap, discharge hose with nozzle, wall fixing brackets, etc., complete all as specified and as directed by Engineer-in-Charge.

Supply and fix light weight screw grip type CO2 fire extinguishers - 4.5 Kg capacity complete with initial charge, gun metal cap, discharge hose with AB horn, nozzle, wall fixing brackets etc confirming to IS : 15683 with ISI mark complete all as specified and as directed by Engineer-in-Charge.

Supply and fix Dry chemical powder stored pressure type - 9 Kg capacity complete with initial charge, fund metal cap, discharge hose with nozzle wall fixing brackets etc confirming to IS:15683 with ISI mark complete all as specified and as directed by Engineer-in-Charge.

M&L for fabrication and erection of fire stand of suitable size made out of angle iron/channel and paint two coat of post office red colour synthetic enamel paint over a coat of red oxide primer and lettering with white paint including galvanised MS fire bucket- 04 Nos, 5 litre capacity, complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Voltage stabilizer with copper winding for automatic operation, single phase naturally air cooled Indoor type and designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of +2.5% and of capacity 3 KVA complete all as specified and as directed by Engineer-in-Charge.

Supply and installed Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & disigned for input variation between 170 Volts to 250 V with output voltage stabilised at 230 V with accuracy of + 2.5% and of capacity 5 KVA complete all as specified and as directed by Engineer-in-Charge.

Taking down 1200mm dia MS pipe from upto 2 meter depth of trenchs used by crane or any other hydralic equipment as per site required complete all as specified and as directed by Engineer-in-Charge. Note: Necessary earthwork shall be measured and paid separately

Material and labour for 1200mm dia ERW MS pipe 12.7 thickness with all fittings and fixtures complete all as specified and as directed by Engineer-in-Charge.

Cutting of existing MS pipe of 1200 mm dia for alteration/ addition complete all as specified and as directed by Engineer-in-Charge.

Divertion of exisitng HT/LT Cable of variuous sizes and any core upto 500 Sqmm with and including jointing materials complete all as specified and as directed by Engineer-in-Charge. Note: Necessary earthwork shall be measured and paid separately

Supply, installation, testing and commissioning of Microprocessor based intelligent adressable networking type fire alarm panel with 4 x 20 Alpha numeric LCD display, EN54 Standreds Event logging and printing facility, Real time clock & RS-485 port to connect repeater panel via 4 wires, Keyboard programming with password locking. Provision of RS-232 for LAN connection with 12 Hrs backup facilty UPS system for AFDC panel . Provision of connecting Fire Fighting equipments as required to areas specified complete all as specified and as directed by Engineer-in-Charge. Note: (i) One loop micro processor

Supply, installation, testing and commissioning of Microprocessor based intelligent adressable type fire alram repeat panel EN54 Standrerds with 4 x 20 Alpha numeric LCD display,Keyboard programming with passowrd locking.Provision of connecting Fire alarm repeat equipments as required to areas specified complete all as specified and as directed by Engineer-in-Charge.

Supply, installation, testing and commissioning of intelligent analogue addressable multi criterion detectors combination of Heat and Smoke below false ceiling/ on ceiling including the cost of base plate. 75 mm dia MS outlet box for fixing of the detector base, mounting accessories etc., complete all as specified and as directed by Engineer-in-Charge.

Supply, installation, testing and commissioning of intelligent addressable Manual Call point resettabel made of ABS/cas aluminium for indoors and outdoors with Fire indication, complete all as specified and as directed by Engineer-in-Charge.

Supply, installation, testing and commissioning of 2 core x 1.5 copper armored FRLS cable as per IS: 1554 of fixed on wall/ceiling mounting complete with fixing arrangements.

Supply, installation, testing and commissioning of addressable wall mounting, strobes cum hooters including the cost of mounting accessories complete as per specifications and as required including testing and commissioning complete all as specified and as directed by Engineer-in-Charge.

Design, manufacture supply, install, testing & commissioning electrically operated double grider OH Crane of capacity 5.0 Ton, with a span of not exceeding 09mtrs, hook height not exceeding 6 mtrs, long travel not exceeding 14 mtrs including provision of pendent push button apart from radio remote control with micro speeds (VFD) with including following items complete all as specified and as directed by Engineer-in-Charge. (a) Main Hoist speed -3.0 mtrs/min (b) Safe load indicator (c) Bus bar maintenance cabin to be provided. (d) Safety railing along one (Ladder) side of the Long travel track to be provided. (e) Safety railing on both End Carriages to be provided. (f) Ladder with caging to be provided. (g) Supply of tools as per the list of OEM specifications. (h) Supply of spares for two years operationa nd normal maintenance as per the list of OEM specifications. (j) Bridge Lamps to be provided. Notes: (a) Span and long travel vary slightly as per site condition. (b) Load test at site to be carried out in presence of rep. of Accepting Officer. (c) Factory test including load test to be carried out in presence of rep of Accepting Officer.

Design, manufacture, supply, install, testing & commissioning of goods lift 5 Ton , speed 0.5 metre/sec with single speed motor, 415 volts, 3 phase AC 50 Hz supply, conforming to IS-14665 and as amended, suitable to serve G+02 upper floors with AC Variable Voltage & Variable Frequency Drive (VVVF drive) complete with all standard accessories, simplex automatic & manual dual controlled operation with/without attendant, centre opening doors with door drive (electric motor driven mechanism), sliding stainless steel doors, automatic rescue device (ARD) system, 3D infra red sensor in full height of door & built in announcing system without hand set (03 Nos, one each in car, Machine room & near Ground floor landing door) complete all as specified and as directed by Engineer-in-Charge. Comprising of the followings items/specifications:- (a) Head Room Height: 5000mm(required) (b) Car Dimensions: 2800mm wide x 3500 mm deep x 2500mm high. (c) Door Dimensions: 2400mm wide x 2300mm internal height. (d) Door type: Six panel centre operating door panel 4. (e) Car Panel Finish: ST4 Silver brushed StSt. (f) Ceiling & Lighting: Single ceiling tile(CT002) Brushed stainless steel Hairline AISI441. (g) Car Door Finish: Brushed stainless steel SUS304(ST4). Note: Design drawing to be submitted before manufacturing for approval of Accepting Officer.

Supply and fix including testing & commissioning of 30 KVA UPS with 30 minute backup three phase AC input 300 to 450V and output 415Volt (+/-) 1% complete with 12V, 150AH tubular batteries of adequate numbers(required No's not less than 32) with provision of stand/table complete all as specified and as directed by Engineer-in-Charge.

SRI SURYA PROJECTS (BID ID -3331528)

anjaliinfratech (BID ID -3330694)

CIVILEC ENGINEERING WORKS (BID ID -3331433)

MURALI KRISHNA ASSOCIATES (BID ID -3331513)

P Govinda Reddy Infrastructure (BID ID -3331864)

Mahamaruti Constructions (BID ID -3331310)

MOUNIKA ENTERPRISES (BID ID -3325787)