Tender for renovation of New and Old Guest House building at BPSMV Khanpur Kalan.

Amount

Distempering with 1st quality acrylic distemper (Ready mix) having voe content less than 50 grams/ litre of approved brand and manufacture to give an even shade:.( HSR- 30.25)

Finishing walls with Acrylic Smooth exterior paint of required shade : Old work (Two or more coat applied @ 1.67 litre/ 10 sqm) on existing cement paint surface (HSR-30.37.1)

Painting (two or more coats) on Cl/SCI rain water, soil waste and vent pipes and fittings with black anticorrosive bitumastic paint of approved brand and manufacture, over and including a priming of ready mixed zinc chromate yellow primer on new work: -100 mm diameter pipes. (HSR -11.101.2)

Polishing on wood work with ready made wax polish of approved brand and manufacture : (HSR-30.33)

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. (HSR-5.48)

Providing and Fixing Poly Carbonate Sheet 1.25mm thickness on Gates and sqm grills excluding the cost of MS framework but including the cost of nut bolts, Welding rods complete in all respect as per direction of Engineer-in-Charge. (HSR-13.20)

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.(HSR-5.45)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) llnd course of 20 mm cement plaster 1 :3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) lllrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) lvth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen@ 1.7 kg/sqm). (HSR- 28.14)

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead. Thickness above 10 mm up to 25 mm (HSR-5.46.2)

1Half brick masonry with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level Cement mortar 1:3 (1 cement :3 coarse sand) (HSR-7.28.1)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor four level, excluding the cost of centering, shuttering and finishing: 1 : 1 ½: 3 ( 1 cement : 1 ½ coarse sand (zone-Ill) : 3 graded stone aggregate 20 mm nominal size). (HSR-6.2.1)

Centering and shuttering including strutting, propping etc. and removal of form for Shelves (Cast in situ) (HSR-6.30.4)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. Cold twisted bars (HSR-6.33.3)

12 mm cement plaster of mix : 1 :4 (1 cement: 4 fine sand) (HSR-11.5.3)

Removing white or colour wash by scrapping and sand papering sqm and preparing the surface smooth including necessary repairs to scratches etc. complete (HSR-30.21)

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete(HSR-11.58)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: (HSR-11.67)

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead: Of area 3 sq. metres and below (HSR-5.29.1)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid separately). Second class teak wood (HSR-12.1.1)

Providing and fixing aluminium sliding door bolts, ISi marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm (HSR-12.98.2)

Providing and fixing ISi marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISi marked Stainless Steel butt hinges with sqm necessary screws (HSR-12.36.1)

Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screw Second class teak wood (HSR-12.32.1.1)

Providing and fixing ISi marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:100x63x3.2 mm (HSR-12.97.5)

Providing and fixing aluminium tower bolts, ISi marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete 150x10 mm (HSR-12.99.4)

Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete 100 mm (HSR-12.102.2)

Dismantling cement conglomerate / terrazzo floors 25 mm to 50 mm manually/ by mechanical means and disposal of material within standard lead as per direction of Engineer- in-charge. (HSR-5.42)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 1 :4: 8 ( 1 Cement : 4 coarse sand (zone-Ill) : 8 graded cum stone aggregate 40 mm nominal size) (HSR-6.1.6)

Providing and laying of conglomerate floor 50mm thick cement concrete topping 1 :2:4 (HSR-10.7)

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm7 or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1 :4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.(HSR-10.60)

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1 :3 (1 cement : 3 coarse sand) and jointing with grey cement slurry@ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (HSR-10.62)

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge In cement mortar (HSR-5.7.4)

10 cm thick (average) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1: 1 (1 clay : 1 cow dung) and covered with flat tile bricks, grouted with cement mortar 1 :3 (1 cement: 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement and finished neat: With common burnt clay non-modular brick tile of class sqm designation ( HSR-9.11.1)

Providing gola 75x75 mm in cement concrete 1 :2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1 :3 (1 cement : 3 fine sand) as per standard design In 75x75 mm deep chase (HSR-9.17.1)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600x600 mm (HSR-10.63.2)

Providing and fixing rectangular high density polyethylene water storage loft litre 7 8 tank with cover, conforming to ISi : 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately. (1000 Ltr.. Capacity each tank X 2 nos.) (HSR-22.182)

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighting not less than 810 gms. 15 mm nominal bore (HSR-22.105.1)

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore (HSR-22.107.1)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore (HSR-22.103.1)

Making khurras 45x45 cm with average minimum thickness of 5 cm cement each 77 88 165 concrete 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1 :3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete (HSR-9.18)

Pointing on tile brick work with cement mortar 1 :3 (1 cement : 3 fine sand): Flush/ Ruled/ Struck or weathered pointing (HSR-11.26.1)

Brick work with common burnt clay non-modular bricks of class designation 7 .5 in superstructure above plinth level up to floor IV level in all shapes and sizes in : Cement mortar 1:4 (1 cement: 4 coarse sand) (HSR- 7.22.1)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White vitreous chinaware Wash basin size 630x450 mm with a each pair of 15 mm C. P. brass pillar taps (HSR-22.1.1)

Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles & rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shall have one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screw holding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mmx 1 mm, painted with primer , all four comers of reinforcement to be welded or sealed. Solid PVC extruded bidding (push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solvent cement & self driven self tapping screws. Single piece extruded solid PVC lock rail of size 100 mm x 30 mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100mm x 8 mm complete as per manufacturer's spec ifications and direction of Engineer-in-charge. Decorative finish (both side wood grained finish) (HSR-12.122.2)

Providing and fixing of reconstituted stone tile work (IS 3622-2017- sqm Reaffirmed) for wall Cladding up to 10 m height with special adhesive (IS 15477-2019) over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade (HSR-8.16)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work· Exposed on wall 15 mm dia nominal bore (HSR-22.88.1)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work· Exposed on wall 20 mm dia nominal bore (HSR-22.88.2)

C.P. Brass fountain fittings complete set (B-1348)

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. (HSR-5.49)

Fabrication of uPVC extruded casement /sliding window and doors including drilling hole, fixing of fitting & hardware, hire charge of drill machine and elecricity charge etc. ( HSR- J.B.001)

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). (HSR-13.41)

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 20mm dia (HSR-22.14.2.2)

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste coupling 36 mm dia of 83 mm length and 77mm breadth, each weighing not less than 60 gms ( HSR-22.115.2)

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete: White solid plastic seat with lid (HSR-22.36.1)

Providing and fixing 100 mm sand cast Iron grating for gully trap. (HSR-22.19)

Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter (HSR-9.57.2)

Bend 87.5° 110 mm bend (HSR-9.58.5.2)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade One or more coats on old work (HSR-30.28.1)

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty: Float glass panes of nominal thickness 4 mm (weight not less than 1 Okg/sqm) (HSR-30.54.1)

Dismantling wire gauze with frame work including separating frame Frame work and putting wire gauge into rolls. (Old HSR-8.14)

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. sqm wire and 1.4mm wide aperture with matching wood beading (HSR-12.9.8)

Applying priming coat: With ready mixed pink or Grey primer of approved brand andmanufacture on wood work (hard and soft wood) (HSR 11.68.1)

Supply & fixing Windows frames (Chowkhats) including mullions consisting frame fabricated from sheet roll formed out of 1.2mm thick galvanized sheet as per IS:277 (Base steel as per IS 513) with zinc of 120 gm/sqm & Powder coated with pure Polyester powder up to 50 microns (as per approved colour), 3 Nos. 100mm butt - hinges 2mm thick, 6 Nos. 1.2mm thick CRCA electroplated stiffner, 6 Nos. M.S hold fast with split and tail welded to stiffner plate 200mm long, receiver for aldrop, weld less corner assembly with brackets & screws, M.S tie rod 50mm x 25mm to be fixed at bottom finished with powder coated total thickness of coating 0.6mm of approved shade, fixed in position including the cost of cement concrete for 1 :2:4 for fixing lugs complete in all respects as per drawing, design, specification & entire satisfaction of Engineer-in-charge. Door Frame of size 125mm x 60mm with 37mm wide double rebate for 35mm door shutter (HSR 13.21.2)

Supply & fixing Windows frames (Chowkhats) including mullions consisting frame fabricated from sheet roll formed out of 1.2mm thick galvanized sheet as per IS:277 (Base steel as per IS 513) with zinc of 120 gm/sqm & Powder coated with pure Polyester powder up to 50 microns (as per approved colour), 3 Nos. 100mm butt - hinges 2mm thick, 6 Nos. 1.2mm thick CRCA electroplated stiffner, 6 Nos. M.S hold fast with split and tail welded to stiffner plate 200mm long, receiver for aldrop, weld less corner assembly with brackets & screws, M.S tie rod 50mm x 25mm to be fixed at bottom finished with powder coated total thickness of coating 0.6mm of approved shade, fixed in position including the cost of cement concrete for 1 :2:4 for fixing lugs complete in all respects as per drawing, design, specification & entire satisfaction of Engineer-in-charge. Door Frame of size 80mm x 50mm with 37mm wide double rebate for 35mm door shutter (HSR 13.21.1)

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 356 4, embossed on the body, door weight up to 35 kg and door width up to 7 00 mm), with necessary accessories and screws etc. complete. (HSR-12.88)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. d All kinds of soil. (HSR-4.14.1)

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand) (HSR-7.20.1)

Constructing brick masonry inspection Chamber sizes as given below up to 0.60 metre average depth in cement mortar 1 :5 lime concrete with 40 per cent lime mortar 2:3 in foundation cement concrete 1 :2:4 benching 12mm thick cement plaster 1 :2 with a floating coat of 1 mm thick of neat cement R.C.C. 1 :2:4 slab 100 mm thick/cement concrete topping, 50mm thick: with 455mmx455mm / 455mm x610mm inside light duty C.I. inspection chamber cover and frame weight as per 1.5.1. specification painted with 3 coats of black bitumastic superior paint complete as per standard design. 21.84.1 Size 450 mm X450 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with C.C. topping (HSR-21.84.1)

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 1 O mm gap for thermal expansion coupler. - 110mm (9.58.1.2)

Providing and fixing on wall face Unplasticised - PVC moulded fittings/ accessories for Unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 1 O mm gap for thermal expansion. - Single tee without door - 110x110x110 mm (HSR-9.58.4.2)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore (HSR-22.98..1)

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. 1 o litre capacity - White (HSR-22.39.1)

Providing and fixing Unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm lengt (HSR-22.128.2)

Providing and fixing M.S. stays and clamps for sand cast iron/ centrifugally cast (spun) iron pipes of diameter :- 100mm (HSR-22.79.1)

Providing & fixing water storage tank cover best qualitycomplete in all respects make ravindra/ jindal etc (NS item)

Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. TRIPLE POLE MCCB 16 to 100 Amp HSR-23.22.1.3

Supply and erection of miniature circuit Breaker/isolator 240/415 V in the existing distribution board including making necessary connections:- 6 amp. to 32 amp Single Pole HSR - 23.22.5.1

Supply and erection of miniature circuit Breaker/isolator 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. MCB's FOUR POLE HSR - 23.22.5.8

Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Ceiling rose flush/surface type HSR 23.8.1.5

Fixing of LED Down lighter 7 to 28 Watt on ceiling or in false ceiling , including cutting/making hole in ceiling including making connections etc as required HSR - 23.21

Painting of pole with brackets etc with 2 coats of enamelled paint or other approved paint. 3 metre and above ,Up to the height of 5 metres. HSR - 23.19.1

Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. (but without charcoal or coke and salt) as required. HSR - 24.1.1

Extra for using salt and char coal/coke for pipe earth electrode as required. HSR - 24.1.2

Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop carthing as required. HSR - 24.1.13

Supply and erection of 20mm x 3 mm thick GI, tape fixed with suitable G.I. stapples of same size. HSR - 24.1.4

Supply, laying and erection of aluminium conductor XLPE insulated PVC sheathed armoured and served cable 1100 volts grade as per IS 7098 (Part-1)1988 to be laid loose in the existing trench or pipe as per PWD General Specifications Overall size 6sq.mm (2Core) Armoured (Loose) CSR - 34.10 (i)

Supply and erection of suitable compression type brass cable glands for underground Cable Upto 6 Sq mm cable 2 to 4 Core HSR - 24.2.7.1

4.5metres long 50 mm dia pole duly embeded 0.75 m below ground level. HSR-24.4.1.2

Supply and erection of weather proof M.S. box size 20 cm * 15 cm * 10 cm covered with 3.00 mm thick M.S. sheet hinged cover, locking arrangement, housed in wall, including the cost of 1 no. 16 amp. 415 volts SPMCB and 2 no. 63 amp. 415 volts neutral links fixed on hard wood board/ 10 mm Bakelite sheet in the M.S. box including painting and necessary connections. HSR - 24.4.16

Supply and erection of weather proof M.S. box size 20 cm * 15 cm * 10 cm covered with 3.00 mm thick M.S. sheet hinged cover, housed in1:3:6 cement concrete muff including suitable size of PVC pipe for incoming & outgoing cables,including the cost of 1 no. 16 amp. 415 volts SPMCB and 2 no. 63 amp. 415 volts neutral links fixed on hard wood board/ 8 mm Bakelite sheet in the M.S. box including the cost of locking arrangement, painting and necessary connections etc. (Muff size 40cm dia 50 cm high) HSR - 24.4.17

Replacement of ball bearing of a ceiling fan including greasing, re-assembling and testing etc. HSR - 23.15

Supply and erection of aluminium lugs heavy duty including crimping etc. upto the entire satisfaction of the Engineer-in-charge of the work. 4 sqmm to 6 sqmm HSR - 24.2.8.2

Wiring main and sub mains in two single core for phase and neutral wire and one single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in existing MS/PVC Conduit etc as required. 1 run of Size 1.50 Sqmm(1/1.40mm) HSR - 23.5.6.1

1 run of Size 4 Sqmm(1/2.24mm) HSR - 23.5.6.3

Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work PVC pipe of 25 mm dia. HSR - 23.7.6.2

Supply and erection of MS Saddle and clamps including the cost of all labour and material required to complete the job in all respect and upto entire satisfaction of the Engineer-in-charge of work. EL035

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect.5 amp 1 way switch HSR - 23.8.11.1

15 amp 1 way switch HSR - 23.8.11.3

5 amp Socket HSR - 23.8.11.4

15 amp 6 pin Socket HSR - 23.8.11.5

step type Fan Regulator 2 modules 300 watt HSR - 23.8.11.7

Blanking plate HSR - 23.8.11.10

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 4 Modules HSR-23.8.10.3

6 Modules HSR-23.8.10.4

8 Modules HSR-23.8.10.5

12 Modules HSR-23.8.10.6

Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall/ceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. PVC pipe of 40 mm dia. HSR-23.7.6.4

S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Mtr below ground level including diging and refilling of earth including cost of suitable size socket/cuppler for HDPE pipe including the cost of labour and material required to complete the job in all respect up to the entire satisfaction of Engineer in charge of the work. DWC/HDPE pipe 63/50 mm outer dia/inner dia HSR-24.5.2.3

Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. 4 pole MCCB 300 to 400 amp HSR-23.22.1.12

Supply and erection of miniature circuit Breaker/isolator 240/415 V in the existing distribution board including making necessary connections 6 amp. to 32 amp Double POLE HSR-23.22.5.3

Supply and erection of U- PVC Trunking/Channel of following size including cost of fixing on wall, floor and ceiling etc. with required material complete the job in all respect up to entire satisfaction of the Engineer-in-charge of work. 50x50 mm HSR-23.23.5.4

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to to the entire satisfaction of the Engineer-in-Charge of the work. TPN DB Horizontal type Double Door 6 way ( 8 incoming 3phase*6 outgoing) HSR-23.22.4.6

Supply and erection of sheet steel enclosures 1pole/ 2 pole/4 pole including providing SP/DP/TP/FP MCB on wall/on existing pedestal complete with necessary connections etc, SP enclosure suitable for single pole MCB HSR-23.22.3.1

Supply and erection of miniature circuit Breaker/isolator 240/415 V in the existing distribution board including making necessary connections:- 40 amp to 63 amp. Double pole HSR-23.22.5.4

Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Switch 5 amp. on existing sheet. HSR-23.8.1.1

Wall socket 5 amp on existing sheet. HSR -23.8.1.2

15 amp. switch on existing sheet. HSR - 23.8.1.3

6 pin 15 multi socket on existing sheet HSR - 23.8.1.4

Bakelite angle/straight button holder large size. HSR - 23.8.1.12

Supply and Fixing Bakelite sheet on existing MS/GI/wooden/PVC box etc including fixing with brass screws and washers. 5 mm thick HSR-23.8.2.1

Supply and erection of 32mm dia metre 1.5 m long bracket (B-class) making an angle of 10° to 15° with horizontal plane for mounting street light fitting fixing of GI. bracket on wall with 2 nos. 32 mm x 3 mm thick M.S. clamps including cost of cutting, welding of G.I. pipe complete with cement sand mixture, bolts and nuts etc. including necessary connections. HSR- 24.4.3

Supply and erection of Single Phase weather proof M.S. box of size 20 cm x 15 cm x 10 cm with hinged cover made of 2 mm thick MS sheet, locking arrangements, housed in wall/fixed on pole , including the cost of 1 no 4 way 16 A bakellite connector, 1 no. 6 amp SP MCB and 1 Nos. 16 amp. neutral links fixed on bakellite sheet in the M.S. box including painting and necessary connections. HSR-24.4.5

Wiring only in 1.5 sqmm PVC insulated copper conductor cable for LIGHT/FAN/Call bell point in existing conduit pipe and MS boxes including cost of Bakelite cover for MS box, switch, wall socket, ceiling rose/connector etc. Group A HSR-23.5.1.1

Wiring in existing conduit and MS box for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm FRLS copper wire and 1no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6 Amp 3/5 pin socket and 1 no 5/6 Amp switch etc complete as required Group A HSR-23.5.4.1

Wiring in existing conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1 no 15/16 Amp 3/6 pin socket and 1 no 15/16 Amp switch etc complete as required Group A HSR-23.5.5.1

Supply erection testing of Ceiling fans IS marked (as per IS code 374) with sultable GI pipe complete in all respects complete as per directions of Engineer-in-Charge 56'' (1400mm) HSR-2071

Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Socket size rotary step type Electronic regulator for A.C. ceiling fan HSR-23.8.1.13

Supply and erection of suitable MS/GI Box covered with 3 mm thick Bakelite sheet as below 200 mm X 150 mm X 60 mm deep metal box HSR-23.8.3.4

300 mm X 150 mm X 60 mm deep metal box HSR-23.8.3.5

Supply and erection of LED Street Light fitting 60watt. Colour temerature 6500k make Havells model no. ENDURAOMNIPLUSSL60WLED757SASYTOPC / Philips model no. BRP062LED65CWSLAS1PSU & Wipro model no. LR02-671-XXX-57-G3 with (Warranty 2 year) complete in all respect up to the entire satisfaction of Engineer - in charges of the work NS

Supply & Erection of heavy duty exhaust fan 12" (300mm sweep) make Crompton, Bajaj, Havells, Orient with (Warranty 2 year) in all respect up to the entire satisfaction of Engineer-in charges of the work. NS

Supply and erection of LED Batten tube light fitting 20 watt. Make Havells, Model no. LUMILINEBS20WLED865PCWH / Philips model no. 021CLED225PSUCWGR & Wipro model no. GARNET20WLEDD532065 with warranty 2 year complete in all respect up to the entire satisfaction of Engineer-in charges of the work. (NS)

SITC 2x18W t8 LED 1200mm Batten Light. The Endura Fixture is a surface & wall mounted LED batten with extruded aluminium housing and robust construction. PF>.95, System Wattage LED 2x180W With minium 1500 lumens in 5700k. The fixture should be of Makes :- Bajaj (Batton 112182 BLRD-DB218+TUBE LIGHT 112432 BLRB 2x18W CWC) / PHILIPS / GE / OSRAM / CGL with (Warranty 2 year) NS item

Supply & Erection of LED Flood Light Fitting 200watt. make Havells model no. JETAVALOURFL 200W LED 757 PINTWBLTG/ Philips make model no. BVP483PLED210X2CWSWBPSUP4145/and Wipro Make model no. LF30-272-060-57-XX as per minimum Warranty 2 year, IP rating – IP66, Colour temperature - 5700K and all latest updated specification Complete in all respect up to the entire satisfaction of the Engineer-in- charge of the work. (NS)

Supply & Erection of heavy duty exhaust fan 15" with double ball bearing (380mm sweep) make Crompton, Bajaj, Havells, Orient with (Warranty 2 year) in all respect up to the entire satisfaction of Engineer-in charges of the work. NS item

Supply & Erection of Exhaust fan shutter 15" (380 mm) Aluminium body Complete in all respect up to the entire satisfaction of Engineer - in charges of the work. NS item

Supply & Erection of Exhaust fan shutter 12" (300 mm) Aluminium body Complete in all respect up to the entire satisfaction of Engineer - in charges of the work. NS item

Supply & Erection of inverter 2000VA shinewave make microtek or equivalent make of luminous with (Warranty 2 year) Complete in all respect up to the entire satisfaction of Engineer-in charges of the work. NS item

Supply & Erection of inverter battery 150AH with trolley make Exide or equivalent make of Luminous, microtek with (Warranty 4 year) Complete in all respect up to the entire satifaction of Engineer-in charges of the work NS item

Supply and erection of LED Decorative post-top energy saving symmetrical light with high power LEDs, spun aluminium landscape luminaire light 35watt. make Havells model no. CORALPT35W LED757PSYMTOPC or equivalent make & Model of ,Philips & Wipro with (Warranty 2 year) complete in all respect up to the entire satisfaction of Engineer-in Charges of the work. NS item

AMAN ATTRI

M/s Ahmed Builders